Search NASA⌕ Search

SEARCH · Search NASA

Results for “brittle materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Deformation and Fracture Behavior of Additively Manufactured 316L Stainless Steel

Tensile deformation and fracture behavior of an additively manufactured (AM) 316L stainless steel (SS) in the as-built, stress-relieved, and solution-annealed conditions was investigated using in situ tensile testing in a scanning electron microscope with an electron back scattering diffraction (SEM–EBSD) detector. Analyses were performed to discuss the characteristic deformation and fracture process of the fine-grained AM 316L SS with and without relaxation heat treatment. The as-built 316L showed the highest strength, and both post-build heat treatments lowered the strength of the alloy. Regardless of the post-build processing, the AM 316L SS showed overall higher strength but slightly lower ductility when compared to the wrought (WT) 316L SS. Analysis of EBSD data indicated that the characteristic microstructural features from AM, such as the complex and fine grain morphology, dislocation network, pores, and silicon-rich oxides, evolved and exerted various roles during the tensile deformation and fracture processes. Further, it was obvious that the interaction of dislocation slips with oxide particles and cavities (or pores) resulted in an accelerated cracking in AM 316L SS. Overall, however, their influence on mechanical behavior was limited, as the genuinely high ductility of 316L SS could help avoid any premature or brittle fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impact of annealing at 1000°C in flowing He with low O 2 concentration on the room temperature tensile properties of Mo alloys

NorthStar is developing an accelerator-based technology to produce the medical isotope Mo-99. A previous ORNL report (ORNL/SPR-2022/2490) studied the oxidation behavior of Mo in flowing He with low oxygen content at 800°C and 1000°C and it was shown that an O 2 concentration lower than ~5ppm (μ1/1) is required to achieve acceptable oxidation rates for wrought or powder metallurgy (PM) Mo. Oxidation may also impact the mechanical properties of Mo and this report summarizes tensile results at room temperature on wrought and PM Mo before and after exposure at 1000°C in flowing He with O 2 concentration varying from 1 to 15 ppm O 2 . It was found that oxidation at 1000°C results in a significant decrease of Mo strength and ductility with brittle intergranular fracture surfaces, likely due to the segregation of oxygen at grain boundaries. For the PM Mo material, the decrease in strength and ductility was also observed after annealing in vacuum at 1000°C, indicating that the diffusion of the oxygen trapped in the material pores to grain boundaries after 20-100h at 1000°C is sufficient to embrittle the material. Finally, initial results on actual aMo and high-density disks provided by NorthStar revealed the lack of ductility of the materials due to the specific disk microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Compression Analysis of Materials via in situ X-ray Computed Tomography

X-ray computed tomography (X-ray CT) is an analytical technique used in materials science to non– destructively characterize features in a variety of materials like polymers, metals, composites, and explosives. The non-destructive imaging allows for the analysis of features (voids and cracks), which give a fundamental understanding of material characteristics.This is more effective when combinedwith a load cell to expose the material to realworld stimuli to understand material characteristics and morphological behavior in situ. This study focused on using in situ X-ray CT to understand the material characteristics and morphological changes of sugar prills and a lattice under a compressive load. Sugar prills are used as a surrogate to analyze explosives in a safer and less expensiveway. The sugar prills were found to be brittle and shattered when compressed via the CT renderings and the stress/strain information. The lattices are used as both the basis and ground truth comparison for the development of models to predict the morphological and material characteristic changes that occur as a result of loading. The lattice was found to have weak regions due to low polymer interlayer fusion in these regions during the printing process. It was also found that under the initial compression the lattice demonstrated elastic behavior as its cellular structure was intact until the cellular structure started to collapse causing yielding in the lattice. Additionally, the analysis of the sugar prills and lattice demonstrate the information that can be gleaned from in situ X-ray CT experiments that would be lost in traditional pre- and post-mortem X-rayCT analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The role of specimen size and grain boundary characteristics in the yield strength of tungsten in microtensile tests

