Results for “active flow control” — Page 11

NASA NTRS2016

Dynamic Stall Suppression Using Combustion-Powered Actuation (COMPACT)

Retreating blade stall is a well-known phenomenon that limits rotorcraft speed, maneuverability, and efficiency. Airfoil dynamic stall is a simpler problem, which demonstrates many of the same flow phenomena. Combustion Powered Actuation (COMPACT) is an active flow control technology, which at the outset of this work, had been shown to mitigate static and dynamic stall at low Mach numbers. The attributes of this technology suggested strong potential for success at higher Mach numbers, but such experiments had never been conducted. The work detailed in this report documents a 3-year effort focused on assessing the effectiveness of COMPACT for dynamic stall suppression at freestream conditions up to Mach 0.5. The work done has focused on implementing COMPACT on a high-lift rotorcraft airfoil: the VR-12. This selection was made in order to ensure that any measured benefits are over and above the capabilities of state-of-the-art high-lift rotorcraft airfoils. The detailed Computational Fluid Dynamics (CFD) simulations, wind-tunnel experiments, and system-level modeling conducted have shown the following: (1) COMPACT, in its current state of development, is capable of reducing the adverse effects of deep dynamic stall at Mach numbers up to 0.4; (2) The two-dimensional (2D) CFD results trend well compared to the experiments; and (3) Implementation of the CFD results into a system-level model suggest that significant rotor-level benefits are possible.

Matalanis, Claude G.↗

NASA NTRS2016

Aerospace Applications of Non-Equilibrium Plasma

Nonequilibrium plasma/non-thermal plasma/cold plasmas are being used in a wide range of new applications in aeronautics, active flow control, heat transfer reduction, plasma-assisted ignition and combustion, noise suppression, and power generation. Industrial applications may be found in pollution control, materials surface treatment, and water purification. In order for these plasma processes to become practical, efficient means of ionization are necessary. A primary challenge for these applications is to create a desired non-equilibrium plasma in air by preventing the discharge from transitioning into an arc. Of particular interest is the impact on simulations and experimental data with and without detailed consideration of non-equilibrium effects, and the consequences of neglecting non-equilibrium. This presentation will provide an assessment of the presence and influence of non-equilibrium phenomena for various aerospace needs and applications. Specific examples to be considered will include the forward energy deposition of laser-induced non-equilibrium plasmoids for sonic boom mitigation, weakly ionized flows obtained from pulsed nanosecond discharges for an annular Hall type MHD generator duct for turbojet energy bypass, and fundamental mechanisms affecting the design and operation of novel plasma-assisted reactive systems in dielectric liquids (water purification, in-pipe modification of fuels, etc.).

Nonequilibrium Plasma↗

NASA NTRS2017

Lattice Boltzmann for Airframe Noise Predictions

Increase predictive use of High-Fidelity Computational Aero- Acoustics (CAA) capabilities for NASA's next generation aviation concepts. CFD has been utilized substantially in analysis and design for steady-state problems (RANS). Computational resources are extremely challenged for high-fidelity unsteady problems (e.g. unsteady loads, buffet boundary, jet and installation noise, fan noise, active flow control, airframe noise, etc) ü Need novel techniques for reducing the computational resources consumed by current high-fidelity CAA Need routine acoustic analysis of aircraft components at full-scale Reynolds number from first principles Need an order of magnitude reduction in wall time to solution!

Barad, Michael↗

NASA NTRS2018

Numerical Simulation of a Simplified High-Lift CRM Configuration Embedded with Fluidic Actuators

