Results for “fracture monitoring” — Page 11

DOE OSTI2021

Characterization of damage processes in Montney siltstone under triaxial compression using acoustic emission and diagnostic imaging

SUMMARY Crack nucleation and rock failure processes in a fine-grained siltstone (Montney Formation) under triaxial compression are investigated using combined diagnostic techniques, including ultrasonic-wave measurement, acoustic-emission (AE) monitoring, computed tomography (CT) scanning, and thin-section imaging. The sample displays a weak-to-moderate inherent seismic anisotropy and noticeable stress-induced anisotropy prior to failure. No AE event was detected until the applied axial stress reached 95 per cent of the peak value. The signal-to-noise ratio is relatively low, however, and detectable AE events are more diffuse than those observed in highly brittle rocks. The AE locations correlate with a shear fracture zone imaged by CT scanning. AE moment-tensor analysis reveals that events with larger relative magnitudes are characterized by high volumetric (tensile or compressive) components, and the initiation of the failure zone is dominated by combined shear-tensile (ST) failure. Stress inversion of the AE events with high tensile components is in good agreement with the known applied stress. Microscopic imaging of thin sections from the failed sample shows that the failure zone is an en echelon structure consisting of a major fracture with branching micro and minor cracks. This failure mechanism is consistent with a ST source mechanism and is interpreted to be associated with the fine granular structure and mineral composition of Montney siltstone.

Jia, Suzie Q. (ORCID:0000000326496190)↗

DOE OSTI2024

Multi-functional cementitious materials with ultra-high damage tolerance and self-sensing ability

Cementitious materials having high damage tolerance and self-sensing ability are described herein. These materials may replace conventional concrete to serve as a major material component for infrastructure systems with greatly improved resistance to cracking, reinforcement corrosion, and other common deterioration mechanisms under service conditions, and prevents fracture failure under extreme events. These materials can also be used for the repair, retrofitting or rehabilitation of existing concrete structures or infrastructure systems. Furthermore, these materials may offer capacity for distributed and direct sensing of cracking, straining and deterioration with spatially continuous resolution wherever the material is located, without relying on installation of sensors. The present invention relates to multifunctional cementitious structural or infrastructure materials that integrate self-sensing with damage tolerance for improving safety, extending service life, and health monitoring of structures, components, and infrastructure systems.

Li, Mo↗

DOE OSTI2023

Formation and characterization of hydride rim structures in Zircaloy-4 nuclear fuel cladding tubes

Zirconium alloy tubes used as nuclear fuel cladding are subject to oxidation and subsequent hydrogen pickup during their long service in commercial light water reactors. The hydrogen picked up in the cladding can precipitate as a brittle hydride rim feature on the cladding outer surface. Here, to better understand the effect of hydride rims on the fracture behavior of stress-relieved zirconium alloy cladding tubes, a procedure to produce these rim-like structures has been developed and is described herein. Extensive characterization of the ‘as hydrided’ tubes is performed. The hydrogen charging apparatus consists of a tube furnace with a quartz chamber that is connected to a vacuum pump as well as a bottle of pure hydrogen gas. The charging station uses a static charge of hydrogen as opposed to a flowing gas. The chief advantage of this approach is the ability to monitor the pressure drop in the hydriding chamber and correlate this pressure drop to a known rate of hydrogen pickup in the cladding tube. It was found that the hydrogen partial pressure, metal temperature, and surface treatment all clearly played a role in whether a hydride rim was formed. Extensive characterization of the hydride rims shows they consist of needle like platelets of δ phase hydrides (ZrH1.66) oriented in the circumferential direction with a radial spacing of several microns in a sandwich-like structure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Joint Focal Mechanism Inversion Using Downhole and Surface Monitoring at the Decatur, Illinois, CO2 Injection Site

ABSTRACT The three-year CO2 injection period at the Illinois Basin - Decatur Project site (Decatur, Illinois, United States) produced a number of microseismic events distributed in very distinct spatiotemporal clusters with different orientations. Further characterization of the microseismicity encompasses the determination of the event source mechanisms. Initially, the microseismic monitoring network consisted solely of borehole sensors, but has been extended with surface sensors, thereby significantly improving the data coverage over the focal sphere. This article focuses on 23 events from the northernmost microseismic cluster (about 2 km from the injection point) and takes advantage of both, surface and downhole, recordings. The resulting strike-slip east–west-oriented focal planes are all consistent with the east–west orientation of the cluster in map view. The injection-related increase of pore pressure is far below the formation fracture pressure; however, small stress-field changes associated with the pore-pressure increase may reach as far as to the investigated cluster location. Monte Carlo modeling of the slip reactivation potential within this cluster showed that the observed maximum stress-field orientation of N068° is the optimum orientation for fault reactivation of the east–west-oriented cluster. Our results suggest that the east–west orientation of the investigated cluster is the main reason for its activation, even though the cluster is about 2 km away from the low-pressure injection point.

