Search NASA⌕ Search

SEARCH · Search NASA

Results for “distributed surface roughness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

On the Distribution and Implications of Mantled and Exhumed Terrains on Mars

The intent of this paper is to show the relationships for Mars among albedo, thermal inertia, roughness inferred from MOLA pulse width spread data, and geology inferred from photogeological analyses. Mapping of surface units using these parameters and approaches, in combination with analysis of hyperspectral image data from ISM, TES, OMEGA, and CRISM observations, will maximize our understanding of the distribution and nature of surface units on the red planet. Results will directly impact the selection of landing sites that exhibit geological records needed to understand planetary habitability.

Arvidson, R. E.↗

Experimental aerodynamic characteristics of an NACA 0012 airfoil with simulated glaze ice

The effect of a simulated glaze-ice accretion on the aerodynamic performance of a NACA 0012 airfoil was studied experimentally. Two ice shapes were tested: one from an experimentally measured accretion, and one from an accretion predicted using a computer model given the same icing conditions. Lift, drag, and pitching moment were measured for the airfoil with both smooth and rough ice shapes. The ice shapes caused large lift and drag penalties, primarily due to large separation bubbles. Surface pressure distributions clearly showed the regions of separated flow. The aerodynamic performance of the two shapes compared well at positive, but not negative, angles of attack.

Bragg, M. B.↗

Comparison of Convective Heat Transfer Correlations and Their Application to Nuclear Thermal Propulsion Reactors

This study analyzes various Nusselt number and friction factor correlations and applies them to a Small Nuclear Rocket Engine model with a Sinusoidal power distribution profile to understand their effects on the temperatures and pressures inside the reactor. A nodal thermal hydraulic solver was used to determine the fluid and channel surface temperatures while also incorporating variable fluid properties and channel roughness. The results showed that the considered friction factors could essentially be used interchangeably given that their difference affected the pressure by less than 1%. However, large variations in the tube surface temperature were obtained for the different Nusselt numbers while the fluid temperature distribution was forced to remain the same. Supersonic flow conditions presented by Maynard Taylor are investigated to serve as a baseline for how experimental errors can lead to uncertainties in the reported empirical correlations. Detailed experimental investigation is necessary to determine the Nusselt number correlation that will provide the best prediction of the thermal hydraulic performance inside the reactor fluid flow channels.

Experiment↗

Comparison of Convective Heat Transfer Correlations and Their Application to NTP Reactors

This study analyzes various Nusselt number and friction factor correlations and applies them to a Small Nuclear Rocket Engine model with a Sinusoidal power distribution profile to understand their effects on the temperatures and pressures inside the reactor. A nodal thermal hydraulic solver was used to determine the fluid and channel surface temperatures while also incorporating variable fluid properties and channel roughness. The results showed that the considered friction factors could essentially be used interchangeably given that their difference affected the pressure by less than 1%. However, large variations in the tube surface temperature were obtained for the different Nusselt numbers while the fluid temperature distribution was forced to remain the same. Supersonic flow conditions presented by Maynard Taylor are investigated to serve as a baseline for how experimental errors can lead to uncertainties in the reported empirical correlations. Detailed experimental investigation is necessary to determine the Nusselt number correlation that will provide the best prediction of the thermal hydraulic performance inside the reactor fluid flow channels.

Nuclear Thermal Propulsion↗

Rotational modulation and flares on RS Canum Venaticorum and BY Draconis-type stars. XIV - Phase, eclipse and flare observations of YY Geminorum by Exosat and IUE

The eclipsing spectroscopic binary YY Geminorum has been observed at optical, ultraviolet, and X-ray wavelengths for rotational modulation, eclipse variability, and flaring. The epoch T(phi = 0) = JD 2425698.3561, and the phase P = 0.81428224 d. The quiescent level of Mg II emission is remarkably steady during the three-year observing interval, with F(Mg II) roughly 3.6 x 10 to the -12th erg/sq cm/s. Both stars appear to have identical Mg II surface fluxes, with F roughly 1.8 x 10 to the 6th erg/sq cm/s. Both stars appear to be covered with evenly distributed Mg II emitting regions consistent with the proposition of Doyle (1987) that saturation of the Mg II lines occurs for stars having P less than 4 d, implying that such stars are entirely covered by plage. The transition region lines show significantly more rotational modulation and/or secular variability than Mg II. Both Mg II and the transition region lines show preflare and postflare enhancement.

