Search NASA⌕ Search

SEARCH · Search NASA

Results for “absorbed power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Resolving the Crab Nebula with Direct Hard X-Ray Imaging

We report the first direct hard (25--60 keV) X-ray imaging observation of the Crab Nebula that resolves structure to approximately 0.25 pc. The observation was performed over a 1.4 hour period during a balloon flight from Ft. Sumner, NM, on 2007 May 27. The source was detected in the energy band above the atmospheric cutoff at approx.25 keV and below the mirror graze angle cutoff at approx.60 keV. The image shows elongation about 25 degrees E of N in the direction along the plane of the torus (and perpendicular to the jet axis) with a slight surface-brightness enhancement NE of the pulsar. The spectrum within a 1.7 arcminute radius region centered on the Crab pulsar can be fitted with a Gamma=2 power law absorbed by an atmospheric column consistent with the balloon altitude at the time of observation.

Swartz, Douglas A.↗
NASA NTRS1940

Experimental Determination of Exhaust Gas Thrust, Special Report

This investigation presents the results of tests made on a radial engine to determine the thrust that can be obtained from the exhaust gas when discharged from separate stacks and when discharged from the collector ring with various discharge nozzles. The engine was provided with a propeller to absorb the power and was mounted on a test stand equipped with scales for measuring the thrust and engine torque. The results indicate that at full open throttle at sea level, for the engine tested, a gain in thrust horsepower of 18 percent using separate stacks, and 9.5 percent using a collector ring and discharge nozzle, can be expected at an air speed of 550 miles per hour.

Pinkel, Benjamin↗
NASA NTRS2010

Fabrication of an Absorber-Coupled MKID Detector and Readout for Sub-Millimeter and Far-Infrared Astronomy

We have fabricated absorber-coupled microwave kinetic inductance detector (MKID) arrays for sub-millimeter and far-infrared astronomy. Each detector array is comprised of lambda/2 stepped impedance resonators, a 1.5 micrometer thick silicon membrane, and 380 micrometer thick silicon walls. The resonators consist of parallel plate aluminum transmission lines coupled to low impedance Nb microstrip traces of variable length, which set the resonant frequency of each resonator. This allows for multiplexed microwave readout and, consequently, good spatial discrimination between pixels in the array. The Al transmission lines simultaneously act to absorb optical power and are designed to have a surface impedance and filling fraction so as to match the impedance of free space. Our novel fabrication techniques demonstrate high fabrication yield of MKID arrays on large single crystal membranes and sub-micron front-to-back alignment of the microstrip circuit.

Brown, Ari-David↗
NASA NTRS2012

Discovery of a Pulsar Wind Nebula Candidate in the Cygnus Loop

We report on a discovery of a diffuse nebula containing a point-like source in the southern blowout region of the Cygnus Loop supernova remnant, based on Suzaku and XMM-Newton observations. The X-ray spectra from the nebula and the point-like source are well represented by an absorbed power-law model with photon indices of 2.2+/-0.1 and 1.6+/-0.2, respectively. The photon indices as well as the flux ratio of F(sub nebula)/F(sub point-like) approx. 4 lead us to propose that the system is a pulsar wind nebula, although pulsations have not yet been detected. If we attribute its origin to the Cygnus Loop supernova, then the 0.5-8 keV luminosity of the nebula is computed to be 2.1x10(exp 31)(d/540pc)(exp 2)ergss/2, where d is the distance to the Loop. This implies a spin-down loss-energy E approx. 2.6x10(exp 35)(d/540pc)(exp 2)ergs/s. The location of the neutron star candidate, approx.2deg away from the geometric center of the Loop, implies a high transverse velocity of approx.1850(theta/2deg)(d/540pc)(t/10kyr)/k/s assuming the currently accepted age of the Cygnus Loop.

