Search NASA⌕ Search

SEARCH · Search NASA

Results for “conceptual design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Conceptual design studies of lift/cruise fans for military transports

A study program for conceptual design studies of remote lift and lift/cruise fan systems to meet the requirements of military V/STOL aircraft was conducted. Parametric performance and design data are presented for fans covering a range of pressure ratios, including both single and two stage fan concepts. The gas generator selected for these fan systems was the J101-GE-100 engine. Noise generation and transient response were determined for selected fan systems.

Source record↗
NASA NTRS1975

Conceptual design of reduced energy transports

This paper reports the results of a conceptual design study of new, near-term fuel-conservative aircraft. A parametric study was made to determine the effects of cruise Mach number and fuel cost on the 'optimum' configuration characteristics and on economic performance. Supercritical wing technology and advanced engine cycles were assumed. For each design, the wing geometry was optimized to give maximum return on investment at a particular fuel cost. Based on the results of the parametric study, a reduced energy configuration was selected. Compared with existing transport designs, the reduced energy design has a higher aspect ratio wing with lower sweep, and cruises at a lower Mach number. It yields about 30% more seat-miles/gal than current wide-body aircraft. At the higher fuel costs anticipated in the future, the reduced energy design has about the same economic performance as existing designs.

Ardema, M. D.↗
NASA NTRS1976

Conceptual design of reduced energy transports

The paper reports the results of a conceptual design study of new near-term fuel-conservative aircraft. A parametric study was made to determine the effects of cruise Mach number and fuel cost on the optimum configuration characteristics and relative economic performance. Supercritical wing technology and advanced engine cycles were assumed. For each design, the wing geometry was selected to maximize an economic figure of merit which reflects the potential rate of return on investment. Based on the results of the parametric study, a reduced energy configuration was selected. Compared with existing transport design, the reduced energy design has a higher aspect ratio wing with lower sweep, and cruises at a slightly lower Mach number. It yields about 30% more seat-miles/gal than current wide-body aircraft. At the higher fuel costs anticipated in the future, the reduced energy design has about the same economic performance as existing designs with the same technology level. As an example of a far-term technology application, a design with a composite material wing was also investigated.

Ardema, M. D.↗
NASA NTRS1978

Conceptual design study of a Harrier V/STOL research aircraft

MCAIR recently completed a conceptual design study to define modification approaches to, and derive planning prices for the conversion of a two place Harrier to a V/STOL control, display and guidance research aircraft. Control concepts such as rate damping, attitude stabilization, velocity command, and cockpit controllers are to be demonstrated. Display formats will also be investigated, and landing, navigation and guidance systems flight tested. The rear cockpit is modified such that it can be quickly adapted to faithfully simulate the controls, displays and handling qualities of a Type A or Type B V/STOL. The safety pilot always has take command capability. The modifications studied fall into two categories: basic modifications and optional modifications. Technical descriptions of the basic modifications and of the optional modifications are presented. The modification plan and schedule as well as the test plan and schedule are presented. The failure mode and effects analysis, aircraft performance, aircraft weight, and aircraft support are discussed.

Bode, W. E.↗
NASA NTRS1980

Conceptual design study for an advanced cab and visual system, volume 1

A conceptual design study was conducted to define requirements for an advanced cab and visual system. The rotorcraft system integration simulator is for engineering studies in the area of mission associated vehicle handling qualities. Principally a technology survey and assessment of existing and proposed simulator visual display systems, image generation systems, modular cab designs, and simulator control station designs were performed and are discussed. State of the art survey data were used to synthesize a set of preliminary visual display system concepts of which five candidate display configurations were selected for further evaluation. Basic display concepts incorporated in these configurations included: real image projection, using either periscopes, fiber optic bundles, or scanned laser optics; and virtual imaging with helmet mounted displays. These display concepts were integrated in the study with a simulator cab concept employing a modular base for aircraft controls, crew seating, and instrumentation (or other) displays. A simple concept to induce vibration in the various modules was developed and is described. Results of evaluations and trade offs related to the candidate system concepts are given, along with a suggested weighting scheme for numerically comparing visual system performance characteristics.

Rue, R. J.↗
NASA NTRS1990

Conceptual design of a Moving Belt Radiator (MBR) shuttle-attached experiment

The conceptual design of a shuttle-attached Moving Belt Radiator (MBR) experiment is presented. The MBR is an advanced radiator concept in which a rotating belt is used to radiate thermal energy to space. The experiment is developed with the primary focus being the verification of the dynamic characteristics of a rotating belt with a secondary objective of proving the thermal and sealing aspects in a reduced gravity, vacuum environment. The mechanical design, selection of the belt material and working fluid, a preliminary test plan, and program plan are presented. The strategy used for selecting the basic sizes and materials of the components are discussed. Shuttle and crew member requirements are presented with some options for increasing or decreasing the demands on the STS. An STS carrier and the criteria used in the selection process are presented. The proposed carrier for the Moving Belt Radiator experiment is the Hitchhiker-M. Safety issues are also listed with possible results. This experiment is designed so that a belt can be deployed, run at steady state conditions, run with dynamic perturbations imposed, verify the operation of the interface heat exchanger and seals, and finally be retracted into a stowed position for transport back to earth.

