The influence of fixture stress concentrations on ring accelerometers
Ring accelerometer errors from stresses developed by fixture vibrations
Henley, C. E., Jr.↗
SEARCH · Search NASA
Results for “VIBRATIONAL STRESS”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Adaptable structural synthesis using advanced analysis and optimization coupled by a computer operating system
A finite element program is linked with a general purpose optimization program in a 'programing system' which includes user supplied codes that contain problem dependent formulations of the design variables, objective function and constraints. The result is a system adaptable to a wide spectrum of structural optimization problems. In a sample of numerical examples, the design variables are the cross-sectional dimensions and the parameters of overall shape geometry, constraints are applied to stresses, displacements, buckling and vibration characteristics, and structural mass is the objective function. Thin-walled, built-up structures and frameworks are included in the sample. Details of the system organization and characteristics of the component programs are given.
Sobieszczanski-Sobieski, J.↗
Reverse thrust performance of the QCSEE variable pitch turbofan engine
Results of steady state reverse and forward to reverse thrust transient performance tests are presented. The original quiet, clean, short haul, experimental engine four segment variable fan nozzle was retested in reverse and compared with a continuous, 30 deg half angle conical exlet. Data indicated that the significantly more stable, higher pressure recovery flow with the fixed 30 deg exlet resulted in lower engine vibrations, lower fan blade stress, and approximately a 20 percent improvement in reverse thrust. Objective reverse thrust of 35 percent of takeoff thrust was reached. Thrust response of less than 1.5 sec was achieved for the approach and the takeoff to reverse thrust transients.
Samanich, N. E.↗
Reverse thrust performance of the QCSEE variable pitch turbofan engine
Results of steady-state reverse and forward-to-reverse thrust transient performance tests are presented. The original QCSEE 4-segment variable fan nozzle was retested in reverse and compared with a continuous, 30-deg half-angle conical exlet. Data indicated that the significantly more stable, higher pressure recovery flow with the fixed 30-deg exlet resulted in lower engine vibrations, lower fan blade stress and approximately a 20% improvement in reverse thrust. Objective reverse thrust of 35% of takeoff thrust was reached. Thrust response of less than 1.5 sec was achieved for the approach and the takeoff-to-reverse thrust transients.
Samanich, N. E.↗
Influence of stress, weightlessness, and simulated weightlessness on differentiation of preosteoblasts
The effects of 18.5 days of weightlessness aboard a satellite, stress of restricted feeding, stress of noise and vibration to simulate space flight and 21 days of head down suspension via the Morey-Holton model for simulated weightlessness was studied. Nuclear size of fibroblastlike cells in PDL on the anterior surface of maxillary first molars was classified as: (1) A-cells, self perpetuating precursors with a nuclear volume 80 micron B-cells, nonosteogenic fibroblasts with a nuclear volume of 80-119 micron 3, C-cells, preosteoblasts that are in G1 stage of the cell cycle with a nuclear size of 120-170 micro, and D-cells, preosteoblasts that are in G2 stage of the cell cycle with a nuclear size 170 micro.
Roberts, W. E.↗
High-Performance Filleting and Channel Sealants
Filleting and channel sealants developed for sealing cavities in wings and fusealage of aircraft. Both sealants function well at 177 degrees C, as required in current specifications for supersonic aircraft. Sealants have excellent resistance to fuel and other solvents. They stay flexible, resistant to vibrational, thermal, and mechanical stresses, and adhere well to aluminum. Prove useful in industrial applications requiring resistance to solvents at high temperatures.
Rosser, R. W.↗
A finite element formulation for the large deflection random response of thermally buckled beams
The effects of temperature and acoustic loading are included in a theoretical finite element large deflection formulation for thin, isotropic beams. Thermal loads are applied as steady-state temperature distributions, and acoustic loads are taken to be ergodic and Gaussian with zero mean and uniform magnitude and phase along the length of the beam. Material properties are considered presently to be independent of temperature. Also, inplane and rotary inertia terms are assumed to be negligible, and all inplane edge conditions are taken to be immovable. For the random response analysis, both auto- and cross-correlation terms are included. The nature of the loads leads to the solution of two separate problems. First, the problem of thermal postbuckling is solved to determine the deflections and stresses due to the thermal load only. These deflections and stresses are then used as initial deflections and stresses for the random vibration analysis. Root-mean-square (RMS) maximum deflections and strains are obtained and compared with previous classical equivalent linearization results.
