Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamic experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Improving manganin gauge measurements near radiographic fiducials

In dynamic experiments diagnosed with radiography and stress gauges, the gauges are often placed adjacent to radio-graphic fiducials, such as Ta foil, which perturbs the stress measurement. We conducted experiments to test the performance of different arrangements of manganin stress gauges and Ta foils. Three different gauge/foil configurations were tested, as well as a solitary gauge as control. Gauge/foil layers were placed between high-density polyethylene (HDPE) discs and impacted by a projectile in a gas gun, a simplification of a dynamic, high explosive experiment configuration. The stress measurements were minimally perturbed when a section of foil was removed near the active element of the gauge, as expected. In conclusion, a follow-up experiment showed that the modification to the foil has minimal impact on the radiographic measurement of the dynamic flow.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1997

The Upper Atmosphere Research Satellite In-Flight Dynamics

Upper Atmosphere Research Satellite flight data from the first 737 days after launch (September 1991) was used to investigate spacecraft disturbances and responses. The investigation included two in-flight dynamics experiments (approximately three orbits each). Orbital and configuration influences on spacecraft dynamic response were also examined. Orbital influences were due to temperature variation from crossing the Earth's terminator and variation of the solar incident energy as the orbit precessed. During the terminator crossing, the rapid ambient temperature change caused the spacecraft's two flexible appendages to experience thermal elastic bending (thermal snap). The resulting response was dependent upon the orientation of the solar array and the solar incident energy. Orbital influences were also caused by on-board and environmental disturbances and spacecraft configuration changes resulting in dynamic responses which were repeated each orbit. Configuration influences were due to solar array rotation changing spacecraft modal properties. The investigation quantified the spacecraft dynamic response produced by the solar array and high gain antenna harmonic drive disturbances. The solar array's harmonic drive output resonated two solar array modes. Friction in the solar array gear drive provided sufficient energy dissipation which prevented the solar panels from resonating catastrophically; however, the solar array vibration amplitude was excessively large. The resulting vibration had a latitude-specific pattern.

Woodard, Stanley E.↗
NASA NTRS1988

In-reach and out-reach programs

Information is given in viewgraph form on in-reach and out-reach programs in in-space technology experiments. Information is given on thermal energy storage materials technology, industry/university in-space technology experiments, heat pipe performance, working fluid behavior, a tank pressure control experiment, spacecraft glow, the Mid-Deck Zero-Gravity Dynamics Experiment, and emulsion chamber technology.

Pyle, Jon S.↗
NASA NTRS1990

The MODE family of on-orbit experiments: The Middeck Active Control Experiment (MACE)

A flight experiment entitled the Middeck Active Control Experiment (MACE), proposed by the Space Engineering Research Center (SERC) at the Massachusetts Institute of Technology, is described. This is the second in a family of flight experiments being developed at MIT. The first is the Middeck 0-Gravity Dynamics Experiment (MODE) which investigates the nonlinear behavior of contained fluids and truss structures in zero gravity. The objective of the MACE program is to investigate and validate the modeling of the dynamics of an actively controlled flexible, articulating, multibody platform free floating in zero gravity. A rationale and experimental approach for the program are presented. The rationale shows that on-orbit testing, coupled with ground testing and a strong analytical program, is necessary in order to fully understand both how flexibility of the platform affects the pointing problem, as well as how gravity perturbs this structural flexibility causing deviations between 1- and 0-gravity behavior. The experimental approach captures the essential physics of multibody platforms, by identifying the appropriate attributes, tests, and performance metrics of the test article and defines the tests required to successfully validate the analytical framework.

Crawley, Edward F.↗
NASA NTRS2000

Characterization of Microgravity Environment on Mir

This paper presents the microgravity analysis results using dynamic response data collected during the first phase of the Mir Structural Dynamics Experiment (MiSDE). Although MiSDE was designed and performed to verify structural dynamic models, it also provided information for determining microgravity characteristics of the structure. This study analyzed ambient responses acquired during orbital day-to-night and night-to-day transitions, crew treadmill and ergometer exercises, and intentional crew activities. Acceleration levels for one-third octave bands were calculated to characterize the microgravity environment of the station. Spectrograms were also used to analyze the time transient nature of the responses. Detailed theoretical background and analysis results will also be included in the final draft.

