SEARCH · Search NASA

Results for “WINGS, RECTANGULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Unsteady transonic aerodynamics and aeroelastic calculations at low-supersonic freestreams

A computational procedure is presented to simulate transonic unsteady flows and corresponding aeroelasticity of wings at low-supersonic freestreams. The flow is modeled by using the transonic small-perturbation theory. The structural equations of motions are modeled using modal equations of motion directly coupled with aerodynamics. Supersonic freestreams are simulated by properly accounting for the boundary conditions based on pressure waves along the flow characteristics in streamwise planes. The flow equations are solved using the time-accurate, alternating-direction implicit finite-difference scheme. The coupled aeroelastic equations of motion are solved by an integration procedure based on the time-accurate, linear-acceleration method. The flow modeling is verified by comparing calculations with experiments for both steady and unsteady flows at supersonic freestreams. The unsteady computations are made for oscillating wings. Comparisons of computed results with experiments show good agreement. Aeroelastic responses are computed for a rectangular wing at Mach numbers ranging from subtransonic to upper-transonic (supersonic) freestreams. The extension of the transonic dip into the upper transonic regime is illustrated.

Guruswamy, Guru P.↗

NASA NTRS1939

Airfoil Theory at Supersonic Speed

A theory is developed for the airfoil of finite span at supersonic speed analogous to the Prandtl airfoil theory of 1918-1919 for incompressible flow. In addition to the profile and induced drags, account must be taken at supersonic flow of still another drag, namely, the wave drag, which is independent of the wing aspect ratio. Both wave and induced drags are proportional to the square of the lift and depend on the Mach number, that is, the ratio of flight to sound speed. In general, in the case of supersonic flow, the drag-lift ratio is considerably less favorable than is the case for incompressible flow. Among others the following examples are considered: 1) lifting line with constant lift distribution (horseshoe vortex); 2) computation of wave and induced drag and the twist of a trapezoidal wing of constant lift density; 3) computation of the lift distribution and drag of an untwisted rectangular wing.

Schlichting, H↗

NASA NTRS1941

Wind-Tunnel Investigation of an NACA 66,2-216 Low-Drag Wing with Split Flaps of Various Sizes, Special Report

An investigation was conducted in the NACA 19-foot pressure wind tunnel of a rectangular wing having NACA 66, 2-216 low-drag airfoil sections and various sizes of simple split flaps. The purpose of the investigation was, primarily, to determine the influence of these flap installations on the aerodynamic characteristics of the wing. Complete lift, drag, and pitching-moment characteristics were determined for a range of test Reynolds numbers from about 2,600,000 to 4,600,000 for each of the installations and for the plain wing. The results of this investigation indicate that values of maximum lift coefficient similar to those of wings with conventional airfoil sections and split flaps can be expected of wings having the NACA 66,2-216 low-drag sections. The increment of maximum lift due to the split flap was found to be practically independent of the Reynolds number over the range investigated. The optimum split flap on the basis of maximum lift appears to have a chord about 20% of the wing chord and a deflection of 60 degrees. The C(sub L) max of the wing with the 0.20c partial-span flap deflected 60 degrees is 2.07 at a Reynolds number of 4,600,000 while with the full-span flap it is approximately 2.53; the increment of the maximum lift coefficient due to the flap is approximately proportional to the flap span. Although the addition of a split flap tends to hasten the stall and to cause it to occur more abruptly, little change in pattern is evidenced by observations of the behavior of wool tufts on the wing.

Muse, Thomas C.↗

NASA NTRS1976

Unsteady flow past wings having sharp-edge separation

A vortex-lattice technique is developed to model unsteady, incompressible flow past thin wings. This technique predicts the shape of the wake as a function of time; thus, it is not restricted by planform, aspect ratio, or angle of attack as long as vortex bursting does not occur and the flow does not separate from the wing surface. Moreover, the technique can be applied to wings of arbitrary curvature undergoing general motion; thus, it can treat rigid-body motion, arbitrary wing deformation, gusts in the freestream, and periodic motions. Numerical results are presented for low-aspect rectangular wings undergoing a constant-rate, rigid-body rotation about the trailing edge. The results for the unsteady motion are compared with those predicted by assuming quasi-steady motion. The present results exhibit hysteretic behavior.

