Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermomechanical Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Step-loaded creep testing of Zircaloy-4 cladding at higher temperatures in the α-phase

A refined understanding of zirconium-based cladding thermomechanical performance during rapid transients is essential for enhancing the safety and operation of light-water reactors. Traditional models for zirconium alloys under accident conditions generally assume that creep dominates fuel cladding performance. Here, these historic models have largely remained unchanged and serve as the basis for safety criteria development. As the U.S. nuclear industry pursues higher burnup levels, the increased release of fission gases during transients raises the risk of cladding failure in the low-temperature hcp α-phase, making the fidelity of these models of greater importance. Creep testing was conducted from 550–700°C with 25–120 MPa applied hoop stresses to investigate Zircaloy-4 deformation at accident-relevant temperatures in the α-phase. Step-loading was employed to capture creep behavior across a wide stress range from a single sample. The stress-strain rate data at higher temperatures (650 and 700°C) were well-described by isotropic versions of the Erbacher and Kaddour models, while the lower temperature data (550 and 600°C) were underpredicted by both anisotropic and isotropic model variants. Greater strain rates during the initial loading step at 650 and 700°C were attributed to recrystallization and grain growth of sub-micron crystallites. Yet, texture analysis revealed the basal split texture remained after testing. These observations produced results suggesting Zircaloy-4 claddings experience higher creep rates across the α-phase than previously thought, possibly related to dynamic anisotropy due to temperature dependent activation of deformation mechanisms, effects of biaxial loading, and variation in material condition between the current testing used in previous model development.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Design, fabrication, and testing of a water-cooled tungsten-foam high-heat flux plasma-facing module

Here, we present a comprehensive study detailing the design, fabrication and testing a new modular “finger” component, featuring a hexagonal tungsten foam armor tile bonded to the top surface of the water-cooled finger unit. The mechanical, thermal, and particle transport properties of the tungsten foam armor were determined for a wide range of porosity and cell size, and then combined in an equivalent solid material with “effective” properties suitable for large-scale simulations. A series of 3-D multiphysics simulations for coupled thermal and mechanical behavior of the “finger” module are used to optimize the design before fabrication. The simulation results show that, for the expected experimental conditions, a safe range of heat flux and foam porosity is possible for both water-cooling and helium-cooling. Based on these multiphysics simulations, an optimum finger cooling module has been fabricated at Ultramet, Inc. A series of experiments were designed to study the thermomechanical performance of the “finger” unit under steady-state and transient thermal loading at surface heat flux up to 16 MW/m 2 in the High Energy Flux Test facility (HEFTY) at UCLA. Testing conditions included low-power, steady-state plasma exposure at 6 MW/m 2 , followed by severe high heat flux cycles at 16 MW/m 2 . Results of these tests are explained through comparisons with multiphysics simulations. To eliminate the effects of thermomechanical damage carried out on a module on its thermo-mechanical response on a subsequent test, three different yet identically designed and fabricated finger modules were tested. The results show that the current design is capable of cooling the walls of fusion devices at surface heat flux up to 6 MW/m 2 without failure, and that the failure heat flux limit is below 16 MW/m 2 .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1984

Creep fatigue life prediction for engine hot section materials (isotropic): Two year update

Requirements for increased durability of gas turbine hot section components have placed a greater degree of importance on accurate structural analysis and life prediction. Various life prediction approaches for high temperature applications were investigated. Basic models were selected and developed for simple-cycle, isothermal loading conditions. Models will be developed which address thermomechanical cycling, multiaxial conditions, cumulative loading, environmental effects, and cyclic mean stress. Verification tests of models will be conducted on an alternate material and coating system.