Katsuda, Satoru↗
NASA NTRS2010

Fabrication of an Absorber-Coupled MKID Detector and Readout for Sub-Millimeter and Far-Infrared Astronomy

We have fabricated absorber-coupled microwave kinetic inductance detector (MKID) arrays for sub-millimeter and farinfrared astronomy. Each detector array is comprised of lambda/2 stepped impedance resonators, a 1.5μm thick silicon membrane, and 380μm thick silicon walls. The resonators consist of parallel plate aluminum transmission lines coupled to low impedance Nb microstrip traces of variable length, which set the resonant frequency of each resonator. This allows for multiplexed microwave readout and, consequently, good spatial discrimination between pixels in the array. The Al transmission lines simultaneously act to absorb optical power and are designed to have a surface impedance and filling fraction so as to match the impedance of free space. Our novel fabrication techniques demonstrate high fabrication yield of MKID arrays on large single crystal membranes and sub-micron front-to-back alignment of the microstrip circuit.

far-infrared↗
NASA NTRS2013

Nustar and Chandra Insight into the Nature of the 3-40 Kev Nuclear Emission in Ngc 253

We present results from three nearly simultaneous Nuclear Spectroscopic Telescope Array (NuSTAR) and Chandra monitoring observations between 2012 September 2 and 2012 November 16 of the local star-forming galaxy NGC 253. The 3-40 kiloelectron volt intensity of the inner approximately 20 arcsec (approximately 400 parsec) nuclear region, as measured by NuSTAR, varied by a factor of approximately 2 across the three monitoring observations. The Chandra data reveal that the nuclear region contains three bright X-ray sources, including a luminous (L (sub 2-10 kiloelectron volt) approximately few × 10 (exp 39) erg per s) point source located approximately 1 arcsec from the dynamical center of the galaxy (within the sigma 3 positional uncertainty of the dynamical center); this source drives the overall variability of the nuclear region at energies greater than or approximately equal to 3 kiloelectron volts. We make use of the variability to measure the spectra of this single hard X-ray source when it was in bright states. The spectra are well described by an absorbed (power-law model spectral fit value, N(sub H), approximately equal to 1.6 x 10 (exp 23) per square centimeter) broken power-law model with spectral slopes and break energies that are typical of ultraluminous X-ray sources (ULXs), but not active galactic nuclei (AGNs). A previous Chandra observation in 2003 showed a hard X-ray point source of similar luminosity to the 2012 source that was also near the dynamical center (Phi is approximately equal to 0.4 arcsec); however, this source was offset from the 2012 source position by approximately 1 arcsec. We show that the probability of the 2003 and 2012 hard X-ray sources being unrelated is much greater than 99.99% based on the Chandra spatial localizations. Interestingly, the Chandra spectrum of the 2003 source (3-8 kiloelectron volts) is shallower in slope than that of the 2012 hard X-ray source. Its proximity to the dynamical center and harder Chandra spectrum indicate that the 2003 source is a better AGN candidate than any of the sources detected in our 2012 campaign; however, we were unable to rule out a ULX nature for this source. Future NuSTAR and Chandra monitoring would be well equipped to break the degeneracy between the AGN and ULX nature of the 2003 source, if again caught in a high state.