Atta, E. H.↗

NASA NTRS1949

On the Installation of Jet Engine Nacelles on a Wing Fourth Partial Report: Pressure-Distribution Measurements on a Sweptback Wing with Jet Engine Nacelle

The present report, which deals with pressure-distribution measurements made on a sweptback wing with a jet engine nacelle, is similar to a report on pressure-distribution measurements on a rectangular wing with a jet engine nacelle (second partial report). Here, in investigations preliminary to high-speed measurements, as in the second partial report, useful arrangements and fillet designs have been discovered.

Buschner, R.↗

NASA NTRS1984

Development and applications of algorithms for calculating the transonic flow about harmonically oscillating wings

A finite difference method to solve the unsteady transonic flow about harmonically oscillating wings was investigated. The procedure is based on separating the velocity potential into steady and unsteady parts and linearizing the resulting unsteady differential equation for small disturbances. The differential equation for the unsteady velocity potential is linear with spatially varying coefficients and with the time variable eliminated by assuming harmonic motion. An alternating direction implicit procedure was investigated, and a pilot program was developed for both two and three dimensional wings. This program provides a relatively efficient relaxation solution without previously encountered solution instability problems. Pressure distributions for two rectangular wings are calculated. Conjugate gradient techniques were developed for the asymmetric, indefinite problem. The conjugate gradient procedure is evaluated for applications to the unsteady transonic problem. Different equations for the alternating direction procedure are derived using a coordinate transformation for swept and tapered wing planforms. Pressure distributions for swept, untaped wings of vanishing thickness are correlated with linear results for sweep angles up to 45 degrees.

Ehlers, F. E.↗

NASA NTRS1988

Computational technique for compressible vortex flows using the integral equation solution

The steady full-potential equation is written in the form of Poisson's equation, and the solution for the velocity field is expressed in terms of an integral equation. The integral solution consists of two surface integrals and one volume integral. The solution is obtained through successive iteration cycles. Each cycle of iteration consists of two sub-cycles, an inner cycle for wake relaxation and an out cycle for the strength of the source distribution integrals representing the flow compressibility. The density gradients in the source distribution is computed by using a type-differencing scheme of the Murman-Cole type. The method is applied to delta wings and the numerical examples show that a curved shock is captured on the wing suction side beneath the leading edge vortex sheet. Recently, a modified version of the scheme was applied to rectangular wings. In this modified scheme, the surface integral terms were computed by using a bilinear distribution of vorticity on triangular vortex panels which represent the wing and its wake. The results were compared with the available experimental data and they are in good agreement.

Kandil, Osama A.↗

NASA NTRS1976

A finite element solution of unsteady transonic flow problems for three-dimensional wings and bodies

A computerized finite element method has been developed to solve a form of the three-dimensional inviscid, irrotational unsteady transonic equation for pointed and rectangular wings and wing-body combinations. The equation is a 'parabolized' version of the full unsteady transonic equation which includes the effect of the advancing wave and the acceleration in the steady flow field thus including a thickness effect. Automatic mesh generation using conformal mapping has the advantage of allowing relatively arbitrary cross-sections to be closely approximated while taking advantage of the body's similarity to a more simple configuration. Plunge, pitch, and roll modes are computed

Kimble, K. R.↗

NASA NTRS1972

Wind tunnel test data for wing trailing vortex flow survey

Data are presented on velocity measurements made with hot wire anemometers in the wake of a model of the CV-990 aircraft and a rectangular wing in the NASA-Ames 2.14x3.05 meter (7- by 10-foot) wind tunnels. Variables included angle of attack, tunnel speed and axial distance up to 12 chord lengths downstream from the wing trailing edge. Effects of deflecting trailing edge flaps and small spoiler panels are shown.

Chigier, N. A.↗

NASA NTRS1976

Sample wings for study

Two simple wings were selected for study using the various implementations (old and new) of the vortex lattice method. These are: (1) a rectangular wing with an aspect ratio of 2, and (2) a tapered wing with an aspect ratio of 5, a taper ratio of 0.5, a leading sweep of 3.317 deg., and a trailing edge sweep of 1-11.308 deg. This was done in order to gain an appreciation for the accuracy of the various implementations. References were given where force, moment, and pressure data could be found for these wings.