To effectively use the measured properties from small-scale tensile tests for bulk material performance predictions, it is essential to understand the threshold of specimen size-effect strengthening and the interaction between dislocations and microstructures within miniaturized specimens. This study uses pure tungsten to investigate the size effect in terms of specimen size, grain size, and grain boundary characteristics relative to the yield strength of tungsten at room temperature. We evaluate the transition from miniaturized specimen properties to bulk properties and the deformation behavior through small-scale tensile tests of three specimen sizes (large: 80 × 100 × 233 µm³; medium: 7 × 7 × 18 µm³; and small: 2 × 2 × 5 µm³). The testing results reveal that the small and medium specimens exhibit high yield strength with ductile behavior, while the large specimens exhibit brittle failure, consistent with the room temperature strength of tungsten, indicating bulk behavior. We further explore the specimen size-effect sensitivity to yield stress and the scaling relationship between yield strength and the number of grains involved in the deformation. A power-law relationship with the exponent value of approximately -0.5 was found in the yield strength–grain number scaling, implying the Hall-Petch like behavior. A minimum of 7–17 effective grain boundaries across the tensile gauge dimension is required to accurately measure bulk properties.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Determining failure properties of as-received and hydrided unirradiated Zircaloy-4 from ring compression tests

An integrated experimental and computational approach was developed to determine the plastic strain at fracture and to investigate the fracture energy of as-received and hydrided unirradiated Zircaloy-4 nuclear cladding tubes in the hoop direction at room temperature from ring compression testing (RCT). This work builds on previous methods in the literature that were developed to obtain the mechanical properties of nuclear cladding before fracture (Young’s modulus, yield stress, and strain-hardening parameters) from experimental RCT results and extends the characterization of this material class to include material failure properties. Furthermore, a ductile damage approach was developed and implemented in a validated finite element model to predict material failure, evaluate fracture energy, and quantify the plastic strain at fracture initiation. The hydrogen content of the Zircaloy-4 specimens was varied up to 610 wppm when the failure became brittle. As expected, increasing hydrogen content caused embrittlement of the Zircaloy-4 samples tested and the plastic strain at fracture and fracture energy to decrease.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamic Tensile Response of a Fe–49Co–2V Alloy at Various Strain Rates and Temperatures

Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s -1 and temperatures from - 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of δ zirconium hydride morphology in a single crystal using quantitative phase field simulations supported by experiments

In light water nuclear reactors, waterside corrosion of the cladding material leads to the production of hydrogen, a fraction of which is picked up by the zirconium cladding and precipitates into brittle hydride particles. These nanoscale hydride particles aggregate into mesoscale hydride clusters. The principal stacking direction of the nanoscale hydrides precipitated in the cladding tube changes from circumferential in the absence of applied stress to radial under circumferential applied stress. A quantitative phase field model has been developed to predict the hydride morphology observed experimentally and identify the mechanisms responsible for nanoscale hydride stacking. The model focuses on nanoscale hydride precipitation in a single zirconium grain with a detailed description of the anisotropic elastic contribution. The model predictions concerning the shape, orientation, and stacking behavior of nanoscale hydride are analyzed and compared with experimental observations. The model accurately accounts for the experimentally observed elongated nanoscale hydride shape and the stacking of hydrides along the basal plane of the hexagonal zirconium matrix. When investigating the role of applied stress in hydride morphology, the model challenges some of the mechanisms previously proposed to explain hydride reorientation. Finally, although hydride reorientation has been hypothesized to be caused by a change in nanoscale hydride shape, the current study shows that these mechanisms are unlikely to occur.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Functionally graded coatings and claddings

A shear assisted extrusion process for producing cladded materials wherein a cladding material and a material to be cladded are placed in sequence with the cladded material positioned to contact a rotating scroll face first and the material to be cladded second. The two materials are fed through a shear assisted extrusion device at a preselected feed rate and impacted by a rotating scroll face to generate a cladded extrusion product. This process allows for increased through wall strength and decreases the brittleness in formed structures as compared to the prior art.

