Search NASA⌕ Search

SEARCH · Search NASA

Results for “fitting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Interference-Fit Life Factors for Ball Bearings

The effect of hoop stresses on the rolling-element fatigue life of angular-contact and deep-groove ball bearings was determined for common inner-ring interference fits at the ABEC-5 tolerance level. The analysis was applied to over 1150 bearing configurations and load cases. Hoop stresses were superimposed on the Hertzian principal stresses created by the applied bearing load to calculate the inner-race maximum shearing stress. The resulting fatigue life of the bearing was recalculated through a series of equations. The reduction in the fatigue life is presented as life factors that are applied to the unfactored bearing life. The life factors found in this study ranged from 1.00 (no life reduction)--where there was no net interface pressure--to a worst case of 0.38 (a 62-percent life reduction). For a given interference fit, the reduction in life is different for angular-contact and deep-groove ball bearings. Interference fits also affect the maximum Hertz stress-life relation. Experimental data of Czyzewski, showing the effect of interference fit on rolling-element fatigue life, were reanalyzed to determine the shear stress-life exponent. The Czyzewski data shear stress-life exponent c equals 8.77, compared with the assumed value of 9. Results are presented as tables and charts of life factors for angular-contact and deep-groove ball bearings with light, normal, and heavy loads and interference fits ranging from extremely light to extremely heavy.

Oswald, Fred B.↗

Best-Fit Conic Approximation of Spacecraft Trajectory

A computer program calculates a best conic fit of a given spacecraft trajectory. Spacecraft trajectories are often propagated as conics onboard. The conic-section parameters as a result of the best-conic-fit are uplinked to computers aboard the spacecraft for use in updating predictions of the spacecraft trajectory for operational purposes. In the initial application for which this program was written, there is a requirement to fit a single conic section (necessitated by onboard memory constraints) accurate within 200 microradians to a sequence of positions measured over a 4.7-hour interval. The present program supplants a prior one that could not cover the interval with fewer than four successive conic sections. The present program is based on formulating the best-fit conic problem as a parameter-optimization problem and solving the problem numerically, on the ground, by use of a modified steepest-descent algorithm. For the purpose of this algorithm, optimization is defined as minimization of the maximum directional propagation error across the fit interval. In the specific initial application, the program generates a single 4.7-hour conic, the directional propagation of which is accurate to within 34 microradians easily exceeding the mission constraints by a wide margin.

Singh, Gurkipal↗

Evaluating Suit Fit Using Performance Degradation

The Mark III planetary technology demonstrator space suit can be tailored to an individual by swapping the modular components of the suit, such as the arms, legs, and gloves, as well as adding or removing sizing inserts in key areas. A method was sought to identify the transition from an ideal suit fit to a bad fit and how to quantify this breakdown using a metric of mobility-based human performance data. To this end, the degradation of the range of motion of the elbow and wrist of the suit as a function of suit sizing modifications was investigated to attempt to improve suit fit. The sizing range tested spanned optimal and poor fit and was adjusted incrementally in order to compare each joint angle across five different sizing configurations. Suited range of motion data were collected using a motion capture system for nine isolated and functional tasks utilizing the elbow and wrist joints. A total of four subjects were tested with motions involving both arms simultaneously as well as the right arm by itself. Findings indicated that no single joint drives the performance of the arm as a function of suit size; instead it is based on the interaction of multiple joints along a limb. To determine a size adjustment range where an individual can operate the suit at an acceptable level, a performance detriment limit was set. This user-selected limit reveals the task-dependent tolerance of the suit fit around optimal size. For example, the isolated joint motion indicated that the suit can deviate from optimal by as little as -0.6 in to -2.6 in before experiencing a 10% performance drop in the wrist or elbow joint. The study identified a preliminary method to quantify the impact of size on performance and developed a new way to gauge tolerances around optimal size.

