Search NASA⌕ Search

SEARCH · Search NASA

Results for “UNIFORM FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Modeling ice streams: Derived quantities

The model addressed is a finite-element, map-plane, time-dependent, column-averaged continuity equation solver. The key to the fitting process involves the balance between ice motion dominated by flow in internal layers, and ice motion dominated by sliding at the bed. The fitting process involves an iterative process carried out in the time domain. Beginning with the portion of the ice sheet being modeled identical to the present ice sheet with uniform flow, sliding, and fraction specified at nominal values, the model monitors each nodal point surface elevation. As the calculated surface elevation deviates from the present surface, a correction proportional to the difference is applied to selected parameter sets. This correction is in a sense that would tend to improve the fit at the particular nodal point. A calculated surface elevation that was higher than the present surface would result in an increased fraction, which would tend to lower the calculated surface (if the flow or sliding constant were being used as the fitting parameter, they would be lowered to improve the fit). This process is allowed to proceed as long as is necessary for the situation to stabilize. Typically, this takes tens of thousands of model years, but the rate is dependent on other external forcings such as the accumulation rate. The primary result is that while a typical sample of ice streams from around Antarctica can be fitted quite reasonably using only the fraction of the velocity due to sliding, a different mechanism seems to be in play along the Siple Coast, where reduced sliding constants are required to attain a reasonable fit. Flow is more strongly channelized in this region, and velocities are, in general, higher than are observed in other regions. It is unlikely that the mechanism that controls the ice movement along the Siple Coast is exactly similar to the mechanisms in the other ice streams. The concept of deformable sediments and their contribution to the fast flow along the Siple Coast may have limited applicability to other Antarctic ice streams.

Fastook, James↗
NASA NTRS1992

Direct particle simulation on the Connection Machine CM-2

Particle simulation is a useful technique for analyzing low density flows. The Connection Machine CM-2 is a useful test bed for studying the fine-grain data objects decomposition and the coarse-grain domain decomposition single instruction multiple datastream (SIMD) approaches to particle simulation. Both approaches are investigated for the model problem of uniform flow through a channel and the algorithms required for the SIMD domain decomposition approach are presented. An unresolved issue with the domain decomposition approach is the effect of a poor partitioning on flows with real geometries. Initial results with the channel flow problem indicate that a poor partitioning has only a small detrimental effect on the overall performance.

Dagum, L.↗
NASA NTRS1993

Ducted fan acoustic radiation including the effects of nonuniform mean flow and acoustic treatment

Forward and aft acoustic propagation and radiation from a ducted fan is modeled using a finite element discretization of the acoustic field equations. The fan noise source is introduced as equivalent body forces representing distributed blade loading. The flow in and around the nacelle is assumed to be nonuniform, reflecting the effects of forward flight and flow into the inlet. Refraction due to the fan exit jet shear layer is not represented. Acoustic treatment on the inlet and exhaust duct surfaces provides a mechanism for attenuation. In a region enclosing the fan a pressure formulation is used with the assumption of locally uniform flow. Away from the fan a velocity potential formulation is used and the flow is assumed nonuniform but irrotational. A procedure is developed for matching the two regions by making use of local duct modal amplitudes as transition state variables and determining the amplitudes by enforcing natural boundary conditions at the interface between adjacent regions in which pressure and velocity potential are used. Simple models of rotor alone and rotor/exit guide vane generated noise are used to demonstrate the calculation of the radiated acoustic field and to show the effect of acoustic treatment. The model has been used to assess the success of four techniques for acoustic lining optimization in reducing far field noise.