36 MATERIALS SCIENCE↗
DOE OSTI2025

In situ self-ion (Fe + ) irradiation of ODS-FeCrAl alloy fuel cladding materials with different Cr contents: The early stages of Cr-rich α’ phase precipitation

Oxide-dispersion-strengthened FeCrAl (ODS-FeCrAl) alloys are candidate accident-tolerant fuel cladding materials for light water reactors because they demonstrate satisfactory resistance to materials degradation effects such as high-temperature oxidation, radiation-induced swelling, and creep. Their perspective deployment to market is challenged, however, by their inherent susceptibility to irradiation embrittlement caused by the precipitation of the brittle Cr-rich α’ phase at relatively low temperatures (≤475 °C). This work used in situ self-ion irradiation (150 keV Fe + ) in a transmission electron microscope to elucidate the early stages of Cr-rich α’ phase precipitation in three candidate ODS-FeCrAl alloy fuel cladding materials with different Cr contents (10, 12, and 20 wt.%) and microstructures. The early stages of the process resulting in the precipitation of the Cr-rich α’ phase in these three ODS-FeCrAl alloys under Fe + irradiation were investigated at room temperature and 300 °C up to total fluences of 1.7 × 10 15 ions·cm -2 (2 dpa) and 3.4 × 10 15 ions·cm -2 (4 dpa), using three damage dose rates (5 × 10 –5 , 3.3 × 10 –4 , and 2 × 10 –3 dpa·s -1 ). Post-irradiation examination via scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy and electron energy loss spectroscopy suggested that the precipitation of the Cr-rich α’ phase might be promoted by the phase separation of the alloy matrix into Cr-rich and Fe-rich regions. Interestingly, oxygen impurities segregated preferentially in the Cr-rich regions, possibly promoting the radiation-assisted formation of the Cr-rich α’ phase. α’ phase precipitation was more pronounced at room temperature when compared to 300 °C, and it was clearly promoted by the progressive increase in the Cr content of the ODS-FeCrAl alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermal-Fluid and Thermal-Structural Response of the T-Tube Modular Divertor to Spatiotemporally Varying Heat Loads

Tungsten (W) is the leading candidate for divertor target plates because of its high melting point (>3000°C), thermal conductivity, and ultimate tensile stress. While W and its alloys are the only solid materials that can survive the high heat fluxes incident on the divertor, W’s low-ductility high ductile-to-brittle transition temperature of ~600°C and relatively low recrystallization temperature (RT) of ~1300°C pose structural (among other) challenges. The objective of this work is to estimate the thermal-fluid and thermal-structural performance of the helium (He)-cooled T-tube divertor, which was originally developed by the Advanced Reactor Innovation and Evaluation Study (ARIES) using numerical simulations. Here, predictions of temperature distributions across the plasma-facing structural component and surface pressures from computational fluid dynamics simulations are used to determine stress distributions using commercial structural finite element modeling software over a range of fusion-relevant conditions. The maximum allowable incident heat fluxes are determined based on the temperature limits imposed by the ITER elastic Structural Design Criteria for In-vessel Components (SDC-IC) and the maximum RT over a range of He mass flow rates and presented in the form of performance design charts. Our recent work found that thermal- structural criteria accounting for the low ductility of W in a finger-type modular divertor constrain the maximum incident heat fluxes to values well below the ITER specifications, and those based on considering only the RT demonstrate that integrated thermal-fluid and elastic structural performance evaluation are required for accurate assessment of divertor performance. This novel analysis of the T-tube considers how nonuniform and transient incident heat fluxes affect its thermal-fluid and thermal-structural performance, as well as the effect of volumetric heating, which can be as great as 27% of the power incident on the divertor surface. The W tile of the T-tube, with its relatively large plasma-facing area of ~15 cm 2 , will likely experience significant spatial variations in incident heat flux. This work therefore assesses whether steady-state incident heat flux profiles with a peak of 10 MW/m 2 and maximum heat flux gradients of 200 MW/m 2 per m exceed the structural limits imposed by the ITER elastic SDC-IC and the maximum RT over a range of fusion-relevant conditions. The effect of transient heat fluxes typical of plasma detachment and reattachment from the target plate due, for example, to gas injection are also evaluated

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Enabling Multi-Material Structures of Co-Based Superalloy Using Laser Directed Energy Deposition Additive Manufacturing