Moreno, V.↗
DOE OSTI2025

AGR TRISO Fuel Performance Modeling in FY-25

This report summarizes the activities performed in FY-25 to support fuel performance modeling for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. This includes implementation of a new uranium oxycarbide (UCO) kernel swelling rate model, inner pyrolytic carbon (IPyC) cracking behavior and failure predictions, development of new UCO and silicon carbide (SiC) cesium diffusion parameters, and the thermomechanical behavior of particle layers using experimental data from micro-tensile strength testing.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1985

Thermal barrier coating life prediction model development

A methodology was established to predict thermal barrier coating life in an environment simulative of that experienced by gas turbine airfoils. Specifically, work is being conducted to determine failure modes of thermal barrier coatings in the aircraft engine environment. Analytical studies coupled with appropriate physical and mechanical property determinations are being employed to derive coating life prediction model(s) on the important failure mode(s). An initial review of experimental and flight service components indicates that the predominant mode of TBC failure involves thermomechanical spallation of the ceramic coating layer. This ceramic spallation involves the formation of a dominant crack in the ceramic coating parallel to and closely adjacent to the metal-ceramic interface. Initial results from a laboratory test program designed to study the influence of various driving forces such as temperature, thermal cycle frequency, environment, and coating thickness, on ceramic coating spalling life suggest that bond coat oxidation damage at the metal-ceramic interface contributes significantly to thermomechanical cracking in the ceramic layer. Low cycle rate furnace testing in air and in argon clearly shows a dramatic increase of spalling life in the non-oxidizing environments.

Sheffler, K. D.↗
NASA NTRS1995

Materials research for high-speed civil transport and generic hypersonics: Composites durability

This report covers a portion of an ongoing investigation of the durability of composites for the High Speed Civil Transport (HSCT) program. Candidate HSCT composites need to possess the high-temperature capability required for supersonic flight. This program was designed to initiate the design, analysis, fabrication, and testing of equipment intended for use in validating the long-term durability of materials for the HSCT. This equipment includes thermally actuated compression and tension fixtures, hydraulic-actuated reversible load fixtures, and thermal chambers. This equipment can be used for the durability evaluation of both composite and adhesive materials. Thermally actuated fixtures are recommended for fatigue cycling when long-term thermomechanical fatigue (TMF) data are required on coupon-sized tension or compression specimens. Long term durability testing plans for polymer matrix composite specimens are included.

Allen-Lilly, Heather↗
NASA NTRSDate not supplied

High-Temperature Mechanical Tensile Testing of Unidirectional Sic/Sic Composites Using A Versatile Lamp Furnace

Silicon carbide (SiC) based ceramic matrix composites (CMCs) are of interest for high-temperature structural applications, including use in turbine engine components. To understand damage mechanisms and predict durability of these systems, in-depth knowledge of their behavior at ambient and high temperatures is necessary. A method for high temperature testing of SiC/SiC minicomposite specimens up to 1500oC in both tensile fast fracture and creep conditions to investigate their thermomechanical behavior will be presented. This method utilizes a novel radiation heat furnace, equipped with infrared lamps with ellipsoidal reflectors, to heat the specimen at the furnace center in user-defined atmospheres. The housing structure of the lamps allows for observation of the specimen during testing using optical methods and for conducting other experimental studies. The goal is to employ nondestructive health monitoring techniques in-situ, including acoustic emission (AE), electrical resistance (ER), and digital image correlation (DIC) to evaluate damage initiation and evolution in the minicomposite specimens during tensile testing. Results from mechanical testing and nondestructive techniques will be presented. Electron microscopy and X-ray micro-computed tomography were used to further characterize specimen damage after testing.

Aeronautics↗
DOE OSTI2025

Recrystallization driven softening and heating rate dependencies of FeCrAl nuclear fuel cladding during accident transients

A refined understanding of FeCrAl cladding behavior during rapid transients is critical for its potential deployment in light-water reactors. Current assessments focus on transient burst testing metrics such as balloon geometry, burst temperature, and hoop stress, often used as proxies for simpler conventional tensile properties. However, directly correlating isothermal tensile and creep data with accident transient scenarios remains a challenge, although it is essential for high fidelity model development. Recent modeling based on tensile tests up to 800 °C, conducted with both immediate loading and a 10-minute soak, showed that immediate loading better predicts experimental burst temperatures, indicating a thermal softening effect. Building upon this observation, the current study connects transient performance, microstructural evolution, and high-temperature tensile properties by leveraging results from C26M claddings burst tests performed at heating rates of 1–50 °C/s and hoop stresses from 25 to 100 MPa. At 25 MPa, rupture temperatures varied by only 6 °C, but at 100 MPa, the difference reached 116 °C, with faster heating yielding higher burst temperatures. Microstructural analysis identified recrystallization as the primary cause of heating rate-dependent softening, eliminating prior cold-working. In-situ thermomechanical data linked ballooning onset to localized instabilities, similar to ultimate tensile strength behavior in conventional tensile tests. High heating rates correlated with immediate loading tensile data, while lower rates matched soaked data. Furthermore, by linking burst performance to microstructural evolution and tensile properties, this work provides a foundation for more accurate modeling of FeCrAl claddings and potentially other Fe-based materials under accident conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Neutron irradiation & thermomechanical experiment (NITE) - design

