Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermal ignition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Experimental investigation of air-fuel equivalence ratio effects on advanced dual-fuel ammonia/diesel combustion on a single-cylinder medium-duty diesel engine at high load

Ammonia (NH 3 ) has garnered significant interest as an alternative fuel for meeting international emissions reduction mandates in sectors with high weight and distance requirements, such as shipping. Technical barriers and unanswered questions remain on the combustion strategies that can maximize ammonia utilization and minimize emissions. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH 3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH 3 combustion performance at richer in-cylinder conditions, a global λ sweep compared the use of early (E-pilot) and late (L-pilot) single diesel injections. The experiments were conducted at 1200 RPM and 12.8 ± 0.2 bar (75 % load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90 % ammonia energy substitution level. A diesel injection timing sweep was conducted for both the injection strategies at fixed λ, and the timing with the lowest engine-out N 2 O emissions was identified. The results indicated an optimal balance between CO 2,eq and thermal efficiency benefits both E-pilot and l-pilot injection strategy cases compared with CDC at a λ of 1.4. In conclusion, the indicated nitrogen-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for l-pilot, but no apparent trend emerged for the E-pilot injection strategy at the tested boundary conditions.

Ammonia↗
DOE OSTI2021

Development of an Efficient Conjugate Heat Transfer Modeling Framework to Optimize Mixing-Limited Combustion of Ethanol in a Diesel Engine

Mixing controlled combustion of alcohol fuels has been identified as a promising technology based on their low propensity for particulate and NOx production, but the higher heats of vaporization and auto-ignition temperatures of these fuels make their direct use in diesel engine architectures a challenge. To realize the potential of alcohol-fueled combustion, a computational fluid dynamics (CFD) modeling framework is developed, validated, and exercised to identify designs that maximize engine thermal efficiency. To evaluate the use of thermal barrier coatings (TBCs), a simplified one-dimensional (1D) conjugate heat transfer (CHT) modeling framework is employed. The addition of the 1D CHT model only increases the computational expense by 15% relative to traditional approaches, yet offers more accurate heat transfer predictions over constant temperature boundary conditions. The validated model is then used to explore a range of injector orientations and piston bowl geometries. Using a design of experiments (DoE) approach, several designs were identified that improved fuel-air mixing, shortened the combustion duration, and increased thermal efficiency. The most promising design was fabricated and tested in a Caterpillar 1Y3700 single-cylinder oil test engine (SCOTE). Engine testing confirmed the findings from the CFD simulations and found that the co-optimized injector and piston bowl design yielded over 2-percentage point increase in thermal efficiency at the same equivalence ratio (0.96) and over 6-percentage point increase at the same engine load (10.1 bar indicated mean effective pressure (IMEP)), while satisfying design constraints for peak pressure and maximum pressure rise rate.

Magnotti, Gina M.↗
DOE OSTI2020

Effects of molar expansion ratio of fuels on engine efficiency

Fuel properties have a strong impact on the efficiency of internal combustion engines. Contrary to other physical and thermochemical fuel properties, the molar expansion ratio is normally ignored. Molar expansion ratio is the ratio of number of moles of the products to the reactants. In this work, the impact of the fuel’s molar expansion ratio on engine efficiency is investigated. Findings are based on simulations of a spark ignition engine using different fuels (standard fuels and user-defined fuels) and different dilution ratios. Simulations without heat transfer and friction were performed first. The combustion then takes place at top dead center with a very short combustion duration to approach the ideal Otto cycle. The heat transfer and friction were then added step by step. From this analysis, it could be concluded that the heat loss and friction work decrease as molar expansion ratio increases. The gross indicated and brake thermal efficiencies thus increase. User-defined fuels with different molar expansion ratio, but the same physical and thermochemical properties were then employed. The simulated results showed that the brake thermal efficiency increases by around 1.15% with an increase in molar expansion ratio of 0.02 compared to a fuel with a molar expansion ratio of unity. Lastly, the simulation was also done with air and exhaust gas recirculation dilution.