Eversman, Walter↗
DOE OSTI2024

Electrical Resistivity Tomography Monitoring of In Situ Soil Flushing at the Hanford 100-K East Area: 100KE Soil Flushing Monitoring

Former operations in the 100-KE Area at the Hanford Site resulted in vadose zone hexavalent chromium that provides a source of groundwater contamination. Previous efforts to remediate vadose zone chromium involved excavation and offsite treatment of contaminated soils. Although much of the chromium was removed, contamination still exists in native soil between the water table and the bottom of the pit, which has since been backfilled. In-situ soil flushing was tested at the 100-KE Area to accelerate the removal of the remaining hexavalent chromium in the vadose zone. Soil flushing works by applying clean flush water at the surface, which mobilizes and transports chromium as it migrates downward to the water table. Once the chromium reaches the water table, it is hydraulically contained, extracted, and treated through pump and treat operations. The efficacy of soil flushing is directly related to the volume of clean water that infiltrates through contaminated soils. Therefore, performance monitoring requires and understanding of flush water migration through the vadose zone. It is challenging to comprehensively assess soil flushing performance via borehole access due to the limited volume of investigation afforded by a given wellbore. As an alternative, 3D time-lapse electrical resistivity tomography (ERT) was tested as a method of monitoring the distribution of flush water over time within the vadose zone. ERT is a method of imaging the bulk electrical conductivity of the subsurface, which is highly dependent on water saturation levels in unconsolidated and unsaturated sediments. Thus, the timing and location of changes in bulk conductivity caused by soil flushing can be used to infer flush water migration pathways. In this report we present results of 3D time-lapse ERT imaging during two separate soil flushing campaigns conducted during the spring and summer months of 2022 and 2023. Results show generally that: 1) Pit backfill materials appear to nominally have larger permeability than native soils. Consequently, the boundary between pit backfill and native soil had a significant impact on flush water migration, causing some flush water to migrate along the pit boundary to the bottom of the pit. 2) Non-uniform flows, likely caused by variations in hydrogeologic properties, developed in the pit backfill materials, resulting in uneven flush water distribution on the southern margin of the soil flushing zone. 3) Redistribution of water at the interface between backfill materials and Hanford formation materials likely facilitated elevated and uniform distribution of flush water within native soils beneath the deeper parts of the pit boundary beneath the center of the flush zone, which presumably overlie soils with elevated chromium contamination. These areas appear to have been infiltrated by higher volumes of flush water than the northern and southern margins of the flush zone. 4) In comparison to 2022, high flush water application rates significantly improved flush water distribution throughout the target flushing zone. 5) Imaging resolution was limited to a depth of approximate 20 meters below the land surface, due primarily to limitations on the lateral extent of the surface ERT array. The ~10 m region of the vadose zone between approximately 130 meters elevation and the water table at approximately 120 meters elevation was unresolved.

100 Area↗
NASA NTRS1983

Sound propagation in segmented exhaust ducts - Theoretical predictions and comparison with measurements

Suppressions due to acoustic treatment in the annular exhaust duct of a model fan have been theoretically predicted and compared with measurements. The predictions are based on the modal analysis of sound propagation in a straight annular flow duct with segmented treatment. Measured values of the mode distribution of the fan noise source (fan-stator interaction source only) and the acoustic impedance of the treatment in the duct were used as input to the prediction program. The predicted suppressions (under the assumption of uniform flow in the duct) compared well with the measured in-duct suppression for all test conditions. The measurements were made in an anechoic chamber and the interaction modes generated in the fan spanned a cut-off ratio range from nearly one to seven.

Joshi, M. C.↗
NASA NTRS1991

Numerical investigations in three-dimensional internal flows

The general objectives of NASA's Generic Hypersonics Research Program (GHP) are to develop a technology background required for aeronautical research in the hypersonic Mach number flow range. These research efforts are to complement the National Aerospace Plane (NASP) Program and are geared toward the development of experimental and computational fluid dynamics (CFD) techniques. One of the prominent goals of inlet design for high speed applications is to produce an inlet that delivers uniform flow at its exit in the shortest possible distance. In previous studies, the technologies for determining contours for both the ramp and cowl were demonstrated that allowed a nearly shock free exiting flow field to be obtained. This technology was developed further during the present reporting period and applied to a preliminary design investigation of a biconic hypersonic research vehicle with a nearly 2-D inlet attached near the aft end of the vehicle. The results of a parametric investigation of this proposed inlet for freestream Mach numbers between 10 and 15 are described.