For the reliable long-term operation of fusion power plants, it is crucial to understand and predict the lifetime of materials in use. These materials include all structural and functional materials utilized at the first wall, blanket, magnets, and shielding. The key challenge is, that the harsh environment including high heat fluxes, high thermal stress and stress cycling, neutron irradiation, and sputtering on such materials should not be viewed separately. Currently, the synergistic loads cannot be evaluated experimentally because of the lack of adequate facilities. The purpose of that work is to design a synergetic Neutron Irradiation and Thermomechanical Experiment (NITE) for fusion materials. This design will leverage the existing Advanced-Test-Reactor (ATR), a fission reactor at the Idaho National Laboratory. We also acknowledge that with existing fission reactors the exact fusion condition cannot be created, and the limitations are critically discussed. The combination of neutron irradiation with a high heat flux is the focus. This is realized with an irradiation capsule design that includes a TRISO fueled region inside the capsule to enable a steady-state heat flux on one side of the specimen. In conclusion, the experimental design modeling showed that steady-state heat fluxes of 2.4 MW/m 2 with a thermal gradient of above 250°C can be achieved in a 5 mm thick specimen.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Parametric Design Study of a Power Electronics Package for Improving Solder Joint Reliability

The lifetime of a power electronics package is, to a large extent, determined by the reliability of its bonded interfaces under major loading conditions in an operational environment. Based on the application-level requirements of the package, bonded interface material is selected based on the results obtained from accelerated tests such as thermal cycling and power cycling. In addition to evaluating the reliability through accelerated tests, it is important to consider the impact of other component layers on the thermomechanical performance of the interface material, both from a material and geometric perspective. The co-efficient of thermal expansion (CTE) mismatch introduced by the use of different materials within a package and its structural design plays a critical role in determining the interface material reliability. In this paper, we present the results of a parametric modeling study of a power electronics package under thermal cycling in which the materials and geometric design of the different component layers were varied with respect to a baseline design to understand their impact on the reliability of the interface material. We chose the volume-averaged strain energy density per cycle computed at the corner region of the interface material as the metric for the reliability comparisons. Our results indicate that in addition to the CTE mismatch, the stiffness of individual component layers has a major impact on reliability. Among the different baseplates that we studied, aluminum silicon-carbide baseplates offered superior reliability over their copper and aluminum counterparts. We also found that the magnitude of the impact of stiffness variation—amongst the adjacent layers—on the reliability of the solder joint is dependent on the inherent CTE mismatch between the layers.

47 OTHER INSTRUMENTATION↗
NASA NTRS1981

Effects of static tensile load on the thermal expansion of Gr/PI composite material

The effect of static tensile load on the thermal expansion of Gr/PI composite material was measured for seven different laminate configurations. A computer program was developed which implements laminate theory in a piecewise linear fashion to predict the coupled nonlinear thermomechanical behavior. Static tensile load significantly affected the thermal expansion characteristics of the laminates tested. This effect is attributed to a fiber instability micromechanical behavior of the constituent materials. Analytical results correlated reasonably well with free thermal expansion tests (no load applied to the specimen). However, correlation was poor for tests with an applied load.