Aguilar, Jerry L.↗
NASA NTRS1991

Conceptual design of a next-generation, fully reusable manned launch system

The conceptual design of a rocket-powered, two-stage fully reusable launch vehicle has been performed as a part of the Advanced Manned Launch System (AMLS) study at the NASA Langley Research Center. The main goals of the AMLS study are to provide routine, low-cost manned access to space. Technologies and system approaches have been studied that would contribute to significant reductions in operating costs relative to current systems. System and operational characteristics of the two-stage fully reusable vehicle are presented, and the various tools and methods used in the design process are summarized. The results of a series of trade studies performed to examine the effect of varying major vehicle parameters on the reference two-stage fully reusable vehicle are also summarized.

Stanley, Douglas O.↗
NASA NTRS1995

Enhanced analysis and users manual for radial-inflow turbine conceptual design code RTD

Modeling enhancements made to a radial-inflow turbine conceptual design code are documented in this report. A stator-endwall clearance-flow model was added for use with pivoting vanes. The rotor calculations were modified to account for swept blades and splitter blades. Stator and rotor trailing-edge losses and a vaneless-space loss were added to the loss model. Changes were made to the disk-friction and rotor-clearance loss calculations. The loss model was then calibrated based on experimental turbine performance. A complete description of code input and output along with sample cases are included in the report.

Glassman, Arthur J.↗
NASA NTRSDate not supplied

Investigation of Aerodynamic Matching Sensitivities for Conceptual Design

A methodology for aerodynamic matching was implemented in the Higher fidelity Conceptual Design and structural optimization (HCDstruct) tool to support transonic flutter simulations. The Enhanced Factor Correction Technique was implemented in HCDstruct to correct the Nastran doublet lattice method using data from corresponding computational fluid dynamics simulations. In this paper, sensitivities associated with this aerodynamic matching technique were investigated using HCDstruct and a Boeing 737-200-like aircraft configuration. Specifically, sensitivities of the aerodynamic matching method were investigated with respect to changes in flight conditions, such as changes in Mach number and angle of attack, and also in key design variables for the main wing, such as changes in aspect ratio and sweep angle. The variations in flight conditions and design parameters were mapped to estimated prediction error in sectional lift for the main wing, which helps to demonstrate the extent to which a user may expect a given aerodynamic correction matrix to provide suitable aerodynamic predictions for a realistic aircraft wing.

Jesse R. Quinlan↗
NASA NTRSDate not supplied

Investigation of Aerodynamic Matching Sensitivities for Conceptual Design

A methodology for aerodynamic matching was implemented in the Higher fidelity Conceptual Design and structural optimization (HCDstruct) tool to support transonic flutter simulations. The Enhanced Factor Correction Technique was implemented in HCDstruct to correct the Nastran doublet lattice method using data from corresponding computational fluid dynamics simulations. In this paper, sensitivities associated with this aerodynamic matching technique were investigated using HCDstruct and a Boeing 737-200-like aircraft configuration. Specifically, sensitivities of the aerodynamic matching method were investigated with respect to changes in flight conditions, such as changes in Mach number and angle of attack, and also in key design variables for the main wing, such as changes in aspect ratio and sweep angle. The variations in flight conditions and design parameters were mapped to estimated prediction error in sectional lift for the main wing, which helps to demonstrate the extent to which a user may expect a given aerodynamic correction matrix to provide suitable aerodynamic predictions for a realistic aircraft wing.

Jesse Ray Quinlan↗
NASA NTRS1972

Conceptual design and analysis of an infared horizon sensor with compensation for atmospheric variability

A horizon detection logic, based on a ratio-of-integrated-radiance concept, which detects the earth's horizon at a relatively stable height under all geographic and meteorological conditions was evaluated by computer simulation on a body of synthesized radiance profiles. An error-sensitivity analysis of the concept was performed, and optimum design parameter values for a sensor were determined. A conceptual design for an improved 15 micron sensor based on this analysis is discussed.

Jalink, A., Jr.↗
NASA NTRS1988

A flexible computer aid for conceptual design based on constraint propagation and component-modeling

The Rubber Airplane program, which combines two symbolic processing techniques with a component-based database of design knowledge, is proposed as a computer aid for conceptual design. Using object-oriented programming, programs are organized around the objects and behavior to be simulated, and using constraint propagation, declarative statements designate mathematical relationships among all the equation variables. It is found that the additional level of organizational structure resulting from the arrangement of the design information in terms of design components provides greater flexibility and convenience.

Kolb, Mark A.↗
NASA NTRS1974

Modular biowaste monitoring system conceptual design

The objective of the study was to define requirements and generate a conceptual design for a Modular Biowaste Monitoring System for specifically supporting shuttle life science experimental and diagnostic programs.

Fogal, G. L.↗