Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Thermal Conductivity of AM Fabricated Stainless Steel 316L Part

Thermal properties are an integral part of many diverse engineering applications, and additive manufacturing (AM), particularly laser powder bed fusion (LPBF) is shown to affect thermal properties due to the laser processing parameters. For 316L stainless steel, there is little prior research to determine the effects of the process on thermal properties. In this work, the temperature gradient is shown to create uniform, chess board-like distributions of grains in the build direction. These zones create dislocations which were visualized with EBSD techniques. Processing parameters cause hierarchal grain size distribution, with localized concentrations of small grains and large grains. Thermomechanical stresses in the rapid solidification increases dislocation density during grain formation. Previous research shows a higher density of dislocations decreases local thermal conductivity. Local and bulk thermal conductivity are shown in this work to have statistically lowered values to an average of 10-12 W/m-K compared to 14 W/m-K for conventional 316L.

36 MATERIALS SCIENCE↗

Progress in Near-Equilibrium Ammonothermal (NEAT) Growth of GaN Substrates for GaN-on-GaN Semiconductor Devices

This paper reviews the near-equilibrium ammonothermal (NEAT) growth of bulk gallium nitride (GaN) crystals and reports the evaluation of 2″ GaN substrates and 100 mmbulk GaN crystal grown in our pilot production reactor. Recent progress in oxygen reduction enabled growing NEAT GaN substrates with lower residual oxygen, coloration, and optical absorption. The oxygen concentration was approximately 2 × 1018 cm−2, and the optical absorption coefficient was 1.3 cm−1 at 450 nm. Maps of full-width half maximum (FWHM) of X-ray diffraction rocking curveswere generated for grown crystals and finished wafers. The X-ray rocking curve maps confirmed high-quality and uniform microstructure across the entire surface of the bulk crystals and substrates. The average FWHM of the 50 best bulk crystals from the recent batch was 28 ± 4 arcsec for the 002 diffraction and 34 ± 5 arcsec for the 201 diffraction, with an average radius of curvature of 20 m. X-ray topography measured on both sides of the bulk crystals implied that the density of dislocations wasreduced by one order of magnitude during the NEAT growth. A typical NEAT GaN substrate shows dislocation density of about 2 × 105 cm−2.

36 MATERIALS SCIENCE↗

A Rate Theory Model of Radiation-Induced Swelling in an Austenitic Stainless Steel

Many rate theory models of cavity (void) swelling have been published over the past 50 years, all having the same, or similar, structures. A rigorous validation of the models has not been possible because of the dearth of information concerning the microstructures that correspond with the swelling data. Whereas the lack of microstructure information is still an issue for historical swelling data, in the past 10–20 years data have been published on the evolution of the microstructure (point defect yields from collision cascades, cavity number densities, and dislocation densities/yield strengths) allowing certain gaps in information to be filled when considering historic swelling data. With reasonable estimates of key microstructure parameters, a standard rate theory model can be applied, and the model parameter space explored, in connection with historical swelling data. By using published data on: (i) yield strength as a function of dose and temperature (to establish an empirical expression for dislocation density evolution); (ii) cavity number densities as a function of temperature; and (iii) freely migrating defect (FMD) production as a function of primary knock-on atom (PKA) spectrum, the necessary parameter and microstructure inputs that were previously unknown can be used in model development. This paper describes a rate-theory model for void swelling of 316 stainless steel irradiated in the EBR-2 reactor as a function of irradiation temperature and neutron dose.

36 MATERIALS SCIENCE↗

Backstress, The Bauschinger Effect, and Cyclic Deformation

Backstresses or long range internal stresses (LRIS) in the past have been suggested by many to exist in plastically deformed crystalline materials. Elevated stresses can be present in regions of elevated dislocation density or dislocation heterogeneities in the deformed microstructures. The heterogeneities include edge dislocation dipole bundles (veins) and the edge dipole walls of persistent slip bands (PSBs) in cyclically deformed materials and cell and subgrain walls in monotonically deformed materials. The existence of long range internal stress is especially important for the understanding of cyclic deformation and also monotonic deformation. X-ray microbeam diffraction experiments performed by the authors using synchrotron x-ray microbeams determined the elastic strains within the cell interiors. The studies were performed using, oriented, monotonically deformed Cu single crystals. The results demonstrate that small long-range internal stresses are present in cell interiors. These LRIS vary substantially from cell to cell as 0% to 50% of the applied stress. The results are related to the Bauschinger effect, often explained in terms of LRIS.