Haisch, B. M.↗

Long Duration Exposure Facility (LDEF) experiment M0003 meteoroid and debris survey

A survey of the meteoroid and space debris impacts on LDEF experiment M0003 was performed. The purpose of this survey was to document significant impact phenomenology and to obtain impact crater data for comparison to current space debris and micrometeoroid models. The survey consists of the following: photomicrographs of significant impacts in a variety of material types; accurate measurements of impact crater coordinates and dimensions for selected experiment surfaces; and databasing of the crater data for reduction, manipulation, and comparison to models. Large area surfaces that were studied include the experiment power and data system (EPDS) sunshields, environment exposure control canister (EECC) sunshields, and the M0003 signal conditioning unit (SCU) covers. Crater diameters down to 25 microns were measured and cataloged. Both leading (D8) and trailing (D4) edge surfaces were studied and compared. The EPDS sunshields are aluminum panels painted with Chemglaze A-276 white thermal control paint, the EECC sunshields are chromic acid-anodized aluminum, and the SCU covers are aluminum painted with S13GLO white thermal control paint. Typical materials that have documented impacts are metals, glasses and ceramics, composites, polymers, electronic materials, and paints. The results of this survey demonstrate the different response of materials to hypervelocity impacts. Comparison of the survey data to curves derived from the Kessler debris model and the Cour-Palais micrometeoroid model indicates that these models overpredict small impacts (less than 100 micron) and may underpredict large impacts (greater than 1000 micron) while having fair to good agreement for the intermediate impacts. Comparison of the impact distributions among the various surfaces indicates significant variations, which may be a function of material response effects, or in some cases surface roughness. Representative photographs and summary graphs of the impact data are presented.

Meshishnek, M. J.↗

Interpretation of planetary radar observations - The relationship between actual and inferred slope distributions

We examined the distribution of surface slopes of a variety of terrestrial surfaces by field measurement, representing surfaces formed by a wide range of processes, and compared the results to planetary radar data. Slope distributions of the measured surfaces differed considerably from the distributions assumed by accepted models of radar scattering. We also used Hagfors' model of radar scattering to predict the return that would be expected from surfaces where two discrete surface types were present within the radar field of view and found that the shapes of the resulting slope distributions differed from those predicted by the Hagfors model for homogeneous surfaces. Together, these results suggest that current methods of determining surface roughness from radar may significantly underestimate the roughness of planetary surfaces and that the derived rms slope can best be used as a qualitative guide to the physical interpretation of actual surface properties.

Mccollom, Thomas M.↗

Geomorphic Processes and Remote Sensing Signatures of Alluvial Fans in the Kun Lun Mountains, China

The timing of alluvial deposition in arid and semiarid areas is tied to land-surface instability caused by regional climate changes. The distribution pattern of dated deposits provides maps of regional land-surface response to past climate change. Sensitivity to differences in surface roughness and composition makes remote sensing techniques useful for regional mapping of alluvial deposits. Radar images from the Spaceborne Radar Laboratory and visible wavelength images from the French SPOT satellite were used to determine remote sensing signatures of alluvial fan units for an area in the Kun Lun Mountains of northwestern China. These data were combined with field observations to compare surface processes and their effects on remote sensing signatures in northwestern China and the southwestern United States. Geomorphic processes affecting alluvial fans in the two areas include aeolian deposition, desert varnish, and fluvial dissection. However, salt weathering is a much more important process in the Kun Lun than in the southwestern United States. This slows the formation of desert varnish and prevents desert pavement from forming. Thus the Kun Lun signatures are characteristic of the dominance of salt weathering, while signatures from the southwestern United States are characteristic of the dominance of desert varnish and pavement processes. Remote sensing signatures are consistent enough in these two regions to be used for mapping fan units over large areas.