Chandra↗
NASA NTRS2016

Hard X-Ray Emission from SH 2-104: A NuSTAR Search for Gamma-Ray Counterparts

We present NuSTAR hard X-ray observations of Sh 2-104, a compact H II region containing several young massive stellar clusters (YMSCs). We have detected distinct hard X-ray sources coincident with localized VERITAS TeV emission recently resolved from the giant gamma-ray complex MGRO J2019+37 in the Cygnus region. Fainter, diffuse X-rays coincident with the eastern YMSC in Sh2-104 likely result from the colliding winds of a component star. Just outside the radio shell of Sh 2-104 lies 3XMM J201744.7+365045 and a nearby nebula, NuSTAR J201744.3+364812, whose properties are most consistent with extragalactic objects. The combined XMM-Newton and NuSTAR spectrum of 3XMM J201744.7+365045 is well-fit to an absorbed power-law model with N(sub H) = (3.1 +/- 1.0) x 10(exp 22) cm(exp -2) and a photon index gamma = 2.1 +/- 0.1. Based on possible long-term flux variation and the lack of detected pulsations (less than or equal to 43% modulation), this object is likely a background active galactic nucleus rather than a Galactic pulsar. The spectrum of the NuSTAR nebula shows evidence of an emission line at E = 5.6 keV, suggesting an optically obscured galaxy cluster at z = 0.19 +/- 0.02 (d = 800 Mpc) and L(sub X) = 1.2 x 10(exp 44) erg s(exp -1). Follow-up Chandra observations of Sh 2-104 will help identify the nature of the X-ray sources and their relation to MGRO J2019+37. We also show that the putative VERITAS excess south of Sh 2-104, is most likely associated with the newly discovered Fermi pulsar PSR J2017+3625 and not the H II region.

SM: individual objects↗
NASA NTRS2020

NuSTAR Observation of GROJ1744−28 at Low Mass Accretion Rate

Context.Neutron stars in low-mass X-ray binaries (LMXBs) are important systems to study the physics of accretion onto compact ob-jects. The system GRO J1744−28 is particularly interesting, as it usually shows clear pulsations as well as X-ray bursts. Additionally,there are claims for a magnetic field of 5×1011G through the detection of a Cyclotron Resonant Scattering Feature (CRSF).Aims.We present the spectral analysis of GRO J1744−28 using∼29 ks of NuSTAR data taken in 2017 February at a low luminosityof 3.2×1036erg s−1(3–50 keV). Our goal is to study the variability of the source spectrum with pulse phase and to search for the claimed CRSF. Methods.The continuum spectrum is modeled with an absorbed power-law with exponential cut-off, and an additional iron line component. We find no obvious indications for a CRSF and therefore perform a detailed cyclotron line search using statistical methods.We perform this search on pulse phase-averaged as well as phase-resolved spectra. Results.GRO J1744−28 was observed at one of the lowest luminosities studied so far. The previously detected Type II X-ray bursts re absent. Clear pulsations at a period of 2.141124(9) Hz are detected. The pulse profile shows an indication of a secondary peak,which was not seen at higher flux. The 4σupper limit for the strength of a CRSF in the 3–20 keV band is 0.07 keV, lower than the strength of the line found at higher luminosity. Conclusions.The detection of pulsations shows that the source did not enter the “propeller” regime, even though the source flux of4.15×10−10erg cm−2s−1was almost one order of magnitude below the threshold for the propeller regime claimed in previous studies on this source. The transition into the propeller regime in GRO J1744−28 must therefore be below a luminosity of 3.2×1036erg s−1(3–50 keV), which implies a surface magnetic field.2.9×1011G and mass accretion rate.1.7×1016g s−1. A change of the CRSF depth as function of luminosity is not unexpected and has been observed in other sources. This result possibly implies a change in emission geometry as function of mass accretion rate to reduce the depth of the line below our detection limit.

Ole König↗
NASA NTRS2022

X-Ray Imaging Observations of the High-Mass γ-Ray Binary HESS J0632+057

The Chandra X-ray Observatory (CXO)imaged the high-massγ-ray binary (HMGB) HESS8J0632+057 with the Advanced CCD Imaging Spectrometer (ACIS). We analyzed the CXO data to-9gether with 967 ks of archival imaging Swift-XRT observations. On arcsecond scales we find a hint10of asymmetric extended emission. On arcminute scales, there is a region of extended emission (“the11blob”) which is located≈5.5′east of the binary. The blob is seen in both the CXO-ACIS and the12Swift-XRT images but it does not have a counterpart in the radio, NIR, IR, or optical images. The13ACIS spectrum of the blob fits either an absorbed power-law model with Γ'2.6, or a thermal plasma14model withkT'3 keV. Since the blob’s NH is significantly larger than that of the binary we conclude15that the blob and binary are not directly related. The somewhat larger very deep XRT image suggests16that the binary may be located within a shell (or cavity). The four ACIS spectra taken within the∼2017day interval near the light curve minimum suggests that the NH is varying on timescales of days, pos-18sibly due to the inhomogenous circumbinary environment. The XRT spectra extracted from the wider19orbital phase intervals support significant changes in NH near the light curve maximum/minimum,20which may be responsible for the substantial systematic residuals seen near 1 keV, and provide tenta-21tive evidence for a Fe line at 6.4 keV. We find no significant periodic signal in the ACIS data up to 0.156 Hz.