36 MATERIALS SCIENCE↗

Backstress, the Bauschinger Effect and Cyclic Deformation

Backstresses or long range internal stresses (LRIS) in the past have been suggested by many to exist in plastically deformed crystalline materials. Elevated stresses can be present in regions of elevated dislocation density or dislocation heterogeneities in the deformed microstructures. The heterogeneities include edge dislocation dipole bundles (veins) and the edge dipole walls of persistent slip bands (PSBs) in cyclically deformed materials and cell and subgrain walls in monotonically deformed materials. The existence of long range internal stress is especially important for the understanding of cyclic deformation and also monotonic deformation. X-ray microbeam diffraction experiments performed by the authors using synchrotron x-ray microbeams determined the elastic strains within the cell interiors. The studies were performed using, oriented, monotonically deformed Cu single crystals. The results demonstrate that small long-range internal stresses are present in cell interiors. These LRIS vary substantially from cell to cell as 0 % to 50 % of the applied stress. The results are related to the Bauschinger effect, often explained in terms of LRIS.

36 MATERIALS SCIENCE↗

Microstructural changes in Beta-silicon nitride grains upon crystallizing the grain-boundary glass

Crystallizing the grain boundary glass of a liquid phase sintered Si3N4 ceramic for 2 h or less at 1500 C led to formation of gamma Y2Si2O7. After 5 h at 1500 C, the gamma Y2Si2O7 had transformed to beta Y2Si2O7 with a concurrent dramatic increase in dislocation density within beta Si3N4 grains. Reasons for the increased dislocation density is discussed. Annealing for 20 h at 1500 C reduced dislocation densities to the levels found in as-sintered materials.

Lee, William E.↗

Prediction of dislocation generation during Bridgman growth of GaAs crystals

Dislocation densities are generated in GaAs single crystals due to the excessive thermal stresses induced by temperature variations during growth. A viscoplastic material model for GaAs, which takes into account the movement and multiplication of dislocations in the plastic deformation, is developed according to Haasen's theory. The dislocation density is expressed as an internal state variable in this dynamic viscoplastic model. The deformation process is a nonlinear function of stress, strain rate, dislocation density and temperature. The dislocation density in the GaAs crystal during vertical Bridgman growth is calculated using a nonlinear finite element model. The dislocation multiplication in GaAs crystals for several temperature fields obtained from thermal modeling of both the GTE GaAs experimental data and artificially designed data are investigated.

Tsai, C. T.↗

In-situ synchrotron X-ray study of microstructural evolution during creep deformation in Grade 91 steel

Here, creep deformation mechanism of Grade 91 steel at 650 °C was investigated in-situ via wide-angle X-ray scattering (WAXS). WAXS peak broadening and a modified Williamson-Hall analysis provided information on evolution of dislocation densities in the primary α–Fe phase, while WAXS peak shifts provided lattice strains in the α–Fe matrix, M 23 C 6 and MX precipitates. Load transfer was not evident during in-situ creep deformation, suggesting that precipitates did not significantly strengthen the matrix during creep deformation. Peak broadening results illustrated an increase in average dislocation density during primary stage creep. After onset of secondary creep, there was a decrease in dislocation density, attributed to annihilation and re-ordering of dislocations in the subgrain structure, followed by a relatively constant average dislocation density with increasing strain.

36 MATERIALS SCIENCE↗

In Situ TEM Investigation of ZnO Nanowires during Sodiation and Lithiation Cycling

The development of sodium-ion batteries has drawn lots of attention recently due to the low-cost and eco-friendly sodium source. However, a fundamental understanding of the sodiation behavior for commonly used electrode materials is still limited. Here, combining in situ transmission electron microscopy, aberration-corrected scanning transmission electron microscopy, and ex situ battery cycling tests, the lithiation and sodiation behavior of ZnO nanowires is investigated. The findings show a direct correlation between the mechanical behavior of the lithiated/sodiated ZnO nanowires and their electrochemical cyclability. The mechanical brittleness of LiZn and the formation of nanocracks lead to the poor cyclability of Li-ion batteries with a ZnO anode. However, the sodiated ZnO nanowires show profuse dislocation plasticity. The observed high-density dislocations offer the sodiated ZnO anode more ductility and subsequently better cyclability than its Li-ion counterpart. The results reveal the importance of understanding the correlation between mechanical properties of battery electrodes and their cycling abilities.

