Search NASA⌕ Search

SEARCH · Search NASA

Results for “Welding Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Development of a Semi-autonomous Miniature Rover for Inspection of Double Shell Tank Floors - 19575

Leaks in the primary liner of double-shell tank (DST) 241-AY-102 at Hanford have prompted the need for the development of inspection tools that are able to access confined spaces around and underneath the tanks. Last year, Florida International University (FIU) has continued to improve inspection tools that were developed in the previous years, to ensure that the resultant tools are able to overcome the challenges posed by the DSTs. Experimental testing conducted last year at the full-scale sectional mock-up of the DST's refractory slots revealed some shortcomings of the miniature rover, particularly in traversing over weld seams of different heights. The weld seams are the results of welded steel plate-joints for the DST. It was advised by the site engineers that the weld seams height could range from 6.35 mm - 9.525 mm (1/4 to 3/8 inches), and with 12.7 mm (1/2 inches) width. As the rover traverses over a weld seam, the gap between the rover's magnets and tank surface increases, causing the adhesive force to drop. The rover loses its surface contact if this adhesive force drops below its weight, jeopardizing the inspection tasks. In this paper, we present the numerical studies to calculate the minimum magnetic force required for the miniature rover to traverse over weld seams with different heights and the corresponding modifications to the rover design. Initial bench scale tests were conducted using a steel bar with 5 welds of varying heights. The testing validated the results from the simulation studies and established the rover's capability in traversing weld seams. Another challenge for the miniature rover is the use of a joystick or keypad for manual control. Utilizing these controls will likely be difficult for the operators due to the tight channels underneath the tank. Having a semi-autonomous navigational capability would alleviate the complexity of the inspection tasks and allow the operator to focus on the channel inspection. The goal is to implement lane-keeping capability, akin to that of a driverless car, for the inspection tool, so that it will maintain its relative position with respect to the wall of the channels. Am image processing pipeline has been developed using both the Robot Operating System (ROS) and OpenCV to process the image stream coming from the onboard camera, for the purpose of lane identification. Additionally, a PID controller has been implemented to navigate the miniature rover along the central location of the detected lane, while allowing the operator to control the tool's forward and backward motion. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Postweld Heat Treatment on Toughness of Electric- Resistance Welded X70 Steel

In this report the effect of postweld heat treatment (PWHT) on Charpy V-notch impact toughness of a highfrequency electric-resistance welded (HF-ERW) grade X70 pipeline steel is investigated. PWHT thermal cycles are simulated using the Gleeble on the as-welded specimens. Microstructure, along with crystallographic texture and microhardness, is characterized in specimens that are impact tested at –5°C (23°F), –30°C (–22°F), and –45°C (–49°F). The impact toughness values show a wide scatter band and decrease with the increasing peak temperature of the PWHT. For higher peak temperatures, the microstructure of the heat-affected zone (HAZ) gradually changed from equiaxed ferrite to bainitic ferrite. Furthermore, the prior austenite grain size (PAGS) increases with the increasing peak temperature. The density of high-angle grain boundaries decreases, and the fraction of cleavage planes {100} parallel to the impact fracture plane increases for higher peak temperatures of the PWHT

36 MATERIALS SCIENCE↗

Softening Behavior of Electron Beam Welded 22SiMn2TiB Steel

Softening behavior occurs in heat-affected zone of many types of high strength steels causing the deterioration of mechanical properties. In this study, the softening behavior of 22SiMn2TiB joint was revealed by experimental and numerical analysis. The microstructure and hardness of the joint were tested and analyzed. The numerical simulations of the temperature field were carried out to obtain the thermal cycle. Based on the continuous cooling transformation diagram, the phase transformation was investigated. The results indicated that the microhardness in the HAZ was significantly decreased, and its minimum value was 273 HV which was 63.5% of base metal. The softening behavior occurs in intermediate critical heat-affected zone and the subcritical heat-affected zone, and its peak temperature is between 853.7 °C (Ac{sub 3}) and 450 °C. When 22SiMn2TiB steel was heated above 732.3 °C (Ac{sub 1}), martensite begins to transform into austenite. With different cooling rates, austenite may transform into martensite, bainite and ferrite, and the volume fraction of soft phases could increase resulting in the softening. When the peak temperature is between 732.3 and 450 °C, the recovery phenomenon and the decomposition of martensite caused softening with the decrease in the dislocation density and martensite.

