Search NASA⌕ Search

SEARCH · Search NASA

Results for “Types Of Problems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

SLS Block-1B USA Separation Analysis and Requirements Evaluation Using the CLVTOPS Toolchain

Ensuring that rocket stage separation events provide positive clearance is critical to avoid loss of mission or crew. NASA's Marshall Space Flight Center (MSFC) has developed a cutting-edge toolchain to address this type of problem and it was used to set abstracted impulse requirements on, and to analyze the results of, the in-space separation event of the Universal Stage Adapter (USA) and the Exploration Upper Stage (EUS) of NASA's Space Launch System (SLS) Block-1B configuration. The toolchain is used as a hardware simulation to confirm positive body-to-body clearance during the separation event. It is also used to create a requirements-space simulation, which helps inform requirements as the hardware design matures.

Zach Muscha↗
NASA NTRS1989

On Bernstein type inequalities and a weighted Chebyshev approximation problem on ellipses

A classical inequality due to Bernstein which estimates the norm of polynomials on any given ellipse in terms of their norm on any smaller ellipse with the same foci is examined. For the uniform and a certain weighted uniform norm, and for the case that the two ellipses are not too close, sharp estimates of this type were derived and the corresponding extremal polynomials were determined. These Bernstein type inequalities are closely connected with certain constrained Chebyshev approximation problems on ellipses. Some new results were also presented for a weighted approximation problem of this type.

Freund, Roland↗
NASA NTRS1981

Application of constrained optimization to active control of aeroelastic response

Active control of aeroelastic response is a complex in which the designer usually tries to satisfy many criteria which are often conflicting. To further complicate the design problem, the state space equations describing this type of control problem are usually of high order, involving a large number of states to represent the flexible structure and unsteady aerodynamics. Control laws based on the standard Linear-Quadratic-Gaussian (LQG) method are of the same high order as the aeroelastic plant. To overcome this disadvantage of the LQG mode, an approach developed for designing low order optimal control laws which uses a nonlinear programming algorithm to search for the values of the control law variables that minimize a composite performance index, was extended to the constrained optimization problem. The method involves searching for the values of the control law variables that minimize a basic performance index while satisfying several inequality constraints that describe the design criteria. The method is applied to gust load alleviation of a drone aircraft.

Newsom, J. R.↗
NASA NTRS1987

Constrained optimization techniques for active control of aeroelastic response

Active control of aeroelastic response is a complex problem in which the designer usually tries to satisfy many design criteria which are often conflicting in nature. To further complicate the design problem, the state space equations describing this type of control problem are usually of high order, involving a large number of states to represent the flexible structure and unsteady aerodynamics. Control laws based on the standard Linear - Quadratic - Gaussian method are of the same high order as the aeroelastic plant and may be difficult to implement in the flight computer. To overcome this disadvantage a new approach was developed for designing low-order optimized robust control laws. In this approach, a nonlinear programming algorithm is used to search for the values of control law design variables that minimize a performance index while satisfying several inequality constraints that describe the design criteria on the stability robustness and responses. The method is applied to a gust load alleviation problem and a stability robustness improvement problem of a drone aircraft.

Mukhopadhyay, Vivekananda↗
NASA NTRS1972

An approach to the linear multivariable servomechanism problem.

This paper presents a state-space approach to the multivariable 'type one' servomechanism problem. Necessary and sufficient conditions for the controllability of such systems are derived and applied to the observability of the (dual) state reconstructor problem for a system with an unknown constant input. The paper also presents a simple systematic design algorithm which provides type one servomechanism performance to command inputs, together with pre-specified closed-loop pole locations. Examples are given to illustrate the utility of the design procedure.