Numerical simulations have been performed for a simplified high-lift configuration that is representative of a modern transport airplane. This configuration includes a leading-edge slat, fuselage, wing, nacelle-pylon and a simple hinged flap. The suction surface of the flap is embedded with multiple rows of fluidic actuators to reduce the extent of reversed flow regions and improve the aerodynamic performance of the configuration with flap in a deployed state. In the current paper, a Lattice Boltzmann Method based high-fidelity computational fluid dynamics (CFD) code, known as PowerFLOW® is used to simulate the entire flow field associated with this configuration, including the flow inside the actuators. A fully compressible version of the PowerFLOW® code that has been validated for high speed flows is used for the present simulations to accurately represent the transonic flow regimes that are encountered in the flow field generated by the actuators operating at higher mass flow (momentum) rates required to mitigate reverse flow regions on the suction surfaces of the main wing and the flap. The numerical solutions predict the expected trends in aerodynamic forces as the actuation levels are increased. More efficient active flow control (AFC) systems and actuator arrangement for lift augmentation are emerging based on the parametric studies conducted here prior to wind tunnel tests. These numerical solutions will be compared with experimental data, once such data becomes available.

Vatsa, Veer N.↗

NASA NTRS2015

Visualization of a Sweeping Jet by Laser Speckle Retro-reflective Background Oriented Schlieren

Sweeping jet actuators are currently being studied as a method of active flow control to increase the performance of wings and tails. Computational Fluid Dynamics simulations show that the jet does not sweep at a constant rate, instead spending more time at the minimum and maximum of its extent. As part of a test done to provide dynamic flow measurements for Computation Fluid Dynamics validation in NASA Ames Fluid Mechanics Lab, Particle Image Velocimetry (PIV) was performed on a single sweeping jet actuator designed by NASA and Boeing that was inset in a small airfoil. However, even at low jet pressures, the PIV could not be acquired at high enough frequencies to both spatially and temporally resolve the stickiness of the jet motion. Therefore, a small portion of the PIV laser was picked off and used to acquire flow visualization at higher frequencies through a new technique, laser speckle Retroreflective Background Oriented Schlieren (RBOS).

sweeping jet actuator↗

NASA NTRS2019

Surface Flow Visualization of the High-Lift Common Research Model

A 10% scale version of the High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The CRM-HL experiment included various configurations such as conventional and simple-hinged flaps, with and without engine nacelle/pylon, with and without nacelle chine, different Active Flow Control (AFC) methods (sweeping jets, alternating pulsed jets, and preconditioned boundary layer blowing), and their various parameters. This particular study is focused on the surface flow visualization of the conventional CRM-HL model at landing configuration. The conventional CRM-HL model with the single-slotted Fowler flap system serves as a baseline for the AFC-enabled simplified high-lift configuration as well as a high-lift technology development platform due to its publicly open geometry. Surface flow visualizations were performed using fluorescent minitufts, which were found to be nonintrusive to the aerodynamic performance. Tuft flow visualizations are supplemented with the relevant pressure and force measurements in order to understand the flow characteristics developed on the conventional CRM- HL model. In addition, three dimensional, unsteady, compressible Computational Fluid Dynamic (CFD) simulations were performed for selective cases. The surface streamlines and transverse velocity fluctuations obtained by the CFD simulations are qualitatively compared to the tuft direction and tuft unsteadiness, respectively. Force measurements of the CRM-HL model show performance degradation at higher angles of attack. Surface flow visualizations revealed the performance loss due to the nacelle/pylon wake that grows with angle of attack and eventually promotes flow separation over the inboard wing. This performance loss was successfully recovered by placing a chine on the engine nacelle.

Koklu, Mehti↗

NASA NTRSDate not supplied

Mitigation of Nacelle/Pylon Wake on the High-Lift Common Research Model Using a Nacelle Chine

A 10% scale, high-lift version of the Common Research Model (CRM-HL) was tested in the NASA Langley Research Center 14-by22-Foot Subsonic Tunnel. The focus of the wind tunnel test campaign was to assess the feasibility of active flow control (AFC) on the simplified CRM-HL configuration. The modular design of the CRM-HL model enabled the testing of the conventional CRM-HL version to establish a benchmark for the AFC research. The wind tunnel model has the capability of being tested with and without the engine nacelle/pylon for comparison. The wind tunnel investigation included the acquisition of force and moment data, steady pressure data, as well as surface flow visualization using minitufts. For some select cases, numerical simulations were performed to aid in understanding the wind tunnel data. Wind tunnel measurements indicated a lift degradation of the conventional CRM-HL at high angles of attack. The surface flow visualization with fluorescent minitufts revealed that the lift degradation is due to flow separation caused by the nacelle/pylon wake on the inboard wing. The wake and the consequent flow separation were successfully mitigated using a nacelle chine installed on the inboard side of the engine nacelle.