36 MATERIALS SCIENCE↗

2195 Aluminum-Copper-Lithium Friction Plug Welding Development

Technology developments and applications of friction plug welding is presented. This friction repair welding technology is being studied for implementation on the Space Transportation System's Super Light Weight External Tank. Single plug repairs will be used on a vast majority of weld defects, however, linear defects of up to several inches can be repaired by overlapping plug welds. Methods and results of tensile, bend, simulated service, surface crack tension and other tests at room and cryogenic temperatures is discussed. Attempts to implement Friction Plug Welding has led to both tool and process changes in an attempt to minimize expansive tooling and lengthy implementation times. Process control equipment and data storage methods intended for large scale production will also be addressed. Benefits include increased strength and toughness, decreased weld repair time, automated and highly reliable process, and a lower probability of having to re-repair defect locations.

Takeshita, Rike P.↗

Thermal Simulation Analysis of Microstructure and Hardness for CrMoV with PWHT in Type IV Region

Welded components of CrMoV steam pipe exhibit a pernicious form of type IV cracking after long-term service at elevated temperature. To investigate the cracking mechanism, the type IV microstructure and hardness were characterized after thermal simulation of post-weld heat treatment. Below 1098 K (825 °C), loss of carbon from the pearlite region was apparent, and the work zone exhibited a slightly lower hardness than the parent material because of a minor amount of austenite transformation. In addition, for peak temperatures above 1133 K (860 °C), additional transformation into austenite occurred and was followed by retransformation into ferrite upon further increasing the temperature. The pearlite formed at 1173 K to 1223 K (900 °C to 950 °C) resulted in an increase of the volume fraction of pearlite and microstructural refinement, which yielded a remarkable increase of hardness in the work zone. For the peak temperature of 1573 K (1300 °C), previous austenite grains were coarsened and alloy carbides were dissolved in the austenite, which significantly hardened the work zone.

36 MATERIALS SCIENCE↗

Evaluation of Plastic “Eta” Factor for Welds of SS316L(N) with High Strength Mismatch Ratio

Fracture testing standards of ASTM and ISO recommend expressions for plastic η factor of various fracture test specimen geometries to evaluate the fracture behavior of materials. These are intended for homogenous specimens, but according to ISO 15653, it can be extended for weldments up to a strength mismatch ratio (M) of 1.25. In practice, M > 1.25 is encountered in many applications. In the present study, η factor has been evaluated for welded compact tension specimens using a limit load-based approach. The η factors obtained using this approach for homogenous specimens with elastic–perfectly plastic material model are found to be within ± 4% of those from the ASTM E 1820-17a, thereby validating the procedure. For welds, the limit load is obtained from nonlinear (elastic–plastic) FE simulations. η factors for specimens with various crack lengths (a), weld width (h) and strength mismatch have been evaluated and found to be significantly influenced by these parameters. For M > 1.25, the estimated η values were found to be ~ 16% lower compared to that from the ASTM E 1820-17a. Thus, the use of the η values from the proposed method provides a conservative estimate of J–R curve for the welds. Further, it has been observed that depending on the slope of the blunting line, the J{sub Ic} value may vary significantly with the estimated η values.

36 MATERIALS SCIENCE↗

On relationship between microfissuring and microstructure in the HAZ of Inconel 718

Inconel 718, as well as many other metals, is susceptible to intergranular hot cracking in the weld heat-affected-zone (HAZ). These cracks form near the solidus temperature of the metal during the welding process. This problem is of particular concern to NASA/MSFC because the SSME is primarily constructed of welded Inconel 718. The present program studied microfissuring in the weld HAZ of Inconel 718 by simulating HAZ thermal cycles with the Gleeble machine. Previous researchers have studied the instantaneous mechanical properties of the HAZ using the Gleeble. The present study examines the instantaneous microstructure of the HAZ. This approach showed that second phase structures, high in niobium, melt and wet the grain boundaries in the HAZ during welding. It is postulated that the resultant HAZ grain boundaries, enriched in niobium, act as preferred sites for microfissure nucleation as the weld zone cools.