Margerum, Sarah E.↗

Strain Gage Load Calibration of the Wing Interface Fittings for the Adaptive Compliant Trailing Edge Flap Flight Test

The safety-of-flight parameters for the Adaptive Compliant Trailing Edge (ACTE) flap experiment require that flap-to-wing interface loads be sensed and monitored in real time to ensure that the structural load limits of the wing are not exceeded. This paper discusses the strain gage load calibration testing and load equation derivation methodology for the ACTE interface fittings. Both the left and right wing flap interfaces were monitored; each contained four uniquely designed and instrumented flap interface fittings. The interface hardware design and instrumentation layout are discussed. Twenty-one applied test load cases were developed using the predicted in-flight loads. Pre-test predictions of strain gage responses were produced using finite element method models of the interface fittings. Predicted and measured test strains are presented. A load testing rig and three hydraulic jacks were used to apply combinations of shear, bending, and axial loads to the interface fittings. Hardware deflections under load were measured using photogrammetry and transducers. Due to deflections in the interface fitting hardware and test rig, finite element model techniques were used to calculate the reaction loads throughout the applied load range, taking into account the elastically-deformed geometry. The primary load equations were selected based on multiple calibration metrics. An independent set of validation cases was used to validate each derived equation. The 2-sigma residual errors for the shear loads were less than eight percent of the full-scale calibration load; the 2-sigma residual errors for the bending moment loads were less than three percent of the full-scale calibration load. The derived load equations for shear, bending, and axial loads are presented, with the calculated errors for both the calibration cases and the independent validation load cases.

Miller, Eric J.↗

NASA Computational Case Study: Spectral Energy Distribution Fitting

The need for faster, more efficient algorithms is an important aspect of scientific computing. Generally, scientists are only exposed to computational issues that arise in their field. Thus, collaboration between a numerical analyst and a scientist is becoming necessary for scientific computing. The purpose of this case study is to expose computer scientists to processes that an astronomer would use to obtain useful results from raw data. For example, astronomers are interested in determining the properties of galaxies and measuring changes in those properties as a function of time throughout cosmic history. To do so, they use certain models that are designed and refined over time via observations at different wavelengths of the light spectrum. The process of matching these models with observed data from studying celestial bodies is referred to as Spectral Energy Distribution (SED) fitting. In this case study, we learn how to perform the SED fit. This process requires knowledge of both the astronomical and computational issues involved when fitting flux, the total energy from a source as seen from Earth, to a set of physical templates. Once a fit is complete, one can classify the source and estimate a number of physical parameters. The goal is to demonstrate how the computer science skill set can be used in the scientific community and to possibly improve one or more of the computational aspects of this problem. The following provides some background on the astronomy issues, including information on the spectral energy distribution and related physical parameters, and the computational issues, including the fitting procedure..

modeling↗

Kepler Data Validation II–Transit Model Fitting and Multiple-Planet Search

This paper discusses the transit model-fitting and multiple-planet search algorithms and performance of the Kepler Science Data Processing Pipeline, developed by the Kepler Science Operations Center (SOC). Threshold crossing events (TCEs), which are transit candidate events, are generated by the Transiting Planet Search (TPS) component of the pipeline and subsequently processed in the data validation (DV) component. The transit model is used in DV to fit TCEs to characterize planetary candidates and to derive parameters that are used in various diagnostic tests to classify them. After the signature associated with the TCE is removed from the light curve of the target star, the residual light curve goes through TPS again to search for additional TCEs. The iterative process of transit model fitting and multiple-planet search continues until no TCE is generated from the residual light curve or an upper limit is reached. The transit model-fitting and multiple-planet search performance of the final release (9.3, 2016January) of the pipeline is demonstrated with the results of the processing of four years (17 quarters) of flight data from the primary Kepler Mission. The transit model-fitting results are accessible from the NASA Exoplanet Archive. The final version of the SOC codebase is available through GitHub.

