Search NASA⌕ Search

SEARCH · Search NASA

Results for “effective diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Hydrogen effects on thermal diffusivity and electrical resistivity of zircaloy cladding

Thermal diffusivity measurements on Zirconium-based cladding materials have historically been a challenge due to the difficulty to measure on specimens with curved geometries, including nuclear grade Zircaloy cladding materials. Here, in this work, we first used laser flash analysis method and four-probe configuration method to measure the thermal diffusivity and electrical resistivity of Zircaloy tubes respectively, which show good agreement with Zircaloy plates in this work, as well as previously published data. The consistent results proved the applicability of the laser flash analysis setup and four-probe configuration method for investigating thermal diffusivity and electrical resistivity of Zircaloy tubes. We further investigated the hydrogen effect on thermal diffusivity and electrical resistivity of Zircaloy. Hydrogen plays significant roles in the thermal diffusivity of Zircaloy, which depends on the hydrogen concentration. For higher hydrogen contents (1130 and 1820 wppm in this work), where phase transformation (α-Zr + δ-hydride → α-Zr + β-Zr) occurs at 567 °C, thermal diffusivity decreases as a function of temperature at the α-Zr + δ-hydride phase regime, while increase at higher temperature at the α-Zr + β-Zr phase regime. For low hydrogen concentration, where hydride dissolved into α-Zr matrix phase at higher temperature, the thermal diffusivity is lower than non-hydrided Zircaloy-4 with similar temperature-dependent trends. Such observation demonstrates the hydrogen effects on reducing thermal diffusivity of α-Zr phase. Hydrogen increases the electrical resistivity of Zircaloy. Similar to thermal diffusivity results, the phase transformation causes a reversal of temperature-dependent trends in electrical resistivity results in Zircaloy-4 with higher hydrogen contents.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Simulating Dopant Diffusion in a Detalied Porous Structure

The National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) uses highpowered lasers to explore cutting edge fusion technology. Specialized optics, known as fiber lasers, generate and amplify the NIF’s high-powered lasers that facilitate fusion experiments. Fiber lasers are glass fibers that are doped with heavy elements to stimulate light emission. The fiber laser doping processing uses a predeposited layer of porous silica nanoparticles on the surface of the glass to absorb a dopant rich salt solution. Our project simulated the diffusion of dopants into porous silica with prescribed colloidal stacking geometries using COMSOL Multiphysics. With these simulations we identified the porosity and tortuosity of the porous nanoparticle structures as the primary parameters that will dictate how the dopants will diffusive into the porous surface of the glass. Porosity and Tortuosity are geometric parameters that can easily be input into more detailed simulations to estimate an effective diffusivity within the porous layer. Future work should account for surface reactions to accurately simulate the full-scale diffusion of the solution doping process.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Performance of high-area-ratio annular dump diffuser using suction-stabilized-vortex flow control

A short annular dump diffuser having a geometry conductive to formation of suction stabilized toroidal vortices in the region of abrupt area change was tested. The overall diffuser area ratio was 4.0 and the length to inlet height ratio was 2.0. Performance data were obtained at near ambient temperature and pressure for inlet Mach numbers of 0.18 and 0.30 with suction rates ranging from 0 to 18 percent of total inlet mass flowrate. Results show that the exit velocity profile could be readily biased toward either wall by adjustment of inner and outer wall suction rates. Symmetric exit velocity profiles were inherently unstable with a tendency to revert to a hub or tip bias. Diffuser effectiveness was increased from about 38 percent without suction to over 85 percent at a total suction rate of 10 to 12 percent. At the same time diffuser total pressure loss was reduced from 3.1 percent to 1.1 percent at an inlet Mach number of 0.3.

Juhasz, A. J.↗
DOE OSTI2023

Hydrogen Diffusion Coefficient Measures on Thin Film Uranium Oxide

Thin films of uranium oxides, putatively UO 2 and U 3 O 8 , were deposited on palladium/silver (75/25) foil discs (10 μm thick, 10 mm diameter). Methodology for sealing these foils, applying a hydrogen pressure (~ 1 atm) to the oxide side, and measuring the pressure on the permeate side (opposite side of foil) is reported. The experimental apparatus is held at 100 °C to speed diffusion, aided by the pressure differential across the foil (~1 atm (750 torr) on oxide side, initially low vacuum on permeate side, ~1x 10 -4 torr). Early results indicate an effective diffusion coefficient of roughly 7.66 x 10 -17 +/- 2.22 x 10 -17 cm 2 /sec for UO 2 . These values are in line with expectations and prior measures relative to large lag times for system baseline (substrate only). Evaluation of the technique for U 3 O 8 thin films suggests further development will be needed to extend the technique to more oxidized films (U 3 O 8 , UO 3 ). Characterization of the foils (thickness and speciation) post diffusion experiments will be carried out by SIGMA (Eric Tegtmeier and Andy Richards) in FY24 which will sharpen the uncertainty quantification for UO 2 diffusion coefficients, aiding the nucleation model for DRACO.

