Search NASA⌕ Search

SEARCH · Search NASA

Results for “arches”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Long-Length SiC/SiC Tube Irradiation Experiment at LWR Temperatures Inserted into HFIR

This report describes the pre-irradiation characterization and successful assembly of a High Flux Isotope Reactor (HFIR) irradiation experiment designed to assess radiation-induced lateral bowing of silicon carbide fiber–reinforced, silicon carbide matrix composite (SiC/SiC) components under a radial fast neutron flux gradient at representative light-water reactor (LWR) temperatures of approximately 300 °C. The over-arching goal of this work is to validate thermomechanical models of SiC/SiC composite fuel assembly distortion used to predict the extent of lateral bowing and dose at which bowing reaches a maximum value. Ultimately, these models are used to ensure that fuel assembly distortion does not block coolant channels, interfere with control rod/blade movements, and/or impact local reactivity. The experiment contains six cladding tube specimens that are approximately 558.5 mm long with representative pressurized water reactor (PWR) outer and inner diameters of 9.5 mm and 7.5 mm, respectively. The specimens were thoroughly characterized prior to irradiation using traditional dimensional inspection and surface profilometry so that these measurements can later be compared with similar measurements that will be made post-irradiation to determine radiation-induced deformations. Furthermore, fine engraving markers were inscribed along the outer surfaces of the specimen and mapped using analytic photography and a three-dimensional stage. This technique allowed for accurate measurements of the marker spacings, which can be compared with similar measurements that will be made post-irradiation to provide local radiation-induced strain mapping. A light curtain optical micrometer was also employed to measure the pre-irradiation bowing of each specimen. The experiment was successfully assembled and inserted into position VXF-19 for HFIR cycle 516, which began May 12, 2026. The experiment will be removed after cycle 519, which is currently scheduled to end in December 2026.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

EUI Benchmarks for Net-Zero Energy Buildings in India

In our study we present EUI benchmarks for NZEBs for six building types across residential and non-residential typologies and for India's five climate zones. This approach is similar to the simulation-based benchmarks used by the B3 program in Minnesota, the Cal-Arch methodology in California, and the US Solar Decathlon approach, which combine simulations with actual building data. Of the six building types we explore one in detail with a range of operation scenarios, specifically narrowing down the EUI benchmarks for mixed-mode building operation and for variable temperature set-points as prescribed in the National Building Code of India.The contribution of this work is to provide rigorous end-use level EUI benchmarks for six building types, and to describe a method for simulation-based EUI benchmarks for mixed-mode operation with variable setpoints to highlight the difference between the standard approach used for the five building types and the On-Site Construction Worker Housing which additionally has the mixed-mode variable setpoint approach.On-Site Construction Worker Housings are typically poorly constructed temporary structures, without adequate thermal comfort, It is critical to provide adequate thermal comfort to protect people from the warming effects of climate change, and to discover super efficient and cost-effective ways to do so.The methodology used for the On-Site Construction Worker Housing (CWH) results in an 80% acceptability according to the India Model for Adaptive Comfort in the National Building Code of India. EUIs of all six buildings are 60% lower than the minimum compliance with India's Energy Conservation Building Codes, providing benchmarks for efficiency levels. The end-use level EUI benchmarks are now provided to over 1800 Solar Decathlon India participants so that they can compare the performance of their NZEB designs.In particular, the CWH results provide an insight into the importance of the mixed-mode operation with variable temperature set-points. The results from the simulation study show that for an NZEB target, the EUI with standard thermal comfort model and without mixed operation is 58.26 kWh/m2*year, while that with the variable set-points of the adaptive model with mixed mode operation is 24.23 kWh/m2*year. This is a 58% reduction in EUI. Given that many building types including residential, and non-residential operate in mixed mode, it is important to take this work further to develop mixed-mode operation NZEB benchmarks so that the carbon intensity of these buildings could be lower than the standard thermal comfort model approach.

