Search NASA⌕ Search

SEARCH · Search NASA

Results for “bulk data transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Experimental Study of Fuel Heating at Low Temperatures in a Wing Tank Model, Volume 1

Scale model fuel heating systems for use with aviation hydrocarbon fuel at low temperatures were investigated. The effectiveness of the heating systems in providing flowability and pumpability at extreme low temperature when some freezing of the fuel would otherwise occur is evaluated. The test tank simulated a section of an outer wing tank, and was chilled on the upper and lower surfaces. Turbine engine lubricating oil was heated, and recirculating fuel transferred the heat. Fuels included: a commercial Jet A; an intermediate freeze point distillate; a higher freeze point distillate blended according to Experimental Referee Broadened Specification guidelines; and a higher freeze point paraffinic distillate used in a preceding investigation. Each fuel was chilled to selected temperature to evaluate unpumpable solid formation (holdup). Tests simulating extreme cold weather flight, without heating, provided baseline fuel holdup data. Heating and recirculating fuel increased bulk temperature significantly; it had a relatively small effect on temperature near the bottom of the tank. Methods which increased penetration of heated fuel into the lower boundary layer improved the capability for reducing holdup.

Stockemer, F. J.↗

Formation of nanocavities in dielectrics: A self-consistent modeling

Tight focusing of a subpicosecond laser pulse in transparent dielectrics is an efficient way to release laser energy and to produce plasma. A micro-explosion results in a submicrometer cavity formation if the deposited laser energy exceeds a threshold. A self-consistent model is developed that describes this process. The energy deposition is described by a full set of Maxwell's equations in the three-dimensional geometry and it accounts for nonlinear propagation phenomena in the femtosecond time scale. The calculated energy deposition is transferred to a hydrodynamic code that describes the cavity formation. Numerical simulations show that cavity size in silica depends strongly on the latent heat of sublimation. An equation of state is developed and introduced into the hydrodynamic model that takes into account the influence of such material parameters as the binding energy, the bulk modulus, and the Grueneisen coefficient. The cavity and shock-affected region sizes are compared to experimental data. This comparison suggests that laser micro-explosions might allow to tune the parameters of equations of state in the domain of phase transitions in a cold dense matter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effects of Heating Configuration and Operating Parameters on Heat Transfer and Interfacial Physics of Microgravity Flow Boiling With Subcooled Inlet Conditions –Experiments Onboard the International Space Station

This study is part of the Flow Boiling and Condensation Experiment (FBCE), a collaborative effort between the Purdue University Boiling and Two-Phase Flow Laboratory (PU-BTPFL) and the NASA Glenn Research Center. The FBCE fitted with the Flow Boiling Module (FBM) was launched to the International Space Station (ISS) in August 2021 and experiments were successfully performed from February to July 2022 to amass a large microgravity-flow-boiling database. This study is focused on heat transfer and flow visualization of microgravity flow boiling of n-Perfluorohexane in a rectangular channel of 5.0 mm height, 2.5 mm width (heated), and 114.6 mm length, with subcooled inlet conditions. High-speed-video photography is utilized to present flow patterns and temporal interfacial behavior. Heat transfer results are presented in the form of flow boiling curves and both parametric curves and streamwise profiles of wall temperature and heat transfer coefficient. Firstly, the parametric effects of mass velocity (199.4 – 3200.0 kg/m 2 s), inlet subcooling (0.2 – 46.0°C), and inlet pressure (124.2 – 176.7 kPa), on the aforementioned aspects are assessed for double-sided heating to establish them for a microgravity environment. Of these three parameters, mass velocity and inlet subcooling mostly determine the microgravity flow boiling behavior, while inlet pressure plays an insignificant role. Flow patterns for double-sided heating are more complex than those for single-sided heating due to interaction between the two vapor layers. Vapor interaction is minimized at high subcoolings and high mass velocities due to strong condensation offered by the subcooled bulk liquid layer separating them. Despite the different flow patterns, both single- and double-sided heating generally result in similar parametric trends and local heat transfer coefficients for similar operating conditions. Flow instabilities manifest as temporal flow anomalies and temperature oscillations, and their severity increases with increasing boiling number. Secondly, the effects of heating configuration are analyzed by comparing and contrasting several aspects of single- and double-sided heating data. The heat fluxes at which onset of nucleate boiling degradation (ONBD) and critical heat flux (CHF) occur are distinctly different for single- and double-sided heating. There exists a threshold inlet subcooling demarcating the dominance of flow acceleration and condensation effects in vapor removal from the near-wall region and replenishment of fresh liquid for boiling. Above the threshold, condensation from the near-wall region is dominant and single-sided heating yields higher heat fluxes, and below it, acceleration is dominant and double-sided yields higher heat fluxes. At mass velocity in the range of 200 – 2400 kg/m 2 s, the threshold inlet subcooling lies in the approximate range of 20 – 30°C (corresponding inlet quality of roughly -0.40 – -0.20).

