Search NASA⌕ Search

SEARCH · Search NASA

Results for “computational fluid dynamics simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

The effects of boost pressure on stratification and burn duration of gasoline homogeneous charge compression ignition combustion

This article investigates the effects of intake pressure (boost) on the pre-ignition stratification and burn duration of homogeneous charge compression ignition combustion. Full cycle computational fluid dynamics simulations are performed with gasoline kinetics. An intake pressure sweep is performed while maintaining the same combustion timing and mean composition. The burn duration reduces with increasing boost, even though intake temperature is reduced to hold combustion timing constant. It is shown that the compositional stratification increases with boost whereas thermal stratification decreases. A quasi-dimensional model is employed to assess the effect of compositional stratification, pressure, mean temperature and isolate the effect of thermal stratification on burn duration. The analysis reveals that reducing charge temperature neutralizes the effect of increased boost on reactivity and the shorter burn durations at higher boost are primarily due to the lower thermal stratification. It is shown that higher pressures do not significantly increase the mixing and the lower thermal stratification is due to lower wall heat losses per unit charge mass. A follow-up set of non-reacting simulations with adiabatic walls corroborate this claim by revealing a constant magnitude of thermal stratification across the boost sweep.

Shingne, Prasad S.↗

Effects of a CFD-improved dimple stepped-lip piston on thermal efficiency and emissions in a medium-duty diesel engine

Diesel piston-bowl shape is a key design parameter that affects spray-wall interactions and turbulent flow development, and in turn affects the engine’s thermal efficiency and emissions. It is hypothesized that thermal efficiency can be improved by enhancing squish-region vortices as they are hypothesized to promote fuel-air mixing, leading to faster heat-release rates. However, the strength and longevity of these vortices decrease with advanced injection timings for typical stepped-lip (SL) piston geometries. Dimple stepped-lip (DSL) pistons enhance vortex formation at early injection timings. Previous engine experiments with such a bowl show 1.4% thermal efficiency gains over an SL piston. However, soot was increased dramatically [SAE 2022-01-0400]. In a previous study, a new DSL bowl was designed using non-combusting computational fluid dynamic simulations. This improved DSL bowl is predicted to promote stronger, more rotationally energetic vortices than the baseline DSL piston: it employs shallower, narrower, and steeper-curved dimples that are placed further out into the squish region. In the current experimental study, this improved bowl is tested in a medium-duty diesel engine and compared against the SL piston over an injection timing sweep at low-load and part-load operating conditions. No substantial thermal efficiency gains are achieved at the early injection timing with the improved DSL design, but soot emissions are lowered by 45% relative to the production SL piston, likely due to improved air utilization and soot oxidation. However, these benefits are lost at late injection timings, where the DSL piston renders a lower thermal efficiency than that of the SL piston. Energy balance analyses show higher wall heat transfer with the DSL piston than with the SL piston despite a 1.3% reduction in the piston surface area. Vortex enhancement may not necessarily lead to improved efficiency as more energetic squish-region vortices can lead to higher convective heat transfer losses.

42 ENGINEERING↗

THERMAL ANALYSIS OF A PROPOSED TRANSPORT CASK FOR THREE ADVANCED BURNER REACTOR USED FUEL ASSEMBLIES

Preliminary studies of used fuel generated in the US Department of Energy’s Advanced Fuel Cycle Initiative have indicated that current used fuel transport casks may be insufficient for the transportation of said fuel. This work considers transport of three 5-year-cooled oxide Advanced Burner Reactor used fuel assemblies with a burn-up of 160 MWD/kg. A transport cask designed to carry these assemblies is proposed. This design employs a 7-cm-thick lead gamma shield and a 20-cm-thick NS-4-FR composite neutron shield. The temperature profile within the cask, from its center to its exterior surface, is determined by two dimensional computational fluid dynamics simulations of conduction, convection, and radiation within the cask. Simulations are performed for a cask with a smooth external surface and various neutron shield thicknesses. Separate simulations are performed for a cask with a corrugated external surface and a neutron shield thickness that satisfies shielding constraints. Resulting temperature profiles indicate that a three-assembly cask with a smooth external surface will meet fuel cladding temperature requirements but will cause outer surface temperatures to exceed the regulatory limit. A cask with a corrugated external surface will not exceed the limits for both the fuel cladding and outer surface temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An investigation into the potential for wind turbines to cause barotrauma in bats