Threshold crossing events (TCEs↗

PolyFit: A C++ code for Polynomial Curve Fit with Calculation of Error Bars

In radiobiology, many dose-response results are modeled using the so-called linear-quadratic (LQ)model, which means that results are modeled as a function of dose Das 𝑅(𝐷)=𝛽0+𝛽1𝐷+𝛽2𝐷2. The coefficients 𝛽0, 𝛽1and 𝛽2are obtained from fitting a series of data points (𝑥𝑖, 𝑦𝑖), which is usually done using a least-square method. The LQ and more generally the polynomial fit capability is implemented in many software that analyzes data. However, there are some instances where the fitting needs to be done programmatically. Furthermore, depending on the software used, some features may not be implemented. In this mini-review, I discuss the basis of polynomial fitting, including the calculation of errors on the coefficients and results, use of weighting and fixing the intercept value (the coefficient 𝛽0). A simple C++ code to perform the polynomial curve fitting is also provided. This code should be useful not only in radiobiology but in other fields of science as well.

Ianik Plante↗

PolyFit: A C++ code for Polynomial Curve Fit with Calculation of Error Bars

In radiobiology, many dose-response results are modeled using the so-called linear-quadratic(LQ)model, which means that results are modeled as a function of dose Das 𝑅(𝐷)=𝛽0+𝛽1𝐷+𝛽2𝐷2. The coefficients 𝛽0, 𝛽1and 𝛽2are obtained from fitting a series of data points (𝑥𝑖,𝑦𝑖), which is usually done using a least-square method. The LQ and more generally the polynomial fit capability is implemented in many software that analyzes data. However, it is often convenient to do the fitting programmatically, especially when a large number of datasets should be analyzed. Furthermore, depending on the software used, some features may not be implemented. In this mini-review, I discuss the basis of polynomial fitting, including the calculation of errors on the coefficients and results, use of weighting and fixing the intercept value (the coefficient 𝛽0). A simple C++ code to perform the polynomial curve fitting is also provided. This code should be useful not only in radiobiology but in other fields of science as well.

Ianik Plante↗

Development of Lunar EVA Fitness for Duty Standards for Aerobic Capacity and Muscle Strength

Current aerobic Fitness Standards for NASA astronauts are based on peak aerobic capacity (i.e. VO2peak (ml/kg/min))and are related to aerobic metabolic requirements for Extravehicular Activity (EVA) in microgravity and in 1 g operational environments. Standards for muscle strength need to be developed. Fitness for Duty Standards for partial gravity EVA (e.g. 1/6 g EVA on the Lunar surface) are not developed in terms of aerobic fitness and muscle strength. Defining thresholds for aerobic fitness and muscle strength will help to provide guidance in determining recommendations for optimal fitness necessary for partial g EVA success.

D Frisco↗

Validation of Fitness for Duty Standards Using Pre- and Post-Flight Capsule Egress and Suited Functional Performance Tasks in Simulated Reduced Gravity

The transition between gravity environments will involve one of the most complex, high-risk phases of any mission. For example, the reduced functional capacity caused by physiological deconditioning adaptations in microgravity coupled with the stressors of re-entry into partial gravity environments will increase risks to crew, even with rigorous adherence to inflight countermeasures. Quantification of the astronauts’ post-landing functional performance is necessary to design ConOps for exploration missions. Specifically, these two high-risk scenarios may be required to be performed soon after gravity transitions: • Nominal and/or emergency unassisted capsule egress task after return to Earth • Planetary extravehicular activity (EVA) soon after landing on Mars or the Moon This study is broken down into two phases. Phase 1: A feasibility study that will assess the overall feasibility and demonstrate the capability to do these tasks shortly after landing. Phase 2: the full Egress Fitness study, which is part of the CIPHER complement. This study uses a task-based approach to characterize functional performance of these high-risk scenarios in long-duration ISS crewmembers before flight and shortly after return to Earth. Prior to any testing, each astronaut subject completes a suit fit check to ensure adequate sizing and a mobility assessment to confirm completion of the EVA tasks. Pilot Egress Fitness pre-flight and post-flight testing includes an Earth-based emergency egress out of a functional capsule mockup and a short Mars gravity EVA simulation including suit donning, hatch egress, ladder descent, task board cable operations, baggage transfer over sand/rocky regolith, alignment with a rear entry port, and suit egress. Pre-flight testing will occur at any time point prior to flight. Post-flight assessment is much more critical with the capsule egress test that will occur 1–4 hours after landing and the planetary EVA approximately 18–36 hours after landing. The CIPHER study will incorporate additional pre-flight sessions, longer EVA tasks that include traverse and geology sampling, and post-flight sessions on R+1, 4, and 8 to characterize the timeframe of recovery. Data collected for both tasks include task completion time, photo, and video. The EVA portion also includes collection of metabolic and heart rate. Pilot Egress Fitness study has completed both baseline and post-flight testing on four astronaut subjects, with all four able to complete post-flight EVA testing and three able to complete postflight capsule egress testing. Preliminary results observe individual physiological variations, which were to be expected but also suggest the need to carefully track the timeline from undock to landing to testing. Furthermore, some task performance instructions and equipment may need to be adjusted to ensure results are primarily physiological. These and other lessons learned will be addressed with minor protocol changes in the full CIPHER Egress Fitness study.