Rose, William C.↗
NASA NTRS1974

An oscillatory kernel function method for lifting surfaces in mixed transonic flow

A study was conducted on the use of combined subsonic and supersonic linear theory to obtain economical and yet realistic solutions to unsteady transonic flow problems. With some modification, existing linear theory methods were combined into a single computer program. The method was applied to problems for which measured steady Mach number distributions and unsteady pressure distributions were available. By comparing theory and experiment, the transonic method showed a significant improvement over uniform flow methods. The results also indicated that more exact local Mach number effects and normal shock boundary conditions on the perturbation potential were needed. The validity of these improvements was demonstrated by application to steady flow.

Cunningham, A. M., Jr.↗
NASA NTRS1985

NASTRAN supplemental documentation for modal forced vibration analysis of aerodynamically excited turbosystems

This report is a supplemental NASTRAN document for a new capability to determine the vibratory response of turbosystems subjected to aerodynamic excitation. Supplements of NASTRAN Theoretical, User's, Programmer's, and Demonstration Manuals are included. Turbosystems such as advanced turbopropellers with highly swept blades, and axial-flow compressors and turbines can be analyzed using this capability, which has been developed and implemented in the April 1984 release of the general purpose finite element program NASTRAN. The dynamic response problem is addressed in terms of the normal modal coordinates of these tuned rotating cyclic structures. Both rigid and flexible hubs/disks are considered. Coriolis and centripetal accelerations, as well as differential stiffness effects are included. Generally nonuniform steady inflow fields and uniform flow fields arbitrarily inclined at small angles with respect to the axis of rotation of the turbosystem are considered as the sources of aerodynamic excitation. The spatial nonuniformities are considered to be small deviations from a principally uniform inflow. Subsonic relative inflows are addressed, with provision for linearly interpolating transonic airloads.

Elchuri, V.↗
NASA NTRS1985

Instability of time-periodic flows

The instabilities of some spatially and/or time-periodic flows are discussed, in particular, flows with curved streamlines which can support Taylor-Gortler vortices are described in detail. The simplest flow where this type of instability can occur is that due to the torsional oscillations of an infinitely long circular cylinder. For more complicated spatially varying time-periodic flows, a similar type of instability can occur and is spatially localized near the most unstable positions. When nonlinear effects are considered it is found that the instability modifies the steady streaming boundary layer induced by the oscillatory motion. It is shown that a rapidly rotating cylinder in a uniform flow is susceptible to a related type of instability; the appropriate stability equations are shown to be identical to those which govern the instability of a boussinesq fluid of Prandtl number unity heated time periodically from below.

Hall, P.↗
NASA NTRS1987

Instability of time-periodic flows

The instabilities of some spatially and/or time-periodic flows are discussed, in particular, flows with curved streamlines which can support Taylor-Gortler vortices are described in detail. The simplest flow where this type of instability can occur is that due to the torsional oscillations of an infinitely long circular cylinder. For more complicated spatially varying time-periodic flows, a similar type of instability can occur and is spatially localized near the most unstable positions. When nonlinear effects are considered it is found that the instability modifies the steady streaming boundary layer induced by the oscillatory motion. It is shown that a rapidly rotating cylinder in a uniform flow is susceptible to a related type of instability; the appropriate stability equations are shown to be identical to those which govern the instability of a Boussinesq fluid of Prandtl number unity heated time periodically from below.

