Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND TUNNEL WALL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

CAST-10-2/DOA 2 Airfoil Studies Workshop Results

During the period of September 23 through 27, 1988, the Transonic Aerodynamics Division at the Langely Research Center hosted an International Workshop on CAST-10-2/DOA 2 Airfoil Studies. The CAST-10 studies were the outgrowth of several cooperative study agreements among the NASA, the NAE of Canada, the DLR of West Germany, and the ONERA of France. Both theoretical and experimental CAST-10 airfoil results that were obtained form an extensive series of tests and studies, were reviewed. These results provided an opportunity to make direct comparisons of adaptive wall test section (AWTS) results from the NASA 0.3-meter Transonic Cryogenic Tunnel and ONERA T-2 AWTS facilities with conventional ventilated wall wind tunnel results from the Canadian high Reynolds number two-dimensional test facility. Individual papers presented during the workshop are included.

Ray, Edward J.↗
NASA NTRSDate not supplied

In-Tunnel Simulations of the NASA Juncture Flow Model

The effect of wind tunnel walls on the development of flow separation in the wing-fuselage juncture area is assessed using FUN3D’s overset and wind tunnel controller capabilities. The simulation data obtained from the in-tunnel runs are compared with the free-air simulations. The simulation results are also evaluated using measurements from the Juncture Flow Experiment.

Nash'at N. Ahmad↗
NASA NTRS1984

Wall pressure measurements for three-dimensional transonic tests

An experiment is described that provides input data for wind-tunnel wall interference assessment methods that are based on test-section wall pressure distributions. Wall pressures have been measured along orifice rows on the test-section walls during longitudinal force tests on two model sizes of the same configuration. These data were acquired at Mach numbers between 0.60 and 0.90 in a small, atmospheric transonic wind tunnel. A sample of the data and a discussion of results are presented.

Sewall, W. G.↗
NASA NTRS1993

Determination of solid/porous wall boundary conditions from wind tunnel data for computational fluid dynamics codes

A computational and experimental study has been undertaken to investigate methods of modeling solid and porous wall boundary conditions in CFD codes. The procedure utilizes experimental measurements at the walls to develop a flow field solution based on the method of singularities. This flow field solution is then imposed as a boundary condition in a CFD simulation of the internal flow field. The effectiveness of this method in describing the boundary conditions at the wind tunnel walls using only sparse experimental measurements has been investigated. Verification of the approach using computational studies has been carried out using an incompressible flow solver. The current work demonstrates this technique for low speed flows and compares the result with experimental data obtained from a heavily instrumented variable porosity test section. Position and refinement of experimental measurements required to describe porous wall boundary conditions has also been considered for application to other porous wall wind tunnels.

Beutner, Thomas J.↗
NASA NTRS1973

Wind tunnel interference factors for high-lift wings in closed wind tunnels

A problem associated with the wind tunnel testing of very slow flying aircraft is the correction of observed pitching moments to free air conditions. The most significant effects of such corrections are to be found at moderate downwash angles typical of the landing approach. The wind tunnel walls induce interference velocities at the tail different from those induced at the wing, and these induced velocities also alter the trajectory of the trailing vortex system. The relocated vortex system induces different velocities at the tail from those experienced in free air. The effect of the relocated vortex and the walls is to cause important changes in the measured pitching moments in the wind tunnel.

Joppa, R. G.↗
NASA NTRS1984

Two- and three-dimensional model and wall data from a flexible-walled transonic test section

Both two- and three-dimensional model testing is being carried out in the transonic flexible-walled wind tunnel test section. The test section has flexible top and bottom walls with rigid sidewalls. Interference is eliminated by adjustments based on data taken at walls in two dimensional models. Cast-7 data will illustrate agreement between various flexible-walled tunnels. In three-dimensional models interference cannot be eliminated but wall adjustments can control and relieve the principal sources of wall-induced errors. Estimates of magnitudes of the control which may be exercised on flow by movement of one wall jack are presented. A wall control algorithm (still in analytic development stage) based on use of this data is described. Brief examples of control of wall-induced perturbations in region of model are given.

Goodyer, M. J.↗
NASA NTRS1993

A wall interference assessment/correction system

A Wall Signature method originally developed by Hackett was selected to be adapted for the Ames 12-ft Wind Tunnel Wall Interference Assessment/Correction (WIAC) System in the project. This method uses limited measurements of the static pressure at the wall, in conjunction with the solid wall boundary condition, to determine the strength and distribution of singularities representing the test article. The singularities are used in turn for estimating wall interference at the model location. The lifting interference will be treated separately by representing in a horseshoe vortex system for the model's lifting effects. The development and implementation of a working prototype will be completed, delivered, and documented with a software manual. The WIAC code will be validated by conducting numerically simulated experiments rather than actual wind tunnel experiments. The simulations will be used to generate both free-air and confined wind-tunnel flow fields for each of the test articles over a range of test configurations. Specifically, the pressure signature at the test section wall will be computed for the tunnel case to provide the simulated 'measured' data. These data will serve as the input for the WIAC method - Wall Signature method. The performance of the WIAC method then may be evaluated by comparing the corrected parameters with those for the free-air simulation. The following two additional tasks are included in the supplement No. 1 to the basic Grant. On-line wall interference calculation: The developed wall signature method (modified Hackett's method) for Ames 12-ft Tunnel will be the pre-computed coefficients which facilitate the on-line calculation of wall interference; and support system effects estimation: The effects on the wall pressure measurements due to the presence of the model support systems will be evaluated.