Thompson, R. G.↗

Weldability of HAYNES 282 alloy for new fabrications and after service exposure

The effect of alloying elements on the mechanical properties and weldability of wrought gamma prime strengthened nickel based superalloys is well known. An understanding of the basic guidelines concerning alloying additions has led to the invention and development of HAYNES 282 alloy for applications in aircraft and land based gas turbines and other high performance high temperature environments. The alloy combines exceptional high temperature properties with good weldability and fabricability. At high temperatures (?900 >C), the alloy is stronger in creep strength than Waspaloy alloy (UNS N07001) and it approaches the creep strength of R-41 alloy (UNS N07041). Because the alloy has better thermal stability, fabricability and weldability than Waspaloy and R-41 alloys, it is currently being considered as a candidate universal consumable for welding/repair welding of gamma prime strengthened nickel based superalloys and it is also being considered as a suitable replacement for applications where R-41, Waspaloy and C263 (UNS N07263) alloys are currently being used. The alloy was designed to have improved resistance to strain age cracking, a problem common to gamma prime strengthened nickel based superalloys. In this paper, the results from time resolved X-ray diffraction studies during a welding thermal cycle; gas metal arc welding of thick and gas tungsten arc welding of thin section annealed material (for new fabrications) and annealed and aged material (welding under the aged/service exposed condition); and the results from heat affected zone physical simulations of the weldment measured 2 mm from the weld centreline of annealed (for new fabrication) and annealed and aged (service exposed) material will be presented. Creep properties (870 C/159 MPa) of the weldment will be discussed as well as mechanisms leading to failure.

White, H↗

Experimental determination of the complex stiffness tensor and Euler angles in anisotropic media using ultrasonic waves

The aim of this work is to measure the complex elastic tensor and Euler angles in very complex anisotropic media like austenitic steel welds, by inverse problem resolution from experimental data. The obtained experimental characteristics of the anisotropic material will be injected in a FE code developed by EDF enabling the simulation of an actual ultrasonic NDE of welds. The present work aims to provide reliable input data to the 3D future development of the code. In particular, this complex elastic tensor will allow to predict by modeling beam skewing ant attenuation in an austenitic weld. The investigation of such anisotropic media is very complex because of the directional dependency of the elastic stiffness tensor. Then we will discuss the use of a hybrid genetic algorithm to overcome this difficulty. The identification method is based on waveforms spectra reconstruction associated to a physical model describing wave propagation in plates, during underwater measurements. The entire procedure is qualified and validated using simulated data. Moreover, a comparison of the estimated elastic coefficients with literature values and ultrasonic measurements obtained in transmission is also given, at the end of the paper.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Thermoplastic Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗

Thermoplastic Composite Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗

NASA welding assessment program

A program was conducted to demonstrate the cycle life capability of welded solar cell modules relative to a soldered solar cell module in a simulated low earth orbit thermal environment. A total of five 18-cell welded (parallel gap resistance welding) modules, three 18-cell soldered modules, and eighteen single cell samples were fabricated using 2 x 4 cm silicon solar cells from ASEC, fused silica cover glass from OCLI, silver plated Invar interconnectors, DC 93-500 adhesive, and Kapton-Kevlar-Kapton flexible substrate material. Zero degree pull strength ranged from 2.4 to 5.7 lbs for front welded contacts (40 samples), and 3.5 to 6.2 lbs for back welded contacts (40 samples). Solar cell cross sections show solid state welding on both front and rear contacts. The 18-cell welded modules have a specific power of 124 W/kg and an area power density of 142 W/sq m (both at 28 C). Three welded and one soldered module were thermal cycle tested in a thermal vacuum chamber simulating a low earth orbit thermal environment.

Patterson, R. E.↗

XFEM Development for Modeling Crack Growth in Prototypical Welded Components

Nuclear power plant components are subjected to harsh operating environments that can lead to multiple degradation mechanisms in which fracture can play a prominent role. Predicting crack growth is important for assessing the integrity of welded components. The extended finite element method (XFEM) is an important tool for modeling such crack growth, and XFEM capabilities have been developed within the MOOSE framework. This report documents work in the MOOSE XFEM module to model fractures in three-dimensional representations of components using a topologically two-dimensional mesh to define cutting planes. Crack growth algorithms have been implemented to evolve the cutting mesh based on equations for stress corrosion cracking. Additionally, several usability and robustness improvements have been developed to enable three-dimensional fracture simulations. The cutting algorithms were demonstrated on a three-dimensional model of a prototypical reactor component undergoing stress corrosion cracking driven by idealized weld residual stresses. This is an incremental step toward using this capability to model more complex components with residual stresses computed through welding process simulations.

42 - ENGINEERING↗

Dynamic control of robotic welding - On-going research

Two major challenges exist for the development of dynamic control systems: first, the control system must be resourceful enough to provide problem-solving capabilities in unforeseen circumstances; second, it must be rapid enough to respond to dynamic environments. Most conventional control systems do not have the ability to 'step back' and problem-solve, especially in environments with incomplete and uncertain models and data. Orthogonally, commercially available AI systems usually do not respond at the rates required to support 'real-time' control. Hence, control systems are not available that respond to complex dynamic environments within appropriate time constraints. This paper describes work on an AI-based control system designed to address these challenges. A prototype system has been used, in a simulated environment, to control the robotic welding of aerospace components. This AI-based control system has demonstrated the ability to flexibly control a complex process within required time constraints by incorporating higher level reasoning and the ability to deal with uncertainty. Further work is in progress to expand the system's problem-solving capabilities.