Kim, Hyoung↗
DOE OSTI2017

Role of Cations in CO 2 Adsorption, Dynamics, and Hydration in Smectite Clays under in Situ Supercritical CO 2 Conditions

This paper explores the molecular-scale interactions between CO 2 and the representative smectite mineral hectorite under supercritical conditions (90 bar, 50°C) using novel in situ X-ray diffraction (XRD), infrared (IR) spectroscopy, and magic angle spinning (MAS) nuclear magnetic resonance (NMR) techniques. Particular emphasis is placed on understanding the roles of the smectite charge balancing cation (CBC) and H O in these interactions. The data show that supercritical CO 2 (scCO 2 ) can be adsorbed on external surfaces and in the confined interlayer spaces of hectorite at 50°C and 90 bar, with the uptake of CO 2 into the interlayer favored at low H 2 O content and when the basal spacing is similar to a monolayer hydrate of hectorite (1WL, ~12.5 Å). These results are in agreement with published spectroscopic and molecular modeling data for the related smectite Na-montmorillonite.Charge balancing cations with small radii, large hydration energies, and low polarizabilities tend to scavenge H 2 O from humid scCO 2 or retain the H 2 O they held before scCO 2 exposure, swelling spontaneously to a bilayer hydrate (2WL) dominated state that largely prevents CO 2 -ion interactions and influences the extent of CO 2 intercalation into the interlayer. In contrast, ions with large radii, low hydration energies, and large polarizabilities more readily form close associations with CO 2 with the energetics enabling coexistence of CO 2 and H2O in the interlayer over a wide range of scCO 2 humidities. Integrating our results with those from molecular dynamics simulations of wet CO 2 -bearing montmorillonites suggest that adsorbed CO 2 in 1WL-type interlayers is oriented with its long axis parallel to the clay sheets and experiences dynamics dominated by anisotropic rotation about the axis perpendicular to the CO 2 long axis at rates of at least ~105 Hz. If appreciable CO 2 is adsorbed in 2WL-type interlayers, it must experience a mean orientation and dynamic averaging affects that mimic the 1WL-type adsorption environment. External surface adsorbed CO 2 is dynamically similar to the 1WL case, but the CO 2 long axis samples a larger range of orientations with respect to the smectite surface and adopts a different mean angle between the long axis and the smectite surface. Our data also suggest that equilibrating hectorite with a largevolume of scCO 2 at 50°C and 90 bar leads to interlayer dehydration, with the extent of dehydration correlating with the hydrophilicity of the CBC.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1984

Alternative experiments using the geophysical fluid flow cell

This study addresses the possibility of doing large scale dynamics experiments using the Geophysical Fluid Flow Cell. In particular, cases where the forcing generates a statically stable stratification almost everywhere in the spherical shell are evaluated. This situation is typical of the Earth's atmosphere and oceans. By calculating the strongest meridional circulation expected in the spacelab experiments, and testing its stability using quasi-geostrophic stability theory, it is shown that strongly nonlinear baroclinic waves on a zonally symmetric modified thermal wind will not occur. The Geophysical Fluid Flow Cell does not have a deep enough fluid layer to permit useful studies of large scale planetary wave processes arising from instability. It is argued, however, that by introducing suitable meridional barriers, a significant contribution to the understanding of the oceanic thermocline problem could be made.