O Kargaltsev↗
NASA NTRS2022

Cryogenic Thermal Coatings Final Report

The goals of this project were to produce yttrium oxide- (Y2O3) based tiles and a spray-on coating with minimal solar absorption, to perform exposure testing on these coatings (both rigid and sprayon), and to work towards a manufacturing process whereby these coatings could be made available to the space community. The Key Performance Parameters (threshold values) were to achieve 1% solar absorption for the tiles as measured in a deep space simulator, and 6% solar absorption for the spray-on coating as measured using a reflectance spectrometer. The values achieved were 1.2% (GRC Deep space simulator) and 4% (KSC spectrometer using Spectralon as a reference) for the tiles and spray-on coating, respectively. Exposure testing consisted of measuring tile and spray-on coating degradation due to atomic oxygen, ultraviolet radiation, and electrostatic fields. Atomic oxygen caused some degradation, while ultraviolet exposure caused a significant increase in absorption. However, in-space samples exposed to solar ultraviolet did not show this significant increase. This discrepancy is addressed in this report. As a result of this work, Y2O3 tiles have been manufactured in the Kennedy Space Center (KSC) Applied Chemistry Laboratory (ACL), and the process has been transferred to the Thermal Protection System Facility (TPSF) at KSC. The TPSF manufactures coatings for the space community and is an ideal route by which future users could access Y2O3-based coatings. The spray-on coating has been developed such that it can be applied to a wide range of substrates, substantially lowering absorbed solar power as compared to currently available coatings.

Thermal Control Coatings↗
DOE OSTI2024

3D Printing of Inconel 718 with Enhanced Boron Composition as a Novel Solar Absorber Tube Material in the Concentrated Solar Power (CSP) System

The growing demands for elevated efficiency in the solar energy industry led researchers to focus on the development of functional solar absorber tube material in concentrated solar power (CSP) systems, when molten salts are adopted as the heat transfer fluid. In this study, the typical solar absorber tube material, Inconel 718, was enhanced with boron to achieve a higher solar absorptivity in the visible light spectrum. Combined with an additive manufacturing (AM) method, the boron composition exceeded the traditional manufacturing limit of 60 ppm without microstructural defects. The boron-enhanced Inconel 718 exhibited a high solar absorptivity of nearly 90 % while maintaining a high thermal cycle fatigue resistance after thermal cycling treatment between 550°C and 720°C. The boron composition was increased to the manufacturing failure point, and the effects of different boron compositions on mechanical properties, microstructure, and optical properties were studied. The provided microstructure-property map in this study delivers high potentials of functional AM-printed alloy material in CSP applications.

13 HYDRO ENERGY↗
NASA NTRS2019

An Evolving Broad Iron Line from the First Galactic Ultraluminous X-Ray Pulsar Swift J0243.6+6124