The high rates of bat mortality caused by operating wind turbines is a concern for wind energy and wildlife stakeholders. One theory that explains the mortality is that bats are not only killed by impact trauma, but also by barotrauma that results from exposure to the pressure variations caused by rotating turbine blades. To date, no published research has calculated the pressure changes that bats may be exposed to when flying near wind turbines and then used these data to estimate the likelihood that turbines cause barotrauma in bats. To address this shortcoming, we performed computational fluid dynamics simulations of a wind turbine and analytical calculations of blade-tip vortices to estimate the characteristics of the sudden pressure changes bats may experience when flying near a utility-scale wind turbine. Because there are no data available that characterize the pressure changes that cause barotrauma in bats, we compared our results to changes in pressure levels that cause barotrauma and mortality in other mammals of similar size. This comparison shows that the magnitude of the low-pressures bats experience when flying near wind turbines is approximately 8 times smaller than the pressure that causes mortality in rats, the smallest mammal for which data are available. The magnitude of the high-pressures that bats may experience are approximately 80 times smaller than the exposure level that causes 50% mortality in mice, which have a body mass similar to several bat species that are killed by wind turbines. Further, our results show that for a bat to experience the largest possible magnitude of low- and high-pressures, they must take very specific and improbable flight paths that skim the surface of the blades. Even a small change in the flight path results in the bat being hit by the blade or experiencing a much smaller pressure change. Accordingly, if bats have a physiological response to rapid low- and high-pressure exposure that is similar to other mammals, we conclude that it is unlikely that barotrauma is responsible for a significant number of turbine-related bat fatalities, and that impact trauma is the likely cause of the majority of wind-turbine-related bat fatalities.

17 WIND ENERGY↗

Field Sensitivity Analysis of Turbulence Model Parameters for Flow Over a Wing

Reynolds-averaged-Navier-Stokes (RANS) turbulence models are a critical tool in computational-fluid-dynamics simulations of aerodynamic systems, but simulation results can be highly sensitive to RANS-model parameter choices. Sensitivity analysis can be used to quantify these impacts, and the objective of this study is to demonstrate field sensitivity analysis with respect to ten parameters in the 2003 Menter shear-stress-transport (SST) turbulence model. Here, the analysis is demonstrated for an application relevant to wind energy, namely, flow over a NACA 0015 wing at 12 degree angle of attack and a Reynolds number of 1.5 x 10 6 . We quantify sensitivity using Sobol indices and the mean-squared gradient, which are estimated using polynomial chaos and active subspace models, respectively. Our results indicate that there are substantial spatial variations in parameter sensitivities, with different sets of most-sensitive parameters near the wing, as well as in the downstream wake, consistent with the physical interpretations of the turbulence model inputs. We show that, for this particular turbulence model and flow, simultaneous dimension reduction is possible across all quantities of interest, enabling efficient exploration of model outcomes. Ultimately, this analysis provides new insights into turbulence model parameter sensitivities in incompressible flows, and also demonstrates the implementation of field sensitivity analysis for applications relevant to aerodynamics simulations.

17 WIND ENERGY↗

Development and Implementation of 3-D, High Speed Capacitance Tomography for Imaging Large-Scale, Cold-Flow Circulating Fluidized Bed

A detailed understanding of multiphase flow behavior inside a Circulating Fluidized Bed (CFB) requires a 3-D technique capable of visualizing the flow field in real-time. Electrical Capacitance Volume Tomography (ECVT) is a newly developed technique that can provide such measurements. The attractiveness of the technique is in its low profile sensors, fast imaging speed and scalability to different section sizes, low operating cost, and safety. Moreover, the flexibility of ECVT sensors enable them to be designed around virtually any geometry, rendering them suitable to be used for measurement of solid flows in exit regions of the CFB. Tech4Imaging LLC has worked under contract with the U.S. Department of Energy's National Energy Technology Laboratory (DOE NETL) to develop an ECVT system for cold flow visualization and install it on a 12 inch ID circulating fluidized bed. The objective of this project was to help advance multi-phase flow science through implementation of an ECVT system on a cold flow model at DOE NETL. This project has responded to multi-phase community and industry needs of developing a tool that can be used to develop flow models, validate computational fluid dynamics simulations, provide detailed real-time feedback of process variables, and provide a comprehensive understating of multi-phase flow behavior. In this project, a complete ECVT system was successfully developed after considering different potential electronics and sensor designs. The system was tested at various flow conditions and with different materials, yielding real-time images of flow interaction in a gas-solid flow system. The system was installed on a 12 inch ID CFB of the US Department of Energy, Morgantown Labs. Technical and economic assessment of Scale-up and Commercialization of ECVT was also conducted. Experiments conducted with larger sensors in conditions similar to industrial settings are very promising. ECVT has also the potential to be developed for imaging multi-phase flow systems in high temperature and high pressure conditions, typical in many industrial applications.

