Search NASA⌕ Search

SEARCH · Search NASA

Results for “aeroelastic comparison”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Aeroelastic Calculations Using CFD for a Typical Business Jet Model

Two time-accurate Computational Fluid Dynamics (CFD) codes were used to compute several flutter points for a typical business jet model. The model consisted of a rigid fuselage with a flexible semispan wing and was tested in the Transonic Dynamics Tunnel at NASA Langley Research Center where experimental flutter data were obtained from M(sub infinity) = 0.628 to M(sub infinity) = 0.888. The computational results were computed using CFD codes based on the inviscid TSD equation (CAP-TSD) and the Euler/Navier-Stokes equations (CFL3D-AE). Comparisons are made between analytical results and with experiment where appropriate. The results presented here show that the Navier-Stokes method is required near the transonic dip due to the strong viscous effects while the TSD and Euler methods used here provide good results at the lower Mach numbers.

Gibbons, Michael D.↗
NASA NTRS1990

Experience with scale effects in non-airplane wind tunnel testing

The aerodynamics results of two tests performed in the 80- by 120-Foot Wind Tunnel at NASA Ames Research Center are discussed with particular emphasis on the effects of model scale. The tests are unusual for this facility in that they were performed on non-airplane configurations: a full-scale tractor/trailer and large ramair inflated wings. For the truck drag measurements, comparisons with 1/8th-scale drag data taken at the Low Speed Wind Tunnel at Texas A&M indicate that small scale measurements can provide adequate accuracy if care is taken to test at high enough Reynolds numbers and if large regions of separated flow and reattachment are avoided. Some of the important aerodynamic and structural aspects of parafoil testing are also discussed. These include the effects of Reynolds number and aeroelastic effects such as fabric and support line stretch.

Ross, J. C.↗
NASA NTRS1991

Parallel computation of aerodynamic influence coefficients for aeroelastic analysis on a transputer network

Aeroelastic analysis is mult-disciplinary and computationally expensive. Hence, it can greatly benefit from parallel processing. As part of an effort to develop an aeroelastic analysis capability on a distributed-memory transputer network, a parallel algorithm for the computation of aerodynamic influence coefficients is implemented on a network of 32 transputers. The aerodynamic influence coefficients are calculated using a three-dimensional unsteady aerodynamic model and a panel discretization. Efficiencies up to 85 percent are demonstrated using 32 processors. The effects of subtask ordering, problem size and network topology are presented. A comparison to results on a shared-memory computer indicates that higher speedup is achieved on the distributed-memory system.

Janetzke, D. C.↗
NASA NTRS2002

Uncertainty of Videogrammetric Techniques used for Aerodynamic Testing

The uncertainty of videogrammetric techniques used for the measurement of static aeroelastic wind tunnel model deformation and wind tunnel model pitch angle is discussed. Sensitivity analyses and geometrical considerations of uncertainty are augmented by analyses of experimental data in which videogrammetric angle measurements were taken simultaneously with precision servo accelerometers corrected for dynamics. An analysis of variance (ANOVA) to examine error dependence on angle of attack, sensor used (inertial or optical). and on tunnel state variables such as Mach number is presented. Experimental comparisons with a high-accuracy indexing table are presented. Small roll angles are found to introduce a zero-shift in the measured angles. It is shown experimentally that. provided the proper constraints necessary for a solution are met, a single- camera solution can he comparable to a 2-camera intersection result. The relative immunity of optical techniques to dynamics is illustrated.

