Search NASA⌕ Search

SEARCH · Search NASA

Results for “column generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Optimizing Power Reclamation of Micro Hydro Turbines in WWTPs Aeration Basins

Abstract This study investigates the optimum operating conditions and design configurations that can optimize the power reclaimed by small hydro turbines derived by the rising water-bubble current. The rising current is generated by the compressed air introduced by the diffusers at the bottom of aeration basins of Wastewater Treatment Plants (WWTPs). While optimizing the power production, the standard oxygen transfer efficiency (SOTE) is monitored since it is a significant parameter that cannot be sacrificed in the operation of WWTPs. Using one set of turbine blades, it was found out that the highest velocity is obtained in the upper half of the water column (70% - 80%). In contrast, the lowest velocities were obtained just above the air diffuser and at the water surface. Testing started with using a single turbine (ST) to determine the location of the optimum power reclaimed at each tested airflow (1.18, 1.42, 1.65, and 1.89 L/s). Then using double turbine (DT) and triple turbine (TT) to compare their performance to the ST’s maximum power increased power reclamation. The maximum percentage of increase in power reclamation for DT is 19.59%, while it is 20.24% in the case of TT. At a commonly used airflow in WWTPs (1.42 L/s), the optimum configurations of DTs and TTs were selected to investigate the effect of having the proposed setup on the SOTE. For membrane diffusers, DTs and TTs limited the dispersion of the air bubbles in the tank, therefore, reducing the SOTE (8.3% for DT and 3.7% for the TT). The ceramic and sharp-nub diffusers were also tested versus rubber membrane ones to determine the effect of using the ceramic and sharp-nub diffusers on the power reclamation and SOTE. Ceramic diffusers neither achieve higher power reclamation than the membrane nor increases the SOTE. In contrast, sharp-nub diffusers increase the SOTE for all configurations compared to membranes, but this came into account of power reclamation, where sharp-nub diffusers cause a DT and a TT to produce less power than ST does.

Energy & Fuels↗
DOE OSTI2024

Structure and dynamics of magneto-inertial, differentially rotating laboratory plasmas

We present a detailed characterization of the structure and evolution of differentially rotating plasmas driven on the MAGPIE pulsed-power generator (1.4 MA peak current, 240 ns rise time). The experiments were designed to simulate physics relevant to accretion discs and jets on laboratory scales. A cylindrical aluminium wire array Z pinch enclosed by return posts with an overall azimuthal off-set angle was driven to produce ablation plasma flows that propagate inwards in a slightly off-radial trajectory, injecting mass, angular momentum and confining ram pressure to a rotating plasma column on the axis. However, the plasma is free to expand axially, forming a collimated, differentially rotating axial jet that propagates at ${\approx }100\,{\rm km}\,{\rm s}^{-1}$ . The density profile of the jet corresponds to a dense shell surrounding a low-density core, which is consistent with the centrifugal barrier effect being sustained along the jet's propagation. We show analytically that, as the rotating plasma accretes mass, conservation of mass and momentum implies plasma radial growth scaling as $r \propto t^{1/3}$ . As the characteristic moment of inertia increases, the rotation velocity is predicted to decrease and settle on a characteristic value ${\approx }20\,{\rm km}\,{\rm s}^{-1}$ . We find that both predictions are in agreement with Thomson scattering and optical self-emission imaging measurements.

Valenzuela-Villaseca, V. (ORCID:0000000167721441)↗
DOE OSTI2021

Dynamic Process Intensification via Data-Driven Dynamic Optimization: Concept and Application to Ternary Distillation

Process intensification is a design philosophy aimed at making chemical processes safer and more efficient. Its implementation often results in significant modifications to the design and structure of the process, with several conventional unit operations occurring in the same physical device. Traditionally, process intensification has focused on steady-state operation. In our previous works, we introduced dynamic process intensification (DPI) as a new intensification paradigm based on operational changes for conventional or intensified units. DPI is predicated on switching operation between two auxiliary steady states selected via a steady-state optimization calculation that ensures that the system generates, on average and over time, the same products as in nominal steady-state operation, but with favorable economics. This paper extends the DPI concept and introduces a novel dynamic optimization-based DPI strategy (Do-DPI) that involves imposing a true cyclic operation rather than switching between two discrete states. We discuss its implementation using surrogate dynamic models learned via system identification. Here, an extensive case study concerning a ternary distillation column separating a canonical hydrocarbon mixture shows that Do-DPI can reduce energy use by more than 4% relative to steady-state operation, with no significant deviations in product quality and production rate.