42 ENGINEERING↗

Validation of Pin Span Superposition to Reconstruct Gridded Bundle Flows

This milestone shows a demonstration of the surface map model to map the surface temperature for single-phase computational fluid dynamics simulation data from STAR-CCM+ to the subchannel code CTF using a two-step process that captures global and local rod surface temperature behavior based on simulation boundary conditions and position. This model can be used to improve results from CTF by transforming surface temperatures obtained from CTF to model data that resembles data from STAR-CCM+. A summary of the current two-step model process and results of the initial investigations with a single subchannel and a 5 x 5 set of fuel rods are shown and discussed within, with suggestions for further improvements.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Air Blast Mesh Sensitivity and Pressure Mapping Study

Nose cone structural and aerodynamic characteristics are essential for intelligent design of aircraft, spacecraft, and ballistic systems. Finite element analysis can be used to help understand the structural integrity and flight characteristics of different nose cones. A mesh sensitivity study was undertaken for a particular nose cone geometry that was used in tests at LANL facilities in order to confirm the integrity of the meshed geometry. A simple cone that best matched closed-form theoretical solutions was modeled, and received good correlation to the theory. Complexity was then added back to the nose cone. Parameters applied to the simple cone were then implemented in the nose cone geometry giving assurance of accuracy after the geometry was changed. Nose cone results averaged 6.3% error for radial displacement when compared with the theoretical. Hoop stress averaged 6.0% error and meridional stress averaged 5.7% error at the finest mesh level. Meshes showed signs of convergence when compared to all three theoretical solutions. Finally, pressure time-history data from LANL computational fluid dynamics simulations was applied to the surface of the final nose cone geometry. The pressure data was interpolated from pressure gauge locations onto nearby meshed elements, which allowed for FEA software to run simulations on the cone with the pressure data as a loading condition. The pressure mapping resulted in the ability to understand the nose cone’s rigid body motion that in turn can inform design of future nose cones.

42 ENGINEERING↗

Design and Testing of the Vortex Ring Facility

This document summarizes the efforts of building an experimental test facility to study the evolution of the cloud following a nuclear detonation above ground level and support the development of numerical models to describe it. The experimental facility allows nonintrusive flow visualization and measurements of buoyant vortex ring formation and evolution using background-oriented Schlieren and particle image velocimetry techniques. In addition, 3D unsteady computational fluid dynamics simulations using unsteady Reynolds-averaged Navier–Stokes and volume-of-fluid numerical methods were performed to support the experimental design as well as to provide insight about the formation and evolution of the vortex ring.

42 ENGINEERING↗

Development of Advanced Solid Sorbents for Direct Air Capture (Final Report)

RTI International is partnering with Creare, and Mohammed VI Polytechnic University (UM6P) successfully met all major technical objectives as outlined below: Identified one MOF adsorbent for DAC; Identified one amine-P-dendrimer adsorbent for DAC; Performed Computational fluid dynamics simulations of the MOF and amine-P-dendrimer adsorbents and validate them with experimental data; Selected one adsorbent for DAC; Demonstrated the scale-up of selected candidate and perform cost review; Performed a preliminary process design; Performed technology maturation plan and environmental health and safety risk assessment. After a thorough comparison between both adsorbents (MOFs and P-dendrimers) and based on their technical merits, the amine-based P-dendrimers sorbent was selected as the best performing adsorbent for DAC. In fact, the amine-based P-dendrimers have demonstrated superior performance over the MOF sorbents under relevant DAC conditions. The selected sorbent has been used in subsequent projects (DE-FE0032099 and DE-AR0001412) and has demonstrated similar superior performance with no loss of activity after long-term sorption-desorption testing (e.g., 100 cycles). This sorbent has demonstrated a very high and stable sorption performance, excellent kinetics, and fast regeneration at 80 °C, specifically at 75% relative humidity (RH). The incorporation of RTI’s high-performance, high-durability amine-based P-dendrimers sorbent and Creare’s hybrid additive manufacturing (H-AM) technology that will produce high performance, compact heat and mass exchange structures at low cost using methods, will lead to a contactor that is optimized for wind-driven operation. This contactor technology provides a technically viable pathway for reducing the cost of DAC to <$100/tonne of CO 2 .