Burner, A. W.↗
NASA NTRS2012

An Assessment of CFD/CSD Prediction State-of-the-Art by Using the HART II International Workshop Data

Over the past decade, there have been significant advancements in the accuracy of rotor aeroelastic simulations with the application of computational fluid dynamics methods coupled with computational structural dynamics codes (CFD/CSD). The HART II International Workshop database, which includes descent operating conditions with strong blade-vortex interactions (BVI), provides a unique opportunity to assess the ability of CFD/CSD to capture these physics. In addition to a baseline case with BVI, two additional cases with 3/rev higher harmonic blade root pitch control (HHC) are available for comparison. The collaboration during the workshop permits assessment of structured, unstructured, and hybrid overset CFD/CSD methods from across the globe on the dynamics, aerodynamics, and wake structure. Evaluation of the plethora of CFD/CSD methods indicate that the most important numerical variables associated with most accurately capturing BVI are a two-equation or detached eddy simulation (DES)-based turbulence model and a sufficiently small time step. An appropriate trade-off between grid fidelity and spatial accuracy schemes also appears to be pertinent for capturing BVI on the advancing rotor disk. Overall, the CFD/CSD methods generally fall within the same accuracy; cost-effective hybrid Navier-Stokes/Lagrangian wake methods provide accuracies within 50% the full CFD/CSD methods for most parameters of interest, except for those highly influenced by torsion. The importance of modeling the fuselage is observed, and other computational requirements are discussed.

Smith, Marilyn J.↗
NASA NTRS1993

Acoustic radiation damping of flat rectangular plates subjected to subsonic flows

The acoustic radiation damping for various isotropic and laminated composite plates and semi-infinite strips subjected to a uniform, subsonic and steady flow has been predicted. The predictions are based on the linear vibration of a flat plate. The fluid loading is characterized as the perturbation pressure derived from the linearized Bernoulli and continuity equations. Parameters varied in the analysis include Mach number, mode number and plate size, aspect ratio and mass. The predictions are compared with existing theoretical results and experimental data. The analytical results show that the fluid loading can significantly affect realistic plate responses. Generally, graphite/epoxy and carbon/carbon plates have higher acoustic radiation damping values than similar aluminum plates, except near plate divergence conditions resulting from aeroelastic instability. Universal curves are presented where the acoustic radiation damping normalized by the mass ratio is a linear function of the reduced frequency. A separate curve is required for each Mach number and plate aspect ratio. In addition, acoustic radiation damping values can be greater than or equal to the structural component of the modal critical damping ratio (assumed as 0.01) for the higher subsonic Mach numbers. New experimental data were acquired for comparison with the analytical results.

Lyle, Karen Heitman↗
NASA NTRS1980

The prediction of pressure distributions on an arrow-wing configuration including the effect of camber, twist, and a wing fin

Wind tunnel tests of an arrow wing body configuration consisting of flat, twisted, and cambered twisted wings were conducted at Mach numbers from 0.40 to 2.50 to provide an experimental data base for comparison with theoretical methods. A variety of leading and trailing edge control surface deflections were included in these tests, and in addition, the cambered twisted wing was tested with an outboard vertical fin to determine its effect on wing and control surface loads. Theory experiment comparisons show that current state of the art linear and nonlinear attached flow methods were adequate at small angles of attack typical of cruise conditions. The incremental effects of outboard fin, wing twist, and wing camber are most accurately predicted by the advanced panel method PANAIR. Results of the advanced panel separated flow method, obtained with an early version of the program, show promise that accurate detailed pressure predictions may soon be possible for an aeroelasticity deformed wing at high angles of attack.

Bobbitt, P. J.↗
NASA NTRS2005

Aeroelastic Deformation: Adaptation of Wind Tunnel Measurement Concepts to Full-Scale Vehicle Flight Testing

The adaptation of a proven wind tunnel test technique, known as Videogrammetry, to flight testing of full-scale vehicles is presented. A description is presented of the technique used at NASA's Dryden Flight Research Center for the measurement of the change in wing twist and deflection of an F/A-18 research aircraft as a function of both time and aerodynamic load. Requirements for in-flight measurements are compared and contrasted with those for wind tunnel testing. The methodology for the flight-testing technique and differences compared to wind tunnel testing are given. Measurement and operational comparisons to an older in-flight system known as the Flight Deflection Measurement System (FDMS) are presented.