Microgravity↗

Raman spectroscopy of isotopically pure ({sup 12}C, {sup 13}C) and isotopically mixed ({sup 12.5}C) diamond single crystals at ultrahigh pressures

The Raman scattering by isotopically pure {sup 12}C and {sup 13}C diamond single crystals and by isotopically mixed {sup 12.5}C diamond single crystals is studied at a high accuracy. The studies are performed over a wide pressure range up to 73 GPa using helium as a hydrostatic pressure-transferring medium. It is found that the quantum effects, which determine the difference between the ratio of the Raman scattering frequencies in the {sup 12}C and {sup 13}C diamonds and the classical ratio (1.0408), increase to 30 GPa and then decrease. Thus, inversion in the sign of the quantum contribution to the physical properties of diamond during compression is detected. Our data suggest that the maximum possible difference between the bulk moduli of the {sup 12}C and {sup 13}C diamonds is 0.15%. The investigation of the isotopically mixed {sup 12.5}C diamond shows that the effective mass, which determines the Raman frequency, decreases during compression from 12.38 au at normal pressure to 12.33 au at 73 GPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Direct measurement and calculation of rubber bulk modulus by piston-cylinder method using conventional mechanical testing equipment

This article describes a method to directly measure the bulk modulus of rubber using a piston-cylinder type apparatus. The function of the testing apparatus is to reliably transfer load to the water inside the vessel and allow for the accurate and continuous measurement of volumetric displacement as the contents are compressed. During the test, load is applied to a piston-cylinder containing the rubber test sample and water using a conventional mechanical testing load frame. Load and the travel of the piston are recorded by a load cell and extensometer, respectfully. A brass or stainless steel plug of the same dimensions as the test sample is tested as a control sample to isolate the compliance of the system, including the compressibility of water and compliance of the piston-cylinder. The results from this control test are used to disincorporate the compliance of the system from the sample test results. Load-linear displacement data are mathematically converted to pressure-volumetric displacement data, from which bulk modulus is calculated. The test apparatus and method are validated using the known bulk modulus of water. Finally, the bulk modulus for two similar rubbers is evaluated. The validity of the results and limitations of the device are discussed.

36 MATERIALS SCIENCE↗

Theoretical study of vibrational energy transfer of free OH groups at the water-air interface

Recent experimental studies have shown that the vibrational dynamics of free OH groups at the water-air interface is significantly different from that in bulk water. In this work, by performing molecular dynamics simulations and mixed quantum/classical calculations, we investigate different vibrational energy transfer pathways of free OH groups at the water-air interface. The calculated intramolecular vibrational energy transfer rate constant and the free OH bond reorientation time scale agree well with the experiment. It is also found that, due to the small intermolecular vibrational couplings, the intermolecular vibrational energy transfer pathway that is very important in bulk water plays a much less significant role in the vibrational energy relaxation of the free OH groups at the water-air interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Far Infrared Lines of OH as Molecular Cloud Diagnostics

Future IR missions should give some priority to high resolution spectroscopic observations of the set of far-IR transitions of OH. There are 15 far-IR lines arising between the lowest eight rotational levels of OH, and ISO detected nine of them. Furthermore, ISO found the OH lines, sometimes in emission and sometimes in absorption, in a wide variety of galactic and extragalactic objects ranging from AGB stars to molecular clouds to active galactic nuclei and ultra-luminous IR galaxies. The ISO/LWS Fabry-Perot resolved the 119 m doublet line in a few of the strong sources. This set of OH lines provides a uniquely important diagnostic for many reasons: the lines span a wide wavelength range (28.9 m to 163.2 m); the transitions have fast radiative rates; the abundance of the species is relatively high; the IR continuum plays an important role as a pump; the contribution from shocks is relatively minor; and, not least, the powerful centimeter-wave radiation from OH allows comparison with radio and VLBI datasets. The problem is that the large number of sensitive free parameters, and the large optical depths of the strongest lines, make modeling the full set a difficult job. The SWAS montecarlo radiative transfer code has been used to analyze the ISO/LWS spectra of a number of objects with good success, including in both the lines and the FIR continuum; the DUSTY radiative transfer code was used to insure a self-consistent continuum. Other far IR lines including those from H2O, CO, and [OI] are also in the code. The OH lines all show features which future FIR spectrometers should be able to resolve, and which will enable further refinements in the details of each cloud's structure. Some examples are given, including the case of S140, for which independent SWAS data found evidence for bulk flows.