42 ENGINEERING↗
DOE OSTI2023

Low-carbon fuels for spark-ignited engines: A comparative study of compressed natural gas and liquefied petroleum gas on a CFR engine with exhaust gas recirculation

Decades of work on low-carbon fuels have established their potential for substantial emissions reductions; however, their adoption is still limited by infrastructure concerns and engine efficiency deficits. As infrastructures have begun to evolve, research on strategies that maximize engine efficiency through interactions with fuel properties must also now take center place. This paper compares the performance, emissions, and combustion characteristics of two forefront low-carbon fuels: compressed natural gas (CNG) and liquefied petroleum gas (LPG) in a cooperative fuel research (CFR) engine over a range of compression ratios and engine loads. The effects of exhaust gas recirculation (EGR), end-gas auto-ignition, and a novel combustion control tool, the combustion intensity metric (CIM), were also evaluated at different stoichiometric engine operating conditions. In comparison to LPG, CNG operation demonstrated an extended knock-free regime, allowing engine operation at higher engine loads and compression ratios, but LPG operation exhibited enhanced combustion characteristics with higher peak pressures and faster apparent heat release rates (AHRR). LPG operation achieved higher brake thermal efficiencies and lower equivalent CO 2 emissions compared to CNG operation at the tested engine loads and compression ratios. LPG demonstrated significantly higher EGR tolerance limits compared to CNG, with a maximum of 28% EGR rate, compared to 23% for CNG. This improved EGR dilution tolerance was responsible for a 90% reduction in NOx emissions for LPG compared to a maximum of 70% with CNG. EGR dilution also exhibited more effective knock mitigation potential with LPG, suppressing knock intensity values by up to 98% and transitioning the engine operation towards normal combustion from heavy knocking conditions. As a result, the CIM was found to decrease burn durations and improve the quality of combustion by controlling the desired fraction of end-gas auto-ignition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Lowering the reactor breakeven requirements for proton–boron 11 fusion

Recently, it has been shown that altering the natural collisional power flow of the proton–boron 11 (pB11) fusion reaction can significantly reduce the Lawson product of ion density and confinement time required to achieve ignition. However, these products are still onerous—on the order of 7×1015 cm−3 s under the most optimistic scenarios. Fortunately, a breakeven fusion power plant does not require an igniting plasma, but rather a reactor that produces more electrical power than it consumes. Here, we extend the existing 0D power balance analysis to check the conditions on power plant breakeven. We find that even for the base thermonuclear reaction, modern high-efficiency thermal engines should reduce the Lawson product to 1.2×1015 cm−3 s. We then explore the impact of several potential improvements, including fast proton heating, alpha power capture, direct conversion, and efficient heating. We find that such improvements could reduce the required Lawson product by a further order of magnitude, bringing aneutronic fusion to target ITER ion densities and confinement times.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Total Cost of Ownership Reduction Using Passive Pre-Chamber Ignition in Natural Gas Engines

Spark plug durability is a factor affecting the total cost of ownership (TCO) of spark-ignited natural gas engines, with some heavy-duty platforms requiring plug replacement after only 750 hours of operation. The high ignition energy demand under lean or diluted conditions accelerates electrode wear, shortening plug life and increasing maintenance frequency. This work evaluates passive pre-chamber (PC) ignition operating at lowered spark energies as a strategy to reduce spark energy requirements and extend plug durability, thereby lowering TCO. Experiments were conducted on a medium-duty Cummins 6.7L ISB engine at 1600 RPM and 50% load under varying exhaust gas recirculation (EGR) dilution levels (0–40%). Two passive pre-chambers with 1.1 mm and 1.6 mm nozzle diameters were compared with conventional spark ignition (SI). SI was operated with a fixed coil dwell of 4 ms (~90 mJ), while the PC configuration was tested across 2–4 ms dwell times (~30–90 mJ). Cylinder pressure analysis revealed that PC ignition sustained stable combustion at significantly lower spark energies than SI, with improved combustion stability at ~30 mJ compared with SI at ~90 mJ. The PC system also extended the dilution tolerance beyond that achievable with SI, while delivering up to ~2% higher indicated thermal efficiency and reducing the COV by nearly 90% at 30% EGR. A TCO analysis was conducted to assess the economic benefit of adopting a passive PC system operating at reduced spark energies compared to SI. It was found that adopting a passive PC system could reduce TCO by approximately $11,000 per engine over a five-year operational period, primarily due to fuel savings, extended spark plug life, and reduced maintenance frequency. These projections were weighed against the additional hardware cost of the pre-chamber, yielding a rapid estimated return on investment of ~300 operating hours. Therefore, this work motivates continued research and development of passive PC technology and its commercial adoption in natural gas engines used in transportation applications.