Ruokangas, Corinne C.↗

Quasi-Distributed Fiber Sensor-Based Approach for Pipeline Health Monitoring: Generating and Analyzing Physics-Based Simulation Datasets for Classification

This study presents a framework for detecting mechanical damage in pipelines, focusing on generating simulated data and sampling to emulate distributed acoustic sensing (DAS) system responses. The workflow transforms simulated ultrasonic guided wave (UGW) responses into DAS or quasi-DAS system responses to create a physically robust dataset for pipeline event classification, including welds, clips, and corrosion defects. This investigation examines the effects of sensing systems and noise on classification performance, emphasizing the importance of selecting the appropriate sensing system for a specific application. The framework shows the robustness of different sensor number deployments to experimentally relevant noise levels, demonstrating its applicability in real-world scenarios where noise is present. Overall, this study contributes to the development of a more reliable and effective method for detecting mechanical damage to pipelines by emphasizing the generation and utilization of simulated DAS system responses for pipeline classification efforts. The results on the effects of sensing systems and noise on classification performance further enhance the robustness and reliability of the framework.

36 MATERIALS SCIENCE↗

Structural Performance Evaluation of Composite-To-Steel Weld Bonded Joint

The Automotive Composites Consortium (ACC), a collaboration of Chrysler, Ford, General Motors, and the US Department of Energy is conducting a focal project to demonstrate the use of composite materials in high volume structural applications such as an underbody capable of carrying crash loads. One of the critical challenges is to attach the composite part to the steel structure in a high-volume automotive manufacturing environment and meet the complex requirements for crash. Weld-bonding, a combination of adhesive bonding and spot welding, was selected as the primary joining method. A novel concept of bonding doubler steel strips to composite enabled the spot welding to the steel structure, ensuring the compability with the OEM assembly processes. The structural performance of the joint, including durability, was assessed via analytical and physical testing under quasi-static loading at various temperatures. This paper discusses the results of the experiments designed to generate key modeling parameters for Finite Element Analysis of the joint.

36 MATERIALS SCIENCE↗

Experimental and numerical modeling of heat transfer in directed thermoplates

We present three-dimensional numerical simulations to quantify the design specifications of a directional thermoplate expanded channel heat exchanger, also called dimpleplate. Parametric thermofluidic simulations were performed independently varying the number of spot welds, the diameter of the spot welds, and the thickness of the fluid channel within the laminar flow regime. Results from computational fluid dynamics simulations show an improvement in heat transfer is achieved under a variety of conditions: when the thermoplate has a relatively large cross-sectional area normal to the flow, a ratio of spot weld spacing to channel length of 0.2, and a ratio of the spot weld diameter with respect to channel width of 0.3. Lastly, experimental results performed to validate the model are also presented.

14 SOLAR ENERGY↗

Influence of Welding Strength Matching Coefficient and Cold Stretching on Welding Residual Stress in Austenitic Stainless Steel

Austenitic stainless steel is widely used in pressure vessels for the storage and transportation of liquid gases such as liquid nitrogen, liquid oxygen, and liquid hydrogen. Cryogenic pressure vessel manufacturing uses cold stretching technology, which relies heavily on welding joint performance, to construct lightweight and thin-walled vessels. Residual stress from welding is a primary factor in cases of austenitic stainless steel pressure vessel failure. In this paper, on the basis of Visual Environment 10.0 finite element simulation technology, the residual stress resulting from different welding strength matching coefficients (0.8, 1, 1.2, 1.4) for two S30408 plates welded with three-pass butt welds is calculated according to thermal elastoplastic theory. In addition, the stress field was calculated under a loading as high as 410 MPa and after the load was released. Path 1 was set to analyze stress along the welding line, and path 2 was set to analyze stress normal to the welding line. The welding strength matching coefficient strongly affected both the longitudinal residual stress (center of path 1) and the transverse residual stress (both ends of path 1) after the welding was completed. However, the coefficient had little effect on the longitudinal and transverse residual stress of path 2. Under the loading of 410 MPa, the longitudinal and transverse stress decreased and the stress distribution, with different welding strength matching coefficients, was less diverse. After the load was released, longitudinal and transverse stress distribution for both path 1 and path 2 decreased to a low level. Cold stretching could reduce the effect of residual stress to various degrees. Transverse strain along the stretching direction was also taken into consideration. The experimental results validated the reliability of the partial simulation.

36 MATERIALS SCIENCE↗