Hall, Philip↗
NASA NTRS1974

Acoustic theory of axisymmetric multisectioned ducts

Equations are developed for the acoustic field in a duct system which is made up of a number of connected circular and annular ducts. These equations are suitable for finding the acoustic field inside of and radiated from an aircraft turbofan engine. Acoustic modes are used as generalized coordinates in order to develop a set of matrix equations for the acoustic field. Equations for these modes are given for circular and annular ducts with uniform flow. Modal source equations are derived for point acoustic sources. General equations for mode transmission and reflection are developed and detailed equations are derived for ducts with multiple sections of acoustic treatment and for ducts with circumferential splitter rings. The general theory is applied to the special case of a uniform area circular duct with multisection liners and it is shown that the mode reflection effects are proportional to differences of the acoustic admittances of adjacent liners. A numerical example is given which shows that multisection liners may provide greater noise suppression than uniform liners.

Zorumski, W. E.↗
NASA NTRS1983

Effect of swaging on the 1000 C compressive slow plastic flow characteristics of the directionally solidified eutectic alloy gamma/gamma prime-alpha

Swaging between 750 and 1050 C has been investigated as a means to introduce work into the directionally solidified eutectic alloy gamma/gamma prime-alpha (Ni-32.3 wt percent Mo-6.3 wt percent Al) and increase the elevated temperature creep strength. The 1000 C slow plastic compressive flow stress-strain rate properties in air of as-grown, annealed, and worked nominally 10 and 25 percent materials have been determined. Swaging did not improve the slow plastic behavior. In fact large reductions tended to degrade the strength and produced a change in the deformation mechanism from uniform flow to one involving intense slip band formation. Comparison of 1000 C tensile and compressive strength-strain rate data reveals that deformation is independent of the stress state.

Whittenberger, J. D.↗
NASA NTRS1956

Dynamic Investigation of Release Characteristics of a Streamlined Internal Store from a Simulated Bomb Bay of the Republic F-105 Airplane at Mach Numbers of 0.8, 1.4, and 1.98, Coord. No. AF-222

An investigation has been conducted in the 27- by 27-inch preflight jet of the Langley Pilotless Aircraft Research Station at Wallops Island, Va., of the release characteristics of a dynamically scaled streamlined-type internally carried store from a simulated bomb bay at Mach numbers M(sub o) of 0.8, 1.4, and 1.98. A l/17-scale model of the Republic F-105 half-fuselage and bomb-bay configuration was used with a streamlined store shape of a fineness ratio of 6.00. Simulated altitudes were 3,400 feet at M(sub o) = 0.8, 3,400, and 29,000 feet at M(sub o) = 1.4, and 29,000 feet at M(sub o) = 1.98. At supersonic speeds, high pitching moments are induced on the store in the vicinity of the bomb bay at high dynamic pressures. Successful ejections could not be made with the original configuration at supersonic speeds at near sea-level conditions. The pitching moments caused by unsymmetrical pressures on the store in a disturbed flow field were overcome by replacing the high-aspect-ratio fin with a low-aspect-ratio fin that had a 30-percent area increase which was less subject to aeroelastic effects. Release characteristics of the store were improved by orienting the fins so that they were in a more uniform flow field at the point of store release. The store pitching moments were shown to be reduced by increasing the simulated altitude. Favorable ejections were made at subsonic speeds at near sea-level conditions.

Lee, John B.↗
NASA NTRS1995

Active control of panel vibrations induced by a boundary layer flow

The problems of active and passive control of sound and vibration has been investigated by many researchers for a number of years. However, few of the articles are concerned with the sound and vibration with flow-structure interaction. Experimental and numerical studies on the coupling between panel vibration and acoustic radiation due to flow excitation have been done by Maestrello and his associates at NASA/Langley Research Center. Since the coupled system of nonlinear partial differential equations is formidable, an analytical solution to the full problem seems impossible. For this reason, we have to simplify the problem to that of the nonlinear panel vibration induced by a uniform flow or a boundary-layer flow with a given wall pressure distribution. Based on this simplified model, we have been able to consider the control and stabilization of the nonlinear panel vibration, which have not been treated satisfactorily by other authors. Although the sound radiation has not been included, the vibration suppression will clearly reduce the sound radiation power from the panel. The major research findings are presented in three sections. In section two we describe results on the boundary control of nonlinear panel vibration, with or without flow excitation. Sections three and four are concerned with some analytical and numerical results in the optimal control of the linear and nonlinear panel vibrations, respectively, excited by the flow pressure fluctuations. Finally, in section five, we draw some conclusions from research findings.