42 ENGINEERING↗
DOE OSTI2020

Gas-phase molybdenum-99 separation from uranium dioxide by fluoride volatility using nitrogen trifluoride

Production of the important 99m Tc medical isotope parent, molybdenum-99 ( 99 Mo), via the fissioning of high- and low-enriched uranium (HEU/LEU) targets followed by target dissolution in acid and solution-phase purification of 99 Mo is time-consuming, generates quantities of corrosive radioactive waste, and can result in the release of an array of radionuclides to the atmosphere. An alternative 99 Mo purification method has been devised that has the potential to alleviate many of these issues. Herein, we demonstrate the feasibility of a rapid Mo/Tc gas-phase separation from UO 2 . The results indicate that volatile [ 99 Mo]Mo can be captured downstream of the reacted solid mixture on a column bed (trap) of alumina; the majority of the captured [ 99 Mo]Mo can be subsequently eluted from the alumina trap with a few milliliters of water. >1.0 × 10 5 single pass decontamination of U and the collected [ 99 Mo]Mo product is demonstrated. This simple thermo-fluorination technique has the potential to provide a rapid methodology for routine 99 Mo production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

X-ray self-emission imaging with spherically bent Bragg crystals on the Z-machine

Here, an x-ray imaging scheme using spherically bent crystals was implemented on the Z-machine to image x rays emitted by the hot, dense plasma generated by a Magnetized Liner Inertial Fusion (MagLIF) target. This diagnostic relies on a spherically bent crystal to capture x-ray emission over a narrow spectral range (<15 eV), which is established by a limiting aperture placed on the Rowland circle. The spherical crystal optic provides the necessary high-throughput and large field-of-view required to produce a bright image over the entire, one-cm length of the emitting column of a plasma. The average spatial resolution was measured and determined to be 18 µm for the highest resolution configuration. With this resolution, the radial size of the stagnation column can be accurately determined and radial structures, such as bifurcations in the column, are clearly resolved. The success of the spherical-crystal imager has motivated the implementation of a new, two-crystal configuration for identifying sources of spectral line emission using a differential imaging technique.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Data and scripts associated with a manuscript on a meta-analysis synthesizing stream biogeochemical response to wildfires across space and time (v2)

This data package is associated with the publication “Catchment characteristics modulate the influence of wildfires on nitrate and dissolved organic carbon in lotic systems across space and time: A meta-analysis” submitted to Global Biogeochemical Cycles (Cavaiani et al. 2025). This study uses meta-analytical techniques to evaluate the effect of wildfire on in-stream responses in burned and unburned watersheds. The study aims to provide additional insight into the range of responses and net influences that wildfires have on hydro-biogeochemistry across broad spatial scales, burn extents, and the persistence of water-quality change. This study compiles data and metadata from 18 total publications that includes 1) surface water geochemistry data (dissolved organic carbon; nitrate), 2) climate classifications, 3) year of the wildfire, 4) the time lag between when the fire occurred and when the sampling occurred, and 5) study design of the publication. In total, this meta-analysis draws data that spans 8 climate guilds, 3 biomes, 62 watersheds, and 20 unique wildfires. See Sites_meta_data.csv for citations of the papers used in this meta-analysis. All R scripts and the associated data can also be found on GitHub at This data package was originally published in March 2024. It was updated in April 2025 (v2; new and modified files). See the change history section in the readme for more details. This data package contains five primary folders that include the following: (1) inputs; (2) output for analysis; (3) initial plots; (4) R scripts; and (5) GIS data. The data package also contains a data dictionary (dd) that provides column header definitions and a file-level metadata (flmd) file that describes every file. The “inputs” folder contains a list of all publications identified during the formal web search and an indication of whether each publication was included in the final analysis. Additionally, it includes site-level metadata, catchment characteristics, and GIS data for all publications included in the final analysis. The “Output_for_analysis” folder contains all data frames and figures generated from each R script used for additional data analysis. The “initial_plots” folder includes all exploratory figures that will be included in a supplemental and figures that will be submitted with the manuscript for publication. The “R_scripts” folder contains the scripts that perform all the data manipulations, statistical analyses, and plots. The “gis_data” folder includes shape files for each fire included in this meta-analysis. This data package contains the following file types: csv, pdf, jpeg, cpg, dbf, prj, shp, shp.ea.iso.xml, shp.iso.xml, shx.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Radically Engineered Modular Air Separation System with Tailored Oxygen Sorbents