benchmarking↗
DOE OSTI2023

Finite element modeling of biomass hopper flow

Hoppers are widely used biomass handling devices that channel bulk biomass from storage to subsequent handling equipment. Jenike’s longstanding approach, based on the Mohr-Coulomb model, has been successfully used to design hoppers handling cohesionless granular materials such as grains and other agricultural produces. However, designing a hopper to ensure reliable biomass flow is found to be challenging due to cohesion, irregular particle shape, and bulk material elastoplasticity. This study aims to address the biomass handling engineering challenge with alternative constitutive material models concerning the flow behavior of bulk solids. Finite element modeling is an approach that allows for implementation of different material models, whose underlying constitutive theories assist in investigating the origin and manifestation of bulk mechanical behavior of granular materials. This study focuses on the incipient gravity hopper flow of two types of biomass feedstocks, i.e., ground corn stover and Douglas fir wood. Three widely used constitutive material models, i.e., Mohr-Coulomb model, modified Cam-Clay model, and Drucker-Prager/Cap model, are implemented. Using the flow pattern represented by the volume of biomass exhibiting more than 7% of axial strain (Kamath and Puri, 1999), the finite element model predicts that the bulk corn stover particulate material forms an arch, which represents a hampered transition from the static state to the dynamic flow-state out of the hopper, whereas bulk Douglas fir wood particulate material develops a reliable mass flow pattern. A laboratory scale hopper was used to experimentally determine the biomass flow conditions, which were subsequently compared with the predicted onset of flow by a finite element model (FEM). The developed FEM was found to correctly predict the initiation of mass flow for the milled Douglas fir wood, whereas corn stover was predicted to establish a strong core flow suggesting an unreliable handling characteristic. This observation aligns with the reported poor handling of milled corn stover.

09 BIOMASS FUELS↗
DOE OSTI2022

Explanation and Application of the Evolving Contact Traction Fields in Shallow Foundation Systems

The present paper provides a qualitative discussion of the evolution of contact traction fields beneath rigid shallow foundations resting on granular materials. A phenomenological similarity is recognized in the measured contact traction fields of rigid footings and at the bases of sandpiles. This observation leads to the hypothesis that the stress distributions are brought about by the same physical phenomena, namely the development of arching effects through force chains and mobilized intergranular friction. A set of semi-empirical equations are suggested for the normal and tangential components of this contact traction based on past experimental measurements and phenomenological assumptions of frictional behaviors at the foundation system scale. These equations are then applied to the prescribed boundary conditions for the analysis of the settlement, resistance, and stress fields in supporting granular materials beneath the footing. A parametric sensitivity study is performed on the proposed modelling method, highlighting solutions to the boundary-value problems in an isotropic, homogeneous elastic half-space.

42 ENGINEERING↗
DOE OSTI2021

Laboratory Study of the Torus Instability Threshold in Solar-relevant, Line-tied Magnetic Flux Ropes

Coronal mass ejections (CMEs) occur when long-lived magnetic flux ropes (MFRs) anchored to the solar surface destabilize and erupt away from the Sun. This destabilization is often described in terms of an ideal magnetohydrodynamic instability called the torus instability. It occurs when the external magnetic field decreases sufficiently fast such that its decay index, ${n}_{}=-z\,\partial (\mathrm{ln}{B}_{})/\partial z$, is larger than a critical value, $n\gt {n}_{\mathrm{cr}}^{}$, where ${n}_{\mathrm{cr}}^{}=1.5$ for a full, large aspect ratio torus. However, when this is applied to solar MFRs, a range of conflicting values for ${n}_{\mathrm{cr}}^{}$ is found in the literature. To investigate this discrepancy, we have conducted laboratory experiments on arched, line-tied flux ropes and applied a theoretical model of the torus instability. Our model describes an MFR as a partial torus with foot points anchored in a conducting surface and numerically calculates various magnetic forces on it. This calculation yields better predictions of ${n}_{\mathrm{cr}}^{}$ that take into account the specific parameters of the MFR. Here, we describe a systematic methodology to properly translate laboratory results to their solar counterparts, provided that the MFRs have a sufficiently small edge safety factor or, equivalently, a large enough twist. After this translation, our model predicts that ${n}_{\mathrm{cr}}^{}$ in solar conditions falls near ${n}_{\mathrm{cr}}^{\mathrm{solar}}\sim 0.9$ and within a larger range of ${n}_{\mathrm{cr}}^{\mathrm{solar}}\sim (0.7,1.2)$, depending on the parameters. The methodology of translating laboratory MFRs to their solar counterparts enables quantitative investigations of CME initiation through laboratory experiments. These experiments allow for new physics insights that are required for better predictions of space weather events but are difficult to obtain otherwise.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1961

