Search NASA⌕ Search

SEARCH · Search NASA

Results for “bundle method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Parrotfish Teeth: Stiff Biominerals Whose Microstructure Makes Them Tough and Abrasion-Resistant To Bite Stony Corals

Parrotfish (Scaridae) feed by biting stony corals. To investigate how their teeth endure the associated contact stresses, we examine the chemical composition, nano- and microscale structure, and the mechanical properties of the steephead parrotfish Chlorurus microrhinos tooth. Its enameloid is a fluorapatite (Ca 5 (PO 4 ) 3 F) biomineral with outstanding mechanical characteristics: the mean elastic modulus is 124 GPa, and the mean hardness near the biting surface is 7.3 GPa, making this one of the stiffest and hardest biominerals measured; the mean indentation yield strength is above 6 GPa, and the mean fracture toughness is ~.5 MPa·m 1/2 , relatively high for a highly mineralized material. This combination of properties results in high abrasion resistance. Fluorapatite X-ray absorption spectroscopy exhibits linear dichroism at the Ca L-edge, an effect that makes peak intensities vary with crystal orientation, under linearly polarized X-ray illumination. This observation enables polarization-dependent imaging contrast mapping of apatite, a method to quantitatively measure and display nanocrystal orientations in large, pristine arrays of nano- and microcrystalline structures. Parrotfish enameloid consists of 100 nm-wide, microns long crystals co-oriented and assembled into bundles interwoven as the warp and the weave in fabric and therefore termed fibers here. These fibers gradually decrease in average diameter from 5 μm at the back to 2 μm at the tip of the tooth. Intriguingly, this size decrease is spatially correlated with an increase in hardness.

36 MATERIALS SCIENCE↗

Modeling active region transient brightenings observed with X-ray telescope as multi-stranded loops

Strong evidence exists that coronal loops as observed in extreme ultraviolet and soft X-rays may not be monolithic isotropic structures, but can often be more accurately modeled as bundles of independent strands. Modeling the observed active region transient brightenings (ARTBs) within this framework allows for the exploration of the energetic ramifications and characteristics of these stratified structures. Here we present a simple method of detecting and modeling ARTBs observed with the Hinode X-Ray Telescope (XRT) as groups of zero-dimensional strands, which allows us to probe parameter space to better understand the spatial and temporal dependence of strand heating in impulsively heated loops. This partially automated method can be used to analyze a large number of observations to gain a statistical insight into the parameters of coronal structures, including the number of heating events required in a given model to fit the observations. In this article, we present the methodology and demonstrate its use in detecting and modeling ARTBs in a sample data set from Hinode/XRT. These initial results show that, in general, multiple heating events are necessary to reproduce observed ARTBs, but the spatial dependence of these heating events cannot yet be established.

79 ASTRONOMY AND ASTROPHYSICS↗

SU-D-9A-06: 3D Localization of Neurovascular Bundles Through MR-TRUS Registration in Prostate Radiotherapy

Purpose: Erectile dysfunction (ED) is the most common complication of prostate-cancer radiotherapy (RT) and the major mechanism is radiation-induced neurovascular bundle (NVB) damage. However, the localization of the NVB remains challenging. This study's purpose is to accurately localize 3D NVB by integrating MR and transrectal ultrasound (TRUS) images through MR-TRUS fusion. Methods: T1 and T2-weighted MR prostate images were acquired using a Philips 1.5T MR scanner and a pelvic phase-array coil. The 3D TRUS images were captured with a clinical scanner and a 7.5 MHz biplane probe. The TRUS probe was attached to a stepper; the B-mode images were captured from the prostate base to apex at a 1-mm step and the Doppler images were acquired in a 5-mm step. The registration method modeled the prostate tissue as an elastic material, and jointly estimated the boundary condition (surface deformation) and the volumetric deformations under elastic constraint. This technique was validated with a clinical study of 7 patients undergoing RT treatment for prostate cancer. The accuracy of our approach was assessed through the locations of landmarks, as well as previous ultrasound Doppler images of patients. Results: MR-TRUS registration was successfully performed for all patients. The mean displacement of the landmarks between the post-registration MR and TRUS images was 1.37±0.42 mm, which demonstrated the precision of the registration based on the biomechanical model; and the NVB volume Dice Overlap Coefficient was 92.1±3.2%, which demonstrated the accuracy of the NVB localization. Conclusion: We have developed a novel approach to improve 3D NVB localization through MR-TRUS fusion for prostate RT, demonstrated its clinical feasibility, and validated its accuracy with ultrasound Doppler data. This technique could be a useful tool as we try to spare the NVB in prostate RT, monitor NBV response to RT, and potentially improve post-RT potency outcomes.