The commercial energy sector relies heavily on fossil fuel conversion, and in the process releases a significant amount of CO 2 . A promising technology to utilize fossil fuels with relatively affordable CO 2 capture is gasification. However, it requires a pure oxygen stream. The current state of the art method to produce oxygen is cryogenic air separation, which supercools air to a liquid, and then using distillation columns to separate the components. While this method has been thoroughly studied, it only has a 25% efficiency from a second law standpoint and therefore requires a significant amount of energy (and associated emissions) for oxygen production. This, then, lowers the incentive for carbon capture within a plant, so alternative methods need to be investigated. One potential method, chemical looping air separation (CLAS), is a promising method to replace state of the art oxygen generation technologies. CLAS utilizes a cyclic redox scheme with an oxygen sorbent to create pure oxygen streams. This approach typically utilizes a dual reactor scheme where the oxygen deficient sorbent enters the first reactor and is subjected to high oxygen partial pressures to re-oxidize the sorbent. Then the sorbent is sent to the reducing reactor, where it is subjected to low oxygen partial pressure (steam or vacuum) to releases oxygen. The overarching objective of this project was to discover the principles for rational design and optimization of oxygen sorbents and process design to ensure the process is a viable replacement for cryogenic air separation, especially in the context of modular gasification systems. This was done through development, characterization, testing, and analyses of (a) high temperature mixed composite oxides; (b) low temperature doped perovskite oxides (A1 x A2 1-x B1 y B2 1-y O 3 ); (c) scale up synthesis and testing of the optimized sorbent particles; (d) process design and analyses of the CLAS system in the context of modular gasification applications.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Nitrogen evolution, NO X formation and reduction in pressurized oxy coal combustion

Oxy-combustion is one of the most prominent solutions for reducing CO 2 emissions from coal-fired power plants using carbon-capture-and-utilization technology. However, when compared to air combustion at atmospheric pressure, oxy-combustion is very expensive, owing to the significant efficiency penalties associated with air separation, flue gas recirculation (FGR), treatment, compression, and storage or transit of CO 2 . In comparison, pressurized oxy-combustion (POC) is more efficient as it recovers a significant amount of heat energy from the flue gas moistures. Nevertheless, CO 2 derived from pressurized oxy coal combustion has impurities, e.g., acid gases (NO X and SO X ) that can corrode the plant equipment, transport lines as well as deteriorating effect on the environment. Fortunately, in pressurized combustion systems, both NO X and SO X can be scrubbed by a single-column direct contact cooler (DCC), but this requires a minimum ratio of NO X to SO X at the inlet to be efficiently removed. Therefore, NOx is one of the important hindering parameters in commercializing the pressurized oxy-combustion. Although NOx evolution during oxy-coal combustion has been explored extensively at 1 atm, higher pressure studies are rare. Much still needs to be done to better understand the NO X mechanism and the effects of different parameters on NO X emissions under these conditions. Here, this paper reviews the published literature on nitrogen evolution, NO X formation and reduction in pressurized oxy-coal combustion. At higher pressures, the NO X from fuel-bound nitrogen is generated through volatiles, tar and char, all of which are discussed. Where literature is not available, the effect of pressure on NOx evolution in different stages of coal combustion is predicted through CHEMKIN simulation. Homogeneous and heterogeneous pathways of NO X formation and their destruction in pressurized oxy-coal combustion are evaluated. Additionally, the effect of pressure on a few mature and commercialized NOx abatement methods is explored. In the last, the future perspective and recommendation are given. This review will aid in the provision of basic knowledge about NOx evolution and control in pressurized fuel combustion, as well as the identification of new research areas to pursue.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Extraction of selenium and arsenic with TOA-impregnated XAD-2 resin from HCl

