Search NASA⌕ Search

SEARCH · Search NASA

Results for “active acoustic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Active Control of Fan Noise: Feasibility Study: Active Fan Noise Cancellation in the NASA Lewis Active Noise Control Fan Facility - Volume 3

This report describes the Active Noise Cancellation (ANC) System designed by General Electric and tested in the NASA Lewis Research Center's (LERC) 48 inch Active Noise Control Fan (ANCF). The goal of this study is to assess the feasibility of using wall mounted secondary acoustic sources and sensors within the duct of a high bypass turbofan aircraft engine for global active noise cancellation of fan tones. The GE ANC system is based on a modal control approach. A known acoustic mode propagating in the fan duct is canceled using an array of flush-mounted compact sound sources. The canceling modal signal is generated by a modal controller. Inputs to the controller are signals from a shaft encoder and from a microphone array which senses the residual acoustic mode in the duct. The key results are that the (6,0) was completely eliminated at the 920 Hz design frequency and substantially reduced elsewhere. The total tone power was reduced 6.8 dB (out of a possible 9.8 dB). Farfield reductions of 15 dB (SPL) were obtained. The (4,0) and (4,1) modes were reduced simultaneously yielding a 15 dB PWL decrease. The results indicate that global attenuation of PWL at the target frequency was obtained in the aft quadrant using an ANC actuator and sensor system totally contained within the duct. The quality of the results depended on precise mode generation. High spillover into spurious modes generated by the ANC actuator array caused less than optimum levels of PWL reduction. The variation in spillover is believed to be due to calibration procedure, but must be confirmed in subsequent tests.

Pla, Frederic G.↗
NASA NTRS1996

Modeling of Sound Transmission through Shell Structures with Turbulent Boundary Layer Excitation

The turbulent boundary layer (TBL) pressure field is an important source of cabin noise during cruise of high subsonic and supersonic commercial aircraft. The broadband character of this excitation field results in an interior noise spectrum that dominates the overall sound pressure level (SPL) and speech interference metrics in the forward and midcabins of many aircraft. In the authors' previous study, sound transmission through an aircraft fuselage, modeled by two concentric cylindrical sandwich shells and excited by a TBL statistical model was investigated analytically. An assessment of point and global structural vibration levels and resulting interior noise levels was obtained for different TBL models, flight conditions and fuselage structural designs. However, due to the complication of the shell structure, the important noise transmission mechanisms were difficult to discern. Previous experience has demonstrated that a fundamental understanding of the range of modes (or wavenumbers) generated by the TBL source both in the structure and the acoustic cavity is key to the development of both active and passive control technologies. In an initial effort to provide this insight, the objective of this paper is to develop an analytical model of sound transmission through a simple unstiffened cylindrical aluminum shell excited by a TBL pressure field. The description of the turbulent pressure field is based on the Corcos formulation for the cross-spectral density (CSD) of the pressure fluctuations. The coupled shell and interior and exterior acoustic equations are solved for the structural displacement and the interior acoustic response using a Galerkin approach to obtain analytical solutions. Specifically, this study compares the real part of the normalized CSD of the TBL excitation field, the structural displacement and the interior acoustic field. Further the modal compositions of the structural and cavity response are examined and some inference of the dominant mechanism of noise transmission is made.

Tang, Yvette Y.↗
NASA NTRS1977

Investigation of a stall deterrent system utilizing an acoustic stall sensor

A simple rugged acoustic stall sensor which has an output proportional to angle of attack near wing stall has been evaluated on a Cessna 319 aircraft. A sensor position has been found on the wing where the sensor output is only slightly affected by engine power level, yaw angle, flap position and wing roughness. The NASA LRC General Aviation Simulator has been used to evaluate the acoustic sensor output as a control signal for active stall deterrent systems. It has been found that a simple control algorithm is sufficient for stall deterrence.