Young, P. C.↗
NASA NTRS1987

A general method for dynamic analysis of structures overview

The presented research deals with the development of a dynamic analysis method for structural systems. The modeling approach is essentially a finite element method in the sense that the structure is divided into n elements. An element is defined as any structural unit whose degree of freedom (dofs) can be categorized as either interface or non-interface dofs. An element could be a fundamental unit such as a rod, a beam, a plate etc., or it could be an entire structural component. Furthermore, the parameters for the element could be distributed or lumped. The choice of elements is totally arbitrary and is a matter of user convenience. In particular, issues of accuracy and convergence do not enter on the level of example that bookkeeping is reduced to a minimum. Each element is modeled using a set of interface constraint modes (ICM) combined with a set of interface restrained normal models (IRNM). The next step is the solution of the system eigenvalue problem. The procedure calls for the sequential solution of a number of small eigenvalue problems based on a truncation principle for IRNM. In addition, the form of these eigenvalue problems is very simple such that an escalator type of eigenvalue problem solver can be used which is extremely cost-effective and fast.

Engels, Remi C.↗
NASA NTRS2016

Use of the NLP10x10 Sequential Quadratic Programming Algorithm To Solve Rotorcraft Hub Loads Minimisation Problems

Previous research and experimentation on the use of a non-linear programming constrained optimisation technique to define an optimal control vector for rotorcraft applications indicated that use of this methodology was feasible and desirable in many cases. In particular, use of non-linear programming methods that solve a sequence of related quadratic-programming sub-problems were used successfully to solve these problems. Accordingly, a licence for one of the latest versions of Professor Klaus Schittkowskis very successful Sequential Quadratic Programming NLPQLP software was obtained and used to experiment with and analyse typical optimisation problems of the type encountered in various rotorcraft wind tunnel and flight tests. This research resulted in the development of the general NLPQLP Computation System that could be used to solve problems of the type encountered in various rotorcraft applications where there is a linear dependence of the measurement vector on the control vector, and where equality andor inequality constraints might be imposed. This development was accomplished on a mainframe computer not part of actual wind tunnel andor flight-test experiment, but in a format which was transferable to wind tunnel lap-top computers. Emphasis was directed toward obtaining efficiency, robustness and speed in computation.The System was developed in support of the five-bladed SMART Rotor Active Flap Rotor Hub Loads analytical minimisation research. The design and development of the Computation System was tailored to address the particular requirements of the problem to minimise a performance metric function of measured hub load harmonic angular couple components by optimising the control vector harmonic flap angular couple components subject to constraints on the amplitudes of these control vector harmonic flap angular couple components. In addition, to facilitate real time wind tunnel experimentation, the ability to rapidly selectchange the particular hub load harmonic angular couple components andor the particular control vector harmonic angular couple components to be considered in the optimisation procedure was provided in the System. This capability allows the singling out of particular hub load frequencies andor particular flap angle frequencies to be analysed during testing operations. The System was used very successfully for the SMART Active Flap Rotor Hub minimisation problems considered in the study, the results of which were presented at the American Helicopter Society Fifth Decennial Aeromechanics Specialist Conference in January 2014. Excellent agreement between cases initiated with best guess starting estimates for the control vector elements and cases initiated with zero control vector starting element estimates resulted, indicating the robustness of the NLP10x10 algorithm.

Rotorcraft Hub Loads↗
NASA NTRS1988

On the constrained Chebyshev approximation problem on ellipses

Constrained Chebyshev approximation problems of the type with minimum (p is an element of Pi(sub n):p(c)=1) and maximum (z is an element of E) with /p(z)/ are considered. Here Pi(sub n) denotes the set of all complex polynomials of degree at most n, E is any ellipse in the complex plane, and c is an element of C/E. Such approximation problems arise in the context of optimizing semi-iterative methods for the solution of large, sparse systems of linear equations Ax=b with complex non-Hermitian coefficient matrices A. The problem of obtaining optimal polynomial preconditioners for conjugate gradient type methods for Ax=b also leads to problems of this type. A new family of polynomials -- q(sub n)(z;c), n is an element of N, and c is an element of C/E -- are introduced as the polynomials which are optimal for a modified version of the Chebyshev approximation problem with Pi(sub n) replaced by a certain subfamily. Some simple properties of q(sub n) are also listed. A necessary and sufficient condition for q(sub n) to be the extremal polynomial for the approximation problem is then derived. Finally, it is shown that q(sub n) is indeed optimal for the problem for all fixed n whenever the distance between c and E is sufficiently large. Results of some numerical tests are presented.