Here the uptake of 75 Se and 73 As on trioctylamine-impregnated resin from HCl solutions was studied with batch uptake, kinetics, and column studies. Selenium-75 extracts well (D w ~ 900) at high HCl concentrations (≥ 10 M) with and no extraction of 73 As at any HCl concentration. The uptake kinetics were slow with low extraction (D w < 100) for time periods ≤ 15 min and no clear equilibrium achieved even after 24 h. Column studies were performed to characterize the separation of 75 Se and 73 As; 75Se is retained from conc. HCl while arsenic is eluted with high yields and high radiopurity.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2025

High-Rate Sputter Deposition of Ultrathick Boron Carbide Coatings on Rolling Spherical Substrates

Amorphous boron carbide (B 4 C) is a promising next-generation ablator material for inertial confinement fusion. However, the deposition of ultrathick B4C coatings with submicron-scale density uniformity on spherical substrates, as required for ablator shell fabrication, remains challenging. Here, in this study, we use direct current magnetron sputtering to deposit B 4 C onto 2-mm-diameter Si spheres rolling in a dish-shaped substrate holder. High deposition rates of ∼3 μm/h are achieved. Ultrathick films have a columnar microstructure, with the column width determined by the density of nodular defects. Nodular defect nucleation is dominated by the pickup of particulates from the holder during substrate rolling. We demonstrate the fabrication of a hollow B 4 C spherical shell with a wall thickness of 80 μm. Also demonstrated is the laser machining of holes in the B 4 C coating, which is necessary for both the chemical removal of the Si template and the attachment of a fusion fuel fill tube.

Inertial confinement fusion targets↗
DOE OSTI2022

Oxygen Solubility in Aqueous Amine Solvents with Common Additives Used for CO 2 Chemical Absorption

Major sources of anthropogenic CO 2 are power generation and transportation industries where researcher continue to explore CO 2 emission mitigation strategies as applied to these CO 2 sources through carbon capture, utilization, and sequestration (CCUS). The most mature CO 2 capture technology is post-combustion carbon capture (PCCC) using aqueous amine solutions/solvents, however solvent degradation and regeneration costs are slowing the widespread adoption of PCCC. Solvent degradation of the aqueous amine solutions is mainly caused from the temperature gradient between the absorber and stripper columns and common flue gas components such as SOx, NOx, and oxygen (O 2 ). The two main classifications of solvent degradation are thermal degradation, occurring when the amine reacts with itself at elevated temperatures and anaerobic conditions and oxidative degradation. Oxidative degradation reactions can occur from oxygen mass transfer and free radical oxidation. Metals, such as iron from the corrosion of steel structures used in industrial applications such as PCCC, can help to catalyze these reactions. Various oxidative degradation studies have shown how O 2 concentrations in flue gas and, to a lesser extent, temperature influence the extent of oxidative degradation. Accurately measuring the O 2 solubility, commonly referred to as dissolved oxygen (DO), in a quick, continuous, and efficient manner in aqueous amine solvents should contribute to determine the effectiveness of mitigation strategies for oxidative degradation. Knowing that commercial PCCC amine solvents contain components beyond water, amine, carbonate species and CO 2 , this investigation was conducted to determine the oxygen solubility changes of common aqueous amines solutions with commonly used and published solvent additives. The impact of carbon loadings with and without the additives was also examined. A commercial dissolved oxygen probe was used to measure the DO concentrations and compared them against standard Winkler Method titration values. The results show that antifoam shows minimal change in [DO]. MBT yielded lower DO values, and NaVO 3 showed a higher DO concentration due to interferences. These results indicate that most common amine solvent additives should be expected to minimally impact oxygen solubility and amine oxidative degradation.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