Bennett, A. G.↗
NASA NTRS1988

Prediction of stresses in aircraft panels subjected to acoustic forces

Summarized are the progress and accomplishments performed under NASA/Langley Research Center Master Agreement NAS1-17993, Task Assignment No. 22, entitled Prediction of Stresses in Aircraft Panels Subjected to Acoustic Forces, for the period October 1, 1985 to December 15, 1987. The primary effort of this task is the development of analytical methods for prediction of stresses in aircraft panels subjected to acoustic forces. The progress and accomplishments of various activities are discussed first. Then, publications, presentations and thesis are presented.

Mei, Chuh↗
NASA NTRS1994

Stiffening of the ACES deployable space boom

The purpose of this design project was to design an active planar stiffening device for the existing ACES (Acoustic Containerless Experiment System) structure. the ACES structure was modeled using simple beam theory. Various concepts were generated about how the stiffening device should be configured in order to perform at an optimum level. The optimum configuration was selected to be a single set of spreaders located approximately 63% of the distance down the beam. Actuation was to be provided by a DC electric motor. From the test results, the design group was able to draw conclusions and make recommendations about the utility of further research into this area.

Sidwell, Vince↗
NASA NTRS2001

Active Shielding and Control of Environmental Noise

In the framework of the research project supported by NASA under grant # NAG-1-01064, we have studied the mathematical aspects of the problem of active control of sound, i.e., time-harmonic acoustic disturbances. The foundations of the methodology are described in our paper [1]. Unlike. many other existing techniques, the approach of [1] provides for the exact volumetric cancellation of the unwanted noise on a given predetermined region airspace, while leaving unaltered those components of the total acoustic field that are deemed as friendly. The key finding of the work is that for eliminating the unwanted component of the acoustic field in a given area, one needs to know relatively little; in particular, neither the locations nor structure nor strength of the exterior noise sources need to be known. Likewise, there is no need to know the volumetric properties of the supporting medium across which the acoustic signals propagate, except, maybe, in a narrow area of space near the perimeter of the protected region. The controls are built based solely on the measurements performed on the perimeter of the domain to be shielded; moreover, the controls themselves (i.e., additional sources) are concentrated also only on or near this perimeter. Perhaps as important, the measured quantities can refer to the total acoustic field rather than to its unwanted component only, and the methodology can automatically distinguish between the two. In [1], we have constructed the general solution for controls. The apparatus used for deriving this general solution is closely connected to the concepts of generalized potentials and boundary projections of Calderon's type. For a given total wave field, the application of a Calderon's projection allows one to definitively tell between its incoming and outgoing components with respect to a particular domain of interest, which may have arbitrary shape. Then, the controls are designed so that they suppress the incoming component for the domain to be shielded or alternatively, the outgoing component for the domain, which is complementary to the one to be shielded.

Tsynkov, S. V.↗
NASA NTRS2002

Active Control of Combustor Instability Shown to Help Lower Emissions

In a quest to reduce the environmental impact of aerospace propulsion systems, extensive research is being done in the development of lean-burning (low fuel-to-air ratio) combustors that can reduce emissions throughout the mission cycle. However, these lean-burning combustors have an increased susceptibility to thermoacoustic instabilities, or high-pressure oscillations much like sound waves, that can cause severe high-frequency vibrations in the combustor. These pressure waves can fatigue the combustor components and even the downstream turbine blades. This can significantly decrease the safe operating life of the combustor and turbine. Thus, suppression of the thermoacoustic combustor instabilities is an enabling technology for lean, low-emissions combustors. Under the Aerospace Propulsion and Power Base Research and Technology Program, the NASA Glenn Research Center, in partnership with Pratt & Whitney and United Technologies Research Center, is developing technologies for the active control of combustion instabilities. With active combustion control, the fuel is pulsed to put pressure oscillations into the system. This cancels out the pressure oscillations being produced by the instabilities. Thus, the engine can have lower pollutant emissions and long life.The use of active combustion instability control to reduce thermo-acoustic-driven combustor pressure oscillations was demonstrated on a single-nozzle combustor rig at United Technologies. This rig has many of the complexities of a real engine combustor (i.e., an actual fuel nozzle and swirler, dilution cooling, etc.). Control was demonstrated through modeling, developing, and testing a fuel-delivery system able to the 280-Hz instability frequency. The preceding figure shows the capability of this system to provide high-frequency fuel modulations. Because of the high-shear contrarotating airflow in the fuel injector, there was some concern that the fuel pulses would be attenuated to the point where they would not be effective for control. Testing in the combustor rig showed that open-loop pulsing of the fuel was, in fact, able to effectively modulate the combustor pressure. To suppress the combustor pressure oscillations due to thermoacoustic instabilities, it is desirable to time the injection of the fuel so that it interferes with the instability. A closed-loop control scheme was developed that uses combustion pressure feedback and a phase-shifting controller to time the fuel-injection pulses. Some suppression of the pressure oscillations at the 280-Hz instability frequency was demonstrated (see the next figure). However, the overall peak-to- peak pressure oscillations in the combustor were only mildly reduced. Improvements to control hardware and control methods are being continued to gain improved closed-loop reduction of the pressure oscillations.pulse the fuel at