Hart, J. E.↗
DOE OSTI2024

Dynamical instability in multi-orbiter systems with gas friction

ABSTRACT Closely packed multiplanet systems are known to experience dynamical instability if the spacings between the planets are too small. Such instability can be tempered by the frictional forces acting on the planets from gaseous discs. A similar situation applies to stellar-mass black holes embedded in active galactic nuclei discs around supermassive black holes. We use N-body integrations to evaluate how the frictional damping of orbital eccentricity affects the growth of dynamical instability for a wide range of K (the difference in the planetary semimajor axes in units of the mutual Hill radius) and (unequal) planet masses. We find that, in general, the stable region (large K) and unstable region (small K) are separated by a “grey zone”, where the (in)stability is not guaranteed. We report the numerical values of the critical spacing for stability Kcrit and the “grey zone” range in different systems, and provide fitting formulae for arbitrary frictional forcing strength. We show that the stability of a system depends on the damping time-scale τ relative to the zero-friction instability growth time-scale tinst: two-planet systems are stable if tinst ≳ τ; three-planet systems require tinst ≳ 10τ−100τ. When K is sufficiently small, tinst can be less than the synodic period between the planets, which makes frictional stabilization unlikely to occur. As K increases, tinst tends to grow exponentially, but can also fluctuate by a few orders of magnitude. We also devise a linear map to analyse the dynamical instability of the “planet + test mass” system, and find qualitative agreement with N-body simulations.

Li, Jiaru (ORCID:0000000155507421)↗
NASA NTRS1982

The Orthogonal In-Situ Machining of Single and Polycrystalline Aluminum and Copper, Volume 1

Metal cutting is a unique deformation process characterized by large strains, exceptionally high strain rates and few constraints to the deformation. These factors, along with the difficulty of directly measuring the shear angle, make chip formation difficult to model and understand. One technique for skirting the difficulty of post mortem chip measurement is to perform a cutting experiment dynamically in a scanning electron microscope. The performance of the in-situ experiment with full instrumentation allows for component force measurement, orientation measurement (on a round single crystal disk) and a timing device, all superimposed below the deformation on the TV monitor and recorded for future viewing. This allows the sher angle to be directly measured for the screen along with the other needed information.

Cohen, P. H.↗
DOE OSTI2019

Experimental Research on Tensile Behavior of Advanced High-Strength Steel DP600 at High Strain Rate

We conducted a series of experimental investigations on the mechanical properties of DP600 dual-phase steel under strain rates from 0.001 to 3000 s{sup −1} at room temperature. A split Hopkinson tensile bar was used to capture a high strain rate response. A comparison of the quasi-static and dynamic experiment results showed that the yield strength and ultimate tensile strength increased significantly under dynamic conditions. Fractographs were analyzed by scanning electron microscopy, which indicated a better ductility at a high strain rate. Based on the experimental results, the Johnson–Cook constitutive model was applied to describe the tensile deformation behavior under various strain rates. A reasonable agreement was observed between the experimental data and the Johnson–Cook model. A metallographic analysis of tensile specimens showed that the average ferritic grain size of the fractured specimens at a high strain rate was smaller than that of the fractured specimens under quasi-static conditions. Ferritic grain refinement proved that high-speed forming could enhance the forming ability of the DP600 steel.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Cooperative Education

M-3 Focused Experiments is a group at Los Alamos National Lab (LANL) and is under the Dynamic Experiments Division. Their work surrounds the diagnostics and study of explosives and their interaction with materials. The data collected is used to better understand the erratic nature of explosions and high velocity projectiles. Through better comprehension of this science, the overall national security will be improved while innovations are made along the way. Despite the strong drive for research and development, the lab holds safety above all else and constantly updates procedures to protect LANL employees and their environment. At any time, there are multiple projects going on at once within the team and I am tasked with assisting the Firing Site Leaders and various research diagnosticians in any way possible with the setup, testing, and execution of data collection for each experiment. Such data includes velocity, fragmentation characteristics, and the spread of energy across the material to name a few. During my summer employment with the lab, my main goal is to maintain a questioning attitude and learn as much possible about the research and development side of science and engineering. Throughout the duration of the Co-op, many experiments will take place at specially designed firing sites which is where I will be spending most of my time.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2024

Dynamic changes in evapotranspiration, canopy photosynthesis and expansive growth in open field under rapid fluctuating radiation