Freund, Roland↗
NASA NTRS1982

Examination of time series through randomly broken windows

The study of many astronomical problems involves a consideration of time series. The present investigation was prompted by a problem related to the determination of normal modes of oscillation of the sun. It is desirable to have an approach for obtaining an estimate of the accuracy with which oscillation modes may be determined when it appears possible to observe the sun over a long interval of time losing some blocks of time because of cloud cover. The present investigation has the objective to develop a model for addressing problems of this type. After presentation of a few general formulae, the problem is considerably simplified by supposing that observations are made over a large number N of equal time intervals, each of length t, so that the total time interval T is given by T = Nt. With certain additional simplifying assumptions, attention is given to the statistical properties of two functions which are representative of 'randomly broken' window functions.

Sturrock, P. A.↗
NASA NTRS2004

Early Design Choices: Capture, Model, Integrate, Analyze, Simulate

I. Designs are constructed incrementally to meet requirements and solve problems: a) Requirements types: objectives, scenarios, constraints, ilities. etc. b) Problem/issue types: risk/safety, cost/difficulty, interaction, conflict, etc. II. Capture requirements, problems and solutions: a) Collect design and analysis products and make them accessible for integration and analysis; b) Link changes in design requirements, problems and solutions; and c) Harvest design data for design models and choice structures. III. System designs are constructed by multiple groups designing interacting subsystems a) Diverse problems, choice criteria, analysis methods and point solutions. IV. Support integration and global analysis of repercussions: a) System implications of point solutions; b) Broad analysis of interactions beyond totals of mass, cost, etc.

Malin, Jane T.↗
NASA NTRS1990

New Bernstein type inequalities for polynomials on ellipses

New and sharp estimates are derived for the growth in the complex plane of polynomials known to have a curved majorant on a given ellipse. These so-called Bernstein type inequalities are closely connected with certain constrained Chebyshev approximation problems on ellipses. Also presented are some new results for approximation problems of this type.

Freund, Roland↗
NASA NTRS1961

A Flight Examination of Operating Problems of V/STOL Aircraft in STOL-Type Landing and Approach

A flight investigation has been conducted using a large twin-engine cargo aircraft to isolate the problems associated with operating propeller-driven aircraft in the STOL speed range where appreciable engine power is used to augment aerodynamic lift. The problems considered would also be representative of those of a large overloaded VTOL aircraft operating in an STOL manner with comparable thrust-to-weight ratios. The study showed that operation at low approach speeds was compromised by the necessity of maintaining high thrust to generate high lift and yet achieving the low lift-drag ratios needed for steep descents. The useable range of airspeed and flight path angle was limited by the pilot's demand for a positive climb margin at the approach speed, a suitable stall margin, and a control and/or performance margin for one engine inoperative. The optimum approach angle over an obstacle was found to be a compromise between obtaining the shortest air distance and the lowest touchdown velocity. In order to realize the greatest low-speed potential from STOL designs, the stability and control characteristics must be satisfactory.