Chow, Pao-Liu↗
NASA NTRS1998

Active Control of Panel Vibrations Induced by a Boundary Layer Flow

In recent years, active and passive control of sound and vibration in aeroelastic structures have received a great deal of attention due to many potential applications to aerospace and other industries. There exists a great deal of research work done in this area. Recent advances in the control of sound and vibration can be found in the several conference proceedings. In this report we will summarize our research findings supported by the NASA grant NAG-1-1175. The problems of active and passive control of sound and vibration has been investigated by many researchers for a number of years. However, few of the articles are concerned with the sound and vibration with flow-structure interaction. Experimental and numerical studies on the coupling between panel vibration and acoustic radiation due to flow excitation have been done by Maestrello and his associates at NASA/Langley Research Center. Since the coupled system of nonlinear partial differential equations is formidable, an analytical solution to the full problem seems impossible. For this reason, we have to simplify the problem to that of the nonlinear panel vibration induced by a uniform flow or a boundary-layer flow with a given wall pressure distribution. Based on this simplified model, we have been able to study the control and stabilization of the nonlinear panel vibration, which have not been treated satisfactorily by other authors. The vibration suppression will clearly reduce the sound radiation power from the panel. The major research findings will be presented in the next three sections. In Section II we shall describe our results on the boundary control of nonlinear panel vibration, with or without flow excitation. Section III is concerned with active control of the vibration and sound radiation from a nonlinear elastic panel. A detailed description of our work on the parametric vibrational control of nonlinear elastic panel will be presented in Section IV. This paper will be submitted to the Journal of Acoustic Society of America for publication.

Chow, Pao-Liu↗
DOE OSTI2023

QES-Plume v1.0: a Lagrangian dispersion model

Low-cost simulations providing accurate predictions of transport of airborne material in urban areas, vegetative canopies, and complex terrain are demanding because of the small-scale heterogeneity of the features influencing the mean flow and turbulence fields. Common models used to predict turbulent transport of passive scalars are based on the Lagrangian stochastic dispersion model. The Quick Environmental Simulation (QES) tool is a low-computational-cost framework developed to provide high-resolution wind and concentration fields in a variety of complex atmospheric-boundary-layer environments. Part of the framework, QES-Plume, is a Lagrangian dispersion code that uses a time-implicit integration scheme to solve the generalized Langevin equations which require mean flow and turbulence fields. Here, QES-Plume is driven by QES-Winds, a 3D fast-response model that computes mass-consistent wind fields around buildings, vegetation, and hills using empirical parameterizations, and QES-Turb, a local-mixing-length turbulence model. In this paper, the particle dispersion model is presented and validated against analytical solutions to examine QES-Plume’s performance under idealized conditions. In particular, QES-Plume is evaluated against a classical Gaussian plume model for an elevated continuous point-source release in uniform flow, the Lagrangian scaling of dispersion in isotropic turbulence, and a non-Gaussian plume model for an elevated continuous point-source release in a power-law boundary-layer flow. In these cases, QES-Plume yields a maximum relative error below 6 % when compared with analytical solutions. In addition, the model is tested against wind-tunnel data for a uniform array of cubical buildings. QES-Plume exhibits good agreement with the experiment with 99 % of matched zeros and 59 % of the predicted concentrations falling within a factor of 2 of the experimental concentrations. Furthermore, results also emphasize the importance of using high-quality turbulence models for particle dispersion in complex environments. Finally, QES-Plume demonstrates excellent computational performance.