GRB 221009A: Discovery of an Exceptionally Rare Nearby and Energetic Gamma-Ray Burst

We report the discovery of the unusually bright long-duration gamma-ray burst (GRB), GRB 221009A, as observed by the Neil Gehrels Swift Observatory (Swift), Monitor of All-sky X-ray Image, and Neutron Star Interior Composition Explorer Mission. This energetic GRB was located relatively nearby (z = 0.151), allowing for sustained observations of the afterglow. The large X-ray luminosity and low Galactic latitude (b = 4$^°_.$3) make GRB 221009A a powerful probe of dust in the Milky Way. Using echo tomography, we map the line-of-sight dust distribution and find evidence for significant column densities at large distances (≳10 kpc). We present analysis of the light curves and spectra at X-ray and UV–optical wavelengths, and find that the X-ray afterglow of GRB 221009A is more than an order of magnitude brighter at T 0 + 4.5 ks than that from any previous GRB observed by Swift. In its rest frame, GRB 221009A is at the high end of the afterglow luminosity distribution, but not uniquely so. In a simulation of randomly generated bursts, only 1 in 10 4 long GRBs were as energetic as GRB 221009A; such a large E γ,iso implies a narrow jet structure, but the afterglow light curve is inconsistent with simple top-hat jet models. Using the sample of Swift GRBs with redshifts, we estimate that GRBs as energetic and nearby as GRB 221009A occur at a rate of ≲1 per 1000 yr—making this a truly remarkable opportunity unlikely to be repeated in our lifetime.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Optimal Design and Operation of Intensified Absorbers with 3D-Printed Packing for Solvent-Based CO 2 Capture

Many potential solvent-based carbon capture processes suffer from a high heat of absorption of CO 2 that adversely affects the thermodynamic driving force. While interstage coolers are often used for removing a portion of the generated heat by removing the solvent or a portion of the solvent from a stage and cooling and returning it back to the absorber, they can be placed only at discrete locations in the tower. This work investigates intensified absorbers with 3D-printed packing that includes an internal cooler and therefore can be potentially used for maximizing the operational efficiency of the absorbers for CO 2 capture. The intensified absorber is modeled by using a generic, first-principles, equation-oriented absorber column model. Since the placement of these intensified packings would cause a loss of area/volume used for mass transfer, optimization of the proposed intensified absorber is performed by optimally selecting the locations at which to place these devices and designing them such that the trade-off due to the addition of the heat removal area and the resulting loss in the mass transfer area is accounted for. Results show that optimally placed and designed intensified packings can lead to a significant increase in the capture efficiency of the process in comparison to a similar column with no internal cooling. It is also observed that by optimally placing and designing intensified packings, the lean solvent flow rate to the absorber can be decreased, and the CO 2 lean loading can be increased while still maintaining the same capture efficiency. These process changes can lead to a substantial reduction in the cost of capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