Cobalt superalloys such as Tribaloys are widely used in environments that involve high temperatures, corrosion, and wear degradation. Additive manufacturing (AM) processes have been investigated for fabricating Co-based alloys due to design flexibility and efficient materials usage. AM processes are suitable for reducing the manufacturing steps and subsequently reducing manufacturing costs by incorporating multi-materials. Laser directed energy deposition (laser DED) is a suitable AM process for fabricating Co-based alloys. T800 is one of the commercially available Tribaloys that is strengthened through Laves phases and of interest to diverse engineering fields. However, the high content of the Laves phase makes the alloy prone to brittle fracture. In this study, a Ni-20%Cr alloy was used to improve the fabricability of the T800 alloy via laser DED. Different mixture compositions (20%, 30%, 40% NiCr by weight) were investigated. The multi-material T800 + NiCr alloys were heat treated at two different temperatures. These alloy chemistries were characterized for their microstructural, phase, and mechanical properties in the as-fabricated and heat-treated conditions. SEM and XRD characterization indicated the stabilization of ductile phases and homogenization of the Laves phases after laser DED fabrication and heat treatment. In conclusion, the NiCr addition improved the fabricability and structural integrity of the T800 alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Brittle failure analysis and modeling of high-burnup PWR fuel cladding alloys

The aim of this research is the development of methods for predicting mechanical behavior and identification of limiting conditions to prevent brittle failure of high-burnup (HBU) pressure water reactor (PWR) fuel cladding alloys. A finite element (FE) model of the ring compression test (RCT) was created to analyze the failure behavior of zirconium-based alloys with radial hydrides during the RCT. An elastic-plastic material model describes the zirconium alloy. The stress-strain curve needed for the elastic-plastic material model was derived by inverse finite element analyses. Cohesive zone modeling is used to reproduce sudden load drops during RCT loading. Based on the failure mechanism in non-irradiated ZIRLO (R) claddings, a micro-mechanical model was developed that distinguishes between brittle failure along hydrides and ductile failure of the zirconium matrix. Two different cohesive laws representing these types of failure are present in the same cohesive interface. The key differences between these constitutive laws are the cohesive strength, the stress at which damage initiates, and the cohesive energy, which is the damage energy dissipated by the cohesive zone. Statistically generated matrix-hydride distributions were mapped onto the cohesive elements and simulations with focus on the first load drop were performed. Computational results are in good agreement with the RCT results conducted on high-burnup M5 (R) samples. It could be shown that crack initiation and propagation strongly depend on the specific configuration of hydrides and matrix material in the fracture area.

Simbruner, Kai↗
DOE OSTI2025

Polylactic acid (PLA)-based multifunctional and biodegradable nanocomposites and their applications

Polylactic acid (PLA)-based nanocomposites are emerging as multifunctional, biodegradable materials, offering sustainable alternatives to petroleum-based plastics. This review examines recent advancements in PLA nanocomposites, focusing on enhanced mechanical strength, thermal stability, and biodegradability achieved through nanofillers like metallic particles, carbon-based materials, and ceramics. Techniques such as in situ polymerization, melt mixing, and electrospinning enable application-specific improvements. PLA's limitations, including brittleness and low barrier properties, are addressed to support diverse applications: in packaging (e.g., extended shelf life), biomedicine (e.g., degradable implants), and electronics (e.g., flexible devices). Despite challenges with filler dispersion and thermal resistance, continued innovations expand PLA's potential across multiple industries, contributing to a sustainable, circular economy.

Biodegradable polymers↗
DOE OSTI2022

Metamorphism-facilitated faulting in deforming orthopyroxene: Implications for global intermediate-depth seismicity

Significance The exothermic metamorphic reaction in orthopyroxene (Opx), a major component of oceanic lithospheric mantle, is shown to trigger brittle failure in laboratory deformation experiments under conditions where garnet exsolution takes place. The reaction product is an extremely fine-grained material, forming narrow reaction zones that are mechanically weak, thereby facilitating macroscopic faulting. Oceanic subduction zones are characterized by two separate bands of seismicity, known as the double seismic zone. The upper band of seismicity, located in the oceanic crust, is well explained by dehydration-induced mechanical instability. Our newly discovered metamorphism-induced mechanical instability provides an alternative physical mechanism for earthquakes in the lower band of seismicity (located in the oceanic lithospheric mantle), with no requirement of hydration/dehydration processes.