DeLaat, John C.↗
NASA NTRS2015

Flexible Micropost Arrays for Shear Stress Measurement

Increased fuel costs, heightened environmental protection requirements, and noise abatement continue to place drag reduction at the forefront of aerospace research priorities. Unfortunately, shortfalls still exist in the fundamental understanding of boundary-layer airflow over aerodynamic surfaces, especially regarding drag arising from skin friction. For example, there is insufficient availability of instrumentation to adequately characterize complex flows with strong pressure gradients, heat transfer, wall mass flux, three-dimensionality, separation, shock waves, and transient phenomena. One example is the acoustic liner efficacy on aircraft engine nacelle walls. Active measurement of shear stress in boundary layer airflow would enable a better understanding of how aircraft structure and flight dynamics affect skin friction. Current shear stress measurement techniques suffer from reliability, complexity, and airflow disruption, thereby compromising resultant shear stress data. The state-of-the-art for shear stress sensing uses indirect or direct measurement techniques. Indirect measurements (e.g., hot-wire, heat flux gages, oil interferometry, laser Doppler anemometry, small scale pressure drag surfaces, i.e., fences) require intricate knowledge of the studied flow, restrictive instrument arrangements, large surface areas, flow disruption, or seeding material; with smaller, higher bandwidth probes under development. Direct measurements involve strain displacement of a sensor element and require no prior knowledge of the flow. Unfortunately, conventional "floating" recessed components for direct measurements are mm to cm in size. Whispering gallery mode devices and Fiber Bragg Gratings are examples of recent additions to this type of sensor with much smaller (m) sensor components. Direct detection techniques are often single point measurements and difficult to calibrate and implement in wind tunnel experiments. In addition, the wiring, packaging, and installation of delicate micro-electromechanical devices impede the use of most direct shear sensors. Similarly, the cavity required for sensing element displacement is sensitive to particulate obstruction. This work was focused on developing a shear stress sensor for use in subsonic wind tunnel test facilities applicable to an array of test configurations. The non-displacement shear sensors described here have minimal packaging requirements resulting in minimal or no disturbance of boundary layer flow. Compared to previous concepts, device installation could be simple with reduced cost and down-time. The novelty lies in the creation of low profile (nanoscale to 100 μm) micropost arrays that stay within the viscous sub-layer of the airflow. Aerodynamic forces, which are related to the surface shear stress, cause post deflection and optical property changes. Ultimately, a reliable, accurate shear stress sensor that does not disrupt the airflow has the potential to provide high value data for flow physics researchers, aerodynamicists, and aircraft manufacturers leading to greater flight efficiency arising from more in-depth knowledge on how aircraft design impacts near surface properties.