We present a spectral study of the ultraluminous Be/X-ray transient pulsar Swift J0243.6+6124 using Neutron Star Interior Composition Explorer (NICER) observations during the system's 2017–2018 giant outburst. The 1.2–10 keV energy spectrum of the source can be approximated with an absorbed cutoff power-law model. We detect strong, luminosity-dependent emission lines in the 6–7 keV energy range. A narrow 6.42 keV line, observed in the sub-Eddington regime, is seen to evolve into a broad Fe-line profile in the super-Eddington regime. Other features are found at 6.67 and 6.97 keV in the Fe-line complex. An asymmetric broad-line profile, peaking at 6.67 keV, is possibly due to Doppler effects and gravitational redshift. The 1.2–79 keV broadband spectrum from Nuclear Spectroscopic Telescope Array (NuSTAR) and NICER observations at the outburst peak is well described by an absorbed cutoff power law plus multiple Gaussian lines and a blackbody component. Physical reflection models are also tested to probe the broad iron-line feature. Depending on the mass accretion rate, we found emission sites that are evolving from ~5000 km to a range closer to the surface of the neutron star. Our findings are discussed in the framework of the accretion disk and its implication on the magnetic field, the presence of optically thick accretion curtain in the magnetosphere, jet emission, and the massive, ultrafast outflow expected at super-Eddington accretion rates. We do not detect any signatures of a cyclotron absorption line in the NICER or NuSTAR data.

Gaurava K. Jaisawal↗
DOE OSTI2022

Midfidelity model verification for a point-absorbing wave energy converter with linear power take-off

In the preliminary design stage of a wave energy converter (WEC), researchers need fast and reliable simulation tools. High-fidelity numerical models are usually employed to study the wave-structure interaction, but the computational cost is demanding. As an alternative, midfidelity models can provide simulations in the order of real time. In this study, we operate Uppsala University’s WEC in a relatively mild sea state and model it using WEC-Sim. The model is verified based on OpenFOAM simulations. To analyze the ability of the midfidelity model to capture WEC dynamics, we investigate the system separately with 1, 2, and 3 degrees of freedom. We examine the contribution of viscous phenomena, and study both linear and weakly nonlinear solutions provided by WEC-Sim. Our results indicate that the viscous effects can be neglected in heave and surge motion, but not for pitch. We also find that the weakly nonlinear WEC-Sim solution successfully agrees with the computational fluid dynamics, whereas the linear solution could suggest misleading results.

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Midfidelity Model Verification for a Point-Absorbing Wave Energy Converter with Linear Power Takeoff: Preprint

In the preliminary design stage of a wave energy converter (WEC), fast and reliable simulation tools are required. High-fidelity numerical models are usually employed to study the wave-structure interaction, yet the computational cost is demanding. Instead, mid-fidelity models provide simulations in the order of real time. In this study, Uppsala University WEC operates in a relatively mild sea state and is modeled using WEC-Sim. The model is verified based on OpenFOAM simulations. To analyze the ability of mid-fidelity model to capture the WEC dynamics, the system is investigated separately in 1, 2 and 3 DoF. The contribution of viscous phenomena is examined. Moreover, linear and weakly non-linear solutions provided by WEC-Sim are studied. The results obtained indicate that the viscous effects in heave and surge motion can be neglected but not for the pitch. The weakly non-linear WEC-Sim solution successfully agrees with the CFD, whereas the linear solution could drive to misleading results.

CFD↗
DOE OSTI2021

Midfidelity Model Verification for a Point-Absorbing Wave Energy Converter with Linear Power Take-Off

In the preliminary design stage of a wave energy converter (WEC), fast and reliable simulation tools are required. High-fidelity numerical models are usually employed to study the wave-structure interaction, yet the computational cost is demanding. Instead, mid-fidelity models provide simulations in the order of real time. In this study, Uppsala University WEC operates in a relatively mild sea state and is modeled using WEC-Sim. The model is verified based on OpenFOAM simulations. To analyze the ability of mid-fidelity model to capture the WEC dynamics, the system is investigated separately in 1, 2 and 3 DoF. The contribution of viscous phenomena is examined. Moreover, linear and weakly non-linear solutions provided by WEC-Sim are studied. The results obtained indicate that the viscous effects in heave and surge motion can be neglected but not for the pitch. The weakly non-linear WEC-Sim solution successfully agrees with the CFD, whereas the linear solution could drive to misleading results.