Locke, James↗
Rotorcraft airframe structural optimization for combined vibration and fatigue constraints
This paper addresses the application of a formal optimization technique in rotorcraft airframe structural design studies to reduce the structural weight, to lower airframe vibrations, and to enhance fatigue life of the structure. Vibration and fatigue considerations in airframe design are described. An optimization methodology based on the use of a nonlinear programming technique to size airframe structural members subjected to constraints on weight, vibration response and fatigue stresses under dynamic loads, are described. The paper focuses on the development of necessary computational tools for airframe structural optimization and describes the sensitivity analysis procedure for these types of design constraints. Further, the paper describes the optimization procedure as implemented in a computer code called DYNOPT which is a unique operational combination of several newly developed Fortran codes as well as modification of existing codes consisting of the direct matrix abstraction modules of the MSC/NASTRAN Program and CONMIN optimizer. The application of the optimization procedure is demonstrated using an elastic-line model of the Bell AH-1G helicopter airframe structure and computational results are discussed.
Sareen, Ashish K.↗
A study of the Lute Metering Structure
Two Metering Structure configurations were investigated. The first case was the traditional style metering structure which is larger than the outside diameter of the primary mirror. The second case investigated was the center support concept in which the outside diameter of the structure is less than the inside diameter of the primary mirror. Beryllium was used as the baseline material for this study. Four other materials were considered as candidates for the metering structure. These materials are: Graphite Epoxy, Aluminum, Titanium, and Invar. The loading conditions used for this study were estimated to be: Quasi Static: 6.0 G (all three directions); and Random Vibration: 30.0 G (applied 1 axis at a time). Taking advantage of symmetry, it was necessary to apply the lateral loading to only one axis. These loads were applied to both concepts and to all material configurations. The loadings as described above were based on the best available information and is felt to be adequate for this study since it was consistently used for all configurations. A load factor 2.00 was applied to both quasi static and random vibration loads. The allowable stresses are conservatively based yield strength of the material, except for the struts which are controlled by elastic stability. The stresses determined from each individual loading direction were conservatively combined by the absolute sum method.
Foreman, James W.↗
Investigation of Mechanisms of Blade Failure of Forged Hastalloy B and Cast Stellite 21 Turbine Blades in Turbojet Engine
An investigation was conducted to study the mechanisms of blade failure of forged Hastelloy B and cast Stellite 21. The blades were mounted in a 16-25-6 alloy rotor and subjected to 20-minute cycles consisting of 15 minutes at rated speed and approximately 5 minutes at idle. The first failures of the Hastelloy B and Stellite 21 blades were probably the result of excessive vibratory stresses and occurred after 14.25 and 16.75 hours, respectively. After 28.75 hours of operation, all but 3 of the original 25 Hastelloy B blades had either failed or contained stress-rupture-type cracks and four of the original 27 Stellite 21 blades contained stress-rupture-type cracks.
ENGINES, TURBO-JET↗
Relation of Engine Turbine-blade Life to Stress-rupture Properties of the Alloys, Stellite 21, Hastelloy B, Cast S-816, Forged S-816, X-40, Nimonic 80, Refractaloy 26, N-155, and Inconel X
An investigation was conducted to relate the engine performance of the heat-resistant alloys, Stellite 21, Hastelloy B, cast S-816, forged S-816, X-40, Nimonic 80, Refractory 26, N-155, and Iconel X to their stress-rupture properties. The engine test consisted of the repetition of a 20-minute cycle, 15 minutes at rated speed and approximately 5 minutes at idle. The results of the investigation indicated a direct correlation between stress-rupture life and blade life for the relatively low-strength alloys. The stress-rupture life and blade life for the relatively high-strength alloys did not correlate because of the effects of the vibratory stresses and the corrosive-gas atmosphere.