Burner, Alpheus W.↗
NASA NTRS2005

Aeroelastic Deformation: Adaptation of Wind Tunnel Measurement Concepts to Full-Scale Vehicle Flight Testing

The adaptation of a proven wind tunnel test technique, known as Videogrammetry, to flight testing of full-scale vehicles is presented. A description is presented of the technique used at NASA's Dryden Flight Research Center for the measurement of the change in wing twist and deflection of an F/A-18 research aircraft as a function of both time and aerodynamic load. Requirements for in-flight measurements are compared and contrasted with those for wind tunnel testing. The methodology for the flight-testing technique and differences compared to wind tunnel testing are given. Measurement and operational comparisons to an older in-flight system known as the Flight Deflection Measurement System (FDMS) are presented.

Burner, Alpheus W.↗
NASA NTRS1981

In-flight deflection measurement of the HiMAT aeroelastically tailored wing

An electro-optical flight deflection measurement system was developed for NASA for use on the highly maneuverable aircraft technology (HiMAT) remotely piloted research vehicle (RPRV) to provide a means of evaluating the performance of the HiMAT's aeroelastically tailored composite wing and canard. A description of the flight deflection measurement system is presented from a user's viewpoint and includes the general method of operation, system capabilities and limitations, method of installation on the HiMAT vehicle, and calibration of targets. Also included is a general description of the HiMAT RPRV and its design goals. Preliminary flight deflection and bending moment data were obtained at Mach 0.8 and were extrapolated to the Mach 0.9 maneuver design condition for comparison to NASTRAN predictions and ground loads test results. The preliminary flight test results tended to agree with the results obtained from the static ground loads tests, that is, that the NASTRAN model overpredicted the streamwise twist of the composite outer wing panel.

Deangelis, V. M.↗
NASA NTRS1989

Comparison of measured induced velocities with results from a closed-form finite state wake model in forward flight

An unsteady, three-dimensional induced-flow model is applied to compute the induced-flow distribution of a rotor in forward flight, and numerical results are compared against LDV measurements for both time-averaged and unsteady induced flow at the disk. The former flow shows good agreement with measured data, except just behind the pylon at the lowest advanced ratio and near the blade tips for rectangular blades at high advance ratios. The method performs as well or better than other codes that have been applied to these data, takes less computing time, and is better suited to aeroelastic analysis. Results with only four harmonics and 15 state variables converge to all fundamental characteristics of the time-averaged flow.

Peters, David A.↗
NASA NTRS1986

Loads calibrations of strain gage bridges on the DAST project Aeroelastic Research Wing (ARW-2)

Results from and details of the procedure used to calibrate strain gage bridges for measurements of wing structural loads, shear (V), bending moment (M), and torque (T), at three semispan stations on both the left and right semispans of the ARW-2 wing are presented. The ARW-2 wing has a reference area of 35 square feet, a span of 19 feet, an aspect ratio of 10.3, a midchord line sweepback angle of 25 degrees, and a taper ratio of 0.4. The ARW-2 wing was fabricated using aluminum spars and ribs covered with a fiberglass/honeycomb sandwich skin material. All strain gage bridges are mounted along with an estimate of their accuracy by means of a comparison of computed loads versus actual loads for three simulated flight conditions.

Eckstrom, C. V.↗
NASA NTRS1974

Dynamics of tilting proprotor aircraft in cruise flight

A nine degree-of-freedom theoretical model is developed for investigations of the dynamics of a proprotor operating in high inflow axial flight on a cantilever wing. The basic characteristics of the rotor high inflow aerodynamics and the resulting rotor aeroelastic behavior are discussed. The problems of classical whirl flutter, the two-bladed rotor, and the influence of the proprotor on the stability derivatives of the aircraft are treated briefly. The influence of various elements of the theoretical model is discussed, including the modeling used for the blade and wing aerodynamics, and the influence of the rotor lag degree of freedom. The results from tests of two full-scale proprotors - a gimballed, stiff-inplane rotor and a hingeless, soft-inplane rotor - are presented; comparisons with the theoretical results show good correlation.

