Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND TUNNEL MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Analysis of aeroelastic and resonance responses of a wind tunnel model support system

Vibrations of the National Transonic Facility model support system were analyzed using CAP-TSD (Computational Aeroelasticity Program-Transonic Small Disturbance), a three-dimensional transonic small disturbance potential code designed for aeroelastic analysis of complex configurations. The model support system was represented as a tunnel-spanning flexible wing whose structural properties were obtained from measured responses. Aeroelastic transients were calculated, assuming no structural damping, and analyzed to obtain modal stability characteristics. The results showed that there is a tendency toward a hump mode instability in one of the modes and that there are other weakly damped or unstable modes. The close proximity of the solid wind-tunnel diffuser side walls to the model support system was shown to have adverse effects on its aeroelastic stability characteristics. When the effects of the wind-tunnel walls were modeled, the analyses indicated the presence of wind-tunnel resonance modes which were not present when free-air boundary conditions were used.

Whitlow, Woodrow, Jr.↗
NASA NTRS1977

Aerodynamic coefficient estimation for dynamic wind tunnel models

Maximum likelihood parameter identification is used to estimate the aerodynamic coefficients of a 'flying' aircraft model which is mounted in a transonic wind tunnel by a system of cables and pulleys. The model's motion is governed by both cable and aerodynamic forces, where the parameters to be identified are functions of the aerodynamic forces but cable forces greatly predominate. The test data were successfully processed assuming a linear equation model in the identification procedure. In one instance, the procedure was able to detect a failing measurement instrument. The final parameter estimates are compared to estimates obtained in independent tests of a similar aircraft model.

Mohr, R. L.↗
NASA NTRS1974

A directional microphone array for acoustic studies of wind tunnel models

An end-fire microphone array that utilizes a digital time delay system has been designed and evaluated for measuring noise in wind tunnels. The directional response of both a four- and eight-element linear array of microphones has enabled substantial rejection of background noise and reverberations in the NASA Ames 40- by 80-foot wind tunnel. In addition, it is estimated that four- and eight-element arrays reject 6 and 9 dB, respectively, of microphone wind noise, as compared with a conventional omnidirectional microphone with nose cone. Array response to two types of jet engine models in the wind tunnel is presented. Comparisons of array response to loudspeakers in the wind tunnel and in free field are made.

Soderman, P. T.↗
NASA NTRS1926

Comparison of Tests on Air Propellers in Flight with Wind Tunnel Model Tests on Similar Forms

The purpose of this investigation was to determine the performance, characteristics, and coefficients of full-sized air propellers in flight and to compare these results with those derived from wind-tunnel tests on reduced scale models of similar geometrical form. The full-scale equipment comprised five propellers in combination with a VE-7 airplane and Wright E-4 engine. This part of the work was carried out at the Langley Memorial Aeronautical Laboratory, between May 1 and August 24, 1924, and was under the immediate charge of Mr. Lesley. The model or wind-tunnel part of the investigation was carried out at the Aerodynamic Laboratory of Stanford University and was under the immediate charge of Doctor Durand. A comparison of the curves for full-scale results with those derived from the model tests shows that while the efficiencies realized in flight are close to those derived from model tests, both thrust developed and power absorbed in flight are from 6 to 10 per cent greater than would be expected from the results of model tests.

Durand, W F↗
NASA NTRS2015

Aeroservoelastic Wind-Tunnel Test of the SUGAR Truss Braced Wing Wind-Tunnel Model

The Subsonic Ultra Green Aircraft Research (SUGAR) Truss-Braced Wing (TBW) aeroservoelastic (ASE) wind-tunnel test was conducted in the NASA Langley Transonic Dynamics Tunnel (TDT) and was completed in April, 2014. The primary goals of the test were to identify the open-loop flutter boundary and then demonstrate flutter suppression. A secondary goal was to demonstrate gust load alleviation (GLA). Open-loop flutter and limit cycle oscillation onset boundaries were identified for a range of Mach numbers and various angles of attack. Two sets of control laws were designed for the model and both sets of control laws were successful in suppressing flutter. Control laws optimized for GLA were not designed; however, the flutter suppression control laws were assessed using the TDT Airstream Oscillation System. This paper describes the experimental apparatus, procedures, and results of the TBW wind-tunnel test. Acquired system ID data used to generate ASE models is also discussed.2 study.