60 APPLIED LIFE SCIENCES↗

Prediction of number of breached rods following a LBLOCA of Candu plants using a BEPU approach

Radioactive doses following design basis accidents (DBA) have been important safety criteria of Candu nuclear power plant and they have been predicted in terms of the number of breached fuel rods. To support the licensing review on this concern, an analysis of LBLOCA has been conducted by using the BEPU method of KINS, KINS-REM. Number of Breached Rods (NBR) following a LBLOCA was predicted at 95 percentile probabilistic upper level in 95 percentile confidence level. Peak Cladding Temperatures (PCT) of the 84 bundles in the core pass 4 were calculated from the 124 MARS code runs in which the uncertainties of 10 major parameters including fuel thermal conductivity and break flow model were implemented. The fuel rod breaching criteria, PCT>1477 K, was used to determine the NBR 95/95. From the calculation, the predicted NBR 95/95 was 1591 rods and the calculated maximum NBR was lower than 2000 rods. Through the further improvements in feedback of the channel power behavior to thermalhydraulic calculation and in channel group modeling, NBR in more reliable level can be expected. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Flow Field and Pressure Measurements in a 61-Pin Wire-Wrapped Bundle

Texas A and M University is conducting isothermal flow tests in a wire-wrapped, 61-pin hexagonal fuel bundle to support the research on advanced nuclear fuel development sponsored by the Department of Energy (DOE). The purpose of these tests is to produce high spatial- and temporal-resolution measurements of the flow and pressure measurements at different locations of the test bundle. The data resulting from these tests will be used to benchmark numerical simulations of the experiments using both industry-standard Reynolds-averaged Navier-Stokes (RANS) based Computation Fluid Dynamics (CFD) methods and a highly resolved Large Eddy Simulation (LES) computer code. This article described the main features of the experimental facility, its capabilities in producing experimental data of pressure drop and velocity fields at different axial locations and within different exterior and interior sub-channels, using advanced flow visualization techniques. Examples of experimental data outputs and typical locations of the measurements that will included in the research scope are also shown in this article. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multi-field inflation with random potentials: field dimension, feature scale and non-Gaussianity

We explore the super-horizon evolution of the two-point and three-point correlation functions of the primordial density perturbation in randomly-generated multi-field potentials. We use the Transport method to evolve perturbations and give full evolutionary histories for observables. Identifying the separate universe assumption as being analogous to a geometrical description of light rays, we give an expression for the width of the bundle, thereby allowing us to monitor evolution towards the adiabatic limit, as well as providing a useful means of understanding the behaviour in f{sub NL}. Finally, viewing our random potential as a toy model of inflation in the string landscape, we build distributions for observables by evolving trajectories for a large number of realisations of the potential and comment on the prospects for testing such models. We find the distributions for observables to be insensitive to the number of fields over the range 2 to 6, but that these distributions are highly sensitive to the scale of features in the potential. Most sensitive to the scale of features is the spectral index, with more than an order of magnitude increase in the dispersion of predictions over the range of feature scales investigated. Least sensitive was the non-Gaussianity parameter f{sub NL}, which was consistently small; we found no examples of realisations whose non-Gaussianity is capable of being observed by any planned experiment.

79 ASTRONOMY AND ASTROPHYSICS↗

Progress Report on Development of Intermediate Fidelity Full Assembly Analysis Methods