CFD↗
NASA NTRS1989

Lunar drill footplate and casing

To prevent hole collapse during lunar drilling operations, a casing has been devised of a graphite reinforced polyimide composite which will be able to withstand the lunar environment. Additionally, this casing will be inserted into the ground in segments two meters long which will penetrate the regolith simultaneously with the auger. The vertical action of the mobile platform will provide a downward force to the casing string through a special adaptor, giving the casing the needed impetus to sink the anticipated depth of ten meters. Casing segments will be connected with a simple snap arrangement. Excess casing will be cut off by a cylindrical cutting tool which will also transport the excess casing away from the hole. A footplate will be incorporated to grasp the auger rod string during rod segment additions or removals. The footplate grasping mechanism will consist of a set of vice-like arms, one end of each bearing threaded to a common power screw. The power screw will be threaded such that one end's thread pitch opposes that of the other end. The weight of the auger and rod string will be transmitted through the arms to the power screw and absorbed by a set of three ball bearing assemblies. The power screw will be driven by a one-half horsepower brushless motor actuated by radio control. The footplate will rest on four short legs and be anchored with pins that are an integral part of each leg.

Maassen, Erik C.↗
NASA NTRS2004

Multi-Epoch XMM Observations of NGC4258

The goal of this project was detection of variability in the X-ray absorption column of the AGN in NGC4258 through monitoring with the XMM satellite. We have accomplished this goal and submitted the results to ApJ for publication in a paper entitled, "X-ray Luminosity and Absorption Column Fluctuations in the H2O Maser Galaxy NGC4258 from Weeks to Years," by Fruscione, A., Greenhill, L.J., Filippedco, A.V., Moran, J.M., Hermstein, J.R., and Galle, E. We have received a favorable referee report and expect the article will appear in 2005. To complete the project, we reduced our four epochs of XMM data for NGC4258, one archival XMM observation, and all existing Chandra datasets for NGC4258 (with the latest calibration tables and a grid of corrections for pileup). Self-consistent reduction of all these data permitted detailed comparison that could not have been accomplished simply by taking published model fits that appear in the literature. To accumulate a broader monitoring record, we combined the Chandra and XMM results with those published for SAX and ASCA. We modeled the Chandra and XMM data self-consistently with partially absorbed, hard power-law, soft thermal plasmas, and soft power-law components. Over nine years, the photo-electric absorbing column exhibited a 40% drop between two ASCA epochs separated by 3 years and a 60% rise between two XMM epochs separated by just 5 months. In contract, uncorrelated factor of of 2-3 changes were seen in absorbed flux on te timescale of years, which suggests intrinsic variability of the central engine. The warped disk that is a known source of H2O maser emission in 4258 is believed to cross the line of sight to the central engine. We have proposed that the variations in absorbing column arise from inhomogeneities in the rotating disk, as they sweep across the line of sight. We estimate from the XMM data that the inhomogeneities are about 1E+15 cm in size at radii greater than 0.27 pc. This is consistent with the estimated radius of the disk crossing estimated entirely independently, and it solidifies evidence that the warped accretion disk is the absorber in this (and possible other) AGN.

Greenhill, Lincoln J.↗
NASA NTRS2005

Hydrogen-Oxygen PEM Regenerative Fuel Cell Development at the NASA Glenn Research Center

The closed-cycle hydrogen-oxygen PEM regenerative fuel cell (RFC) at the NASA Glenn Research Center has successfully demonstrated closed cycle operation at rated power for multiple charge-discharge cycles. During charge cycle the RFC has absorbed input electrical power simulating a solar day cycle ranging from zero to 15 kWe peak, and delivered steady 5 kWe output power for periods exceeding 8 hr. Orderly transitions from charge to discharge mode, and return to charging after full discharge, have been accomplished without incident. Continuing test operations focus on: (1) Increasing the number of contiguous uninterrupted charge discharge cycles; (2) Increasing the performance envelope boundaries; (3) Operating the RFC as an energy storage device on a regular basis; (4) Gaining operational experience leading to development of fully automated operation; and (5) Developing instrumentation and in situ fluid sampling strategies to monitor health and anticipate breakdowns.

Bents, David J.↗