Johnson, W.↗
NASA NTRS2015

Aeroelastic Analysis of a Flexible Wing Wind Tunnel Model with Variable Camber Continuous Trailing Edge Flap Design

This paper presents data analysis of a flexible wing wind tunnel model with a variable camber continuous trailing edge flap (VCCTEF) design for drag minimization tested at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel test was designed to explore the relative merit of the VCCTEF concept for improved cruise efficiency through the use of low-cost aeroelastic model test techniques. The flexible wing model is a 10%-scale model of a typical transport wing and is constructed of woven fabric composites and foam core. The wing structural stiffness in bending is tailored to be half of the stiffness of a Boeing 757-era transport wing while the torsional stiffness is about the same. This stiffness reduction results in a wing tip deflection of about 10% of the wing semi-span. The VCCTEF is a multi-segment flap design having three chordwise camber segments and five spanwise flap sections for a total of 15 individual flap elements. The three chordwise camber segments can be positioned appropriately to create a desired trailing edge camber. Elastomeric material is used to cover the gaps in between the spanwise flap sections, thereby creating a continuous trailing edge. Wind tunnel data analysis conducted previously shows that the VCCTEF can achieve a drag reduction of up to 6.31% and an improvement in the lift-to-drag ratio (L=D) of up to 4.85%. A method for estimating the bending and torsional stiffnesses of the flexible wingUWAL wind tunnel model from static load test data is presented. The resulting estimation indicates that the stiffness of the flexible wing is significantly stiffer in torsion than in bending by as much as 9 to 1. The lift prediction for the flexible wing is computed by a coupled aerodynamic-structural model. The coupled model is developed by coupling a conceptual aerodynamic tool Vorlax with a finite-element model of the flexible wing via an automated geometry deformation tool. Based on the comparison of the lift curve slope, the lift prediction for the rigid wing is in good agreement with the estimated lift coefficients derived from the wind tunnel test data. Due to the movement of the VCCTEF during the wind tunnel test, uncertainty in the lift prediction due to the indicated variations of the VCCTEF deflection is studied. The results show a significant spread in the lift prediction which contradicts the consistency in the aerodynamic measurements, thus suggesting that the indicated variations as measured by the VICON system may not be reliable. The lift prediction of the flexible wing agrees very well with the measured lift curve for the baseline configuration. The computed bending deflection and wash-out twist of the flexible wing also match reasonably well with the aeroelastic deflection measurements. The results demonstrate the validity of the aerodynamic-structural tool for use to analyze aerodynamic performance of flexible wings.

Wind Tunnel↗
NASA NTRS2004

Rotor Airloads Prediction Using Loose Aerodynamic Structural Coupling

This work couples a computational fluid dynamics (CFD) code and rotorcraft computational structural dynamics (CSD) code to calculate helicopter rotor airloads across a range of flight conditions. An iterative loose (weak) coupling methodology is used to couple the CFD and CSD codes on a per revolution, periodic basis. The CFD uses a high fidelity, Navier-Stokes, overset grid methodology with first principles-based wake capturing. Modifications are made to the CFD code for aeroelastic analysis. For a UH-60A Blackhawk helicopter, four challenging level flight conditions are computed: 1) low speed (u = 0.15) with blade-vortex interaction, 2) high speed (u = 0.37) with advancing blade negative lift, 3) high thrust with dynamic stall (u = 0.24), and 4) hover. Results are compared with UH-60A Airloads Program fight test data. Most importantly, for all cases the loose coupling methodology is shown to be stable, convergent, and robust with full coupling of normal force, pitching moment, and chord force. In comparison with flight test data, normal force and pitching moment magnitudes are in good agreement. For the high speed and dynamic stall cases a phase lag in comparison with the data is seen, nonetheless, the shapes of the curves are very good. Overall, the results are noteworthy improvement over lifting line aerodynamics used in rotorcraft comprehensive codes.