Theory of Electrostatic Fields in the Ionosphere at Equatorial Latitudes

The properties of the elongated electrostatic fields that are required to provide the coupling mechanism in the dynamo-motor concept of the E and F regions of the ionosphere are examined theoretically for the conditions that prevail in equatorial latitudes. The analysis is developed for an electrostatic field of arbitrary horizontal scale in a horizontally stratified partly ionized gas subject to an imposed magnetic field having the form of a parabolic arch over the equator. The anisotropic character and continuous variation with height of the conductivity are retained throughout , and numerical solutions are determined for the attenuation of the electric field with distance along the field line. The results are similar qualitatively to those found previously upon analysis of the corresponding problem for middle latitudes, but the attenuation of the electrostatic field with height is considerably greater. It develops, in particular, that the coupling between E and F regions is very small for fields having horizontal wavelengths of a few kilometers. It follows that the dynamo-motor concept could not be used to account for the presence of irregularities of this scale. On the other hand, it is found that almost all the attenuation occurs at heights near that of the E region. If an electrostatic field having a horizontal wavelength of a few kilometers could be produced at heights of, say 200 km or greater, it follows that it would be very elongated and extend with little change in amplitude from hemisphere to hemisphere. The results also indicate that effective coupling could be achieved for fields having horizontal wavelengths of the order of tens of kilometers, but the assumptions introduced to simplify the analysis may impair the quantitative reliability of the results for fields of this scale.

Briggs, Benjamin R.↗
NASA NTRS1970

Flexible electrical conductors for high-temperature switchgear

Arch-shaped conductors fabricated from flat strips of beryllium oxide dispersion-strengthened copper alloy serve as flexible electrical connectors capable of operating in 1000 deg F temperature range, under vacuum conditions for periods of 10,000 hours or more without failure.

Koutnik, E. A.↗
NASA NTRS1972

Identification of geostructures of continental crust, particularly as they relate to mineral-resource evaluation

The authors have identified the following significant results. As a precursor to the ERTS-1 investigation, the spatial relationship of geostructures seen on Nimbus IDCS photographs to the distribution of mineralized areas in Alaska and western Canada was analyzed to determine the possible metallogenic significance of the geostructures. In Canada, mercury and porphyry molybdenum deposits are closely associated with strong northwest-trending fault systems; the development of mineralized regions seems related to major crustal zones or fractures trending southwestward across the Cordillera from the Precambrian shield. In Alaska, comparison of the northeast- and northwest-trending set of possible crustal structures shown on the Nimbus photo, with the distribution of known mineral deposits suggests a similar relationship. The mineralized region of massive sulfides in Prince William Sound and upper Copper River areas and of porphyry coppers in the Nabesna area forms a broad northeast-trending belt possibly related to the Minto Arch on the Shield. The belt of metalliferous deposits in the western Alaska Range follows a comparable northeast trend. Mercury deposits, suggested by many to be fault-controlled, together with most tin and tungsten deposits, occupy a northeast-trending belt between the Bristol Bay-Mackenzie Bay linear and extensions of a linear along the lower Yukon River. This belt intersects the northwest-trending Canadian belt of similar deposits in the Fairbanks area.

Gryc, G.↗
NASA NTRS1972

A model for predicting aortic dynamic response to -G sub z impact acceleration.

A steady state dynamic response model for the radial motion of the aorta is developed from in vivo pressure-displacement and nerve stimulation experiments on canines. The model represented by a modified Van der Pol wave motion oscillator closely predicts steady state and perturbed response results. The applicability of the steady state canine aortic model to tailward acting impact forces is studied by means of the perturbed phase plane of the oscillator. The backflow through the aortic arch resulting from a specified acceleration-time profile is computed and an analysis for predicting the forced motion aortic response is presented.

Advani, S. H.↗
NASA NTRS1972

Coronal magnetic fields and the solar wind

Current information is presented on coronal magnetic fields as they bear on problems of the solar wind. Both steady state fields and coronal transient events are considered. A brief critique is given of the methods of calculating coronal magnetic fields including the potential (current free) models, exact solutions for the solar wind and field interaction, and source surface models. These solutions are compared with the meager quantitative observations which are available at this time. Qualitative comparisons between the shapes of calculated magnetic field lines and the forms visible in the solar corona at several recent eclipses are displayed. These suggest that: (1) coronal streamers develop above extended magnetic arcades which connect unipolar regions of opposite polarity; and (2) loops, arches, and rays in the corona correspond to preferentially filled magnetic tubes in the approximately potential field.