Lo, Ching F.↗
NASA NTRS1982

Similarity rules for effects of sidewall boundary layer in two-dimensional wind tunnels

A simple analysis of the interaction of the model pressure field with the boundary layer on an unventilated wind tunnel wall is presented. It is shown that the effects of this interaction are similar to compressibility effects for sidewall boundary layers in two dimensional wind tunnels. This similarity is used to derive modified forms of the Prandtl Glauert rule for subsonic flow and the von Karman rule for transonic flow which are validated by comparison with experimental data. The three dimensional interaction problem is discussed, and it is shown that model pressure field/wall boundary layer interaction effects are not similar to compressibility effects in three dimensional wind tunnels.

Barnwell, R. W.↗
NASA NTRS2016

Using RotCFD to Predict Isolated XV-15 Rotor Performance

Experimental techniques to measure rotorcraft aerodynamic performance are widely used. However, the need exists to understand the limitations of ground based testing by augmenting the analysis of experimental test results with Computational Fluid Dynamics (CFD) modeling. The immediate objective of the present research is to develop an XV-15 Tilt Rotor Research Aircraft rotor model for investigation of wind tunnel wall interference. The predicted performance of the XV-15 during various flight modes is compared to theoretical and experimental data. This research is performed to support wind tunnel tests scheduled for 2016. A mid-fidelity RANS solver, RotCFD, is used with an unsteady, incompressible flow model and a realizable k- turbulence model. The rotor is modeled using an actuator disk model or blade element model with a momentum source approach. In RotCFD the setup, grid generation and running of cases is faster than many CFD codes which makes it a useful engineering tool. Performance predictions need not be as accurate as high-fidelity CFD codes, as long as wall effects can be properly simulated. Being able to accurately predict unsteady rotorcraft performance on desktop-class computers provides a quicker analysis of highly complex flows during the initial design phase.

CFD↗
NASA NTRS1975

Development of minimum correction wind tunnels

Flow distortions due to wind tunnel wall interference may be accounted for if the model to tunnel ratio is small, but the theory becomes less reliable as the model becomes larger. This paper presents theoretical analysis and experimental evidence which supports a new concept of wind tunnel. The method employs active control of flow through the walls so that the model is in approximately free air conditions during the test. Practical considerations in the design of such a tunnel are presented. Results indicate that a minimum correction wind tunnel may be achieved with active walls of relatively low porosity.

Bernstein, S.↗
NASA NTRSDate not supplied

Comparison of the CHARM Predictions of the Multirotor Test Bed with Wind Tunnel Experimental Results

Urban air mobility as a fast transportation solution has captured the attention of private companies and government aviation departments in the 21st century. New designs of aerial vehicles are being developed to meet industry needs but often neglect the aerodynamic characteristics and the effects of interacting rotors. This work focuses on predicting rotor behavior and understanding the importance of the rotor wake interaction for future urban air mobility (UAM) designs. The Multirotor Test Bed (MTB) project was initiated at NASA Ames Research center to support the NASA Revolutionary Vertical Lift Technology Project to study rotorcraft performance specifically for multirotor aircraft. The MTB is a modular multirotor test stand that makes testing feasible for up to six rotors at different angles and rotor arrangements, including Tall and Short configurations at different horizontal and vertical rotor separation distances. The MTB was tested in the U.S Army’s 7-by 10-Foot Wind Tunnel at NASA Ames Research Center in late 2019. This work focuses on exploring the impact of aerodynamic interactions between the MTB rotors using the Comprehensive Hierarchical Aeromechanics Rotorcraft Model (CHARM) software. The CHARM software is capable of modeling Vertical Take Off and Landing aircraft aerodynamics in maneuvering and steady flight conditions. CHARM allows the user to define flow and body characteristics, including the rotor geometry, aerodynamic conditions, wind tunnel speed, and airfoil tables as inputs. As the first step, a single MTB rotor was simulated in hover, and the results were compared with wind tunnel test data to confirm the CHARM parameters. Once the accurate performance was verified, the MTB rotors were simulated in forward flight, and each rotor was trimmed to the measured thrust. The simulation variables include one, two, four, and six rotors at the Short and Tall configurations, with MTB pitch angles of 0, -5, and -10 degrees. The MTB was simulated with and without wind tunnel walls. These results demonstrate the rotor wake interaction and its impact on rotor performance. This information also helps determine which configurations should be explored for future wind tunnel tests.