58 GEOSCIENCES↗
DOE OSTI2025

Blending Compostable Plastics for Packaging Applications

Non-sustainable packaging materials (polymers) are a large portion of the increasing amount of plastic waste that become environmental pollutants. While many biodegradable or compostable polymers have been developed in recent years, most fail to compete with the non-sustainable polymers dominating the market, due to lack of certain desired properties, such as thermal (high melt temperature) and mechanical (high ductility) performance. For example, the popular compostable polymer polylactic acid (PLLA) has a high melt temperature but is very brittle. Another polymer, poly(d-valerolactone) (PVL) demonstrates great ductility but has a very low melt temperature. By blending PLLA and PVL, there is an opportunity to create a new biodegradable material with synergistic desired properties for packaging applications. In this study, we produce several (9) physical blends of PVL and PLLA with varying compositions of the two polymers while applying three different materials to make them more compatible (compatibilizers). We test the success of compatibilization by scanning electron microscopy (SEM), mechanic testing (strain at break) and differential scanning calorimetry (melting temperature). Overall, we highlight several promising materials with high compatibility and desired thermomechanical properties for sustainable packaging. Ideally, these materials could help mitigate future plastic pollution in Colorado and beyond.

blending↗
DOE OSTI2023

Bending and shear improvements in 3D-printed core sandwich composites through modification of resin uptake in the skin/core interphase region

Fused deposition modeling (FDM) printed polymers are rarely used as a structural material due to anisotropic and low mechanical properties compared with conventional composites. In recent years, greater need has been expressed for recycling of materials, such as recyclable FDM, at the end of service life to reduce environmental pollution and manufacture cost. However, how the amount of resin uptake in the skin and skin/core interphase affects the bending and shear performance of the sandwich composites when replacing the low strength and ductile core (conventional core) with a high strength and brittle core (FDM printed PLA (polylactic acid) core) still remains unclear. A new manufacturing routine is needed to improve the incorporation of FDM printed polymers in composite structures. In this work, FDM printed PLA was used as core material and sandwiched between two unidirectional glass fiber reinforced polymer (GFRP) skins to form a sandwich composite by compression-molding (CM) process, which provides a good manufacturing strategy for skin/core interphase modification. The significance of the CM process is proved by investigating the effect of resin uptake on bending and in-plane/out-of-plane shear performances. Current first order shear deformation (FSDT) theory lacks a direct connection between the in-plane shear stress and out-of-shear stress in the core region of sandwich composites. With the help of DIC, a connection between the in-plane shear and the out-of-plane shear strain was built and in-plane shear properties can acquire through out-of-plane shear properties, hence reducing the redundancy of sample preparation or the need for simulation. A significant improvement was found compared with the optimized resin uptake (Optimized resin uptake range: 20.43%–22.86 wt%) 3D-printed PLA core sandwich composite and lowest performance sandwich composite (Improvement: in-plane shear strength (~34%)/modulus (~29%), out-of-plane shear strength (~25%)/modulus (~31%), specific peak bending load (~19%)). Finally, compared with balsa core sandwich composites, the 3D-printed cores are suitable for use in composite sandwich structures in many applications with a satisfactory strength-to-weight ratio.

3D-printed core sandwich composite↗
DOE OSTI2026

High temperature stabilization of ultrafine grain tungsten alloys through synergistic compositional complexities

Thermally-stabilized fine-grained microstructures in tungsten provide a pathway to harnessing enhanced properties such as a reduced ductile-to-brittle transition temperature and improved strength while mitigating the adverse effects of grain growth and recrystallization. Here, in this study, we employ a material design strategy that relies on grain boundary segregation in the nanocrystalline state driven by alloy thermodynamics balanced with impurity scavenging through in situ formation of kinetically-stabilizing metal carbides. A W-Ti-Cr alloy is designed through lattice Monte Carlo methods and subsequently synthesized in a single-phase nanocrystalline state, which upon annealing, evolves into an ultrafine grained microstructure containing chromium grain boundary segregation collectively with a dispersed TiX (X=C,O) phase through the reaction of titanium with carbon and oxygen impurities. In situ synchrotron X-ray diffraction experiments demonstrate that increased Ti promotes stabilization across a larger temperature range but with diminishing returns above 10 at.% Ti. Long-term stability was confirmed through the retention of the ultrafine grained microstructure for a total of 8 days (192 h) at 1300 °C without grain/carbide growth and/or recrystallization. Our results demonstrate that, through strategic tailoring of composition and microstructure, one can harness the benefits of both thermodynamic and kinetic stabilization mechanisms, opening pathways for future alloy formulations that expand the window of stability.

36 MATERIALS SCIENCE↗