Innis, Robert C.↗
NASA NTRS2000

Innovative Research Program: Supershields for Gamma-Ray Astronomy

The supershield project evaluated the importance of novel shield configurations for suppressing neutron induced background in new classes of gamma-ray detectors such as CZT. The basic concept was to use a two-part shield. The outer shield material heavily moderates the incoming neutron spectrum. This moderated neutron beam is then more easily absorbed by the inner material, which is an efficient neutron absorber. This approach is, in principle, more efficient than that in previous attempts to make neutron shields. These previous attempts involved biatomic, monlithic shields (eg. LiH) in which the shield consisted of a single material but with two types of atoms - one for moderating and one for absorbing. The problem with this type of monolithic shield is that moderating neutrons, without the efficient absorption of them, leads to the leakage into the detector of neutrons with a low energy component (approx. 10-100 KeV). These energy neutrons are particularly problematic for many types of detectors. The project was roughly divided into phases. In the first phase we attempted to carefully define the neutron source function incident on any space instrument. This is essential since the design of any shield depends on the shape of the incident neutron spectrum. We found that approximations commonly used in gamma-ray astronomy for photon background is inadequate. In addition, we found that secondary neutrons produced in any passive shield, and dominated by inelastic neutron scattering, are far more important than background due to neutron activation. The second phase of our work involved design of supershield geometries (one and three dimensional) in order to compare different shield configurations and materials for their effectiveness as neutron shields. Moreover we wanted to compare these supershields with previous neutron shields to confirm the performance differences between the supershield (two material) and monolithic (one material) designs and to understand the physics origins of these differences more clearly. The third phase of the supershield program involved the benchmarking of the supershield designs through direct experimental verification. This required fabricating various supershields and exposing them to beams of neutrons to directly characterize their performance. With explicit verification that our modeling procedures can be used with confidence, we are now in a position to design shields for realistic space geometries. Using the supershield modeling capacity developed as part of this program we are attempting to evaluate their utility for a specific proposed mission--the Energetic X-ray Imaging Survey Telescope (EXIST). It is anticipated that this experiment, which is limited by internal background at high energies, might benefit from a neutron shield.

Hailey, Charles J.↗
NASA NTRS1977

Small monopropellant thruster contamination measurement in a high-vacuum low-temperature facility

The contamination that results from the exhaust plume of small thrusters used for attitude control maneuvers can pose severe problems for long-life satellite systems. In order to assess this type of contamination problem, analytical and experimental techniques must be developed. Mass deposition rate measurements of a representative 0.44-N thrust hydrazine thruster were made in a space simulation chamber using five appropriately placed variable-temperature quartz crystal microbalances. The mass deposition rates within the thruster plume were measured while operating the thruster over a wide range of operating parameters, including duty cycles, catalyst bed start temperatures, propellant water variation, as well as thruster aging effects. The contamination measurements were made over a temperature range of 144 to 256 K for all duty cycles. In addition, the nominal duty cycle of 100 msec on and 10 sec off was run at a temperature of 106 K. These data will make possible better prediction of deposition rates of contaminants from thrusters used in satellite systems.

Passamaneck, R. S.↗
NASA NTRS1993

DESSY: Making a real-time expert system robust and useful

As the complexity and expected life-span of modern space systems continue to increase, the need for real-time data monitoring and failure analysis becomes more critical to their successful operation. The DEcision Support SYstem (DESSY) is a joint effort by the Intelligent Systems Branch/ER2 and the Remote Manipulator System (RMS) Section/DF44 to develop an expert system for the monitoring of the Payload Deployment and Retrieval System (PDRS). DESSY users, the RMS flight controllers, are provided with user interface enhancements and automated monitoring of system state (physical orientation) and status (operational health). Currently, a DESSY prototype for the Manipulator Positioning Mechanism (MPM) and Manipulator Retention Latches (MRL) of the PDRS has been developed and successfully demonstrated during the STS-49 and STS-46 missions. Expert systems for monitoring real-time operations must not only accurately represent domain knowledge, but also address the challenges of using unfiltered real-time data as input. This paper describes the methods and design strategies developed to overcome problems with real-time data in the NASA Mission Control Center. Types of data problems addressed are as follows: (1) loss of data; (2) erratic data; and (3) data lags and irregularities during state transition. Methods used to handle data problems include rule disabling for ignoring data when data quality is uncertain, context-sensitive bounded pattern recognition for minimizing incorrect conclusions based on bad data, and graceful recovery through system correction when reliable data returns. This combination of methods with an object-based modular DESSY design assures a robust program capable of lengthy periods of uninterrupted use in operations.