Dhotre, Akash [University of Minnesota]↗
DOE OSTI2022

Spark-Assisted HCCI Residential CHP

A transformative small spark ignition (SI) internal combustion (IC) engine fueled with natural gas was developed for combined heat and power (CHP) applications using a combination of cycle simulations, computational fluid dynamics (CFD) modeling, and engine experiments. The resulting 1 kW CHP engine was demonstrated to achieve 36.1% brake thermal efficiency (BTE) while meeting aggressive exhaust emissions targets using a low-cost three-way catalyst. Starting from a “clean-sheet” design, modeling tools were used to select the optimal engine parameters and operating characteristics. The disruptive technologies developed for the CHP system have a target lifetime of at least 10 years. The engine cost at volume of 10,000 units was estimated to be $\$$1,050. A combination of experimental and simulation results were used to identify a path to the program target of 38.6% BTE. Base engine design parameters (i.e., displacement, speed, bore, stroke, valve timings, and compression ratio) were optimized to reduce friction, heat transfer, and exhaust losses. The base clean sheet prototype engine achieved 32% BTE. Optimization of the lube oil and coolant temperatures added 1.8% BTE. The addition of exhaust gas recirculation added 1.1% BTE. Novel thermal barrier coatings (TBCs) developed over the course of the project added 1.2% BTE. Further improvements in engine friction reduction (1.3% BTE) and improved combustion (1.2% BTE) are estimated to meet the program target 38.6% BTE, while also meeting the stringent criteria pollutant emissions targets.

42 ENGINEERING↗
DOE OSTI2023

Editorial: Using high energy density plasmas for nuclear experiments relevant to nuclear astrophysics

Thermonuclear reaction rates and nuclear processes have traditionally been explored by means of accelerator experiments, which are difficult to execute at conditions relevant to nucleosynthesis. High energy density (HED) plasmas generated using lasers, such as the inertial confinement fusion (ICF) platform, more closely mimic astrophysical environments in several ways, including with thermal distributions of reacting ions as opposed to mono-energetic ions impinging on a cold target; stellar-relevant plasma temperatures and densities; and neutron flux densities not found anywhere else on earth. The most extreme conditions can currently be achieved at the National Ignition Facility (NIF) laser in the US, where densities of 10 3 g/cm 3 and neutron fluxes up to 5∙10 27 neutrons/cm/s have been demonstrated over a time period of a few tens of picoseconds. The HED platform is emerging as an interesting complement to accelerator experiments.

charged-particle-induced reactions↗
DOE OSTI2020

Plasma Electrolytic Oxidation (PEO) Coatings as Superior Thermal Barriers for Engine Pistons. Final Report