Smith, Howard A.↗

Marangoni Effects on Near-Bubble Microscale Transport During Boiling of Binary Fluid Mixtures

In earlier investigations, Marangoni effects were observed to be the dominant mechanism of boiling transport in 2-propanol/water mixtures under reduced gravity conditions. In this investigation we have examined the mechanisms of binary mixture boiling by exploring the transport near a single bubble generated in a binary mixture between a heated surface and cold surface. The temperature field created in the liquid around the bubble produces vaporization over the portion of its interface near the heated surface and condensation over portions of its interface near the cold surface. Experiments were conducted using different mixtures of water and 2-propanol under 1g conditions and under reduced gravity conditions aboard the KC135 aircraft. Since 2-propanol is more volatile than water, there is a lower concentration of 2-propanol near the hot surface and a higher concentration of 2-propanol near the cold plate relative to the bulk quantity. This difference in interface concentration gives rise to strong Marangoni effects that move liquid toward the hot plate in the near bubble region for 2-propanol and water mixtures. In the experiments in this study, the pressure of the test system was maintained at about 5 kPa to achieve the full spectrum of boiling behavior (nucleate boiling, critical heat flux and film boiling) at low temperature and heat flux levels. Heat transfer data and visual documentation of the bubble shape were extracted from the experimental results. In the 1-g experiments at moderate to high heat flux levels, the bubble was observed to grow into a mushroom shape with a larger top portion near the cold plate due to the buoyancy effect. The shape of the bubble was somewhat affected by the cold plate subcooling and the superheat of the heated surface. At low superheat levels for the heated surface, several active nucleation sites were observed, and the vapor stems from them merged to form a larger bubble. The generation rate of vapor is moderate in this regime and the bubble shape is cylindrical in appearance. In some instances, the bubble interface appeared to oscillate. At higher applied heat flux levels, the top of the bubble became larger, apparently to provide more condensing interface area adjacent to the cold plate. Increasing the applied heat flux ultimately led to dry-out of the heated surface, with conditions just prior to dryout corresponding to the maximum heat flux (CHF). A more stable bubble was observed when the system attained the minimum heat flux (for film boiling). In this regime, most of the surface under the bottom of the bubble was dry with nucleate boiling sometimes occuring around the contact perimeter of the bubble at heated surface. Different variations (e.g. gap between two plates, molar concentration of the liquid mixture) of the experiments were examined to determine parametric effects on the boiling process and to determine the best conditions for the KC135 reduced gravity tests. Variation of the gap was found to have a minor impact on the CHF. However, reducing the gap between the hot and cold surface was observed to significantly reduce the minimum heat flux for fixed molar concentration of 2-propanol. In the reduced gravity experiments aboard the KC135 aircraft, the bubble formed in the 6.4 mm gap was generally cylindrical or barrel shaped and it increased its extent laterally as the surface superheat increased. In reduced gravity experiments, dryout of the heated surface under the bubble was observed to occur at a lower superheated temperature than for 1g conditions. Observed features of the boiling process and heat transfer data under reduced gravity will be discussed in detail. The results of the reduced gravity experiments will also be compared to those obtained in comparable 1g experiments. In tandem with the experiments we are also developing a computational model of the transport in the liquid surrounding the bubble during the boiling process. The computational model uses a level set method to model motion of the interface. It will incorporate a macroscale treatment of the transport in the liquid gap between the surfaces and a microscale treatment of transport in the regions between the bubble interface and the solid surfaces. The features of the model will be described in detail. Future research directions suggested by the results to date will also be discussed.