J R Norcross↗

CIPHER: Egress Fitness

The transition between gravity environments will involve one of the most complex, high-risk phases of exploration missions. The reduced functional capacity caused by physiological deconditioning adaptations in microgravity coupled with the stressors of re-entry into partial gravity environments will increase risks to crew, even with rigorous adherence to inflight countermeasures. Specifically, two high-risk scenarios may be required to be performed soon after gravity transitions: 1) nominal and/or emergency unassisted capsule egress task after return to Earth, and 2) planetary extravehicular activity (EVA) soon after landing on Mars or the Moon. Quantification of crewmember’s functional performance after long-duration spaceflight is necessary to inform concepts of operations for future exploration missions. The overarching aim of this study is to quantify post-landing functional performance with deconditioning after long-duration ISS missions. This study is broken down into two phases. Phase 1 includes a pilot study to assess the overall feasibility and demonstrate the capability to perform mission-like tasks shortly after landing. Phase 2, the Egress Fitness study, which is part of the Complement of Integrated Protocols for Human Exploration Research (CIPHER), uses a task-based approach to characterize functional performance in long-duration ISS crewmembers before flight and shortly after return to Earth. The pilot and full Egress Fitness study includes pre-flight and post-flight testing of simulated emergency egress out of a functional capsule mockup and a Mars gravity EVA simulation at the Active Response Gravity Offload System (ARGOS) facility. The EVA simulation tasks include suit donning, hatch egress, ladder descent, task board cable operations, baggage transfer over sand/rocky regolith, alignment with a rear entry port, and suit egress. The post-flight simulated capsule egress test occurs 1–4 h after landing and the planetary EVA simulation occurs 18–36 h after landing. The full CIPHER Egress Fitness study has additional pre-flight sessions, longer EVA tasks that include traverse and geology sampling, and post-flight sessions on R+1, 4, and 8 to characterize the timeframe of recovery. Pilot Egress Fitness has completed baseline and post-flight testing on four crewmembers. That study remains open. Originally this was to cover the Boeing CFT mission, but now also includes private astronauts on commercial spaceflights. CIPHER study data collection is ongoing with 2 subjects completed and 4 additional subjects consented. This study will quantify post-landing functional performance in operationally relevant simulations to help inform fitness for duty standards and future planetary concepts of operations shortly after landing.

Jason Norcross↗

Ultrasonic Phased Array Evaluation of Control Rod Drive Mechanism (CRDM) Nozzle Interference Fit and Weld Region

Ultrasonic phased array data were collected on a removed-from-service CRDM nozzle specimen to assess a previously reported leak path. First a mock-up CRDM specimen was evaluated that contained two 0.076-mm (3.0-mil) interference fit regions formed from an actual Inconel CRDM tube and two 152.4-mm (6.0-in.) thick carbon steel blocks. One interference fit region has a series of precision crafted electric discharge machining (EDM) notches at various lengths, widths, depths, and spatial separations for establishing probe sensitivity, resolution and calibration. The other interference fit has zones of boric acid (crystal form) spaced periodically between the tube and block to represent an actively leaking CRDM nozzle assembly in the field. Ultrasonic phased-array evaluations were conducted using an immersion 8-element annular 5.0-MHz probe from the tube inner diameter (ID). A variety of focal laws were employed to evaluate the interference fit regions and J grove weld, where applicable. Responses from the mock-up specimen were evaluated to determine detection limits and characterization ability as well as contrast the ultrasonic response differences with the presence of boric acid in the fit region. Nozzle 63, from the North Anna Unit-2 nuclear power plant, was evaluated to assess leakage path(s) and was destructively dismantled to allow a visual verification of the leak path(s).