Thermal barrier coatings (TBCs) have received considerable interest in internal combustion engines, as a means to increase overall efficiency. However, despite some promising results for coatings with adequate thermal properties, durability has remained a barrier to commercialization, which has damped interest from automotive manufacturers. The PEO-based TBC developed by IBC Materials has exceptional durability, and thermal properties comparable or superior to state of the art. In this Phase I effort, IBC has demonstrated this durability by coating pistons from a current production engine (Kohler KD440) and conducting thermal shock testing on several coated pistons. Following successful thermal shock testing, a piston was run in this engine for an extended period(>120h) and showed no evidence of damage to the piston coating or engine bore. The PEO-based TBC also increased heat rejection from the combustion chamber, resulting in significantly increased exhaust temperature. Operation of the engine with PEO-based TBCs was also found to delay the onset of fuel ignition, possibly due to reduced heat retention by the piston. After slightly modifying the engine operation to counteract this effect, a modest improvement (+0.8%) to overall efficiency was achieved. With additional tuning of coating parameters and combustion timing, it is very likely that additional gains can be realized. This result also points to the possibility of future designs which require less capacity from the cooling system (e.g. a radiator), which draws energy and adds mass and complexity to an overall powertrain.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Time Shifted Transport Tallies

When modeling experiments on platforms such as the National Ignition Facility (NIF), several different calculations are strung together to calculate the final diagnostic response of the detectors on the machine. For example, a highly detailed simulation may be performed of capsule implosion on NIF, where one of the key diagnostics is the history of the thermal radiation emission from the capsule. This simulation domain can be a few centimeters in size. The NIF target chamber is much larger, so a second calculation can be done to transport the energy from the capsule out to the diagnostics. Typically, the results from the first calculation are used as a point source in the second, since all the fine detail is not needed.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

High Inlet Temperature Combustor for Direct-Fired Supercritical Oxy-Combustion

It is envisioned that supercritical CO 2 (sCO 2 ) electric power plant efficiencies can exceed 52% with 99% carbon capture using direct-fired oxy-combustion. Such efficiencies would be competitive with Natural Gas Combined Cycles (NGCC) and operate with nearly zero carbon emissions. To achieve high plant efficiencies, turbine inlet conditions must approach 1,200 °C at 250 bar. Such conditions, while desirable from a systems perspective, exceed the current state of the art in turbine design and materials qualification. The team of Southwest Research Institute ® (SwRI ® ), Georgia Institute of Technology (Georgia Tech), Spectral Energies, LLC (Spectral), GE Global Research (GE-GRC), and the University of Central Florida (UCF) sought to demonstrate an intermediate step toward these high efficiency plants with the development of a 1 MWth, subscale direct-fired oxy-fuel combustor. The efforts focused largely on the development of an auto-ignition based combustion system capable of providing the targeted 1200 °C and the pilot-scale plant to operate the combustor. While the project was stopped short of the commissioning and demonstration work, the advances made in this effort will reduce risks associated with chemical kinetics, thermal management, water separation, flue gas cleanup, materials selection, and corrosion in future demonstration efforts for the direct-fired oxy-fuel combustion cycles. The following report documents the design, analysis, and installation efforts completed during the project periods of performance.

03 NATURAL GAS↗
DOE OSTI2022

Novel method to control explosive shock sensitivity: A mesoscale study to understand the effect of thermally expandable microsphere (TEM) inclusions in high explosives (HE) microstructure

When the void content and/or void structure of a high explosive (HE) is altered by some means (i.e., bulk heating or mechanical damage), the shock initiation behavior of the material changes. The ability to precisely predict the change in shock sensitivity after an HE has undergone microstructural changes is a crucial capability in multi-scale reactive flow models. Here, we utilize thermally expandable microspheres (TEMs) as a dopant in a polymer bonded explosive (PBX) matrix to alter the shock initiation properties in a controlled fashion. Here, using a mesoscale modeling approach, we evaluated how a single TEM (before and after thermal expansion) behaves under shock compression, as well as how the matrix PBX in the direct vicinity of the TEM is affected. We first examined the effect of an unexpanded TEM in the explosive matrix and found that its presence does not significantly perturb the bulk flow and by extension will not affect bulk sensitivity. Next, we examined the effect of an expanded TEM and found that its presence significantly perturbs the flow via hydrodynamic jetting, which causes a secondary shock wave with a strength that exceeds that of the incident wave. Finally, we showed that this secondary shock interacts with the downstream porosity to ignite a larger fraction of the overall pore volume, commensurate with the secondary shock strength and the affected volume, increasing the global (bulk) shock sensitivity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Unraveling electronic correlations in warm dense quantum plasmas