Mehti Koklu↗

NASA NTRSDate not supplied

CFD and Experimental Data Comparisons for Conventional and AFC-Enabled CRM High-Lift Configurations

Numerical simulations have been performed for a simplified high-lift (SHL) version of the Common Research Model (CRM) configuration, where the Fowler flaps of a representative conventional high-lift (CRM-HL) configuration are replaced by a set of simple hinged flaps. These hinged flaps are equipped with integrated modular active flow control (AFC) cartridges on the suction surface of the flap shoulder, and the resulting geometry is known as the CRM-SHL-AFC configuration. The main objective is to make use of AFC devices on the CRM-SHL-Configuration to produce the aerodynamic performance (lift) comparable to that of the CRM-HL configuration over a large angle of attack range encompassing maximum lift conditions. For comparison purposes, computations are also per-formed for the CRM-HL configuration. In the current paper, PowerFLOWR©, a CFD code based on the Lattice Boltzmann method (LBM), is used to simulate the entire flow field associated with the CRM-SHL-AFC configuration equipped with a combination of two different types of AFC actuators. The transonic version of the PowerFLOWR© code that has been validated for high-speed flows is used to simulate the flow field generated by the high-momentum actuators required to mitigate reversed flow regions on the suction surfaces of the main wing and the flap. This study is focused on the AFC systems and actuator arrangements that had emerged based on the parametric studies conducted previously at the nominal landing condition. Comparisons of the numerical solutions for lift and surface pressures are presented here with the experimental data, demonstrating the usefulness of CFD for predicting the flow field and lift characteristics of AFC-enabled high-lift configurations over a broad angle of attack range. The numerical solutions predict the expected trends in aerodynamic forces with angle of attack variation.

Veer N Vatsa↗

NASA NTRSDate not supplied

CFD Simulations of Landing and Takeoff CRM High-Lift Configurations

Numerical simulations have been performed for a conventional high-lift version of the Common Research Model (CRM) model corresponding to landing and take- off configurations. Computed values of lift and drag for the landing configuration are compared with the experimental data acquired in the 14- by 22-Foot Subsonic Tunnel (14×22) at the NASA Langley Research Center (LaRC). Simulations replicated the experimentally observed improvements in the lift characteristics in the presence of a nacelle chine. Flow visualization images indicate that vortices generated by the nacelle chine reduce flow separation regions on the upper surface of the wing at higher angles of attack. Based on such observations, the take-off configuration considered is also equipped with a nacelle chine, and testing of this configuration is planned in the 14×22 tunnel in near future. Preliminary solutions are also presented to explore the feasibility of using a localized flap gap blowing (LFGB) active flow control concept for improving the aerodynamic performance at take-off conditions.

aerodynamics↗

NASA NTRSDate not supplied

CFD Simulations of Landing and Takeoff CRM High-Lift Configurations

Numerical simulations have been performed for a conventional high-lift version of the Common Research Model (CRM) model corresponding to landing and take- off configurations. Computed values of lift and drag for the landing configuration are compared with the experimental data acquired in the 14- by 22-Foot Subsonic Tunnel (14×22) at the NASA Langley Research Center (LaRC). Simulations replicated the experimentally observed improvements in the lift characteristics in the presence of a nacelle chine. Flow visualization images indicate that vortices generated by the nacelle chine reduce flow separation regions on the upper surface of the wing at higher angles of attack. Based on such observations, the take-off configuration considered is also equipped with a nacelle chine, and testing of this configuration is planned in the 14×22 tunnel in near future. Preliminary solutions are also presented to explore the feasibility of using a localized flap gap blowing (LFGB) active flow control concept for improving the aerodynamic performance at take-off conditions.