ALLOYS, HEAT-RESISTING↗
Considerations of wake-excited vibratory stress in a pusher propeller
Explore the source record for details and available documents.
PROPELLERS - CHARACTERISTICS - EFFECT OF COMPRESSI↗
The structure of Airy's stress function in multiply connected regions
In solving two-dimensional problems using Airy's stress function for multiply connected regions, the form of the function depends on the dislocations and boundary forces present. The structure of Airy's function is shown to consist of a part expressible in terms of boundary forces and a part expressible in the manner of Poincare. Meanings of the constants occurring in Poincare's expression are discussed.
FRAMES, GRIDWORKS AND TRUSSES↗
NASA Tech Briefs, September 2011
Topics covered include: Fused Reality for Enhanced Flight Test Capabilities; Thermography to Inspect Insulation of Large Cryogenic Tanks; Crush Test Abuse Stand; Test Generator for MATLAB Simulations; Dynamic Monitoring of Cleanroom Fallout Using an Air Particle Counter; Enhancement to Non-Contacting Stress Measurement of Blade Vibration Frequency; Positively Verifying Mating of Previously Unverifiable Flight Connectors; Radiation-Tolerant Intelligent Memory Stack - RTIMS; Ultra-Low-Dropout Linear Regulator; Excitation of a Parallel Plate Waveguide by an Array of Rectangular Waveguides; FPGA for Power Control of MSL Avionics; UAVSAR Active Electronically Scanned Array; Lockout/Tagout (LOTO) Simulator; Silicon Carbide Mounts for Fabry-Perot Interferometers; Measuring the In-Process Figure, Final Prescription, and System Alignment of Large; Optics and Segmented Mirrors Using Lidar Metrology; Fiber-Reinforced Reactive Nano-Epoxy Composites; Polymerization Initiated at the Sidewalls of Carbon Nanotubes; Metal-Matrix/Hollow-Ceramic-Sphere Composites; Piezoelectrically Enhanced Photocathodes; Iridium-Doped Ruthenium Oxide Catalyst for Oxygen Evolution; Improved Mo-Re VPS Alloys for High-Temperature Uses; Data Service Provider Cost Estimation Tool; Hybrid Power Management-Based Vehicle Architecture; Force Limit System; Levitated Duct Fan (LDF) Aircraft Auxiliary Generator; Compact, Two-Sided Structural Cold Plate Configuration; AN Fitting Reconditioning Tool; Active Response Gravity Offload System; Method and Apparatus for Forming Nanodroplets; Rapid Detection of the Varicella Zoster Virus in Saliva; Improved Devices for Collecting Sweat for Chemical Analysis; Phase-Controlled Magnetic Mirror for Wavefront Correction; and Frame-Transfer Gating Raman Spectroscopy for Time-Resolved Multiscalar Combustion Diagnostics.
Source record↗
Pack Density Limitations of Hybrid Parachutes
The development and testing of the Orion crew capsule parachute system has provided a unique opportunity to study dense parachute packing techniques and limits, in order to establish a new baseline for future programs. The density of parachute packs has a significant influence on vibration loads, retention system stresses, and parachute mortar performance. Material compositions and pack densities of existing designs for space capsule recovery were compared, using the pack density of the Apollo main parachutes as the current baseline. The composition of parachutes has changed since Apollo, incorporating new materials such as Kevlar , Vectran , Teflon and Spectra . These materials have different specific densities than Nylon, so the densities of hybrid parachute packs cannot be directly compared to Nylon parachutes for determination of feasibility or volume allocation. Six parachute packs were evaluated in terms of weighted average solid density in order to achieve a non-dimensional comparison of packing density. Means of mitigating damage due to packing pressure and mortar firing were examined in light of the Capsule Parachute Assembly System (CPAS) and Apollo experience. Parachute design improvements including incorporation of modern materials and manufacturing processes serves to make CPAS the new knowledge base on which future spacecraft parachute systems will be built.