Farr, Tom G.↗

Evidence for Surface and Subsurface Ice Inside Micro Cold-Traps on Mercury's North Pole

The small obliquity of Mercury causes topographic depressions located near its poles to cast persistent shadows. Many [1, 9, 15] have shown these permanently shadowed regions (PSRs) may trap water ice for geologic time periods inside cold-traps. More recently, direct evidence for the presence of water ice deposits inside craters was remotely sensed in RADAR [5] and visible imagery [3]. Albedo measurements (reflectence at 1064 nm) obtained by the MErcury Space ENviroment GEochemistry and Ranging Laser Altimeter (MLA) found unusually bright and dark areas next to Mercury's north pole [7]. Using a thermal illumination model, Paige et al. [8] found the bright deposits are correlated with surface cold-traps, and the dark deposits are correlated with subsurface cold-traps. They suggested these anomalous deposits were brought to the surface by comets and were processed by the magnetospheric radiation flux, removing hydrogen and mixing C-N-O-S atoms to form a variety of molecules which will darken with time. Here we use a thermal illumination model to find the link between the cold-trap area fraction of a rough surface and its albedo. Using this link and the measurements obtained by MESSENGER we derive a surface and a subsurface ice distribution map on Mercury's north pole below the MESSENGER spatial resolution, approximately 500 m. We find a large fraction of the polar ice on Mercury resides inside micro cold-traps (of scales 10 - 100 m) distributed along the inter-crater terrain.

Laser Altimeter↗

Pinacate-gran Desierto Region, Mexico: SIR-A Data Analysis

Radar images (SIR-A) from the Columbia space shuttle were used to assess the radar returns of terrain shaped by volcanic, aeolian, and fluvial processes in northwest Sonora. Field studies and photointerpretation show that sand dunes are poorly imaged by SIR-A, in contrast to SEASAT, evidently a consequence of the greater SIR-A incidence angle; star dunes are visible only as small bright spots representing merging arms at dune apices which may act as corner reflectors. Desert grasses and bushes (approx. 2 m high) have little effect on radar brightness. Only larger trees with woody trunks approx. 0.5 m across are effective radar reflectors; their presence contributes to radar bright zones along some arroyos. The radar brightness of lava flows decreases with surface roughness and presence of mantling windblown sediments and weathering products; however, old uplifted (faulted) flows are of equal brightness to fresh, unmantled aa flows. Maar craters display circular patterns of varying radar brightness which represent a combination of geometry, slope, and distribution of surface materials. Some radar bright rings in the Pinacates resemble craters on radar but are observed to be playas encircled by trees.

Christensen, P.↗

The azimuthal and radial distributions of HI and H2 in NGC 6946

A study was completed of the atomic and molecular components of the ISM in NGC 6946. The distribution of molecular clouds was determined from a fully sampled CO map of the inner disk using the 14-meter telescope of the FCRAO. The distribution of atomic gas was derived from VLA observations at 40" resolution in the D configuration. When comparing the global CO and HI properties with other components of the galaxy, it was found that the azimuthally averaged radial distributions of CO, H-alpha, radio continuum and blue light all exhibit similar roughly exponential falloffs, while the azimuthally averaged HI surface densities vary by only a factor of 2 out to R = 16 kpc. This indicates that while the H-alpha/CO ratio is approximately constant with radius, the CO/HI ratio decreases by a factor of 30 from the center of the galaxy to R = 10 kpc.

Tacconi-Garman, Linda J.↗

Measurements of noise produced by flow past lifting surfaces

Wind tunnel studies have been conducted to determine the specific locations of aerodynamic noise production within the flow field about various lifting-surface configurations. The models tested included low aspect ratio shapes intended to represent aircraft flaps, a finite aspect ratio NACA 0012 wing, and a multi-element wing section consisting of a main section, a leading edge flap, and dual trailing edge flaps. Turbulence was induced on the models by surface roughness. Lift and drag were measured for the flap models. Hot-wire anemometry was used for study of the flap-model vortex roll-up. Apparent noise source distributions were measured by use of a directional microphone system, located outside the tunnel, which was scanned about the flow region to be analyzed under computer control. These distributions exhibited a diversity of pattern, suggesting that several flow processes are important to lifting-surface noise production. Speculation concerning these processes is offered.

Kendall, J. M.↗

On the design of airfoils in which the transition of the boundary layer is delayed

A method is presented for designing suitable thickness distributions and mean camber lines for airfoils permitting extensive chordwise laminar flow. Wind tunnel and flight tests confirming the existence of laminar flow; possible maintenance of laminar flow by area suction; and the effects of wind tunnel turbulence and surface roughness on the promotion of premature boundary layer transition are discussed. In addition, estimates of profile drag and scale effect on maximum lift of the derived airfoils are made.