Farley, G. L.↗
NASA NTRS2005

Investigation of the Thermomechanical Response of Shape Memory Alloy Hybrid Composite Beams

Previous work at NASA Langley Research Center (LaRC) involved fabrication and testing of composite beams with embedded, pre-strained shape memory alloy (SMA) ribbons. That study also provided comparison of experimental results with numerical predictions from a research code making use of a new thermoelastic model for shape memory alloy hybrid composite (SMAHC) structures. The previous work showed qualitative validation of the numerical model. However, deficiencies in the experimental-numerical correlation were noted and hypotheses for the discrepancies were given for further investigation. The goal of this work is to refine the experimental measurement and numerical modeling approaches in order to better understand the discrepancies, improve the correlation between prediction and measurement, and provide rigorous quantitative validation of the numerical model. Thermal buckling, post-buckling, and random responses to thermal and inertial (base acceleration) loads are studied. Excellent agreement is achieved between the predicted and measured results, thereby quantitatively validating the numerical tool.

Davis, Brian A.↗
DOE OSTI2020

Parametric Design Study of a Power Electronics Package

The lifetime of a power electronics package is, to a large extent, determined by the reliability of its bonded interfaces under major loading conditions in an operational environment. Based on the application-level requirements of the package, bonded interface material is selected based on the results obtained from accelerated tests such as thermal cycling and power cycling. In addition to evaluating the reliability through accelerated tests, it is important to consider the impact of other component layers on the thermomechanical performance of the interface material, both from a material and geometric perspective. The co-efficient of thermal expansion (CTE) mismatch introduced by the use of different materials within a package and its structural design plays a critical role in determining the interface material reliability. In this paper, we present the results of a parametric modeling study of a power electronics package under thermal cycling in which the materials and geometric design of the different component layers were varied with respect to a baseline design to understand their impact on the reliability of the interface material. We chose the volume-averaged strain energy density per cycle computed at the corner region of the interface material as the metric for the reliability comparisons. Our results indicate that in addition to the CTE mismatch, the stiffness of individual component layers has a major impact on reliability. Among the different baseplates that we studied, aluminum silicon-carbide baseplates offered superior reliability over their copper and aluminum counterparts. We also found that the magnitude of the impact of stiffness variation—amongst the adjacent layers—on the reliability of the solder joint is dependent on the inherent CTE mismatch between the layers.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Implement and Test 3D Mortar Contact in BISON

We leverage the extension of the generation of mortar segment meshes to three dimensions in MOOSE’s framework to extend thermomechanical modeling capabilities to problems with three dimensions. A modular approach to gap heat transfer physics using the mortar finite element method was created and documented, mechanical contact was extended to three dimensions—including frictional behavior, performance and ease of use were improved, and steps towards scalability of solid mechanics problems involving contact were taken. Many of these new developments are demonstrated in the simulation of 3D light-water reactor (LWR) problems, where the thermomechanical interface problem is solved using the mortar finite element method. Usage of the mortar framework has improved convergence in 2D problems and has enabled employing friction in 3D problems, of which we show results of a short, local stack of 3D pellets. Consequently, the benefits of mortar in terms of solution convergence and quality are extended to three dimensions. Section 2 discusses fundamental developments that enabled the simulation of practical mortar problems in three dimensions and other general improvements, including the reduction of the derivative container size, the modification of dual basis computations when edge dropping (lack of secondary element projection) takes place, the improvement of conditioning when employing the VCP in-edge dropping conditions, and code usability and quality improvements. These latter code enhancements include the migration of tests using “old” mortar contact constraints to using dual mortar with a semi-smooth Newton solution strategy and the reuse of lower dimensional domains for straightforwardly setting up a mortar thermomechanical LWR problem, i.e. the MOOSE action is employed for mechanical contact and the thermal LWR action is employed to capture the gas conductance, contact, and radiation components of gap heat transfer physics. Independently of the mortar LWR thermal action, we developed a modular approach to gap heat transfer that resides in MOOSE and can be leveraged, e.g., in metallic fuel problems. This approach, whose code design based on MOOSE’s user objects to model specific physics was proposed by the maintenance activity, is detailed in Section 3. Based on the dual mortar finite element method, the frictional contact constraints were extended to three dimensions. A block sheared in two directions in and out of contact with a rigid plane is employed in Section 4 to show the way the approach handles changes in frictional states (e.g. stick to slip) within a competitive number of Newton iterations. Equations and numerical results on the use of the VCP with Cartesian Lagrange multipliers, whose combination enables their direct condensation, are described in Section 5.3. Two-dimensional and three-dimensional BISON LWR simulations are discussed in Section 6. Particularly, a stack of five eccentric pellets with a surface defect is simulated and the effect of pellet-cladding friction is assessed. Finally, conclusions are outlined in Section 7.