The study of matter at extreme densities and temperatures has emerged as a highly active frontier at the interface of plasma physics, material science and quantum chemistry with relevance for planetary modeling and inertial confinement fusion. A particular feature of such warm dense matter is the complex interplay of Coulomb interactions, quantum effects, and thermal excitations, making its rigorous theoretical description challenging. Here, we demonstrate how ab initio path integral Monte Carlo simulations allow us to unravel this intricate interplay for the example of strongly compressed beryllium, focusing on two X-ray Thomson scattering data sets obtained at the National Ignition Facility. We find excellent agreement between simulation and experiment with a very high level of consistency between independent observations without the need for any empirical input parameters. Our results call into question previously used chemical models, with important implications for the interpretation of scattering experiments and radiation hydrodynamics simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Direct-drive double-shell implosion: A platform for burning-plasma physics studies

Double-shell ignition designs have been investigated with the indirect-drive inertial confinement fusion (ICF) scheme in both simulations and experiments in which the inner-shell kinetic energy was limited to ~10 to 15 kJ, even driven by megajoule-class lasers such as the National Ignition Facility. Since direct-drive ICF can couple more energy to the imploding shells, we have performed a detailed study on direct-drive double-shell (D 3 S) implosions with state-of-the-art physics models implemented in radiation-hydrodynamic codes (LILAC and DRACO), including nonlocal thermal transport, cross-beam energy transfer (CBET), and first-principles-based material properties. To mitigate classical unstable interfaces, we have proposed the use of a tungsten/beryllium–mixed inner shell with gradient-density layers that can be made by magnetron sputtering. In our D 3 S designs, a 70-μm-thick beryllium outer shell is driven symmetrically by a high-adiabat (α ≥ 10), 1.9-MJ laser pulse to a peak velocity of ~240 km/s. Upon spherical impact, the outer shell transfers ~30 to 40 kJ of kinetic energy to the inner shell filled with deuterium–tritium gas or liquid, giving neutron-yield energies of ~6 MJ in 1-D simulations. Two-dimensional high-mode DRACO simulations indicated that such high-adiabat D 3 S implosions are not susceptible to laser imprint, but the long-wavelength perturbations from the laser port configuration along with CBET can be detrimental to the target performance. Yet, neutron yields of ~0.3- to 1.0-MJ energies can still be obtained from our high-mode DRACO simulations. The robust α-particle bootstrap is readily reached, which could provide a viable platform for burning-plasma physics studies. Once CBET mitigation and/or more laser energy becomes available, we believe that breakeven or moderate energy gain might be feasible with the proposed D 3 S scheme.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Nebular Models of Sub-Chandrasekhar Mass Type Ia Supernovae: Clues to the Origin of Ca-rich Transients

In this work we use non-local thermal equilibrium radiative transport modeling to examine observational signatures of sub-Chandrasekhar mass double detonation explosions in the nebular phase. Results range from spectra that look like typical and subluminous Type Ia supernovae (SNe) for higher mass progenitors to spectra that look like Ca-rich transients for lower mass progenitors. This ignition mechanism produces an inherent relationship between emission features and the progenitor mass as the ratio of the nebular [Ca II ]/[Fe III ] emission lines increases with decreasing white dwarf mass. Examining the [Ca II ]/[Fe III ] nebular line ratio in a sample of observed SNe we find further evidence for the two distinct classes of SNe Ia identified in Polin et al. by their relationship between Si ii velocity and B-band magnitude, both at time of peak brightness. This suggests that SNe Ia arise from more than one progenitor channel, and provides an empirical method for classifying events based on their physical origin. Furthermore, we provide insight to the mysterious origin of Ca-rich transients. Low-mass double detonation models with only a small mass fraction of Ca (1%) produce nebular spectra that cool primarily through forbidden [Ca II ] emission.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Development of a medium-duty stoichiometric diesel micro-pilot natural gas engine