V. Carey↗

Time and Space Resolved Wall Temperature Measurements during Nucleate Boiling with Constant Heat Flux Boundary Conditions

The lack of temporally and spatially resolved measurements under nucleate bubbles has complicated efforts to fully explain pool-boiling phenomena. The objective of this current work is to acquire time and space resolved temperature distributions under nucleate bubbles on a constant heat flux surface. This was performed using a microheater array with 100 micron resolution that allowed effectively simultaneous measurements of surface temperature while supplying a constant dissipative heat flux. This data is then correlated with high speed (> 1000Hz) visual recordings of the bubble growth and departure from the heater surface acquired from below and from the side of the heater. The data indicate that a significant source of energy during bubble nucleation and initial growth is the superheated layer around the bubble. Bubble coalescence was not observed to decrease surface temperature as significantly as bubble departure from the surface. Since bubble departure is typically followed by a sharp increase in the heater surface temperature, it is surmised that the departing bubble effectively removes the superheated layer, allowing a high local heat transfer rate with the bulk fluid through transient conduction/micro-convection during rewetting.

Myers, Jerry G.↗

Hypersonic Second Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

Riverine dissolved organic matter transformations increase with watershed area, water residence time, and Damköhler numbers in nested watersheds

Abstract Quantifying the relative influence of factors and processes controlling riverine ecosystem function is essential to predicting future conditions under global change. Dissolved organic matter (DOM) is a fundamental component of riverine ecosystems that fuels microbial food webs, influences nutrient and light availability, and represents a significant carbon flux globally. The heterogeneous nature of DOM molecular composition and its propensity for interaction (i.e., functional diversity) can characterize riverine ecosystem function across spatiotemporal scales. To investigate fundamental drivers of DOM diversity, we collected seasonal water samples from 42 nested locations within five watersheds spanning multiple watershed sizes (~ 5 to 30,000 km 2 ) across the United States. Patterns in DOM molecular richness, aromaticity, relative abundance of N-containing formulas, and putative biochemical transformations derived from high-resolution mass spectrometry were assessed across gradients of explanatory variables associated with watershed characteristics (e.g., watershed area, water residence time, land cover). We found that putative biochemical transformations were more strongly related to explanatory variables across watersheds than common bulk DOM parameters and that watershed area, surface water residence time and derived Damköhler numbers representing DOM reactivity timescales were strong predictors of DOM diversity. The data also indicate that catchment-specific land cover factors can significantly influence DOM diversity in diverging directions. Overall, the results highlight the importance of considering water residence time and land cover when interpreting longitudinal patterns in DOM chemistry and the continued challenge of identifying generalizable drivers that are transferable across watershed and regional scales for application in Earth system models. This work also introduces a Findable Accessible Interoperable Reusable (FAIR) dataset (> 300 samples) to the community for future syntheses.

54 ENVIRONMENTAL SCIENCES↗

Fragmented molecular complexes: The role of the magnetic field in feeding internal supersonic motions

A hierarchical structure for molecular complexes in their cold phase i.e., preceeding the formation of massive stars, was derived from extensive large scale CO(13)(J=1=0) observations: the mass is found to be distributed into virialized clouds which fill only a very low fraction approx. 01 of the volume of the complex and are supported against gravity by internal supersonic motions. An efficient mechanism was found to transfer kinetic energy from the orbital motions of the clouds to their internal random motions. The large perturbations of the magnetic field induced at the cloud boundaries by their interactions with their neighbors generate systems of hydromagnetic waves trapped inside the clouds. The magnetic field lines being closely coupled to the gas at the densities which prevail in the bulk of the clouds volume, internal velocity dispersion is thus generated. Some conclusions derived from this data are given.