aerodynamics↗

NASA NTRSDate not supplied

Scoping of an Air Supply Configuration for AFC on a Commercial Transport Airplane High Lift System

A scoping study is being conducted on the air supply for a microjet-based active flow control (AFC) system on a twin-turbofan commercial transport airplane. Microjets provide circulation control using small surface-normal pneumatic jets located near the trailing edge of a lifting surface such as a wing or flap. When located on the pressure side of the lifting surface they increase the lift, and when located on the suction side they decrease lift. In this study, microjets are considered for installation in the flaps of the high-lift version of the Common Research Model (CRM-HL). An air supply system involving bleed air from the airplane’s auxiliary power unit (APU) plus ram air provides the air to the microjets. A model based on the 1D compressible flow equations is applied to analyze the air supply system configuration and predict the microjet flow rate with the resulting airplane performance changes based on Reynolds-averaged Navier-Stokes modeling of microjets on the CRM-HL. The results of this scoping study are encouraging in that APU air can be used to entrain ram air and thereby increase the AFC mass flow rate to achieve effective lift control and airplane performance enhancement during takeoff and landing.

AATT↗

NASA NTRSDate not supplied

Scoping of an Air Supply Configuration for AFC on a Commercial Transport Airplane High Lift System

A scoping study is being conducted on the air supply fora microjet-based active flow control (AFC) system on a twin-turbofan commercial transport airplane. Microjets provide circulation control using small surface-normal pneumatic jets located near the trailing edge of a lifting surface such as a wing or flap. When located on the pressure side of the lifting surface they increase the lift, and when located on the suction side they decrease lift. In this study, microjets are considered for installation in the flaps of the high-lift version of the Common ResearchModel (CRM-HL). Two different architectures to supply the air for the microjets are considered: (1) bleed air from the airplane’s auxiliary power unit (APU) plus ram air, and (2) engine fan bleed air plus ram air. A model based on the 1D compressible flow equations is applied to analyze the air supply system architectures and predict the microjet flow rate with the resulting airplane performance changes based on Reynolds-averaged Navier-Stokes modeling of microjets on the CRM-HL. The results of this scoping study are encouraging in that pressurized air from the APU or the engine fan can be used to entrain ram air and thereby increase the AFC mass flow rate to achieve effective lift control and airplane performance enhancement during takeoff and landing.

AATT↗

NASA NTRSDate not supplied

Testing of High-Lift Common Research Model at Takeoff Configurations

The 10% scale High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The main objective of the wind tunnel test was to improve the aerodynamic performance of a representative aircraft model during takeoff operations using localized active flow control (AFC). This approach involves the application of AFC concepts locally to a relatively small region; therefore, it has the potential to cause minimal architectural change to current aircraft configurations. In addition, the power requirements of localized AFC could be supplied with onboard air resources. Recent exploratory studies identified the aileron as a target area for improving lift-to-drag ratio using localized AFC concepts. The idea is to deflect the ailerons beyond their nominal deflection angles and use AFC to reduce flow separation that occurs at larger aileron deflections. Several AFC concepts with different configurations were evaluated with the goal of achieving high-lift performance improvement. The assessment of AFC configurations is reported in a companion paper. The focus of the current paper is to report the data relevant to the CRM-HL takeoff configurations and establish a reference case for localized AFC application. Three takeoff configurations —reference, nominal, and high-lift improved—are documented. These takeoff configurations are obtained by varying aileron deflection. Wind tunnel measurements including surface static pressures and force and moment data are presented. In addition, surface tuft flow visualization, mainly on the aileron, is provided to understand the flow characteristics developed over the aileron during takeoff.