Wohl, Christopher J.↗
NASA NTRS1993

Mg II and Ly-alpha fluxes in M dwarfs - Evaluation of an acoustic model

Surface fluxes of Mg II and Ly-alpha from a sample of M dwarfs have been reported by Panagi and Mathioudakis (PM, 1992). In order to determine if acoustic effects can reproduce the fluxes in the least active ('basal') stars in the PM sample, we have constructed steady state models of plane-parallel atmospheres with T(eff) = 3000 and 4000 K including heating by shock dissipation. The models incorporate radiative losses in the chromosphere by solving the transfer equation for two strong lines (Mg II k and Ly-alpha). Predictions of standard weak shock theory are expected to overestimate the rate of energy deposition in the chromospheres of M dwarfs compared to the rate of deposition in F, G, or K dwarfs. In order to incorporate this effect in M dwarfs, we compute a series of atmospheric models in which, for a given T(eff), the standard weak shock dissipation rate is reduced by a series of factors F(r). Although the input acoustic flux F(mech) may in principle be determined uniquely by T(eff) and log g, the correct value to use in any particular case is not well known. We therefore use F(mech) and F(r) as parameters to construct a family of M dwarf models at various T(eff) and g. Comparing with the observed fluxes in the least active M dwarfs of the PM sample, we find that our models reproduce the observed fluxes of both Mg II and Ly-alpha best if F(mech) is close to the value predicted by Bohn (1984) and if F(r) is approximately equal to 10-20.

Mullan, D. J.↗
NASA NTRS1999

STS-96 FD Highlights and Crew Activities Report: Flight Day 05

On this fifth day of the STS-96 Discovery mission, the flight crew, Commander Kent V. Rominger, Pilot Rick D. Husband, and Mission Specialists Ellen Ochoa, Tamara E. Jernigan, Daniel T. Barry, Julie Payette, and Valery Ivanovich Tokarev are seen performing logistics transfer activities within the Discovery/International Space Station orbiting complex. The crew transfers supplies, equipment, and water. Payette and Tokarev perform maintenance activities on the storage batteries in the Zarya module. Barry and Tokarev install acoustic insulation around some of the fans inside Zarya. Jernigan and Husband install shelving in 2 soft stowage racks. Husband and Barry troubleshoot and perform maintenance activities on the Early Communications System. At the end of the workday, Rominger, Jernigan, and Barry discussed the progress of the mission with NBC's "Today," CBS "This Morning," and CNN.

Source record↗
NASA NTRS1993

Preliminary analysis of the JAPE ground vehicle test data with an artificial neural network classifier

Remotely sensing and classifying military vehicles in a battlefield environment have been the source of much research over the past 20 years. The ability to know where threat vehicles are located is an obvious advantage to military personnel. In the past active methods of ground vehicle detection such as radar have been used, but with the advancement of technology to locate these active sensors, passive sensors are preferred. Passive sensors detect acoustic emissions, seismic movement, electromagnetic radiation, etc., produced by the target and use this information to describe it. Deriving the mathematical models to classify vehicles in this manner has been, and is, quite complex and not always reliable. However, with the resurgence of artificial neural network (ANN) research in the past few years, developing models for this work may be a thing of the past. Preliminary results from an ANN analysis to the tank signatures recorded at the Joint Acoustic Propagation Experiment (JAPE) at the US Army White Sands Missile Range, NM, in July 1991, are presented.

Larsen, Nathan F.↗
NASA NTRS1994

Active minimization of energy density in three-dimensional enclosures

The objective of this research project is to further investigate and develop a novel approach for actively controlling the sound field in enclosures. Typically the acoustic field in an enclosure has been controlled by minimizing the sum of the squared pressures from several microphones distributed throughout the enclosure. The approach being investigated in this project involves minimizing the acoustic energy density at the sensor locations, rather than the squared pressure. Previous research in a simple one-dimensional enclosure showed that improved global attenuation of the acoustic field is often obtained by minimizing the energy density, rather than the pressure. The current project builds on the previous research by extending the method of controlling the acoustic energy density to three-dimensional enclosures. The results will establish if improved control can still be expected in a more general enclosure. Pending successful results, the method could be applied to control problems such as attenuating the acoustic noise in an aircraft fuselage, an automobile cabin, or other general enclosures. The research project was set up as a two-year project designed to achieve both numerical and experimental results. The primary focus of the first year of research (now being completed) was on the analytical/numerical modeling of the method of controlling the acoustic energy density. During the second year, the research focuses on experimental verification of the approach and extending our understanding of the method.