36 MATERIALS SCIENCE↗

Development and Porting of Nuclear Reactor Computational Models for the NRIC Virtual Test Bed in FY23

The U.S. DOE’s National Reactor Innovation Center (NRIC) hosts an open-source website and associated GitHub repository called the Virtual Test Bed (VTB) on which computational models for advanced reactors are documented and shared with the reactor community. In FY23 under the NRIC program, computational models for nuclear reactor analysis were developed and contributed to the VTB Github repository during FY23 by contributors at Argonne National Laboratory. Other models developed outside of NRIC were also ported to the VTB as part of this work, serving a broader mission to make computational reactor analysis models more widely available to the reactor community. The model development activities focused on demonstration of gas-cooled microreactor models including computational fluid dynamics simulations of flow through an industry-inspired air jacket design, and simulation of multiphysics transients for a gas-cooled microreactor assembly. Additionally, development of a molten salt reactor (led at Idaho National Laboratory) was supported through Argonne’s expertise in multigroup cross sections generation. Models for these two reactor types were targeted due to their relevancy to NRIC’s Demonstration of Microreactor Experiments (DOME) and Laboratory for Operation and Testing in the U.S. (LOTUS) physical test beds, which are slated to host microreactor and molten salt reactor experiments. The model porting activities consisted of developing detailed documentation for several physics models which originate from the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. We include only contributions from Argonne National Laboratory in this report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Highly Permeable Rubbery Thin Film Composite Membranes for CO2 Capture from Steel Mills

This presentation will report the rational design and fabrication of NETL’s highly permeable non-aging thin film composite (TFC) membranes for CO2 capture from various industrial point sources. This talk will also cover the design, computational fluid dynamic simulation, 3D printing, and permeation testing of plate-and-frame membrane modules for an upcoming field demonstration at U. S. Steel’s Edgar Thomson Plant in Braddock, PA. The field test will demonstrate membrane-based CO2 capture from a blast furnace for decarbonization of steel manufacturing for the first time in the U.S. A mobile gas permeation test unit is currently under design and construction for the field test, which is scheduled to take place in 2025.

Zhu, Lingxiang↗

Highly Permeable Rubbery Thin Film Composite Membranes for CO2 Capture from Steel Mills

For presentation at the 2024 AIChE Annual Meeting, San Diego, CA, October 27-31, 2024. High-permeance and CO2-selective membranes are needed to make membrane technology economically viable for large-scale deployment of carbon capture from various industrial point sources such as steel mills. Thin film composite (TFC) membranes are necessary for this practical implementation because they can provide high permeance by forming a thin selective layer on top of a porous support layer. This presentation reports the rational design and fabrication of National Energy Technology Laboratory’s highly permeable non-aging TFC membranes achieved by: (1) synthesizing a high-performance rubbery selective material; (2) developing a high-porosity membrane support; (3) optimizing coating methods to assemble the two materials into scalable membranes; and (4) scaling up membrane supports and TFCs via a roll-to-roll process. This talk will also cover the design, computational fluid dynamic simulation, 3D printing, construction, and permeation testing of plate-and-frame membrane modules for an upcoming field demonstration at U. S. Steel’s Edgar Thomson Plant in Braddock, PA.

Zhu, Lingxiang↗

Selective Thermal Emission with Radiation and Adsorption in Annuli (STERADIAN): An Advanced Heat Exchanger Concept for Supercritical CO 2 Power Cycles

One of the key limitations affecting ability to achieve the efficiency and cost saving advantages of a supercritical CO 2 (scCO 2 ) power cycle resides with the primary heat exchanger where costs can exceed 50% of the plant capital budget depending on design. This project established the foundational groundwork for a new type of heat exchanger optimized to take advantage of radiative heat transfer to scCO 2 . Selective thermal emission coatings were designed and tested that radiated more light tuned to the 4.2 µm infrared absorption band of CO 2 . Coating design utilized principles of nanophotonic bandgap theory to design a selective emitter that has: 1) low emissivity in the visible band, 2) near 100% effective emissivity in the mid-IR wavelength between 4 and 4.5 µm wavelength, and 3) strong suppression of far-IR light emission that will maximize radiative heat transfer efficiency to scCO 2 . Computational fluid dynamics simulations show that an advanced heat exchanger implementing this selective thermal emitter coating is 25 to as much as 40% smaller than conventional heat exchanger designs.

14 SOLAR ENERGY↗

Confinement Exploiting Arrays of Cross-Flow Turbines (ConExT) (Final Scientific/Technical Report)

Final technical report for the ARPA-E SHARKS project: Confinement Exploiting Arrays of Cross-Flow Turbines (ConExT). This involved collaboration by the University of Washington, University of Wisconsin, National Renewable Energy Laboratory, and Oberon Insights. Cost-effective, large-scale utilization of tidal and river current resources requires turbine arrays. Most array concepts involve multiple, staggered rows of turbines analogous to wind farms. However, in water, turbines that have an appreciable projected area (i.e., the projected area over a full revolution) relative to a channel’s cross-sectional area can theoretically extract far more energy than when operating in isolation. This suggests substantial benefits to a confinement-exploiting approach to array layout, in which turbines are more densely clustered in a single row spanning a channel. The objective of this project was to move this concept from theory to practice, as well as establishing environmental and economic trade-offs. This objective was accomplished through scale-model experimentation, high-fidelity computational fluid dynamic simulation, and integrated techno-economic modeling.