ARM Data-Oriented Metrics and Diagnostics Package for Climate Model Evaluation

A Python-based metrics and diagnostics package is currently being developed by the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Infrastructure Team at Lawrence Livermore National Laboratory (LLNL) to facilitate the use of long-term, high-frequency measurements from the ARM Facility in evaluating the regional climate simulation of clouds, radiation, and precipitation. This metrics and diagnostics package computes climatological means of targeted climate model simulation and generates tables and plots for comparing the model simulation with ARM observational data. The Coupled Model Intercomparison Project (CMIP) model data sets are also included in the package to enable model intercomparison as demonstrated in Zhang et al. (2017). The mean of the CMIP model can serve as a reference for individual models. Basic performance metrics are computed to measure the accuracy of mean state and variability of climate models. The evaluated physical quantities include cloud fraction, temperature, relative humidity, cloud liquid water path, total column water vapor, precipitation, sensible and latent heat fluxes, and radiative fluxes, with plan to extend to more fields, such as aerosol and microphysics properties. Process-oriented diagnostics focusing on individual cloud- and precipitation-related phenomena are also being developed for the evaluation and development of specific model physical parameterizations. The version 1.0 package is designed based on data collected at ARM’s Southern Great Plains (SGP) Research Facility, with the plan to extend to other ARM sites. The metrics and diagnostics package is currently built upon standard Python libraries and additional Python packages developed by DOE (such as CDMS and CDAT). The ARM metrics and diagnostic package is available publicly with the hope that it can serve as an easy entry point for climate modelers to compare their models with ARM data. In this report, we first present the input data, which constitutes the core content of the metrics and diagnostics package in section 2, and a user's guide documenting the workflow/structure of the version 1.0 codes, and including step-by-step instruction for running the package in section 3.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Co-Development of Oscillating Water Column (OWC) and Offshore Power Station

The project proposed an Oscillating Water Column (OWC) at a low power rating (1-5kW); to build a prototype and perform field testing within 1–3 years and achieving a commercial version of the OWC 3–5 years. We selected the OWC off-the-shelf components to secure the supply-chain sources and to warrant stable and minimum pricing. We want to curtail the capital cost by reducing the weight and volume of the overall system structure at the design level by designing a high-speed turbine generator and optimizing the airspeed amplification. We want to minimize the operational and maintenance (O&M) costs through simplified architecture, minimal parts, modular/plug-and-play, and easy access designs.

16 TIDAL AND WAVE POWER↗
DOE OSTI2020

Native glycosylated HIV-1 Env in silico ensemble

The computationally modeled datasets generated in this study, namely the natively glycosylated SOSIP Env and the uniform mannose-9 glycosylated SOSIP Env ensembles will be submitted as Mendeley dataset server as required by the journal publishers, for public availability. These include two sets of Protein Data Bank (PDB)ensembles of 1000 structures each. The files are in the standardized PDB format. Each of the constituent ensemble structures are separated by the ‘END’ tag within the files. Snapshots from the beginning and end of each data set are given here. The column descriptions are as follows: Col1 –ATOM tag; Col 2 –atom number; COL 3 –atom name; COL4 –residue name; COL 5 –chain identifier; COL 6 –residue number; COL. 7,8,9 –X,Y,Z coordinates of atom in 3Dspace; COL 10 –Occupancy Factor; COL 11 -Temperature factor; COL 12 –segment identifier; COL 13 –element symbol.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Qualification of Processing Batches for Tank Closure Cesium Removal Through In-Tank Batch Contact Testing - 20470