While high fidelity modeling capabilities for various physics phenomena are being pursued under advanced modeling and simulation initiatives under the DOE Office of Nuclear Energy, they generally rely on high-performance computation facilities and are too expensive to be used for parameter-space exploration or design analysis. One-dimensional system codes have been used for a long time and have reached a degree of maturity, but limit their validity to specific applications. Thus, an intermediate fidelity (IF) modeling method is being pursued in this work for a fast-running, modest-fidelity, whole-core transient analyses capability. The new approach is essential for design scoping and engineering analyses and could lead to improvements in the design of the new generations of reactors and to the reduction of uncertainties in safety analysis. This report summarizes the initial effort on the development of the intermediate-fidelity full assembly modeling method. The requirements and the desired merits of the IF approach have been defined. A three-dimensional momentum source model has been developed to model the anisotropic flow in the wire-wrapped rod bundle without the need to resolve the geometric details. It has been confirmed that the momentum source model works well if its affecting region is accurately imposed. The validity of the model is further verified by mesh and parameter sensitivity studies. The developed momentum source model, in principle, can be applied to any wire-wrapped bundle geometries and any flow regimes; while the modeling strategy can be applied to other conditions with complex or distorted geometry, such as flow in blocked channels.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

BlueCRAB Domain Overlapping Coupling: Theory & Verification

Coupling low- and high-fidelity codes is a useful way to model complex engineering systems. Thanks to the high-fidelity code, complex phenomena can be resolved in areas of the system where this is required, yet the efficiency of the lower-fidelity code is still retained in modeling the rest of the system. This document details the theory and implementation of coupling two different thermal-hydraulic codes: the system thermal-hydraulics (STH) code System Analysis Module (SAM) and the coarse-mesh computational fluid dynamics (CFD) code Pronghorn. Both applications are included in the Comprehensive Reactor Analysis Bundle (BlueCRAB) code suite and are based on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework. The domain overlapping (DO) coupling approach was adopted, as it offers proven advantages over more conventional domain decomposition methods. In the DO coupling, SAM provides Pronghorn with boundary conditions that depend on the system-level simulation of the entire plant. In return, the overlapping coupled SAM components–termed “surrogate components”–receive friction factors and source terms computed online based on the Pronghorn simulation. The framework is designed to be generic and enable coupling regardless of geometry and the number of inlet/outlet boundaries in the DO coupled domain. The developed method leads to consistent pressure drops, enthalpies, and scalar concentrations when comparing the coupled SAM and Pronghorn simulations. This document presents the DO coupling approach, along with two verification and two demonstration cases. The proposed problems explore different physical aspects relevant to nuclear reactor analysis, including buoyancy-driven flows, complex flow patterns, and multiple inlets and outlets. Periodically, new versions of this “BlueCRAB Domain Overlapping Coupling: Theory & Verification” report will be issued to reflect future developments and verification tests.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

CFD Verification and Validation of Wire-Wrapped Pin Assemblies

TerraPower is participating in a cooperative project among industry, the national lab system, and academia to perform Verification and Validation (V and V) of Computational Fluid Dynamics (CFD) methods for predicting the flow and heat transfer within liquid-metal-cooled nuclear fuel assemblies with wire-wrapped fuel pins. This project, consisting of both experimental and numerical components, uses surrogate fluids and electrically heated fuel pins to substitute for the liquid metal coolant and the nuclear heat source. The experiments include both unheated assemblies to measure the flow velocities with Laser Doppler Velocimetry (LDV) and Particle Image Velocimetry (PIV), as well as heated assemblies to measure the temperatures of the fluid and the simulated fuel pins with thermocouples. Both sets of experiments also measure the pressure at multiple locations in the system. The numerical component of this work involves high-fidelity Large-Eddy Simulation (LES) modeling and industry-standard Reynolds-Averaged Navier-Stokes (RANS) modeling of the experiments. Furthermore, the experiments and simulations will be conducted on two duct geometries: the first is a non-deformed hexagonal duct that has flat internal duct faces that represents a beginning of life geometry. The other is a deformed duct where the internal hexagonal flow area enlarges then decreases along the axial height to represent the changes that occur to the duct geometry from pressure and irradiation effects in the core. This paper describes the methods and results of the industrial, RANS-based CFD code verification, solution verification, and solution validation. The V and V simulations are being performed for the following experiment test geometries: - Isothermal non-deformed bundle; - Heated non-deformed bundle; - Isothermal deformed bundle; - Heated deformed bundle. These flows have been computed at first with the pre-test design specifications, without the aid of any experimental results. Later, post-test calculations will be performed incorporating the actual test conditions and input from some of the experimental results. These RANS simulations of helically wire-wrapped fuel assemblies employ meshes of bare pins without the wire-wrap in the bundle. The effect of wire-wrap on the flow is accounted for by introducing a momentum source into the governing fluid equations. The momentum source is only applied to cells corresponding to the location of the wire-wrap, and its components in each cell are based on the local flow field. This methodology simplifies the geometry and mesh generation and reduces the cell count, while still capturing the effects of the wire-wrap. The momentum source approach is used for all of the assembly simulations performed in this study. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