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Quantitative analysis of Cu XANES spectra using linear combination fitting of binary mixtures simulated by FEFF9

We report x-ray absorption near edge structure (XANES) is a powerful tool to probe the fingerprint of local structures, and when coupled with X-ray microscopy, the small spot size enables one to probe very specific regions of interest in a device or material, e.g. interfaces/bulk, different grains, good/bad electrical areas. In this work, we investigate the use of linear combination fitting (LCF) of XANES spectra for the particular case of Cu doping in CdTe. We show that the experimental data seem to be accurately represented by standards of Cu 2 Te and its substoichiometric counterpart, Cu 1.43 Te. We use Cu in CdTe as a case study to evaluate the accuracy of linear combination fitting using simulated standards, given that experimental standards for certain phases (e.g. Cu 1.43 Te) or defect structures (e.g. vacancies) cannot be readily obtained. We discuss how spectral features of the FEFF9-simulated standards, fitting ranges, and noise levels all dictate the accuracy of this type of analysis. We show that the greater the spectral difference between the two standards, the better the LCF is able to differentiate between the two structures and to tolerate experimental noise. Finally, we estimate the error of the fitted weights for different spectral features and noise levels and propose a framework to study local structures semi-quantitatively by using binary mixtures of FEFF9-simulated standards.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Robust Automatic EXAFS First-Shell Fits

Extended X-ray absorption fine structure (EXAFS) is a widely used technique for atomic structure determination. Fourier transformation connects EXAFS in k space and R space. However, determining the appropriate k-range for the transformation can be challenging, but critical for the first-shell fit. In this study, we present an automatic method to determine the k-range using the Larch package and a Python program. The first step is to estimate spectral noise across a series of k-ranges with a fixed minimum value and identify the optimal maximum value in the k-range (k max ). The k max is determined by an empirical noise threshold that marks the point where the noise level in the Fourier transformed spectrum changes dramatically. Using the obtained k max value, the first shell is modeled to determine the minimum k value (k min ) by optimizing the background function through alignment of the spectrum with theory. The optimal k min corresponds to the point of the minimum R-factor, which quantifies the difference between the experimental and fitted spectrum. Our method was tested on various typical datasets and yielded suitable k-ranges for Fourier transformation and accurate first-shell fits. This approach helps avoid unreliable, irreproducible data analysis, especially for noisy data from diluted samples, and enables robust automatic first-shell EXAFS fitting.

EXAFS analysis↗

Interpolating moving least-squares methods for fitting potential energy surfaces : improving efficiency via local approximants.

The local interpolating moving least-squares (IMLS) method for constructing potential energy surfaces is investigated. The method retains the advantageous features of the IMLS approach in that the ab initio derivatives are not required and high degree polynomials can be used to provide accurate fits, while at the same time it is much more efficient than the standard IMLS approach because the least-squares solutions need to be calculated only once at the data points. Issues related to the implementation of the local IMLS method are investigated and the accuracy is assessed using HOOH as a test case. It is shown that the local IMLS method is at the same level of accuracy as the standard IMLS method. In addition, the scaling of the method is found to be a power law as a function of number of data points N,N{sup -q}. The results suggest that when fitting only to the energy values for a d-dimensional system by using a Qth degree polynomial the power law exponent q {approx} Q/d when the energy range fitted is large (e.g., E<100 kcal/mol for HOOH), and q>Q/d when the energy range fitted is smaller (E<30 kcal/mol) and the density of data points is higher. This study demonstrates that the local IMLS method provides an efficient and accurate means for constructing potential energy surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrostatic point charge fitting as an inverse problem: Revealing the underlying ill-conditioning