Lamar, J. E.↗

NASA NTRS1961

Aerodynamic Characteristics of Low-Aspect-Ratio Wings in Close Proximity to the Ground

A wind-tunnel investigation has been conducted to determine the effect of ground proximity on the aerodynamic characteristics of thick highly cambered rectangular wings with aspect ratios of 1. 2, 4, and 6. The results showed that, for these aspect ratios, as the ground war, approached all wings experienced increases in lift-curve slope and reductions in induced drag which resulted in increases in lift-drag ratio. Although an increase in lift-curve slope was obtained for all aspect ratios as the ground was approached, the lift coefficient at an angle of attack of 0 deg for any given aspect ratio remained nearly constant. The experimental results were in general agreement with Wieselsberger's ground-effect theory (NACA Technical Memorandum 77). As the wings approached the ground, there was an increase in static longitudinal stability at positive angles of attack. When operating in ground effect, all the wings had stability of height at positive angles of attack and instability of height at negative angles of attack. Wing-tip fairings on the wings with aspect ratios of 1 and 2 produced small increases in lift-drag ratio in ground effect. End plates extending only below the chord plane on the wing with an aspect ratio of 1 provided increases in lift coefficient and in lift-drag ratio in ground effect.

Fink, Marvin P.↗

NASA NTRS2016

Unsteady Aerodynamic Force Sensing from Measured Strain

A simple approach for computing unsteady aerodynamic forces from simulated measured strain data is proposed in this study. First, the deflection and slope of the structure are computed from the unsteady strain using the two-step approach. Velocities and accelerations of the structure are computed using the autoregressive moving average model, on-line parameter estimator, low-pass filter, and a least-squares curve fitting method together with analytical derivatives with respect to time. Finally, aerodynamic forces over the wing are computed using modal aerodynamic influence coefficient matrices, a rational function approximation, and a time-marching algorithm. A cantilevered rectangular wing built and tested at the NASA Langley Research Center (Hampton, Virginia, USA) in 1959 is used to validate the simple approach. Unsteady aerodynamic forces as well as wing deflections, velocities, accelerations, and strains are computed using the CFL3D computational fluid dynamics (CFD) code and an MSC/NASTRAN code (MSC Software Corporation, Newport Beach, California, USA), and these CFL3D-based results are assumed as measured quantities. Based on the measured strains, wing deflections, velocities, accelerations, and aerodynamic forces are computed using the proposed approach. These computed deflections, velocities, accelerations, and unsteady aerodynamic forces are compared with the CFL3D/NASTRAN-based results. In general, computed aerodynamic forces based on the lifting surface theory in subsonic speeds are in good agreement with the target aerodynamic forces generated using CFL3D code with the Euler equation. Excellent aeroelastic responses are obtained even with unsteady strain data under the signal to noise ratio of -9.8dB. The deflections, velocities, and accelerations at each sensor location are independent of structural and aerodynamic models. Therefore, the distributed strain data together with the current proposed approaches can be used as distributed deflection, velocity, and acceleration sensors. This research demonstrates the feasibility of obtaining induced drag and lift forces through the use of distributed sensor technology with measured strain data. An active induced drag control system thus can be designed using the two computed aerodynamic forces, induced drag and lift, to improve the fuel efficiency of an aircraft. Interpolation elements between structural finite element grids and the CFD grids and centroids are successfully incorporated with the unsteady aeroelastic computation scheme. The most critical technology for the success of the proposed approach is the robust on-line parameter estimator, since the least-squares curve fitting method depends heavily on aeroelastic system frequencies and damping factors.

shape sensing↗

NASA NTRS1977

Aerodynamics of a finite aspect ratio jet flap at low flight speeds

A theoretical treatment of inviscid incompressible flow over a thin wing equipped with a part-span jet flap is given; the treatment is capable of describing low-speed flight regimes where nonlinear problems may be significant. The induced flow fields of the jet and the wing are characterized separately, and a fully coupled solution is reached through iteration. A lifting surface theory is employed for the wing aerodynamics, and the vorticity associated with the jet is also taken into account. Calculations are presented for the case of a rectangular wing. Comparisons with existing linear or nonlinear theories and experimental data suggest that the treatment is capable of accurate analyses in situations involving small angles of attack, jet deflection angles and jet momentum coefficients. In addition, the theory may be a better means of evaluating subsidiary aerodynamic variables, such as downwash aft of the wing, than existing treatments.