SOLVING CONJUGATE HEAT TRANSFER PROBLEM IN TWO-PHASE FLOW USING NEWTON-KRYLOV METHOD

In this paper, we successfully demonstrated an application of the Jacobian-free Newton Krylov (JFNK) method in solving the conjugated two-phase channel flow and heat conduction problem, in a fully coupled and fully implicit manner. Such a problem represents the most fundamental piece of safety analysis codes, for example the heat transfer between fuel rods and reactor coolant during postulated accidental scenarios. The two-phase flow is modeled with the widely accepted one-dimensional two-fluid two-phase flow model, and the heat conduction is modeled with two-dimensional heat conduction model. The coupling between these two physics is realized through the wall heat transfer term in fluid equations and heat flux boundary conditions of heat conduction model. For spatial discretization, both the first-order and second- order upwind schemes are considered for flow equations, while the standard central differencing method is used for the heat conduction model. For time integration, both the first-order backward Euler (BDF1) and second-order BDF2 schemes are considered. Several treatments were also introduced to enhance the robustness of the JFNK method in solving such a problem that is discontinuous in nature because of the discrete closure correlations. These treatments include the re-introduction of a transition region between the slug and annular mist flow regimes, and a simplification in the interfacial drag term. Numerical results have been extensively validated with experimental data in both vertical pipe and rod bundle geometries with a wide range of thermal-hydraulics conditions, including pressure, inlet subcooling, wall heat flux, outlet void fraction, and etc. Further benchmark with the RELAP5-3D code confirms the correct implementation of wall heat transfer models.

42 ENGINEERING↗

Constructing a class of solutions for the Hamilton-Jacobi equation in field theory

A new approach leading to the formulation of the Hamilton-Jacobi equation for field theories is investigated within the framework of jet bundles and multisymplectic manifolds. An algorithm associating classes of solutions to given sets of boundary conditions of the field equations is provided. The paper also puts into evidence the intrinsic limits of the Hamilton-Jacobi method as an algorithm to determine families of solutions of the field equations, showing how the choice of the boundary data is often limited by compatibility conditions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

SU-F-J-167: Use of MR for Permanent Prostate Implant Preplanning

Purpose: To study the feasibility using MR imaging to improve target definition on ultrasound during permanent prostate implants and aid in source strength determination for treatment planning in the OR. Methods: Patients who receive permanent prostate implants undergo MR and CT imaging prior to the implant procedure to determine the volume of the prostate, bony restriction to the procedure, bladder extension, external sphincter length and neurovascular bundle. The volume of the prostate is generally used to order seeds for the procedure. In 10 patients, the MR was used as the preplanning study with the PTV defined as a 2 mm expansion of the MR prostate in all directions except the posterior. Various dose volume parameters for the MR prostate and the PTV were compared to the actual preplan developed and executed in the OR. In addition, there parameters were compared to the post implant dosimetry performed 3 weeks after the implant procedure. Results: The results show that the number of seeds used using MR and US (ultrasound) planning was generally with 2 seeds and the maximum difference was 7 seeds. There is no significant difference between any of the dose index parameters of V100, V150, V200, D99 and D90 parameters between MR planning, US planning and postimplant evaluation There was a significant difference between planned D99 (avg of 105%) and achieved D99 (avg 91%). Conclusion: MR imaging is an invaluable tool to improve target definition for permanent prostate implants. Use of MR images for preplanning improves the confidence with which source can be ordered for the procedure that is OR planned. Ordering a maximum of 10 seeds more than planned would be sufficient to deliver a plan in the OR using US. Moving ahead to non-rigid registration between MR ad US images could further increase the confidence level of MR planning.