36 MATERIALS SCIENCE↗
NASA NTRS1998

Directional Solidification and Characterization of Hg(0.89) Mn(0.11)Te

Two boules of Hg(0.89)Mn(0.11)Te(MMT) were solidified using the vertical Bridgman-Stockbarger method. Translation rates of 0.09 and 0. 18 microns/s were used. The influence of growth rate on axial compositional homogeneity in the MMT boules was evaluated experimentally by conducting precision density measurements on radial slices taken from each boule. In addition, Plane Front Solidification theory and segregation coefficient (k) data for the Hg(1-x)Mn(x)Te system were used to fit theoretical composition profiles to the measured MMT axial composition profiles. The strong correlation between the measured and calculated MMT axial composition profiles indicates diffusion dominated axial solute redistribution in the boules under the applied growth conditions. The analysis of the MMT axial composition profiles by Plane Front Solidification theory allowed the calculation of the effective diffusion coefficient (D(eff) = 3.5 x l0(exp -5) sq cm/s). The k-values for the Hg(1-x)Mn(x)Te system and the D(sub eff) - value were then used to verify that both boules were solidified under conditions which did not exceed the Constitutional Supercooling Criteria under ideal conditions. Finally, a preliminary examination of the radial compositional variation in each MMT was made using Fourier Transform Infra-Red Spectroscopy (FTIR). The radial homogeneity in the MMT boules was found to be comparable for both translation rates.

Price, M. W.↗
NASA NTRS1985

Dendritic solidification. III - Some further refinements to the model for dendritic growth under an imposed thermal gradient

Some further refinements to a simple model for dendritic solidification in a binary alloy melt under an imposed positive thermal gradient are presented. Two new expressions for the dendrite tip undercooling have been obtained and shown to yield a limiting value of Delta T sub 0 and very small growth rates. Here Delta T sub 0 is the equilibrium solidification range of the alloy. At very large growth rates, all three tip undercooling expressions reach the same limiting value depending on the value of a dimensionless parameter lambda which is related to the effective diffusion distance ahead of the dendrite tip. The predicted tip undercoolings are, however, somewhat lower at intermediate growth rates. An improved calculation for the solute buildup at the dendrite tip due to curvature effects is also included.

Laxmanan, V.↗
DOE OSTI2025

HIGH-FIDELITY SIMULATION OF SOOT FORMATION AND THERMAL RADIATION IN A LABORATORY-SCALE RICH-QUENCH-LEAN BURNER

High-fidelity simulations of a swirl-stabilized turbulent spray flame in a laboratory-scale aero-combustor have been performed to evaluate the predictability of state-of-the-art models in capturing soot formation. The simulations employ a complex chemical mechanism developed for Jet-A with PAH chemistry, coupled with the Hybrid Method of Moments (HMOM) soot model, and a Lagrangian dilute spray model for the fuel injection. Two simulations are performed to compare the results when thermal radiation is neglected or included in the solution with a mean spectral model. Modeling closures for the soot differential diffusion effects in mixture fraction space, as well as turbulence-radiation interaction are also evaluated using the data generated by the simulations. Given the degree of complexity of the simulation, the results showed good agreement with experimental measurements of the spatial distribution of the soot volume fraction ensemble average. A closer agreement with the experiment is observed when thermal radiation is included in the solution. Thermal radiation is observed to reduce the flame temperature and increase the flame intermittency, denoted by the increase in the temperature standard deviation in mixture fraction space. The reduction in temperature also leads to a reduction in PAH production and soot volume fraction. Turbulence is observed to have different effects on radiative emission depending on the mixture fraction. Turbulent scalar fluctuations significantly enhance radiative emission in fuel lean mixtures and can also play a role for fuel rich conditions. The statistical description of the turbulence-radiation interaction, previously proposed in the literature, was observed to correctly reproduce the high-fidelity results. Model coefficients were provided for swirl-stabilized flames. The soot differential diffusion model, previously proposed in the literature, based on the residual between the exact term and its model approximation, was also evaluated. The residual correction term further improved the agreement with exact differential diffusion term evaluated with the high-fidelity simulation data in mixture fraction space. The results suggest that the effective turbulent Lewis number can be equal to unity in simulations of turbulent non-premixed recirculating flames.