Zwicker, Matthew L.↗
Propulsion Aeroelastic Analysis Developed for Flutter and Forced Response
The NASA Glenn Research Center at Lewis Field develops new technologies to increase the fuel efficiency of aircraft engines, improve the safety of engine operation, reduce emissions, and reduce engine noise. With the development of new designs for fans, compressors, and turbines to achieve these goals, the basic aeroelastic requirements are that there should be no flutter (self-excited vibrations) or high resonant blade stresses (due to forced response) in the operating regime. Therefore, an accurate prediction and analysis capability is required to verify the aeroelastic soundness of the designs. Such a three-dimensional viscous propulsion aeroelastic analysis capability has been developed at Glenn with support from the Advanced Subsonic Technology (AST) program. This newly developed aeroelastic analysis capability is based on TURBO, a threedimensional unsteady aerodynamic Reynolds-averaged Navier-Stokes turbomachinery code developed previously under a grant from Glenn. TURBO can model the viscous flow effects that play an important role in certain aeroelastic problems such as flutter with flow separation, flutter at high loading conditions near the stall line (stall flutter), flutter in the presence of shock and boundary-layer interaction, and forced response due to wakes and shock impingement. In aeroelastic analysis, the structural dynamics representation of the blades is based on normal modes. A finite-element analysis code is used to calculate these in-vacuum vibration modes and the associated natural frequencies. In an aeroelastic analysis using the TURBO code, flutter and forced response are modeled as being uncoupled. To calculate if a blade row will flutter, one prescribes the motion of the blade to be a harmonic vibration in a specified in-vacuum normal mode. An aeroelastic analysis preprocessor is used to generate the displacement field required for the analysis. The work done by aerodynamic forces on the vibrating blade during a cycle of vibration is calculated. If this work is positive, the blade is dynamically unstable, since it will extract energy from the flow, leading to an increase in the blade s oscillation amplitude. The forced-response excitations on a blade row are calculated by modeling the flow through two adjacent blade rows using the TURBO code. The blades are assumed to be rigid. As an option, a single blade row can be modeled with the upstream blade row influence represented by a time-varying disturbance (gust) at the inlet boundary. The unsteady forces on a blade row from such analyses are used in a structural analysis along with the blade structural dynamics characteristics and aerodynamic damping associated with blade vibration to calculate the resulting dynamic stresses on the blade.
Bakhle, Milind A.↗
Static and Vibration Analyses of General Wing Structures Using Equivalent Plate Models
An efficient method, using equivalent plate model, is developed for studying the static and vibration analyses of general built-up wing structures composed of skins, spars, and ribs. The model includes the transverse shear effects by treating the built-up wing as a plate following the Reissner-Mindlin theory, the so-called First-order Shear Deformation Theory (FSDT). The Ritz method is used with the Legendre polynomials being employed as the trial functions. This is in contrast to previous equivalent plate model methods which have used simple polynomials, known to be prone to numerical ill-conditioning, as the trial functions. The present developments are evaluated by comparing the results with those obtained using MSC/NASTRAN, for a set of examples. These examples are: (i) free-vibration analysis of a clamped trapezoidal plate with (a) uniform thickness, and (b) non-uniform thickness varying as an airfoil, (ii) free-vibration and static analyses (including skin stress distribution) of a general built-up wing, and (iii) free-vibration and static analyses of a swept-back box wing. The results obtained by the present equivalent plate model are in good agreement with those obtained by the finite element method.
Kapania, Rakesh K.↗
Shell theory automated for rotational structures
Package of numerical integration programs static, buckling, vibration, and plastic analysis on thin sheels of revolution. Sheels may be subjected to distributed loads, concentrated line loads, and thermal strain. Outputs include stresses, displacement, plastic strains, and vibration and buckling results. Program aids design of aircraft bodies, spacecraft, submarines, and storage tanks. Written in FORTRAN IV for batch execution, program has been implemented on UNIVAC 1108.
Key, J.↗