Abstract In open fields, plants experience dynamic changes in environment, particularly radiation, temperature, wind, and humidity but their short-term responses have not been adequately characterized under natural conditions. In this study, we assessed causal effects of rapid radiation fluctuation on seven plant parameters in open fields of cotton and sweet corn canopies. The parameters are evapotranspiration ( ET ), canopy photosynthesis indicated by CO2 flux from air to canopy ( FCO2 ), sensible heat energy flux ( H ), canopy conductance for water vapor ( gcw ), canopy surface temperature ( Ts ), shoot and leaf elongation rate, and stem diameter change. The energy and CO2 fluxes were measured with Bowen ratio/energy balance/CO2 gradient (BREB+) technique, using averaging time of 5 min. Shoot + leaf elongation and stem diameter change were monitored with position transducers using averaging time of 1 min. All parameters were all found to respond to change in radiation and transpiration within minutes or sooner. While radiation effects on canopy gas exchanges are expected, illuminating are the indirect but immediate effects on shoot + leaf growth and stem diameter change through radiation effects on transpiration and plant water status. A novel finding is that gcw also responded within minutes or sooner to radiation fluctuations and that FCO2 was related almost linearly to gcw . Results are discussed in terms of soil-plant-atmosphere continuum, and interpreted in terms of dynamic interactions between transpiration and plant water status. The clear inverse relationship between ET and elongation rate or stem diameter changes provides additional evidence supporting the validity of 5-min averaging for the BREB + technique.

Hsiao, Theodore C.↗
DOE OSTI2025

Insights on the Influence of the Central-Cut Width of the Box Assembly with Removable Component on Its Dynamical Responses

This investigation focuses on the dynamical effects caused by varying the central-cut width within the Box Assembly with Removable Component (BARC) system. The central-cut widths included in this study are a 0.5″ cut, a 0.25″ cut, a thin 0.1″ cut, and a structure that did not have a cut at all. Finite element analysis was conducted to determine the mode shapes and natural frequencies of each of the BARC structures. Structural dynamics experiments were run to examine the effects of the central-cut width on the dynamical responses and nonlinear characteristics of the BARC system. Free vibration testing with an impact hammer was carried out to excite the system and extract the dominant frequencies and directions of the significant responses. A pseudorandom vibration test that allows for the qualitative determination of any nonlinear behavior within the system was performed. This type of behavior can include nonlinear softening, nonlinear hardening, and the most common, nonlinear damping due to the presence of several bolted-joint connections and the possible activation of geometric and inertia nonlinearities. To quantitatively investigate the impacts of the central-cut width on the dynamics of the system, swept sinusoidal testing was conducted. It is determined that almost all systems with central cuts demonstrate the presence of nonlinear softening, but at times, nonlinear hardening trends are seen, particularly in the 0.1″ cut and no-cut systems when testing harmonically. Each of the central-cut systems displays nonlinear damping, with the amount of damping generally increasing as the central cut decreases in size. The effect of the central cut of the BARC system on the mode-switching ability of the system is negligible; however, mode switching takes place when comparing the central-cut configurations to the no-cut one. These results show the significance of accurately measuring the central-cut width and how geometric uncertainty may change the dynamical responses and nonlinear properties of the system.

Padilla, Christopher (ORCID:000900033446732X)↗
NASA NTRS1992

Semiannual report, January 1992

The objective of the Space Engineering Research Center is to develop and disseminate a unified technology of controlled structures, to codify and disseminate this technology, and to train a generation of skilled engineers. The disciplinary research with the Controlled Structures Testbed (CST) is ongoing. The interferometer testbed became operational and is an active vehicle for researchers. The engineering model of the Mid-Deck Active Control Experiment (MACE) multibody test article also was commissioned. It is a pathfinder for control of articulated flexible structures. The Mid-Deck 0-Gravity Dynamics Experiment (MODE) experiment flew on STS-48. Its goals were to examine the dynamics of space structures in zero-gravity.