BOUNDARY LAYER CONTROL - AIRFOILS↗

Multigrid methods for flow transition in three-dimensional boundary layers with surface roughness

The efficient multilevel adaptive method has been successfully applied to perform direct numerical simulations (DNS) of flow transition in 3-D channels and 3-D boundary layers with 2-D and 3-D isolated and distributed roughness in a curvilinear coordinate system. A fourth-order finite difference technique on stretched and staggered grids, a fully-implicit time marching scheme, a semi-coarsening multigrid method associated with line distributive relaxation scheme, and an improved outflow boundary-condition treatment, which needs only a very short buffer domain to damp all order-one wave reflections, are developed. These approaches make the multigrid DNS code very accurate and efficient. This allows us not only to be able to do spatial DNS for the 3-D channel and flat plate at low computational costs, but also to do spatial DNS for transition in the 3-D boundary layer with 3-D single and multiple roughness elements, which would have extremely high computational costs with conventional methods. Numerical results show good agreement with the linear stability theory, the secondary instability theory, and a number of laboratory experiments. The contribution of isolated and distributed roughness to transition is analyzed.

Liu, Chaoqun↗

Variation in Velocity Profile with Change in Surface Roughness of Boundary

The present report deals with the variation of a turbulent velocity profile in flow from rough to smooth wall and vice versa. Expressions obtained for the shear-stress distribution with respect to the distance from the point of junction of the different roughnesses and from the wall distance, are utilized to ascertain the developing velocity distributions. Under simplified assumptions, the use of these formulas renders possible the integration of the motion equations for the shear stress. This calculation is carried out and compared with the experiments.

Jacobs, W↗

Sensor Data Distribution With Robustness and Reliability: Toward Distributed Components Model

In planetary surface exploration mission, sensor data distribution is required in many aspects, for example, in navigation, scheduling, planning, monitoring, diagnostics, and automation of the field tasks. The challenge is to distribute such data in the robust and reliable way so that we can minimize the errors caused by miscalculations, and misjudgments that based on the error data input in the mission. The ad-hoc wireless network on planetary surface is not constantly connected because of the nature of the rough terrain and lack of permanent establishments on the surface. There are some disconnected moments that the computation nodes will re-associate with different repeaters or access points until connections are reestablished. Such a nature requires our sensor data distribution software robust and reliable with ability to tolerant disconnected moments. This paper presents a distributed components model as a framework to accomplish such tasks. The software is written in Java and utilized the available Java Message Services schema and the Boss implementation. The results of field experimentations show that the model is very effective in completing the tasks.

Alena, Richard L.↗

Radar polarimetry for geoscience applications

The present volume on radar polarimetry for geoscience applications discusses wave properties and polarization, scattering matrix representation for simple targets, scattering models for point and distributed targets, polarimetric scatterometer systems and measurements, polarimetric radar system design, and polarimetric SAR applications. Attention is given to plane waves in a lossless homogeneous medium-wave polarization, polarization synthesis and response, and coordinate system transformations. Topics addressed include high- and low-frequency scattering, rough-surface scattering models, radiative transfer theory and deficiencies thereof, solutions for the radiative transfer equation, and a radiative transfer model for a forest canopy. Also discussed are network analyzer-based polarimetric scatterometers, calibration of polarimetric scatterometers, synthesized polarization response of distributed targets, and measurement of the propagation parameters of a forest canopy.

Ulaby, Fawwaz T.↗

Radar altimeter mean return waveforms from near-normal-incidence ocean surface scattering

Under assumptions common in radar altimetry, the mean backscattered return power for a short-pulse radar and near-normal-incidence scattering from a rough ocean surface is given by the convolution of several terms. For a nearly Gaussian transmitted pulse shape scattered from a nearly Gaussian distributed sea surface, a small-argument series expansion of one of the terms within the convolution leads to a several-term power series expansion for the mean return waveform. Specific expressions are given for the first four terms. These results, which require much less computer time than would the otherwise necessary numerical convolution, are useful for data analysis from current or past radar altimeters and for design studies of future systems. Several representative results are presented for an idealized Seasat radar altimeter.

Hayne, G. S.↗