Scott, Robert C.↗
NASA NTRS1992

Propulsion simulator for magnetically-suspended wind tunnel models

In order to demonstrate the measurement of aerodynamic forces/moments, including the effects of exhaust jets in Magnetic Suspension and Balance System (MSBS) wind tunnels, two propulsion simulator models were developed at Physical Sciences Inc. (PSI). Both the small-scale model (1 in. diameter X 8 in. long) and the large-scale model (2.5 in. diameter X 15 in. long) employed compressed, liquefied carbon dioxide as a propellant. The small-scale simulator, made from a highly magnetizable iron alloy, was demonstrated in the 7 in. MSBS wind tunnel at the University of Southampton. It developed a maximum thrust of approximate 1.3 lbf with a 0.098 in. diameter nozzle and 0.7 lbf with a 0.295 in. diameter nozzle. The Southampton MSBS was able to control the simulator at angles-of attack up to 20 deg. The large-scale simulator was demonstrated to operate in both a steady-state and a pulse mode via a miniaturized solinoid valve. It developed a stable and repeatable thrust of 2.75 lbf over a period of 4s and a nozzle pressure ratio (NPR) of 5.

Joshi, P. B.↗
NASA NTRS2004

NASA Glenn Wind Tunnel Model Systems Criteria

This report describes criteria for the design, analysis, quality assurance, and documentation of models that are to be tested in the wind tunnel facilities at the NASA Glenn Research Center. This report presents two methods for computing model allowable stresses on the basis of the yield stress or ultimate stress, and it defines project procedures to test models in the NASA Glenn aeropropulsion facilities. Both customer-furnished and in-house model systems are discussed. The functions of the facility personnel and customers are defined. The format for the pretest meetings, safety permit process, and model reviews are outlined. The format for the model systems report (a requirement for each model that is to be tested at NASA Glenn) is described, the engineers responsible for developing the model systems report are listed, and the timetable for its delivery to the project engineer is given.

Soeder, Ronald H.↗
NASA NTRS1974

Small scale wind tunnel model investigation of hybrid high lift systems combining upper surface blowing with the internally blown flap

A small-scale wind tunnel test of a two engine hybrid model with upper surface blowing on a simulated expandable duct internally blown flap was accomplished in a two phase program. The low wing Phase I model utilized 0.126c radius Jacobs/Hurkamp flaps and 0.337c radius Coanda flaps. The high wing Phase II model was utilized for continued studies on the Jacobs/Hurkamp flap. Principal study areas included: basic data both engines operative and with an engine out, control flap utilization, horizontal tail effectiveness, spoiler effectiveness, USB nacelle deflector study and USB/IBF pressure ratio effects.

Waites, W. L.↗
NASA NTRS1993

Assessment of a flow-through balance for hypersonic wind tunnel models with scramjet exhaust flow simulation

The purpose of this investigation were twofold: first, to determine whether accurate force and moment data could be obtained during hypersonic wind tunnel tests of a model with a scramjet exhaust flow simulation that uses a representative nonwatercooled, flow-through balance; second, to analyze temperature time histories on various parts of the balance to address thermal effects on force and moment data. The tests were conducted in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel at free-stream Reynolds numbers ranging from 0.5 to 7.4 x 10(exp 6)/ft and nominal angles of attack of -3.5 deg, 0 deg, and 5 deg. The simulant exhaust gases were cold air, hot air, and a mixture of 50 percent Argon and 50 percent Freon by volume, which reached stagnation temperatures within the balance of 111, 214, and 283 F, respectively. All force and moment values were unaffected by the balance thermal response from exhaust gas simulation and external aerodynamic heating except for axial-force measurements, which were significantly affected by balance heating. This investigation showed that for this model at the conditions tested, a nonwatercooled, flow-through balance is not suitable for axial-force measurements during scramjet exhaust flow simulation tests at hypersonic speeds. In general, heated exhaust gas may produce unacceptable force and moment uncertainties when used with thermally sensitive balances.

Huebner, Lawrence D.↗
NASA NTRS1994

The simulation of a propulsive jet and force measurement using a magnetically suspended wind tunnel model

Models featuring the simulation of exhaust jets were developed for magnetic levitation in a wind tunnel. The exhaust gas was stored internally producing a discharge of sufficient duration to allow nominal steady state to be reached. The gas was stored in the form of compressed gas or a solid rocket propellant. Testing was performed with the levitated models although deficiencies prevented the detection of jet-induced aerodynamic effects. Difficulties with data reduction led to the development of a new force calibration technique, used in conjunction with an exhaust simulator and also in separate high incidence aerodynamic tests.