Soriano, Bruno [Sandia National Laboratories (SNL)↗
DOE OSTI2020

Mesoscopic analyses of the impact of morphology and operating conditions on the transport resistances in a proton-exchange-membrane fuel-cell catalyst layer

Exploring the origins of local transport resistance and characterizing the oxygen transport resistances in the catalyst layer (RCL) are critical for cost reduction. In this paper, a comprehensive mesoscopic model for simulating coupled transport processes of oxygen and water vapor for different structural parameters under different operating conditions in reconstructed microstructures is proposed. The local transport resistance is calculated after achieving the limiting current density and the effective diffusivity of oxygen. The results demonstrate that RCL increases greatly with decreasing platinum loading (LPt) and the transport resistances in other components of the cell dominate for high-loadings. Both the reduced oxygen permeation coefficient in the ionomer thin-film and the adsorption resistance account for the origins of local transport resistance. The local transport resistance increases with the bare carbon ratio for a constant LPt and Pt/C ratio due to the decreased effective ionomer surface, and increases with the I/C ratio due to the increased ionomer thickness and decreased Knudsen diffusivity. Due to the presence of liquid water, a slight decrease followed by an increase of the local transport resistance versus relative humidity is obtained. The contribution of ionomer thin-films to RCL is more sensitive to liquid saturation compared with that of pores. This journal is

Mu, YT↗
NASA NTRS1974

Tidal waves within the thermosphere

The eigenfunctions of the atmosphere (the Hough functions within the lower atmosphere below about 100 km) change their structure and their propagation characteristics within the thermosphere due to dissipation effects such as heat conduction, viscosity, and ion drag. Wave dissipation can be parameterized to a first-order approximation by a complex frequency, the imaginary term of which simulates an effective ion drag force. It is shown how the equivalent depth, the attenuation, and the vertical wavelength of the predominant symmetric diurnal tidal modes change with height as functions of effective ion drag. The boundary conditions of tidal waves are discussed, and asymptotic solutions for the wave parameters like pressure, density, temperature, and wind generated by a heat input proportional to the mean pressure are given. Finally, diffusion effects upon the minor constituents within the thermosphere are described.

Volland, H.↗
NASA NTRS1980

Development of low cost contacts to silicon solar cells

The results of the second phase of the program of developing low cost contacts to silicon solar cells using copper are presented. Phase 1 yielded the development of a plated Pd-Cr-Cu contact system. This process produced cells with shunting problems when they were heated to 400 C for 5 minutes. Means of stopping the identified copper diffusion which caused the shunting were investigated. A contact heat treatment study was conducted with Pd-Ag, Ci-Ag, Pd-Cu, Cu-Cr, and Ci-Ni-Cu. Nickel is shown to be an effective diffusion barrier to copper.

Tanner, D. P.↗
DOE OSTI2020

3D Morphology of Bimodal Porous Copper with Nano-Sized and Micron-Sized Pores to Enhance Transport Properties for Functional Applications

Multiscale porous metals with multiscale porosity from nanometer to micrometer have a high specific surface area and high effective diffusivity for ion transport, thereby enhancing functionalities and extending the applications of porous metals. Herein, the Cu–Fe–Al ternary system was selected as the precursor alloy to construct multiscale, bimodal porous copper by the chemical dealloying method. The effect of the phase composition and initial microstructure of precursor alloys (Al x Fe 75– x Cu 25 , x = 10–60) on the three-dimensional (3D) morphology of multiscale porous metals was systematically investigated, with a goal to precisely control the multiscale porous structure. The four crystal structure phases (body-centered cubic (BCC), face-centered cubic (FCC), CsCl type (B2), and monoclinic) in precursor alloys were analyzed by synchrotron X-ray diffraction refinement. The 3D morphology, feature size distribution, and tortuosity of four representative porous Cu after dealloying Al x Fe 75– x Cu 25 ( x = 10, 30, 50, and 60) precursor alloys were directly visualized and quantified via advanced synchrotron X-ray nanotomography. The relationship between the phases/crystal structures of precursor alloys and their corresponding porous morphology was established: the micron-sized pores in bimodal porous Cu are formed by dissolving the CuFeAl phase with BCC and monoclinic crystal structures, and the nano-sized pores are formed by dealloying the CuFeAl phase with FCC and B2 crystal structures. The size of the nanoporous structure depends on the ratio between the more noble and more active components in the precursor alloy, while the size of the microporous structure depends on the corresponding phase size in the precursor alloy. The tortuosity results showed that the multiscale porous structure with both nanoporosity and microporosity exhibits lower tortuosity, which will enhance transport properties for functional applications.