Addessio, F. L.↗

NASA NTRS1987

Euler calculations for wings using Cartesian grids

A method is presented for the calculation of transonic flows past wings using Cartesian grids. The calculations are based on a finite volume formulation of the Euler equations. Results are presented for a rectangular wing with a flat tip and the ONERA M6 wing. In general, the results are in good agreement with other computations and available experiment. However, Cartesian grids require a greater number of points than body fitted grids in order to resolve the flow properties near the leading edge of a swept wing.

Gaffney, R. L., Jr.↗

NASA NTRS1991

Experimental study of an independently deflected wingtip mounted on a semispan wing

The results of a subsonic wind tunnel test of a semispan wing with an independently deflected tip surface are presented and analyzed. The tip surface was deflected about the quarter chord of the rectangular wing and accounted for 17 percent of the wing semispan. The test was conducted to measure the loads on the tip surface and to investigate the nature of aerodynamic interference effects between the wing and the deflected tip. Results are presented for two swept tip surfaces of similar planform but different airfoil distributions. The report contains plots of tip lift, drag, and pitching moment for various Reynolds numbers and tip deflection angles with respect to the inboard wing. Oil flow visualization photographs for a typical Reynolds number are also included. Important aerodynamic parameters such as lift and pitching moment slopes and tip aerodynamic center location are tabulated. A discussion is presented on the relationship between tip experimental data acquired in a steady flow and the prediction of unsteady tip motion at fixed wing angles of attack.

Martin, D. M.↗

NASA NTRS1994

Measurements of Supersonic Wing Tip Vortices

An experimental survey of supersonic wing tip vortices has been conducted at Mach 2.5 using small performed 2.25 chords down-stream of a semi-span rectangular wing at angle of attack of 5 and 10 degrees. The main objective of the experiments was to determine the Mach number, flow angularity and total pressure distribution in the core region of supersonic wing tip vortices. A secondary aim was to demonstrate the feasibility of using cone probes calibrated with a numerical flow solver to measure flow characteristics at supersonic speeds. Results showed that the numerically generated calibration curves can be used for 4-hole cone probes, but were not sufficiently accurate for conventional 5-hole probes due to nose bluntness effects. Combination of 4-hole cone probe measurements with independent pitot pressure measurements indicated a significant Mach number and total pressure deficit in the core regions of supersonic wing tip vortices, combined with an asymmetric 'Burger like' swirl distribution.

Smart, Michael K.↗

NASA NTRS1989

Some effects of aerodynamic spoilers on wing flutter

The effects of deployment angle and size of symmetrically mounted upper-surface and lower-surface spoilers on the flutter characteristics of a simple, paddle-like, low-aspect-ratio, rectangular wing model that was tested at Mach number 0.80 in the Langley Transonic Dynamics Tunnel are presented. The results show that the flutter dynamic pressure is increased by increasing either spoiler deployment angle or spoiler size. For the configurations studied spoiler size was more effective than deployment angle in increasing the flutter dynamic pressure.

Doggett, Robert V., Jr.↗

DOE OSTI2020

Aeroelastic oscillations of a pitching flexible wing with structural geometric nonlinearities: Theory and numerical simulation

In this paper, we focus on the derivation of an analytical model of the aeroelastic dynamics of an elastically mounted flexible wing. This equations of motion obtained serve to help understand the behaviour of the aeroelastic wind tunnel setup in question, which consists of a rectangular wing with a uniform NACA 0012 airfoil profile, whose base is free to rotate rigidly about a longitudinal axis. Of particular interest are the structural geometric nonlinearities primarily introduced by the coupling between the rigid body pitch degree-of-freedom and the continuous system. A coupled system of partial differential equations (PDEs) coupled with an ordinary differential equation (ODE) describing axial-bending-bending-torsion-pitch motion is derived using Hamilton's principle. A finite dimensional approximation of the system of coupled differential equations is obtained using the Galerkin method, leading to a system of coupled nonlinear ODEs. Subsequently, these nonlinear ODEs are solved numerically using Houbolt's method. The results that are obtained are verified by comparison with the results obtained by direct integration of the equations of motion using a finite difference scheme. Adopting a linear unsteady aerodynamic model, it is observed that the system undergoes coalescence flutter due to coupling between the rigid body pitch rotation dominated mode and the first flapwise bending dominated mode. Finally, the behaviour of the limit cycle oscillations is primarily influenced by the structural geometric nonlinear terms in the coupled system of PDEs and ODE.

42 ENGINEERING↗