Fueling a compression-ignition engine with premixed natural gas offers the potential to combine a clean-burning, low-carbon fuel with a high compression ratio, high-efficiency engine. This work describes the development of a multi-cylinder 6.7 L diesel engine converted to run stoichiometric diesel micro-pilot/ natural gas premix combustion with a maximum diesel contribution target of 5% of the total fuel energy and a three-way catalyst aftertreatment system. Results are given by comparing the stoichiometric combustion to the diesel baseline operation, showing combustion characteristics differences, including the rapid two stage heat release. A high load output of 23 bar brake mean effective pressure was obtained with diesel-like brake thermal efficiency of 41%. This operating condition enabled a brake specific CO 2 emissions reduction of up to 25% when compared to diesel. It was observed that the low load output is limited by combustion stability when operated at stoichiometric condition. The three-way catalyst is observed to run at peak efficiency with an equivalence ratio of 1.01. Injector fouling was observed through the inspection of the nozzle and its internal parts, indicating carbon build-up similar to that seen in injector coking mechanisms. A comparison of the developed engine to other engine technologies is given, showing that the diesel micro-pilot natural gas engine performance is in good standing among other diesel and gas engines in the market.

Engineering↗
DOE OSTI2023

Wet biofuel compression ignition

A compression ignition engine system allows use of hydrous fuels, in particular hydrous biofuels, with high water content (e.g., 20-85% water). The hydrous fuel is pressurized, and also preferably heated via the engine's exhaust gas, to increase its enthalpy, and is then directly injected into the engine cylinder(s) near top dead center. The system provides brake thermal efficiency increases of 20% or more versus a comparable system using conventional diesel fuel, while allowing the use of inexpensive undistilled or lightly distilled biofuels.

Wickman, David Darin↗
DOE OSTI2024

Numerical modeling of plasma assisted deflagration to detonation transition in a microscale channel

Here, this work numerically studies the plasma assisted deflagration to detonation transition (DDT) of H 2 /O 2 mixtures in a microscale channel with detailed chemistry and transport. The results show that the DDT onset time is non-monotonically dependent on the discharge pulse number. The DDT is accelerated with small pulse numbers, whereas retarded with large ones. Two different DDT regimes, respectively at a small and large plasma discharge number, via acoustic choking of the burned gas and plasma-enhanced reactivity gradient without acoustic choking, are observed. Without plasma discharge, pronounced pressure and temperature gradients in front of the flame are generated by acoustic compression after the choking of the burned gas, triggering DDT via autoignition. With small plasma pulse numbers, the plasma-generated species enhance the ignition kinetics and lead to an increased reactivity in the boundary layer. After the choking of the burned gas, the plasma-enhanced reactivity advances the sequence of autoignition near the wall, strengthens ignition-shock wave coupling, and accelerates DDT. However, with a large discharge pulse number, a direct autoignition initiating DDT can occur without the acoustic choking of the burned gas due to the strongly accelerated reactivity and elevated temperature. In this case, DDT onset is retarded because the elevated temperature increases sonic velocity and the increased reactivity accelerates fuel oxidation in front of the flame, decelerating the formation of a leading shock and subsequent pressure buildup ahead of the flame. The present modeling reveals that no matter with or without plasma discharge, DDT is initiated by autoignition in thermal, pressure, and reactivity gradient fields via the Zel'dovich gradient mechanism. The acoustic choking of the burned gas may not be the necessary condition of DDT with strong plasma-enhanced reactivity gradient. This work provides an answer to the experimentally observed non-monotonic DDT onset time by plasma, which provides guidance to control DDT in advanced detonation engines and fire safety of hydrogen-fueled catalytic reactors in microchannels by non-equilibrium plasma discharge.

33 ADVANCED PROPULSION SYSTEMS↗