Potsdam, Mark↗
NASA NTRSDate not supplied

NASA 5.2%-Scale High Lift Common Research Model (CRM-HL) Test in the National Transonic Facility (NTF)

Problem: Predicting CL,max and assessing transition, turbulence models, and Reynolds number effect predictions in CFD requires wind tunnel data for comparison. Objective: Expand the CFD validation database by running multiple models designed using the same reference geometry in various wind tunnels around the world. The wind tunnel data and model geometry will be open source to allow for CFD validation use. Approach: Run the NASA 5.2%-scale High Lift Common Research Model (CRM-HL) semi-span model at the National Transonic Facility (NTF). Test the model at chord Reynolds numbers (Rec) between 1.6 million and 30 million and at varying Q/Es to assess Reynolds number effects and aeroelasticity affects on the model, while collecting force and moment, pressure and wing deformation data. Test the model with ice shapes installed on the leading edges. Results: Ran eight model configurations, including four landing, two landing with ice shapes installed, and two takeoff configurations. Ran in air (120°F) and nitrogen operations (-50°F, -180°F and -250°F) at 7 different chord Reynolds numbers. The data compare well with previous tests of the same model at DLR (The Germany Aerospace Center) and the 14- by 22-Foot Subsonic Tunnel (14x22). Significance: Provided valuable high Reynolds number data on a high lift configuration to the worldwide research community. Provide icing data at flight Reynolds number to the research community.

CRM-HL↗
NASA NTRS1993

Aeroelastic response and stability of tiltrotors with elastically-coupled composite rotor blades

There is a potential for improving the performance and aeroelastic stability of tiltrotors through the use of elastically-coupled composite rotor blades. To study the characteristics of tiltrotors with these types of rotor blades it is necessary to formulate a new analysis which has the capabilities of modeling both a tiltrotor configuration and an anisotropic rotor blade. Background for these formulations is established in two preliminary investigations. In the first, the influence of several system design parameters on tiltrotor aeroelastic stability is examined for the high-speed axial flight mode using a newly-developed rigid-blade analysis with an elastic wing finite element model. The second preliminary investigation addresses the accuracy of using a one-dimensional beam analysis to predict frequencies of elastically-coupled highly-twisted rotor blades. Important aspects of the new aeroelastic formulations are the inclusion of a large steady pylon angle which controls tilt of the rotor system with respect to the airflow, the inclusion of elastic pitch-lag coupling terms related to rotor precone, the inclusion of hub-related degrees of freedom which enable modeling of a gimballed rotor system and engine drive-train dynamics, and additional elastic coupling terms which enable modeling of the anisotropic features for both the rotor blades and the tiltrotor wing. Accuracy of the new tiltrotor analysis is demonstrated by a comparison of the results produced for a baseline case with analytical and experimental results reported in the open literature. Two investigations of elastically tailored blades on a baseline tiltrotor are then conducted. One investigation shows that elastic bending-twist coupling of the rotor blade is a very effective means for increasing the flutter velocity of a tiltrotor, and the magnitude of coupling required does not have an adverse effect on performance or blade loads. The second investigation shows that passive blade twist control via elastic extension-twist coupling of the rotor blade has the capability of significantly improving tiltrotor aerodynamic performance. This concept, however, is shown to have, in general, a negative impact on stability characteristics.

Nixon, Mark W.↗
NASA NTRS1985

Implementation and verification of a comprehensive helicopter coupled rotor - Fuselage analysis

The analytical basis and the application of a Rotor/Airframe Comprehensive Aeroelastic Program (RACAP) are described in detail. The rationale behind each analytical choice is outlined and the modular procedure is described. The program is verified by application to the AH-1G helicopter. The applicability of various airload prediction models is examined, and both the steady and vibratory responses of the blade are compared with flight test data. Reasonable correlation is found between measured and calculated blade response, with excellent correlation for vibration amplitudes at various locations on the fuselage such as engine, pilot seat, and gunner. Within the analytical model, comparisons are drawn between an isolated blade analysis and a coupled rotor/fuselage model. The deficiency of the former in the context of the AH-1G is highlighted.

Wood, E. R.↗