The Tank Closure Cesium Removal (TCCR) process at the Savannah River Site (SRS) is currently processing waste from Tank 10H, generating decontaminated salt solution that is sent to Tank 11H. Transfers out of Tank 11H are then disposed of on site as a grout wasteform in the SRS Saltstone Processing Facility. This is a full-scale demonstration of the use of Crystalline Silicotitanate (CST) for the decontamination of aqueous nuclear waste supernate. CST primarily removes cesium from the high sodium alkaline feed, but also adsorbs strontium, actinides, and some other trace metals. The TCCR unit is an at-tank set of four ion exchange columns, with two typically being operated in series during waste processing. Tank 10H is serving a dual function as both the salt dissolution tank as well as the feed tank for the TCCR system. Prior to operation of TCCR, Tank 10H must undergo dissolution campaigns, dissolving the salt cake to form an aqueous salt solution (supernate). After each dissolution campaign, the supernate created must be qualified prior to processing through the TCCR system. Qualification includes detailed characterization of the supernate as well as in-tank batch contact tests to determine the equilibrium loading of Cs-137 on the CST ion exchange media (IONSIV{sup TM} R9120-Ba). In support of the in-tank batch contact testing, Savannah River National Laboratory (SRNL) developed a CST sample holder, also referred to as a 'tea-bag', to hold a measured amount (∼0.1 grams) of pretreated CST between stainless steel screens. The tea-bag fits within a standard stainless steel sample vial that has been modified to allow the flow of supernate to the CST. This sample holder is then immersed in the waste tank allowing free contact between the CST beads and the surrounding liquid, at an effectively infinite liquid-to-solid phase ratio. A pair of tea-bags are deployed in the tank for a period of 10 days for each batch, after which the CST is recovered, digested, and analyzed to determine the loading of cesium isotopes on the CST. This result then supports the TCCR column thermal loading limits for processing as part of the TCCR safety basis. This paper will discuss the design and testing of the CST sample holder, as well as results from the first few batches of waste qualified and subsequently processed through the TCCR system. In addition, results from analyses of Tank 11H samples, showing decontamination of the product will be included. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

On the differences in the vertical distribution of modeled aerosol optical depth over the southeastern Atlantic

Abstract. The southeastern Atlantic is home to an expansive smoke aerosol plume overlying a large cloud deck for approximately a third of the year. The aerosol plume is mainly attributed to the extensive biomass burning activities that occur in southern Africa. Current Earth system models (ESMs) reveal significant differences in their estimates of regional aerosol radiative effects over this region. Such large differences partially stem from uncertainties in the vertical distribution of aerosols in the troposphere. These uncertainties translate into different aerosol optical depths (AODs) in the planetary boundary layer (PBL) and the free troposphere (FT). This study examines differences of AOD fraction in the FT and AOD differences among ESMs (WRF-CAM5, WRF-FINN, GEOS-Chem, EAM-E3SM, ALADIN, GEOS-FP, and MERRA-2) and aircraft-based measurements from the NASA ObseRvations of Aerosols above CLouds and their intEractionS (ORACLES) field campaign. Models frequently define the PBL as the well-mixed surface-based layer, but this definition misses the upper parts of decoupled PBLs, in which most low-level clouds occur. To account for the presence of decoupled boundary layers in the models, the height of maximum vertical gradient of specific humidity profiles from each model is used to define PBL heights. Results indicate that the monthly mean contribution of AOD in the FT to the total-column AOD ranges from 44 % to 74 % in September 2016 and from 54 % to 71 % in August 2017 within the region bounded by 25∘ S–0∘ N–S and 15∘ W–15∘ E (excluding land) among the ESMs. ALADIN and GEOS-Chem show similar aerosol plume patterns to a derived above-cloud aerosol product from the Moderate Resolution Imaging Spectroradiometer (MODIS) during September 2016, but none of the models show a similar above-cloud plume pattern to MODIS in August 2017. Using the second-generation High Spectral Resolution Lidar (HSRL-2) to derive an aircraft-based constraint on the AOD and the fractional AOD, we found that WRF-CAM5 produces 40 % less AOD than those from the HSRL-2 measurements, but it performs well at separating AOD fraction between the FT and the PBL. AOD fractions in the FT for GEOS-Chem and EAM-E3SM are, respectively, 10 % and 15 % lower than the AOD fractions from the HSRL-2. Their similar mean AODs reflect a cancellation of high and low AOD biases. Compared with aircraft-based observations, GEOS-FP, MERRA-2, and ALADIN produce 24 %–36 % less AOD and tend to misplace more aerosols in the PBL. The models generally underestimate AODs for measured AODs that are above 0.8, indicating their limitations at reproducing high AODs. The differences in the absolute AOD, FT AOD, and the vertical apportioning of AOD in different models highlight the need to continue improving the accuracy of modeled AOD distributions. These differences affect the sign and magnitude of the net aerosol radiative forcing, especially when aerosols are in contact with clouds.

54 ENVIRONMENTAL SCIENCES↗