Sommerfeldt, Scott D.↗
NASA NTRS1997

Large Scale Turbulent Structures in Supersonic Jets

Jet noise is a major concern in the design of commercial aircraft. Studies by various researchers suggest that aerodynamic noise is a major contributor to jet noise. Some of these studies indicate that most of the aerodynamic jet noise due to turbulent mixing occurs when there is a rapid variation in turbulent structure, i.e. rapidly growing or decaying vortices. The objective of this research was to simulate a compressible round jet to study the non-linear evolution of vortices and the resulting acoustic radiations. In particular, to understand the effect of turbulence structure on the noise. An ideal technique to study this problem is Direct Numerical Simulations(DNS), because it provides precise control on the initial and boundary conditions that lead to the turbulent structures studied. It also provides complete 3-dimensional time dependent data. Since the dynamics of a temporally evolving jet are not greatly different from those, of a spatially evolving jet, a temporal jet problem was solved, using periodicity ill the direction of the jet axis. This enables the application of Fourier spectral methods in the streamwise direction. Physically this means that turbulent structures in the jet are repeated in successive downstream cells instead of being gradually modified downstream into a jet plume. The DNS jet simulation helps us understand the various turbulent scales and mechanisms of turbulence generation in the evolution of a compressible round jet. These accurate flow solutions will be used in future research to estimate near-field acoustic radiation by computing the total outward flux across a surface and determine how it is related to the evolution of the turbulent solutions. Furthermore, these simulations allow us to investigate the sensitivity of acoustic radiations to inlet/boundary conditions, with possible application to active noise suppression. In addition, the data generated can be used to compute various turbulence quantities such as mean velocities, turbulent stresses, etc. which will aid in turbulence modeling. This report will be presented in two chapters. The first chapter describes some work on the linear stability of a supersonic round jet and the implications of this for the jet noise problem. The second chapter is an extensive discussion of numerical work using the spectral method which we use to solve the compressible Navier-Stokes equations to study turbulent jet flows. The method uses Fourier expansions in the azimuthal and streamwise direction and a 1-D B-spline basis representation in the radial direction. The B-spline basis is locally supported and this ensures block diagonal matrix equations which can be solved in O(N) steps. This is a modification of a boundary layer code developed by Robert Moser. A very accurate highly resolved Direct Numerical Simulation (DNS) of a turbulent jet flow is produced.

Rao, Ram Mohan↗
NASA NTRS2001

Operational Performance of Sensor Systems Used to Determine Atmospheric Boundary Layer Properties as Part of the NASA Aircraft Vortex Spacing System Project

There has been a renewed interest in the application of remote sensor technology to operational aviation and airport-related activities such as Aircraft Vortex Spacing System (AVOSS). Radio Acoustic Sounding Systems (RASS), Doppler-acoustic sodars, Ultrahigh Frequencies (UHF) profilers and lidars have many advantages in measuring wind and temperature profiles in the lower atmospheric boundary layer since they can operate more or less continuously and unattended; however, there are limitations in their operational use at airports. For example, profilers deteriorate (limited altitude coverage or missing) in moderate or greater rain and can be affected by airplane targets in their field of view. Sodars can handle precipitation better but are affected by the high noise environments of airports and strong winds. Morning temperature inversions typically limit performance of RASS, sodars and profilers. Fog affects sonic anemometers. Lidars can have difficulties in clouds, fog or heavy precipitation. Despite their limitations these sensors have proven useful to provide wind and temperature profiles for AVOSS. Capabilities and limitations of these and other sensors used in the AVOSS program are discussed, parameter settings for the sensor systems are documented, and recommendations are made for the most cost-effective group of sensors for the future. The potential use of specially tuned dynamic forecast models and measurements from landing and departing aircraft are addressed.