Asayesh-Ardakani, Hasti↗

Theoretical Investigation of Microstructure Evolution and Deformation of Zirconium Under Cascade Damage Conditions

This work is based on our reaction-diffusion model of radiation growth of Zr-based materials proposed recently in "On the Origin of Radiation Growth of HCP Crystals". In "On the Origin of Radiation Growth of HCP Crystals", the equations for the strain rates in unloaded pure crystal under cascade damage conditions of, e.g., neutron or heavy-ion irradiation were derived as functions of dislocation densities, which include contributions from dislocation loops, and spatial distribution of their Burgers vectors. The model takes into account the intra-cascade clustering of self-interstitial atoms and their one-dimensional diffusion; explains the growth stages, including the break-away growth of pre-annealed samples; and accounts for some striking observations, such as of negative strain in prismatic direction, and co-existence of vacancy- and interstitial-type prismatic loops. In this report, the change of dislocation densities due to accumulation of sessile dislocation loops is taken into account explicitly to investigate the dose dependence of radiation growth. The dose dependence of climb rates of dislocations is calculated, which is important for the climb-induced glide model of radiation creep. The results of fitting the model to available experimental data and some numerical calculations of the strain behavior of Zr for different initial dislocation structures are presented and discussed. The computer code RIMD-ZR.V1 (Radiation Induced Microstructure and Deformation of Zr) developed is described and attached to this report.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Dislocation and Structural Studies at Metal–Metallic Glass Interface at Low Temperature

In this paper, molecular dynamics (MD) simulation deformation studies on the Al (metal)–Cu{sub 50}Zr{sub 50} (metallic glass) model interface is carried out based on cohesive zone model. The interface is subjected to mode-I loading at a strain rate of 10{sup 9} s{sup −1} and temperature of 100 K. The dislocations reactions and evolution of dislocation densities during the deformation have been investigated. Atomic interactions between Al, Cu and Zr atoms are modeled using EAM (embedded atom method) potential, and a timestep of 0.002 ps is used for performing the MD simulations. A circular crack and rectangular notch are introduced at the interface to investigate the effect on the deformation behavior and fracture. Further, scale size effect is also investigated. The structural changes and evolution of dislocation density are also examined. It is found that the dominant deformation mechanism is by Shockley partial dislocation nucleation. Amorphization is observed in the Al regions close to the interface and occurs at a lower strain in the presence of a crack. The total dislocation density is found to be maximum after the first yield in both the perfect and defect interface models and is highest in the case of perfect interface with a density of 6.31 × 10{sup 17} m{sup −2}. In the perfect and circular crack defect interface models, it is observed that the fraction of Shockley partial dislocation density decreases, whereas that of strain rod dislocations increases with increase in strain.

36 MATERIALS SCIENCE↗

Investigating Influential Parameters for High-Purity Germanium Crystal Growth

This paper focuses on the research and development of high-purity germanium (HPGe) crystals for detector fabrication, specifically targeting applications in rare-event physics searches. The primary objective was to produce large-scale germanium crystals weighing >1 kg with a controlled diameter of ∼10 cm and an impurity range of approximately 1010/cm 3. Ensuring structural integrity and excellent crystalline quality requires a thorough assessment of dislocation density, a critical aspect of the crystal development process. Dislocation density measurements play a crucial role in maximizing the sensitivity of HPGe detectors, and our findings confirmed that the dislocation density fell within acceptable ranges for detector fabrication. Additionally, this paper examines the segregation coefficient of various contaminants during the crystal development process. Comprehensive analysis of impurity segregation is essential for reducing contaminant quantities in the crystal lattice and customizing purification processes. This, in turn, minimizes undesired background noise, enhancing signal-to-noise ratios for rare-event physics searches and overall detector performance. The investigation included the segregation coefficients of three major acceptors and one donor in crystals grown at the University of South Dakota, providing valuable insights for optimizing crystal purity and detector efficiency.

Bhattarai, Sanjay↗

Microstructural changes in beta-silicon nitride grains upon crystallizing the grain-boundary glass

Crystallizing the grain-boundary glass of a liquid-phase-sintered Si3N4 ceramic for 2 h or less at 1500 C led to formation of delta-Y2Si2O7. After 5 h at 1500 C, the delta-Y2Si2O7 had transformed to beta-Y2Si2O7 with a concurrent dramatic increase in dislocation density within beta-Si3N4 grains. Reasons for the increased dislocation density are discussed. Annealing for 20 h at 1500 C reduced dislocation densities to the levels found in as-sintered material.

Lee, William E.↗

The critical role of growth temperature on the structural and electrical properties of AlGaN/GaN high electron mobility transistor heterostructures grown on Si(111)

This work is dedicated to the study of the growth by ammonia source molecular beam epitaxy of Al{sub x}Ga{sub 1-x}N/GaN high electron mobility transistors on (111) oriented silicon substrates. The effect of growth conditions on the structural and electrical properties of the heterostructures was investigated. It is shown that even a slight variation in the growth temperature of the thick GaN buffer on AlN/GaN stress mitigating layers has a drastic influence on these properties via a counterintuitive effect on the dislocation density. Both in situ curvature measurements and ex situ transmission electron microscopy and x-ray diffraction experiments indicate that the relaxation rate of the lattice mismatch stress increases with the growth temperature but finally results in a higher dislocations density. Furthermore, a general trend appears between the final wafer curvature at room temperature and the threading dislocation density. Finally, the influence of the dislocation density on the GaN buffer insulating properties and the two-dimensional electron gas transport properties at the Al{sub x}Ga{sub 1-x}N/GaN interface is discussed.