Atom-centered point charge (PC) model of the molecular electrostatics—a major workhorse of the atomistic biomolecular simulations—is usually parameterized by least-squares (LS) fitting of the point charge values to a reference electrostatic potential, a procedure that suffers from numerical instabilities due to the ill-conditioned nature of the LS problem. To reveal the origins of this ill-conditioning, we start with a general treatment of the point charge fitting problem as an inverse problem and construct an analytical model with the point charges spherically arranged according to Lebedev quadrature which is naturally suited for the inverse electrostatic problem. This analytical model is contrasted to the atom-centered point-charge model that can be viewed as an irregular quadrature poorly suited for the problem. This analysis shows that the numerical problems of the point charge fitting are due to the decay of the curvatures corresponding to the eigenvectors of LS sum Hessian matrix. In part, this ill-conditioning is intrinsic to the problem and is related to decreasing electrostatic contribution of the higher multipole moments, that are, in the case of Lebedev grid model, directly associated with the Hessian eigenvectors. For the atom-centered model, this association breaks down beyond the first few eigenvectors related to the high-curvature monopole and dipole terms; this leads to even wider spread-out of the Hessian curvature values. Using these insights, it is possible to alleviate the ill-conditioning of the LS point-charge fitting without introducing external restraints and/or constraints. Also, as the analytical Lebedev grid PC model proposed here can reproduce multipole moments up to a given rank, it may provide a promising alternative to including explicit multipole terms in a force field.

74 ATOMIC AND MOLECULAR PHYSICS↗

IMFIT: A FAST, FLEXIBLE NEW PROGRAM FOR ASTRONOMICAL IMAGE FITTING

I describe a new, open-source astronomical image-fitting program called IMFIT, specialized for galaxies but potentially useful for other sources, which is fast, flexible, and highly extensible. A key characteristic of the program is an object-oriented design that allows new types of image components (two-dimensional surface-brightness functions) to be easily written and added to the program. Image functions provided with IMFIT include the usual suspects for galaxy decompositions (Sérsic, exponential, Gaussian), along with Core-Sérsic and broken-exponential profiles, elliptical rings, and three components that perform line-of-sight integration through three-dimensional luminosity-density models of disks and rings seen at arbitrary inclinations. Available minimization algorithms include Levenberg-Marquardt, Nelder-Mead simplex, and Differential Evolution, allowing trade-offs between speed and decreased sensitivity to local minima in the fit landscape. Minimization can be done using the standard χ{sup 2} statistic (using either data or model values to estimate per-pixel Gaussian errors, or else user-supplied error images) or Poisson-based maximum-likelihood statistics; the latter approach is particularly appropriate for cases of Poisson data in the low-count regime. I show that fitting low-signal-to-noise ratio galaxy images using χ{sup 2} minimization and individual-pixel Gaussian uncertainties can lead to significant biases in fitted parameter values, which are avoided if a Poisson-based statistic is used; this is true even when Gaussian read noise is present.

79 ASTRONOMY AND ASTROPHYSICS↗

Improving the accuracy and resolution of neutron crystallographic data by three-dimensional profile fitting of Bragg peaks in reciprocal space

Neutron crystallography is a powerful technique for directly visualizing the locations of H atoms in biological macromolecules. This information has provided key new insights into enzyme mechanisms, ligand binding and hydration. However, despite the importance of this information, the application of neutron crystallography in biology has been limited by the relatively low flux of available neutron beams and the large incoherent neutron scattering from hydrogen, both of which contribute to weak diffraction data with relatively low signal-to-background ratios. A method has been developed to fit weak data based on three-dimensional profile fitting of Bragg peaks in reciprocal space by an Ikeda–Carpenter function with a bivariate Gaussian. When applied to data collected from three different proteins, three-dimensional profile fitting yields intensities with higher correlation coefficients (CC 1/2 ) at high resolutions, decreased R free factors, extended resolutions and improved nuclear density maps. Importantly, additional features are revealed in nuclear density maps that may provide additional scientific information. These results suggest that three-dimensional profile fitting will help to extend the capabilities of neutron macromolecular crystallography.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