Zak, J. Allen↗
NASA NTRSDate not supplied

Development of the 10% NASA CRM High-Lift Common Research Model (CRM-HL)

A 10%-scale Common Research Model-high lift version (CRM-HL) was developed to support extensive experimental investigations in the areas of active flow control, control surface optimization for landing and take-off, acoustic technology development, and computational fluid dynamics code validation to name a few. The CRM-HL was designed to have modular components that will enable the model to be tested in the following three forms: (1) conventional high-lift (CHL) configuration, (2) Active Flow Control (AFC) enabled simple hinged flap high-lift (SHL) configuration, and (3) CHL configuration with noise reduction treatments for the slats and/or the flaps. This paper describes the design, analysis, and fabrication of the CRM-HL for testing in the NASA Langley Research Center (LaRC) 14 by 22-Foot Subsonic Tunnel (14x22) and other wind tunnels as deemed appropriate by the research community such as the Qinetiq 5 Meter tunnel.

Jared S. Fell↗
NASA NTRS2008

Effect of Excess Lead and Bismuth Content on the Electrical Properties of High-Temperature Bismuth Scandium Lead Titanate Ceramics

Aeronautic and aerospace applications require piezoelectric materials that can operate at high temperatures. The air-breathing aeronautic engines can use piezoelectric actuators for active combustion control for fuel modulation to mitigate thermo-acoustic instabilities and/or gas flow control to improve efficiency. The principal challenge for the insertion of piezoelectric materials is their limitation for upper use temperature and this limitation is due low Curie temperature and increasing conductivity. We investigated processing, microstructure and property relationship of (1-x)BiScO3-(x)PbTiO3 (BS-PT) composition as a promising high temperature piezoelectric. The effect of excess Pb and Bi and their partitioning in grain boundaries were studied using impedance spectroscopy, ferroelectric, and piezoelectric measurement techniques. Excess Pb addition increased the grain boundary conduction and the grain boundary area (average grain size was 24.8 m, and 1.3 m for compositions with 0at.% and 5at.% excess Pb, respectively) resulting in ceramics with higher AC conductivity (tan d= 0.9 and 1.7 for 0at.% and 5at.% excess Pb at 350 C and at 10kHz) that were not resistive enough to pole. Excess Bi addition increased the resistivity (rho= 4.1x10(exp 10) Omega cm and 19.6 x10(exp 10) Omega.cm for compositions with 0at.% and 5at.% excess Bi, respectively), improved poling, and increased the piezoelectric coefficient from 137 to 197 pC/N for 5at.% excess Bi addition. In addition, loss tangent decreased more than one order of magnitude at elevated temperatures (greater than 300 C). For all compositions the activation energy of the conducting species was similar (approximately equal to 0.35-0.40 eV) and indicated electronic conduction.

Sehirlioglu, Alp↗
NASA NTRS1980

A facility for testing the acoustic combustion instability characteristics of solid rocket propellants

A facility is described that has been specifically designed for small-scale laboratory testing of solid rocket propellants. A description of the facility is provided which includes the general plan of the facility and features related to personnel safety. One of the major activities in the facility is testing solid rocket propellants for combustion response to acoustic perturbations. A detailed discussion of acoustic instability testing is given including specially designed combustion apparatus, data acquisition, and signal conditioning. Techniques of data reduction are reviewed and some of the instrumentation problems that arise in this type of testing are mentioned along with practical solutions.

Mathes, H. B.↗
NASA NTRS1984

The influence of combustion liner holes on noise production by ducted burners

The thermoacoustic energy conversion process in a turbulent flame is not yet sufficiently well understood to allow accurate prediction of the sound pressure field of even the simplest of laboratory burners. The present contribution is intended to be a step toward fuller understanding of this process. In particular, the possibility is explored that the source structure, in the form of the thermoacoustic efficiency spectrum, might be influenced by the acoustic response of the burner itself. Experimental results are presented which seem to establish that, at least for the gas-fueled laboratory burner studied, source activity is not affected by the addition of downstream combustion liner holes which otherwise alter the acoustic response of the burner.

Mahan, J. R.↗