Source record↗
DOE OSTI2023

Dynamic oxidation of (Mn,Co) 3 O 4 -Coated interconnects for solid oxide electrolysis cells

Solid oxide electrolysis cell stacks are expected to experience dynamic conditions when using renewable electricity derived from wind or solar power. To address this scenario, (Mn,Co) 3 O 4 (MCO)-coated Crofer 22 APU interconnect coupons are subjected to thermal cycling, and intermittent current density, with gas compositions relevant to high-temperature electrolysis (elevated steam:hydrogen ratio and oxygen content). Defects are also intentionally introduced in the MCO coating, to assess whether the difference in oxidation properties of the adjacent coated and uncoated (defective) surfaces causes sufficient stress to damage the protective oxide scale. Specimens with defects are subjected to oxidation for 1000 h at 800 °C, or thermal cycling. Before thermal cycling, some specimens are pre-oxidized to create a thick oxide scale to mimic the scale thickness expected after ~30 kh operation. In all cases, the coating and oxide scale remain well adhered with no cracking observed. Area-specific resistance (ASR) is monitored in both single-atmosphere and dual-atmosphere conditions, and the ASR is stable and is not impacted by dynamic cycling of the current density. Finally, this work provides confidence that the MCO coated interconnect will function as needed in dynamic operation conditions, even with coating defects.

08 HYDROGEN↗
NASA NTRS1978

Experiments on the dynamic behavior of cavitating pumps

This paper describes experiments performed to measure the dynamic transfer matrices for cavitating (and noncavitating) pumps. These transfer matrices describe the relationship between small linear oscillatory perturbations in the pressures and mass flow rates at inlet and discharge from the hydraulic machine. The matrices were deduced from direct measurements of these fluctuating quantities for different modes of excitation of the machine. Results for a cavitating inducer are presented as functions of frequency and mean operating state. Though some of the trends in the data are consistent with existing theoretical models of inducer dynamics, others are not, indicating a need for further theoretical investigation of the dynamic characteristics of such flows. The results exhibit increasingly complex dynamics with increasing cavitation; it appears that the hydraulic machine deviates from an essentially passive response without cavitation to an increasingly active response as the cavitation number is reduced.

Ng, S. L.↗
NASA NTRSDate not supplied

Aero-Propulsive Modeling for eVTOL Aircraft Using Wind Tunnel Testing with Multisine Inputs

A novel approach for modeling the aero-propulsive characteristics of an electric vertical takeoff and landing (eVTOL) aircraft was developed and demonstrated in wind tunnel testing. The approach was applied to the NASA LA-8 tandem tilt-wing eVTOL aircraft, using an efficient, hybrid experiment design composed of a static I-optimal response surface design for slowly-varying test variables, and dynamic orthogonal phase-optimized multisine excitations for the control surfaces and electric propulsors. Both the static and dynamic experiment designs were executed simultaneously to collect informative data for model identification. Statistically-weighted multivariate orthogonal function modeling was used to combine local modeling results computed in the frequency domain using data collected with dynamic excitations operating on the control effectors to form an aggregate aero-propulsive model. The final identified model exhibited good predictive capability when compared to validation data acquired separately from the data used to develop the model. The required test time using these new techniques was reduced by at least a factor of five compared to previous static wind tunnel testing for the LA-8 aircraft, while providing more informative data, greater parameterization flexibility, and high-quality models.

system identification↗
DOE OSTI2021

Cinema:Snap: Real-time tools for analysis of dynamic diamond anvil cell experiment data

We report we developed tools and a workflow for real-time analysis of data from dynamic diamond anvil cell experiments performed at user light sources. These tools allow users to determine the phases of matter observed during the compression of materials in order to make decisions during an experiment to improve the quality of experimental results and maximize the use of scarce experimental facility time. The tools fill a gap in dynamic compression data analysis tools that are real-time, are flexible to the needs of high-pressure scientists, connect to automated processing of results, can be easily incorporated into workflows with existing tools and data formats, and support remote experimental data analysis workflows. Specific analytics developed include novel automated two-peak analysis for overlapping peaks and multiple phases, coordinated views of pressure and temperature values, full-compression contour plots, and configurable views of integrated x-ray diffraction. We present an experimental use case to show how the tools produce real-time analytics that help the scientists revise parameters for the next compression

47 OTHER INSTRUMENTATION↗