Land, Sherry A.↗
NASA NTRS2008

Swarm Verification

Reportedly, supercomputer designer Seymour Cray once said that he would sooner use two strong oxen to plow a field than a thousand chickens. Although this is undoubtedly wise when it comes to plowing a field, it is not so clear for other types of tasks. Model checking problems are of the proverbial "search the needle in a haystack" type. Such problems can often be parallelized easily. Alas, none of the usual divide and conquer methods can be used to parallelize the working of a model checker. Given that it has become easier than ever to gain access to large numbers of computers to perform even routine tasks it is becoming more and more attractive to find alternate ways to use these resources to speed up model checking tasks. This paper describes one such method, called swarm verification.

grid computing↗
NASA NTRS2006

NASA Taxonomies for Searching Problem Reports and FMEAs

Many types of hazard and risk analyses are used during the life cycle of complex systems, including Failure Modes and Effects Analysis (FMEA), Hazard Analysis, Fault Tree and Event Tree Analysis, Probabilistic Risk Assessment, Reliability Analysis and analysis of Problem Reporting and Corrective Action (PRACA) databases. The success of these methods depends on the availability of input data and the analysts knowledge. Standard nomenclature can increase the reusability of hazard, risk and problem data. When nomenclature in the source texts is not standard, taxonomies with mapping words (sets of rough synonyms) can be combined with semantic search to identify items and tag them with metadata based on a rich standard nomenclature. Semantic search uses word meanings in the context of parsed phrases to find matches. The NASA taxonomies provide the word meanings. Spacecraft taxonomies and ontologies (generalization hierarchies with attributes and relationships, based on terms meanings) are being developed for types of subsystems, functions, entities, hazards and failures. The ontologies are broad and general, covering hardware, software and human systems. Semantic search of Space Station texts was used to validate and extend the taxonomies. The taxonomies have also been used to extract system connectivity (interaction) models and functions from requirements text. Now the Reconciler semantic search tool and the taxonomies are being applied to improve search in the Space Shuttle PRACA database, to discover recurring patterns of failure. Usual methods of string search and keyword search fall short because the entries are terse and have numerous shortcuts (irregular abbreviations, nonstandard acronyms, cryptic codes) and modifier words cannot be used in sentence context to refine the search. The limited and fixed FMEA categories associated with the entries do not make the fine distinctions needed in the search. The approach assigns PRACA report titles to problem classes in the taxonomy. Each ontology class includes mapping words - near-synonyms naming different manifestations of that problem class. The mapping words for Problems, Entities and Functions are converted to a canonical form plus any of a small set of modifier words (e.g. non-uniformity NOT + UNIFORM.) The report titles are parsed as sentences if possible, or treated as a flat sequence of word tokens if parsing fails. When canonical forms in the title match mapping words, the PRACA entry is associated with the corresponding Problem, Entity or Function in the ontology. The user can search for types of failures associated with types of equipment, clustering by type of problem (e.g., all bearings found with problems of being uneven: rough, irregular, gritty ). The results could also be used for tagging PRACA report entries with rich metadata. This approach could also be applied to searching and tagging failure modes, failure effects and mitigations in FMEAs. In the pilot work, parsing 52K+ truncated titles (the test cases that were available), has resulted in identification of both a type of equipment and type of problem in about 75% of the cases. The results are displayed in a manner analogous to Google search results. The effort has also led to the enrichment of the taxonomy, adding some new categories and many new mapping words. Further work would make enhancements that have been identified for improving the clustering and further reducing the false alarm rate. (In searching for recurring problems, good clustering is more important than reducing false alarms). Searching complete PRACA reports should lead to immediate improvement.

Malin, Jane T.↗