58 GEOSCIENCES↗
DOE OSTI2024

Reaction dynamics of S( 3 P) with 1,3-butadiene and isoprene: crossed-beam scattering, low-temperature flow experiments, and high-level electronic structure calculations

Sulfur atoms serve as key players in diverse chemical processes, from astrochemistry at very low temperature to combustion at high temperature. Building upon our prior findings, showing cyclization to thiophenes following the reaction of ground-state sulfur atoms with dienes, we here extend this investigation to include many additional reaction products, guided by detailed theoretical predictions. The outcomes highlight the complex formation of products during intersystem crossing (ISC) to the singlet surfaces. Here, we employed crossed-beam velocity map imaging and high-level ab initio methods to explore the reaction of S( 3 P) with 1,3-butadiene and isoprene under single-collision conditions and in low-temperature flows. For the butadiene reaction, our experimental results show the formation of thiophene via H 2 loss, a 2H-thiophenyl radical through H loss, and thioketene through ethene loss at a slightly higher collision energy compared to previous observations. Complementary Chirped-Pulse Fourier-Transform mmWave spectroscopy (CP-FTmmW) measurements in a uniform flow confirmed the formation of thioketene in the reaction at 20 K. For the isoprene reaction, we observed analogous products along with the 2H-thiophenyl radical arising from methyl loss and C 3 H 4 S (loss of ethene or H 2 + acetylene). CP-FTmmW detected the formation of thioformaldehyde via loss of 1,3-butadiene, again in the 20 K flow. Coupled-cluster calculations on the pathways found by the automated kinetic workflow code KinBot support these findings and indicate ISC to the singlet surface, leading to the generation of various long-lived intermediates, including 5-membered heterocycles.

Lang, Jinxin↗
DOE OSTI2026

Holistic energy analysis method for thermal management architectures of data centers

Modern high-performance computing (HPC) data centers (DCs), particularly those supporting energy-intensive artificial intelligence (AI) workloads, face escalating thermal management challenges that degrade performance through thermal throttling and drive up cooling power consumption and operational costs. To address this challenge, many have developed a wide variety of thermal management solutions (single-phase, two-phase, direct, indirect, hybrid, and more) which attempt to cool HPC DCs effectively while attempting to minimize overall system power consumption. However, the analysis of these solutions and methods to effectively compare one with another is lacking. Overall power usage effectiveness (PUE) and total-power usage effectiveness (TUE) provide a metric to quantify power consumption but fail to identify components in the system which require further optimization. To address this, we propose a holistic analytical framework – the waterfall diagram (WFD) – which leverages a waterfall chart methodology, offering a comprehensive visualization of both the thermal management system loop and heat flow pathways from individual server components to the outdoor ambient. Use of the WFD enables graphical estimations of power efficiency and cooling performance across each component of a DC cooling system and complements Sankey-style energy flow visualizations by additionally resolving stage-wise temperature changes and incremental TUE contributions. The framework is used in conjunction with simulation-based approaches, to conduct a detailed pressure drop and flow distribution analysis aimed at identifying the optimal coolant distribution architecture for a single-phase direct-to-chip water-cooled DC, which serves as the baseline for subsequent WFD analysis. Among the evaluated architectures, the 3 U modular coolant distribution architecture is found to demonstrate the best performance, considering minimal pressure drop and uniform flow distribution. In addition, TUE is calculated for each cooling loop component based on its associated pressure drop and corresponding pumping power, which are integrated into the WFD. This correlation between TUE and local temperature offers immediate insight into the power efficiency and thermal performance contributions of individual components, facilitating further development and optimization. Examples of WFD applications are presented under varying thermal loads and ambient conditions, demonstrating reasonable cooling strategies. Notably, the 3 U modular architecture maintains a consistent chip case temperature of 85°C, achieving a TUE of 1.016 at ambient temperature of 47°C, and a TUE of 1.026 at ambient temperature of 52°C. The WFD methodology provides an efficient, holistic, and streamlined framework for DC thermal management architecture assessment and enables design optimization which is important for addressing the thermal-fluidic energy challenges of current and next-generation DCs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