60 APPLIED LIFE SCIENCES↗

Augmented Monitoring and Condition Assessment Program for SNF Wet Storage Life Extension - 20489

Approximately 27 MTHM of spent nuclear fuel (SNF) owned and managed by the U.S. Department of Energy, Office of Environmental Management is stored in the L Basin at the Savannah River Site (SRS). This 'DOE SNF' is comprised of approximately 12,000 aluminum-clad, aluminum-based fuel assemblies (∼7 MTHM), and approximately 2000 non-aluminum fuel assemblies (∼20 MTHM). A program is in progress to perform Non-Destructive Examination (NDE) of the fuel and their storage containers to characterize the materials' condition, and to evaluate the effects of service to enable continued safe wet storage of the SNF. The Augmented Monitoring and Condition Assessment Program (AMCAP), a two-part program to develop and implement remote underwater Non-Destructive Examination of the aluminum SNF, and of the containers of the non-aluminum SNF, respectively, is aimed at the characterization and evaluation of corrosion degradation of aluminum fuel and container materials. The predominant design of the aluminum SNF (ASNF) stored in L Basin is the Materials Test Reactor (MTR) equivalent design, a plate fuel design. These SNF are stored in 5'' diameter tubes or 5'' x 5'' squares (called bundles) that are nominally 12' or up to 14' long. The SNF is de-bundled and inspected using a custom-designed MTR Fuel Inspection Table. The inspection table provides for indexed fuel positioning for a video camera examination with controlled lighting. A total of 10 of the SNF originating from foreign research and test reactors were selected for examination based on burnup, enrichment, and prior damage caused by service/storage history. A special inspection campaign of these 10 assemblies is in progress. The observed corrosion damage included minor to moderate attack from general corrosion, pitting, crevice, end grain and galvanic corrosion. Example results from the completed inspections are shown and discussed. The focus is a comparison of the as-received condition versus the as-found current storage condition that will serve to validate Water Chemistry and Corrosion Monitoring Programs. The non-aluminum SNF (NASNF) stored in L Basin are of diverse design that includes various geometries with claddings of stainless steel, Zircaloy, and Hastelloy. The fuel core materials include uranium alloys, oxides/mixed oxides, and carbides. These SNF materials, originating from early experimental and test reactors, are in various physical forms including single fuel elements and cut pieces. The fuel is stored in L Basin in various configurations including in direct bundled storage in aluminum tubes and in isolation cans that are in the bundles or in a larger over-size storage container (OSC). Concern with inside-out corrosion and the potential loss of configuration control and ability to handle the storage containers prompted the development of remote NDE methods that include visual and UT technologies to assess the condition of the containers. Candidate stored materials were selected for a special inspection campaign; the development of the NDE methods for the inspection for galvanic, crevice and sediment-induced corrosion (inside-out) are discussed. A summary of the SNF storage in L Basin at the SRS, and an overview of the AMCAP to enable continued safe storage of DOE SNF are described. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Orifice plate for controlling solids flow, methods of use thereof and articles comprising the same

Disclosed herein is an orifice plate comprising one or more plates having orifices disposed therein; the orifices being operative to permit the flow of solids from a moving bed heat exchanger to a solids flow control system; where the orifice plate is downstream of a tube bundle of the moving bed heat exchanger and upstream of the solids flow control system and wherein the orifice plate is operative to evenly distribute the flow of solids in the solids flow control system.

36 MATERIALS SCIENCE↗

High-power compact laser with segmented longitudinal pumping of coupled laser channels

The characteristics of a compact Nd:YAG/Cr:YAG laser with segmented end pumping using a bundle of seven optical fibres are presented. In the regime of optical coupling of thus formed seven laser channels, 3-ns pulses with an energy up to 20 mJ, as well as their trains, are obtained. The used method makes it possible to scale the energy and power of lasers of this type with controlled spatial beam profile. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Clad fiber capacitor and method of making same

A clad capacitor and method of manufacture includes assembling a preform comprising a ductile, electrically conductive fiber; a ductile, electrically insulating cladding positioned on the fiber; and a ductile, electrically conductive sleeve positioned over the cladding. One or more preforms are then bundled, heated and drawn along a longitudinal axis to decrease the diameter of the ductile components of the preform and fuse the preform into a unitized strand.