Falgarone, E.↗

An Offload NIC for NASA, NLR, and Grid Computing

This work addresses distributed data management and access dynamically configurable high-speed access to data distributed and shared over wide-area high-speed network environments. An offload engine NIC (network interface card) is proposed that scales at nX10-Gbps increments through 100-Gbps full duplex. The Globus de facto standard was used in projects requiring secure, robust, high-speed bulk data transport. Novel extension mechanisms were derived that will combine these technologies for use by GridFTP, bandwidth management resources, and host CPU (central processing unit) acceleration. The result will be wire-rate encrypted Globus grid data transactions through offload for splintering, encryption, and compression. As the need for greater network bandwidth increases, there is an inherent need for faster CPUs. The best way to accelerate CPUs is through a network acceleration engine. Grid computing data transfers for the Globus tool set did not have wire-rate encryption or compression. Existing technology cannot keep pace with the greater bandwidths of backplane and network connections. Present offload engines with ports to Ethernet are 32 to 40 Gbps f-d at best. The best of ultra-high-speed offload engines use expensive ASICs (application specific integrated circuits) or NPUs (network processing units). The present state of the art also includes bonding and the use of multiple NICs that are also in the planning stages for future portability to ASICs and software to accommodate data rates at 100 Gbps. The remaining industry solutions are for carrier-grade equipment manufacturers, with costly line cards having multiples of 10-Gbps ports, or 100-Gbps ports such as CFP modules that interface to costly ASICs and related circuitry. All of the existing solutions vary in configuration based on requirements of the host, motherboard, or carriergrade equipment. The purpose of the innovation is to eliminate data bottlenecks within cluster, grid, and cloud computing systems, and to add several more capabilities while reducing space consumption and cost. Provisions were designed for interoperability with systems used in the NASA HEC (High-End Computing) program. The new acceleration engine consists of state-ofthe- art FPGA (field-programmable gate array) core IP, C, and Verilog code; novel communication protocol; and extensions to the Globus structure. The engine provides the functions of network acceleration, encryption, compression, packet-ordering, and security added to Globus grid or for cloud data transfer. This system is scalable in nX10-Gbps increments through 100-Gbps f-d. It can be interfaced to industry-standard system-side or network-side devices or core IP in increments of 10 GigE, scaling to provide IEEE 40/100 GigE compliance.

Awrach, James↗

Kinetics of Reduction of Low-Grade Nickel Laterite Ore Using Carbon Monoxide

Reduction of a low-grade nickel laterite ore with carbon monoxide to produce Fe-Ni alloy was investigated using a thermo-gravimetric analysis (TGA) method. Non-isothermal reduction tests with a fixed heating rate of 10 °C/min from room temperature to 1200 °C were carried out to determine the different reduction stages and reaction products in each state. Combining measured mass losses with theoretically calculated values together with X-ray diffraction analysis, the products of different reduction stages were identified and a reaction path was established. Isothermal reduction tests with temperatures ranging from 500 °C to 1100 °C were performed to evaluate the temperature dependence of the reduction kinetics. Various kinetic models were fitted to the experimental data to further determine the rate-controlling step in the isothermal tests. Then, two groups of TG experiments were carried out to study the effect of CO flow rate and sample mass on the rate of reaction. The results indicated that the reduction rate increases with the increase of the reduction temperature from 500 °C to 1100 °C. More alloy products are formed and the apparent activation energies increase from 8.6 to 14.7 kJ/mol with the increase of the reduction temperature from 700 °C to 1100 °C. Accordingly, it was proposed that diffusion of CO in the gas bulk and through the pores of the laterite ore sample bed are the rate limiting steps.

36 MATERIALS SCIENCE↗

The precision-processing subsystem for the Earth Resources Technology Satellite.

Description of the precision processor, a subsystem in the image-processing system for the Earth Resources Technology Satellite (ERTS). This processor is a special-purpose image-measurement and printing system, designed to process user-selected bulk images to produce 1:1,000,000-scale film outputs and digital image data, presented in a Universal-Transverse-Mercator (UTM) projection. The system will remove geometric and radiometric errors introduced by the ERTS multispectral sensors and by the bulk-processor electron-beam recorder. The geometric transformations required for each input scene are determined by resection computations based on reseau measurements and image comparisons with a special ground-control base contained within the system; the images are then printed and digitized by electronic image-transfer techniques.

Chapelle, W. E.↗

Ice water path estimation and characterization using passive microwave radiometry

Model computations of top-of-atmospheric microwave brightness temperatures T(B) from layers of precipitation-sized ice of variable bulk density and ice water content (IWC) are presented. It is shown that the 85-GHz T(B) depends essentially on the ice optical thickness. The results demonstrate the potential usefulness of scattering-based channels for characterizing the ice phase and suggest a top-down methodology for retrieval of cloud vertical structure and precipitation estimation from multifrequency passive microwave measurements. Attention is also given to radiative transfer model results based on the multiparameter radar data initialization from the Cooperative Huntsville Meteorological Experiment (COHMEX) in northern Alabama. It is shown that brightness temperature warming effects due to the inclusion of a cloud liquid water profile are especially significant at 85 GHz during later stages of cloud evolution.

Vivekanandan, J.↗