36 MATERIALS SCIENCE↗

Dislocation-related trap levels in nitride-based light emitting diodes

Deep level transient spectroscopy was performed on InGaN/GaN multiple quantum well light emitting diodes (LEDs) in order to determine the effect of the dislocation density on the deep intragap electronic levels. The LEDs were grown by metalorganic vapor phase epitaxy on GaN templates with a high dislocation density of 8 × 10{sup 9} cm{sup −2} and a low dislocation density of 3 × 10{sup 8} cm{sup −2}. Three trapping levels for electrons were revealed, named A, A1, and B, with energies E{sub A} ≈ 0.04 eV, E{sub A1} ≈ 0.13 eV, and E{sub B} ≈ 0.54 eV, respectively. The trapping level A has a much higher concentration in the LEDs grown on the template with a high density of dislocations. The logarithmic dependence of the peak amplitude on the bias pulse width for traps A and A1 identifies the defects responsible for these traps as associated with linearly arranged defects. We conclude that traps A and A1 are dislocation-related intragap energy levels.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructural Evolution of Tantalum During Deformation and Subsequent Annealing

Microstructure-aware models are necessary to predict the behavior of material based on process knowledge or to extrapolate mechanical properties of materials to environmental conditions which are not easily reproduced in the laboratory, e.g., nuclear reactor environments. Elemental Ta provides a relatively simple BCC system in which to develop a microstructural understanding of deformation processes which can then be applied to more complicated BCC alloys. In situ neutron diffraction during compressive deformation and subsequent heat treatment have been used to monitor the evolution of microstructural features in Ta throughout simulated processing steps. Crystallographic texture and dislocation density are determined as a function of first plastic strain, then temperature. Lattice strains are determined and attributed to stresses at macroscopic, grain and dislocation length scales. The increase of the dislocation density through deformation and subsequent recovery during heat treatment is monitored through the changing diffraction line profile. Also, randomization of the texture is used as a signature of recrystallization. The recovery of dislocations through annihilation is not observed to depend on the initial dislocation density in the range studied here. In contrast, recrystallization is observed to depend strongly on the initially dislocation density.

36 MATERIALS SCIENCE↗

Effect of Hot Rolling on the Microstructure and Mechanical Properties of Nitrogen Alloyed Austenitic Stainless Steel

In the present investigation, the effect of multi-pass hot rolling in the temperature range of 700–1000 °C on the microstructure and mechanical properties of nitrogen alloyed austenitic stainless steel was studied with the aid of optical microscopy, tensile testing and x-ray diffraction measurements. The microstructural changes that occurred in the hot rolled specimens were elongation of grains in rolling direction, nucleation of new grains at the grain boundaries of elongated grains and growth of nucleated grains to form fully recrystallized grains. Elongated grains formed at lower rolling temperature (700–800 °C) due to inadequate strain/temperature for the initiation of dynamic recrystallization. At higher rolling temperature (900–1000 °C), fine grains formed due to dynamic recrystallization. Tensile properties showed strong dependency on the rolling temperature. Tensile strength increased with the decrease in the rolling temperature at the cost of ductility. Maximum strength was observed in samples hot rolled at 700 °C with yield strength of 917 MPa and ductility of 25%. This variation in the tensile properties with the rolling temperature is attributed to changes in the dislocation density and grain structure. The estimated yield strength from the dislocation density, solid solution and grain boundary strengthening closely matched with experimentally determined yield strength confirming the role of dislocation density and grain size in the strengthening.

36 MATERIALS SCIENCE↗

Cellular Automaton Modeling of Dynamic Recrystallization of Nimonic 80A Superalloy Based on Inhomogeneous Distribution of Dislocations Inside Grains

A modified cellular automaton (CA) model in the time and space scale is developed to simulate the dynamic recrystallization (DRX) mechanism of Nimonic 80A nickel-base superalloy during hot deformation. Some necessary thermo-mechanical parameters used as input data in CA approach such as work hardening and softening coefficient are fitted according to the previous hot compression experiments. Based on the experimental results, nucleation kinetics is modified as a function of Zener-Holloman parameter. A dislocation density model at transient recrystallization boundary is proposed, in which the dislocation density is a function of temperature, strain rate and annealed dislocation density. The simulated results are in good agreement with experimental results, proving that the modified CA model is capable of predicting both flow behavior and microstructural evolution of Nimonic 80A during hot deformation. According to the experimental and simulated results, the DRX behavior is discussed in detail. It demonstrates that the flow stress and microstructural evolution of DRX have a relationship with the deformation temperature and strain rate.

36 MATERIALS SCIENCE↗