Lift-to-Drag↗

NASA NTRSDate not supplied

Testing of High-Lift Common Research Model at Takeoff Configurations

The 10% scale High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The main objective of the wind tunnel test was to improve the aerodynamic performance of a representative aircraft model during takeoff operations using localized active flow control (AFC). This approach involves the application of AFC concepts locally to a relatively small region; therefore, it has the potential to cause minimal architectural change to current aircraft configurations. In addition, the power requirements of localized AFC could be supplied with onboard air resources. Recent exploratory studies identified the aileron as a target area for improving lift-to-drag ratio using localized AFC concepts. The idea is to deflect the ailerons beyond their nominal deflection angles and use AFC to reduce flow separation that occurs at larger aileron deflections. Several AFC concepts with different configurations were evaluated with the goal of achieving high-lift performance improvement. The assessment of AFC configurations is reported in a companion paper. The focus of the current paper is to report the data relevant to the CRM-HL takeoff configurations and establish a reference case for localized AFC application. Three takeoff configurations —reference, nominal, and high-lift improved—are documented. These takeoff configurations are obtained by varying aileron deflection. Wind tunnel measurements including surface static pressures and force and moment data are presented. In addition, surface tuft flow visualization, mainly on the aileron, is provided to understand the flow characteristics developed over the aileron during takeoff.

Wind tunnel test↗

NASA NTRSDate not supplied

Wind Tunnel Experiment of Microjet-based Flow Control on a Multi-Element High-Lift Airfoil

A wind tunnel model was designed, manufactured, and tested to evaluate the potential of active aerodynamic flow control for multi-element airfoils. The active flow control system involves so-called microjets –small, low momentum, normal to the surface jets located near the trailing edge of the flap –for controlling the lift and improving the aerodynamic performance characteristics of airplane high-lift systems. The configuration selected for this test is the NLR7301 two-element airfoil and it was tested in the Oran W. Nicks Low-Speed Wind Tunnel at Texas A&M University at a chord Reynolds number of 2.0 million and Machnumber of 0.10. This paper presents wind tunnel results for the NLR7301 in the Flap 20 and Flap 30 configurations. The wind tunnel results include surface pressure distributions, lift and pitching moment, and flow visualizations.The results of this experiment validate the effectiveness of the microjet with regards to control of lift in the linear regime for multi-element airfoils.

ARMD↗

NASA NTRS1985

Active control of compressible flows on a curved surface

The effect of localized, time periodic surface heating and cooling over a curved surface is studied. This is a mechanism for the active control of unstable disturbances by phase cancellation and reinforcement. It is shown that the pressure gradient induced by the curvature significantly enhances the effectiveness of this form of active control. In particular, by appropriate choice of phase, active surface heating can completely stabilize and unstable wave.

Maestrello, L.↗

NASA NTRS1985

Active control of compressible flows on a curved surface

The effect of localized, time periodic surface heating and cooling over a curved surface is studied. This is a mechanism for the active control of unstable disturbances by phase cancellation and reinforcement. It is shown that the pressure gradient induced by the curvature significantly enhances the effectiveness of this form of active control. In particular, by appropriate choice of phase, active surface heating can completely stabilize an unstable wave.

Maestrello, L.↗

DOE OSTI2025

Closed-Loop Control of Active Nematic Flows

Stabilizing and shaping autonomous flows of active fluids is a fundamental challenge and a prerequisite for applications. We embed a light-responsive microtubule-based nematic in a proportional-integral control loop that adjusts the applied light intensity in response to real-time measurements of the spatially averaged flow speed. The self-regulating hardware-software-wetware system maintains a target flow speed against external or internal perturbations, including protein aging and aggregation, sample-to-sample variability, and temperature variation. Varying the controller’s gains reveals antagonistic roles between feedback and intrinsic processes, leading to nontrivial dynamics observed in fluctuation spectra. In particular, oscillations emerge from the interplay between the controller, motor binding kinetics, and active hydrodynamic relaxation. Accounting for the underlying binding timescale, our coarse-grained model and nematohydrodynamics simulations corroborate these observations. This work provides insight into the coupled dynamics of controlled active matter, laying the foundation for spatiotemporal patterning of active stress to generate and stabilize new dynamical configurations.

Active nematics↗