Newkirk, G., Jr.↗
NASA NTRS1972

What makes active regions grow.

A study of magnetic flux growth or growth failure in over 100 active regions is shown to indicate that most growth is connected with the emergence of a large batch of flux in the shape of a new arch filament system (AFS). During the recent sunspot maximum, new AFSs appeared at a rate of nearly one per day over the entire sun. Evidence is presented for two proposed hypotheses, namely: (1) a twist in the flux tubes of new AFSs is a key factor in determining which new AFSs will grow; and (2) this twist is related to the well-known asymmetry of sunspot groups.

Weart, S.↗
NASA NTRS1973

Solution of quadratic matrix equations for free vibration analysis of structures.

An efficient digital computer procedure and the related numerical algorithm are presented herein for the solution of quadratic matrix equations associated with free vibration analysis of structures. Such a procedure enables accurate and economical analysis of natural frequencies and associated modes of discretized structures. The numerically stable algorithm is based on the Sturm sequence method, which fully exploits the banded form of associated stiffness and mass matrices. The related computer program written in FORTRAN V for the JPL UNIVAC 1108 computer proves to be substantially more accurate and economical than other existing procedures of such analysis. Numerical examples are presented for two structures - a cantilever beam and a semicircular arch.

Gupta, K. K.↗
NASA NTRS1973

State space approach to mixed boundary value problems.

A state-space procedure for the formulation and solution of mixed boundary value problems is established. This procedure is a natural extension of the method used in initial value problems; however, certain special theorems and rules must be developed. The scope of the applications of the approach includes beam, arch, and axisymmetric shell problems in structural analysis, boundary layer problems in fluid mechanics, and eigenvalue problems for deformable bodies. Many classical methods in these fields developed by Holzer, Prohl, Myklestad, Thomson, Love-Meissner, and others can be either simplified or unified under new light shed by the state-variable approach. A beam problem is included as an illustration.

Chen, C. F.↗
NASA NTRS1971

A Stability Analysis of Cylindrical Panels Using a Finite Element Formulation

A cylindrical finite element suitable for the linear stability analysis of cylindrical shells is developed. Energy principles and variational methods lead to a problem formulation which lends itself to physical interpretations of the governing matrices of the finite element. By properly grouping the terms which result from taking the second variation of the potential energy of the element, it is possible to identify three distinct types of matrices. The first matrix is the conventional stiffness matrix; the second is an initial stress stiffness matrix; and the third is an initial displacement stiffness matrix. With the assumption of linearity, the buckling problem is stated in terms of the classical linear real eigenvalue equation. This problem formulation was programmed on the CDC 6600 series computer. The computer program is used to analyze the buckling of a variety of structures. Columns, arches, flat plates and curved panels with and without cutouts are considered.

Snyder, R. E.↗
NASA NTRS1974

Decameter type IV bursts associated with coronal transients

The characteristics of four moving type IV burst observed with a 65- to 20-MHz swept-frequency interferometer are discussed. All four bursts were associated with depletions in the electron content of the white light corona. Characteristics of the bursts are not unique i.e., they differ in source size, structure, duration, and their association with other radio bursts. Following Smerd and Dulk (1971), it is assumed that a shock wave, moving out from the flare site is responsible for the expansion of a magnetic arch or the ejection of a plasmoid which is observed as the usual type IV burst. Behind the shock wave, the compressed coronal gas moves outward, and as it expands it causes a depletion of electrons in the inner corona. After the passage of the shock wave, sometimes the coronal magnetic field structure is restored to its initial situation, as evidenced by the observation of homologous transients.

Gergely, T. E.↗
NASA NTRS1974

Magnetic field and electric current structure in the chromosphere

The three-dimensional vector magnetic field structure in the chromosphere above an active region is deduced by using high-resolution H-alpha filtergrams together with a simultaneous digital magnetogram. An analog model of the field is made with 400 metal wires representing field lines that outline the H-alpha structure. The height extent of the field is determined from vertical field-gradient observations around sunspots, from observed fibril heights, and from an assumption that the sources of the field are largely local. The computed electric currents (typically 10 mA/sq m) are found to flow in patterns not similar to observed features and not parallel to magnetic fields. Force structures correspond to observed solar features; the dynamics to be expected include: downward motion in bipolar areas in the lower chromosphere, an outflow of the outer chromosphere into the corona with radially outward flow above bipolar plage regions, and motion of arch filament systems.

Dravins, D.↗