36 MATERIALS SCIENCE↗

On the holonomy of the Coulomb connection over manifolds with boundary

Narasimhan and Ramadas [Commun. Math. Phys. 67, 121 (1979)] showed that the restricted holonomy group of the Coulomb connection is dense in the connected component of the identity of the gauge group when one considers the product principal bundle S{sup 3}xSU(2){yields}S{sup 3}. Instead of a base manifold S{sup 3}, we consider here a base manifold of dimension n{>=}2 with a boundary and use Dirichlet boundary conditions on connections as defined by Marini [Commun. Pure Appl. Math. 45, 1015 (1992)]. A key step in the method of Narasimhan and Ramadas consisted in showing that the linear space spanned by the curvature form at one specially chosen connection is dense in the holonomy Lie algebra with respect to an appropriate Sobolev norm. Our objective is to explore the effect of the presence of a boundary on this construction of the holonomy Lie algebra. Fixing appropriate Sobolev norms, it will be shown that the space spanned, linearly, by the curvature form at any one connection is never dense in the holonomy Lie algebra. In contrast, the linear space spanned by the curvature form and its first commutators at the flat connection is dense and, in the C{sup {infinity}} category, is in fact the entire holonomy Lie algebra. The former, negative, theorem is proven for a general principle bundle over M, while the latter, positive, theorem is proven only for a product bundle over the closure of a bounded open subset of R{sup n}. Our technique for proving the absence of density consists in showing that the linear space spanned by the curvature form at one point is contained in the kernel of a linear map consisting of a third order differential operator, followed by a restriction operation at the boundary; this mapping is determined by the mean curvature of the boundary.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Breaking Computational Barriers: Real-time Analysis and Optimization with Large-scale Nonlinear Models via Model Reduction

Model reduction for dynamical systems is a promising approach for reducing the computational cost of large-scale physics-based simulations to enable high-fidelity models to be used in many- query (e.g., Bayesian inference) and near-real-time (e.g., fast-turnaround simulation) contexts. While model reduction works well for specialized problems such as linear time-invariant systems, it is much more difficult to obtain accurate, stable, and efficient reduced-order models (ROMs) for systems with general nonlinearities. This report describes several advances that enable nonlinear reduced-order models (ROMs) to be deployed in a variety of time-critical settings. First, we present an error bound for the Gauss-Newton with Approximated Tensors (GNAT) nonlinear model reduction technique. This bound allows the state-space error for the GNAT method to be quantified when applied with the backward Euler time-integration scheme. Second, we present a methodology for preserving classical Lagrangian structure in nonlinear model reduction. This technique guarantees that important properties--such as energy conservation and symplectic time-evolution maps--are preserved when performing model reduction for models described by a Lagrangian formalism (e.g., molecular dynamics, structural dynamics). Third, we present a novel technique for decreasing the temporal complexity --defined as the number of Newton-like iterations performed over the course of the simulation--by exploiting time-domain data. Fourth, we describe a novel method for refining projection-based reduced-order models a posteriori using a goal-oriented framework similar to mesh-adaptive h -refinement in finite elements. The technique allows the ROM to generate arbitrarily accurate solutions, thereby providing the ROM with a 'failsafe' mechanism in the event of insufficient training data. Finally, we present the reduced-order model error surrogate (ROMES) method for statistically quantifying reduced- order-model errors. This enables ROMs to be rigorously incorporated in uncertainty-quantification settings, as the error model can be treated as a source of epistemic uncertainty. This work was completed as part of a Truman Fellowship appointment. We note that much additional work was performed as part of the Fellowship. One salient project is the development of the Trilinos-based model-reduction software module Razor , which is currently bundled with the Albany PDE code and currently allows nonlinear reduced-order models to be constructed for any application supported in Albany. Other important projects include the following: 1. ROMES-equipped ROMs for Bayesian inference: K. Carlberg, M. Drohmann, F. Lu (Lawrence Berkeley National Laboratory), M. Morzfeld (Lawrence Berkeley National Laboratory). 2. ROM-enabled Krylov-subspace recycling: K. Carlberg, V. Forstall (University of Maryland), P. Tsuji, R. Tuminaro. 3. A pseudo balanced POD method using only dual snapshots: K. Carlberg, M. Sarovar. 4. An analysis of discrete v. continuous optimality in nonlinear model reduction: K. Carlberg, M. Barone, H. Antil (George Mason University). Journal articles for these projects are in progress at the time of this writing.

97 MATHEMATICS AND COMPUTING↗