25 ENERGY STORAGE↗
NASA NTRS1974

Performance of a short annular dump diffuser using wall trailing-edge suction

A short annular dump (abrupt flow area change) diffuser was tested with suction through wall trailing-edge slots at inlet Mach numbers of 0.19 and 0.27 and at near ambient inlet temperature and pressure, with suction flow varied from zero to 10 percent of the inlet air mass-flow rate. The overall ratio of diffuser exit area to inlet area was 4.0, and the ratio of length to inlet height was 2.0. By applying suction flow separately on either wall or to both walls simultaneously, the original annular jet profile could be altered to either a hub- or tip-biased profile. Diffuser effectiveness was increased from about 25 percent with no suction to 50 percent at 6 percent outer-wall suction and to 52 percent at a combined suction rate on both walls of 10.25 percent. At the same time, diffuser total pressure loss was reduced by one-fourth.

Juhasz, A. J.↗
DOE OSTI2022

Estimates of Quantum Tunneling Effects for Hydrogen Diffusion in PuO 2

We detail the estimation of activation energies and quantum nuclear vibrational tunneling effects for hydrogen diffusion in PuO 2 based on Density Functional Theory calculations and a quantum double well approximation. We find that results are relatively insensitive to choice of exchange correlation functional. In addition, the representation of spin in the system and use of an extended Hubbard U correction has only a small effect on hydrogen point defect formation energies when the PuO 2 lattice is held fixed at the experimental density. We then compute approximate activation energies for transitions between hydrogen interstitial sites seeded by a semi-empirical quantum model and determine the quantum tunneling enhancement relative to classical kinetic rates. Our model indicates that diffusion rates in H/PuO 2 systems could be enhanced by more than one order of magnitude at ambient conditions and that these effects persist at high temperature. The method we propose here can be used as a fast screening tool for assessing possible quantum nuclear vibrational effects in any number of condensed phase materials and surfaces, where hydrogen hopping tends to follow well defined minimum energy pathways.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1978

The development of a three-dimensional partially elliptic flow computer program for combustor research

A three dimensional, partially elliptic, computer program was developed. Without requiring three dimensional computer storage locations for all flow variables, the partially elliptic program is capable of predicting three dimensional combustor flow fields with large downstream effects. The program requires only slight increase of computer storage over the parabolic flow program from which it was developed. A finite difference formulation for a three dimensional, fully elliptic, turbulent, reacting, flow field was derived. Because of the negligible diffusion effects in the main flow direction in a supersonic combustor, the set of finite-difference equations can be reduced to a partially elliptic form. Only the pressure field was governed by an elliptic equation and requires three dimensional storage; all other dependent variables are governed by parabolic equations. A numerical procedure which combines a marching integration scheme with an iterative scheme for solving the elliptic pressure was adopted.

Pan, Y. S.↗
DOE OSTI2022

An electrochemical mesoscale tool for modeling the corrosion of structural alloys by molten salt

Understanding the impact of microstructure on corrosion rates can aid the development of corrosion-resistant alloys for molten salt reactors. Here in this work, we develop an electrochemical phase-field model for capturing the microstructure-dependent corrosion of structural alloys by molten salts. As a demonstration problem, we apply this model to capture the selective depletion of Cr from Ni-Cr grain boundaries during corrosion in molten FLiBe salt. We perform sensitivity analysis and model verification on 1D simulations to confirm that the model predicts diffusion-limited kinetics. The model is validated using 1D, 2D, and 3D simulations against experimental data for Ni-5Cr and Ni-20Cr corrosion in molten FLiBe. The 1D simulations predict the corrosion behavior with reasonable accuracy when using an effective diffusion coefficient that accurately represents the grain boundary diffusion. 2D simulations that represent the grain structure underpredict the corrosion. 3D simulations that represent the grain structure predict the corrosion with reasonable accuracy. The corrosion rate predicted by the 3D simulations is proportional to the average grain size at the alloy/salt interface.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