CHARM Predictions↗
NASA NTRS1986

Recent advances in aerodynamics

Papers are presented on unsteady transonic aerodynamics and aeroelasticity, the unsteady separation phenomenon, and a wind tunnel method for V/STOL testing. Also considered are vortex-edge interactions, jet instability theory, large-scale organized motions in jets and shear layers, and the evolution of adaptive-wall wind tunnels. Other topics include advances in ejector thrust augmentation, multiple jet impingement flowfields, and recent advances in prediction methods for jet-induced effects on V/STOL aircraft.

Krothapalli, A.↗
NASA NTRS1944

The Wall Interference of a Wind Tunnel of Elliptic Cross Section

The wall interference is obtained for a wind tunnel of elliptic section for the two cases of closed and open working sections. The approximate and exact methods used gave results in practically good agreement. Corresponding to the result given by Glauert for the case of the closed rectangular section, the interference is found to be a minimum for a ratio of minor to major axis of 1:square root of 6 This, however, is true only for the case where the span of the airfoil is small in comparison with the width of the tunnel. For a longer airfoil the favorable ellipse is flatter. In the case of the open working section the circular shape gives the minimum interference.

Tani, Itiro↗
NASA NTRS1980

Calculations of transonic flow about an airfoil in a wind tunnel

A combined experimental and numerical study was performed to include wind-tunnel wall interference effects in calculations for airfoil flows at transonic speeds. Pressure-survey-tube and laser-Doppler velocimeter measurements were made in the flow field about an airfoil in the 2- by 2-Foot Transonic Wind Tunnel at Ames Research Center. The results were then used as boundary data in a Navier-Stokes code modified by incorporating a pressure condition on the upper and lower computational boundaries. Comparison of calculated results and experimental data obtained from the surface of the airfoil indicates that the pressure-boundary condition is particularly effective in moving the shock to a position near that observed experimentally when the flow remains attached. For flows with large separation, shock position and viscous-layer properties are not well predicted, principally because of the inadequacies of the algebraic turbulence models employed with the method.

King, L. S.↗
NASA NTRS1994

Evaluation of the prototype dual-axis wall attitude measurement sensor

A prototype dual-axis electrolytic tilt sensor package for angular position measurements was built and evaluated in a laboratory environment. The objective was to investigate the use of this package for making wind tunnel wall attitude measurements for the National Transonic Facility (NTF) at NASA Langley Research Center (LaRC). The instrumentation may replace an existing, more costly, and less rugged servo accelerometer package (angle-of-attack package) currently in use. The dual-axis electrolytic tilt sensor package contains two commercial electrolytic tilt sensors thermally insulated with NTF foam, all housed within a stainless steel package. The package is actively heated and maintained at 160 F using foil heating elements. The laboratory evaluation consisted of a series of tests to characterize the linearity, repeatability, cross-axis interaction, lead wire effect, step response, thermal time constant, and rectification errors. Tests revealed that the total RMS errors for the x-axis sensor is 0.084 degree, and 0.182 degree for the y-axis sensor. The RMS errors are greater than the 0.01 degree specification required for NTF wall attitude measurements. It is therefore not a viable replacement for the angle-of-attack package in the NTF application. However, with some physical modifications, it can be used as an inexpensive 5-degree range dual-axis inclinometer with overall accuracy approaching 0.01 degree under less harsh environments. Also, the data obtained from the tests can be valuable for wind tunnel applications of most types of electrolytic tilt sensors.

Wong, Douglas T.↗
NASA NTRS2011

Axisymmetric Calculations of a Low-Boom Inlet in a Supersonic Wind Tunnel

This paper describes axisymmetric CFD predictions made of a supersonic low-boom inlet with a facility diffuser, cold pipe, and mass flow plug within wind tunnel walls, and compares the CFD calculations with the experimental data. The inlet was designed for use on a small supersonic aircraft that would cruise at Mach 1.6, with a Mach number over the wing of 1.7. The inlet was tested in the 8-ft by 6-ft Supersonic Wind Tunnel at NASA Glenn Research Center in the fall of 2010 to demonstrate the performance and stability of a practical flight design that included a novel bypass duct. The inlet design is discussed here briefly. Prior to the test, CFD calculations were made to predict the performance of the inlet and its associated wind tunnel hardware, and to estimate flow areas needed to throttle the inlet. The calculations were done with the Wind-US CFD code and are described in detail. After the test, comparisons were made between computed and measured shock patterns, total pressure recoveries, and centerline pressures. The results showed that the dual-stream inlet had excellent performance, with capture ratios near one, a peak core total pressure recovery of 96 percent, and a large stable operating range. Predicted core recovery agreed well with the experiment but predicted bypass recovery and maximum capture ratio were high. Calculations of offdesign performance of the inlet along a flight profile agreed well with measurements and previous calculations.

Chima, Rodrick V.↗