16 TIDAL AND WAVE POWER↗

Heavy-Duty Vehicle Air Drag Coefficient Estimation: From an Algebraic Perspective

When a heavy-duty vehicle (HDV) operates at the nominal highway speed, over two-thirds of its total resistive force comes from the air drag, contributing to more than half of its fuel consumption. One effective countermeasure to reduce the fuel consumption of HDVs is platooning, which employs connectivity and automated driving technologies to link two or more HDVs in convoy. Platooning allows HDVs to drive closer together and yields improved fuel economy and less CO2 emission thanks to the reduced air drag. Maximizing the energy benefits of an HDV platoon requires quantifying the drag interaction between vehicles. In practice, modeling the drag reduction in a platoon boils down to identifying the relationship between the air drag coefficient C d and the inter-vehicle distance d. Existing approaches to identify C d (d) include vehicle field tests, wind tunnel experiments, and computational fluid dynamics simulation, which can howbeit be time-consuming and cost prohibitive. In contrast, this paper proposes an algebraic approach, which relies on onboard-measurable variables, to estimate the air drag coefficient of an HDV in a platoon. Its algebraic nature avoids the classical persistence of excitation condition for parameter identification and can yield the identified parameter almost instantaneously. Simulation results demonstrate its effectiveness and the improved estimation speed over a recursive least squares identifier.

Wang, Zejiang↗

Particle Size Distribution and Its Impacts on Ash Deposition and Radiative Transfer during Oxy-Combustion of Rice Husk–Natural Gas

Rice husk (RH) co-combustion with natural gas in highly oxygen-enriched concentrations presents a net carbon-negative energy production opportunity while minimizing flue gas recycling. However, recent experiments have shown enhanced ash deposition rates in oxygen-enriched conditions, with deposition/shedding also being dependent on the particle size distribution (PSD) of the parent RH fuel. To uncover the causative mechanisms behind these observations, add-on models for ash deposition/shedding and radiative properties were employed in computational fluid dynamics simulations. The combustion scenarios investigated encompassed two types of RH (US RH, Chinese RH) with widely varying ash contents (by % mass) and inlet fuel PSD with air and O2/CO2 (70/30 vol %, OXY70) as oxidizers. Utilizing the measured fly-ash PSDs near the deposit surface and modeling the particle viscosity accurately, particle kinetic-energy (PKE)-based capture and shedding criteria were identified as the keys to accurate deposition/shedding rate predictions. The OXY70 scenarios showed higher ash-capturing propensities due to their lower PKE. Conversely, higher erosion rates were predicted in the AIR firing scenarios. In addition, the radiative characteristics across all the scenarios were dominated by the gases and were not sensitive to the fly-ash PSD. Therefore, the higher particle concentrations in the OXY70 conditions did not negatively impact the heat extraction.

Krishnamoorthy, Gautham (ORCID:0000000255205092)↗

Achieving Diesel-Like Efficiency in a High Stroke-to-Bore Ratio DISI Engine under Stoichiometric Operation

This work explores pathways to achieve diesel-like, high-efficiency combustion with stoichiometric 3-way catalyst compatible spark ignition (SI). A high stroke-to-bore engine design (1.5:1) with cooled exhaust gas recirculation (EGR) and high compression ratio (r c ) was used to improve engine efficiency by up to 30% compared with a production turbocharged gasoline direct injection spark ignition engine. To achieve efficiency improvements, engine experiments were coupled with computational fluid dynamics simulations to guide and explain experimental trends between the original engine and the high stroke-to-bore ratio design (1.5:1). The effects of EGR and late intake valve closing (IVC) and fuel characteristics are investigated through their effects on knock mitigation. Direct injection of 91 RON E10 gasoline, 99 RON E0 gasoline, and liquified petroleum gas (i.e., propane/autogas) were evaluated with geometric rc ranging from 13.3:1 to 16.8:1. Finally, engine experiments demonstrated 47% gross thermal efficiency, and 45% net thermal efficiency at stoichiometric engine operation, at up to 17 bar IMEP and 2000 r/min with 16.8:1 rc.

42 ENGINEERING↗