42 ENGINEERING↗
DOE OSTI2022

Ordered Particle Packing in Dense TRISO/SiC Fuel Elements and Preliminary Assessment of Neutronic and Thermomechanical Characteristics

Detailed analysis of the particle distribution in Transformational Challenge Reactor fuel elements indicates that particle packing is not random; instead, it follows a relatively ordered structure near fuel element surfaces. Discrete particle neutronic simulations indicate that the core reactivity is not impacted when assuming homogenization of particles with the silicon carbide matrix. However, the neutronic power distribution resulting from the ordered packing structure indicates that the highest-power particles reside at the top and bottom of the fuel elements and nearest the YH 1.85 moderator rods. The power distribution results were applied to thermo-mechanical simulations using mesh-based power distributions. Previous results indicated high stress at the bottom of the fuel element, where packing is most ordered. Additionally, to reduce this stress concentration, additively manufactured protrusions were added to the bottom of a test fuel element to disrupt dense particle packing. These protrusions reduced the overall power peaking, but the thermomechanical simulations did not indicate a significant change in the fuel element’s maximum stress or failure probability.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Development of Additive Manufacturing for Ceramic Matrix Composite Vanes

This report discusses the development of additive manufacturing for polymer-derived ceramic materials to create novel cooled gas turbine airfoils made from ceramics. Gas turbine engines have extremely high temperatures in the hot section of the engine that exceed the melting point of nickel superalloy materials that the engine is made from. Advanced cooling technologies have been developed over decades for metallic parts. Ceramic materials have higher temperature capabilities than superalloys, but are difficult to shape in the complex designs used in modern turbines. Several thrusts were investigated during the project, including development of higher material strength resins, improvement of ultraviolet (UV) photopolymerization and post-processing techniques to increase survivability of ceramic parts, thermomechanical modeling of novel ceramic airfoil designs for higher cooling effectiveness, and experimental validation of the modeling and manufacturing in a turbine vane test facility at nondimensional conditions that are relevant to modern gas turbines. Some major findings of the work include a significant increase in ceramic survivability during pyrolysis (a high temperature process that converts the organic material to a ceramic) by adjusting the composition ratios of the resins, as well as a tolulene soak after printing to remove unreacted polymer material. Thermomechanical optimization of the internal cooling structure indicated that a high density pin fin array would enable an 80% increase in overall cooling effectiveness relative to a baseline geometry, which was later verified during experimental testing in a high speed linear cascade. Ceramic vanes were tested at Mach numbers of up to 0.9 which is relevant to modern gas turbines. High temperature capability of the ceramic vanes was not tested in this work.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Stereomicrostructure-regulated biodegradable adhesives

Commercial adhesives are petroleum-based thermoset networks or nonbiodegradable thermoplastic hot melts, making them ideal targets for replacement by biodegradable alternatives. Poly(3-hydroxybutyrate) (P3HB) is a biorenewable and biodegradable alternative to conventional plastics, but microbial P3HB, which has a stereoperfect stereomicrostructure, exhibits no adhesion. Here, in this study, by elucidating the fundamental relationship between chemocatalytically engineered P3HB stereomicrostructures and adhesion properties, we found that biodegradable syndio-rich P3HB exhibits high adhesion strength and outperforms common commercial adhesives, whereas syndiotactic, isotactic, or iso-rich P3HB shows no measurable adhesion. The syndio-rich stereomicrostructure brings about desired thermomechanical and viscoelastic properties of P3HB that enable strong adhesion to a range of substrates tested, including aluminum, steel, glass, and wood, and its performance is insensitive to molar mass and reprocessing or reuse.

36 MATERIALS SCIENCE↗