Garbutt, K. S.↗
NASA NTRS1984

A flying superconducting magnet and cryostat for magnetic suspension of wind-tunnel models

The engineering practicality of a persistent high-field superconducting solenoid cryostat as a magnetic suspension and balance system (MSBS) for wind-tunnel testing of aircraft and missile models is examined. The test apparatus is a simple solenoid of filamentary NbTi superconductor with a cupronickel matrix. The apparatus, with a length-to-diameter ratio of 6 to 1 and a radius of 32 mm, used a 0.25 mm wire with a critical current of 27 A in an external field of 6 T. The total heat inleak of 150 mW was achieved. Helium boiloff rates were tested over a range of operating conditions, including pitch attitudes from 10 deg nose down to 90 deg nose up; the rate was estimated as low, but the aerodynamic acceptability of venting gaseous helium has not been determined. It is shown that the effectiveness of the concept increases with increasing scale, and performance in excess of that of conventional ferromagnets is achievable with reduction in size and costs, and with aptness to transonic wind-tunnel testing. Detailed specifications and schematics are included.

Britcher, C.↗
NASA NTRS1991

Evaluation of electrolytic tilt sensors for wind tunnel model angle-of-attack (AOA) measurements

The results of a laboratory evaluation of three types of electrolytic tilt sensors as potential candidates for model attitude or angle of attack (AOA) measurements in wind tunnel tests are presented. Their performance was also compared with that from typical servo accelerometers used for AOA measurements. Model RG-37 electrolytic tilt sensors were found to have the highest overall accuracy among the three types. Compared with the servo accelerometer, their accuracies are about one order of magnitude worse and each of them cost about two-thirds less. Therefore, the sensors are unsuitable for AOA measurements although they are less expensive. However, the potential for other applications exists where the errors resulting from roll interaction, vibration, and response time are less, and sensor temperature can be controlled.

Wong, Douglas T.↗
NASA NTRS2020

Development of an Aeroservoelastic Model for Gust Load Alleviation of the NASA Common Research Model Wind Tunnel Experiment

As aircraft move to using composite materials as their primary structure they become lighter and more flexible as well. This presents some significant challenges in association with gust load alleviation. In this paper we develop an aeroservoelastic model for use in developing controllers that utilize distributed control surfaces for active gust load alleviation in a set of wind tunnel experiments. The model is based on an preexisting aeroelastic wing tunnel model and compares the baseline functionality to it. We also provide simple full state feedback simulations for the model.

Cramer, Nick↗
NASA NTRS1975

Vector thrust induced lift effects for several ejector exhaust locations on a V/STOL wind tunnel model at forward speed

The results and analysis of aerodynamic force data obtained from a small scale model of a V/STOL research vehicle in a low speed wind tunnel are presented. The analysis of the data includes the evaluation of aerodynamic-propulsive lift performance when operating twin ejector nozzles with thrust deflected. Three different types of thrust deflector systems were examined: 90 deg downward deflected nozzle, 90 deg slotted nozzle with boundary layer control, and an externally blown flap configuration. Several nozzle locations were tested, including over and underwing positions. The interference lift of the nacelle and model due to jet exhaust thrust is compared and results show that 90 deg turned nozzles located over the wing (near the trailing edge) produce the largest interference lift increment for an untrimmed aircraft, and that the slotted nozzle located under the wing near the trailing edge (in conjunction with a BLC flap) gives a comparable interference lift in the trimmed condition. The externally blown flap nozzle produced the least interference lift and significantly less total lift due to jet thrust effects.

Sharon, A. D.↗
NASA NTRS1981

Transonic flutter and gust-response tests and analyses of a wind-tunnel model of a torsion-free-wing fighter airplane

The paper reports the results of analytical and exploratory wind-tunnel studies of the transonic flutter and gust response characteristics of a 1/5.5-size complete-airplane version of a torsion-free-wing (TFW) fighter aircraft. The critical flutter mode for the TFW-free configuration was found to occur at M = 0.95 and had the rigid-TFW pitch mode as its apparent aerodynamic driver. However, the minimum dynamic flutter for the TFW-free case was only about 20% lower than for the TFW-locked; therefore the present TFW is a viable design concept with respect to flutter. The present TFW was not effective as a gust alleviator.

Ruhlin, C. L.↗
NASA NTRS1992

Propulsion simulator for magnetically suspended wind tunnel models

Simulation of propulsion induced aerodynamic forces and moments, which arise as a result of interactions between propulsive jets and the free stream, is one of the most desired capabilities in magnetic suspension wind tunnels. The feasibility of generating exhaust jets of appropriate characteristics onboard magnetically suspended models was examined. Four concepts of remotely operated propulsion simulators was considered. Three conceptual designs involving conventional technologies such as compressed gas cylinders, liquid monopropellants, and solid propellants were developed. The fourth concept, a laser assisted thruster, which can potentially simulate both inlet and exhaust flows, was found to require very high power levels. The measurement of aerodynamic forces and/or moments were demonstrated, including the effects of exhaust jets, in MSBS wind tunnels. Two propulsion simulator models were developed, a small scale and a large scale unit, both using compressed, liquified CO2 as propellant. Results of the wind tunnel tests with the small scale simulator are discussed.

Joshi, P. B.↗