Geochemistry & Geophysics↗

DOE OSTI2026

Deep Learning and Photogrammetric Reconstruction for Automated Crack Detection and Dimensional Measurement in Mining Operations

Surface crack detection and dimensional measurement at active mining sites present significant safety and operational challenges. Manual inspection methods are labor-intensive, spatially incomplete, and expose personnel to hazardous environments, while existing automated approaches have been developed primarily for concrete civil infrastructure and have not been validated on the complex, variable surfaces characteristic of mining environments. This dissertation presents an automated pipeline that integrates deep learning semantic segmentation with Structure-from-Motion photogrammetry to detect surface cracks and measure their aperture, length, and vertical displacement from standard RGB imagery acquired during routine Uncrewed Aerial Vehicle (UAV) survey operations, without requiring additional sensor hardware or manual measurement. The pipeline combines a U-Net architecture with an EfficientNet-B0 encoder, pretrained on the SDNET2018 concrete crack dataset and fine-tuned on a mining-specific dataset spanning laboratory concrete specimens, coal refuse impoundment embankments, and post-blast limestone quarry benches. Photogrammetric reconstruction is performed using COLMAP Structure-from-Motion and Multi-View Stereo, with crack segmentation masks projected into the reconstructed point cloud to enable three-dimensional vertical displacement measurement through local plane fitting and bimodal surface detection. The pipeline was validated across 36 controlled laboratory specimens at three imaging distances and four vertical displacement levels, achieving aperture measurement RMSE of 0.047 cm and R² of 0.954, and vertical displacement RMSE of 0.140 cm and R² of 0.966, against independent caliper measurements. Field application at a coal refuse impoundment in southwestern Pennsylvania detected 71 crack components across the embankment crest, with a dominant longitudinal crack exhibiting aperture values reaching 28 cm and a 95th percentile vertical displacement of 35.53 cm, consistent in magnitude and spatial distribution with simultaneously acquired LiDAR-derived estimates. Application across four post-blast limestone quarry bench datasets in California successfully characterized blast-induced fracture networks at ground sampling distances ranging from 0.59 to 1.23 cm/pixel, with detected crack geometries physically consistent with observable surface conditions at each site. The results demonstrate that deep learning-based crack detection and photogrammetric measurement can be integrated into routine UAV inspection workflows at mining sites, providing repeatable, scalable, and quantitative crack characterization across surface types, crack scales, and displacement magnitudes not previously addressed in the literature. The pipeline requires no dedicated surveying equipment beyond the UAV platforms already deployed at mine sites for survey and monitoring purposes, supporting practical adoption within existing operational workflows.

Crack detection, Dimensional Measurement↗

DOE OSTI2020

Assessment of Grizzly Capabilities for Reactor Pressure Vessels and Reinforced Concrete Structures

Over the last several years, capabilities to simulate the progression and effects of degradation in critical structures in light water reactor (LWR) nuclear power plants have been under development in the Grizzly code. Age-related material degradation is important for a number of systems in LWRs, but the main focus for Grizzly development has been on reactor pressure vessels (RPVs) and concrete structures because of their central role and the difficulty of replacement of these structures if they are found to be degraded to an unacceptable degree. The capabilities for analyzing both RPVs and concrete structures in Grizzly have reached a point where the feature sets are sufficiently complete to perform credible analyses of those types of structures. Because of this, the emphasis has shifted from foundational development to assessing the accuracy of these modeling capabilities on representative problems of interest and on improving the physical basis of those models to improve their ability to predict the actual response of those structural systems. This report documents a first set of test cases that have been developed to assess the Grizzly code on real-world problems for these two types of structures. For RPVs, these test cases consist of a set of benchmark problems where Grizzly is compared to another code. For concrete structures, a set of models of experimental specimens designed to characterize the multidimensional swelling response of reinforced concrete members due to alkali-silica reaction (ASR) has been developed and compared with experimental results. Both the RPV and concrete test cases developed here are much more computationally intensive than the small regression tests that are used in the testing that Grizzly undergoes every time a proposed set of changes is made to ensure that those changes do not adversely affect previously established behavior. A system for regularly running these large problems to monitor the behavior of the code as it is developed has been instituted. While these test cases generally indicate good comparison with the benchmark results, they also indicate areas where further development is warranted.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

Variations in Bedrock and Vegetation Cover Modulate Subsurface Water Flow Dynamics of a Mountainous Hillslope

Abstract Predicting the hydrological response of watersheds to climate disturbances requires a detailed understanding of the processes connecting hillslopes and streams. Using a network of soil moisture and temperature sensors, electrical resistivity tomography monitoring, and a weather station we assess the above and below‐ground processes driving the hydrological response of a hillslope during snowmelt and summer monsoon. The transect covers bedrock and vegetation gradients, with a steep upper part characterized by shallow bedrock, and gentle lower part underlain by colluvium. The main vegetation cover is conifers on the upper, and grass and veratrum on the lower part. Combined with a simplified hydrological model, we show that the thin soil layer of the steep slope acts as a preferential flow path, leading to mostly shallow lateral flow, interrupted by vertical flow, mostly at tree locations, and likely facilitated by flow along fractures and roots. Vertical flow and upstream‐driven groundwater dynamics are prevailing at the colluvium, presenting a very different hydrological behavior compared to the upper part. These results show that subsurface structure and features have a strong control on the hydrological response of a hillslope and that those can create considerably varying hydrological dynamics across small spatial scales.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Microseismicity Modulation Due To Changes in Geothermal Production at San Emidio, Nevada, USA

Brief cessations of geothermal production can induce seismicity, a phenomenon that has drawn increasing attention in recent years. Such observations are rare, and the underlying mechanism requires careful analysis. In April 2022, a dense seismic and hydrologic monitoring system was deployed at the San Emidio geothermal field, Nevada, to accompany a planned power plant shutdown. Using the dense seismic array data, we detected and located ∼1,800 microseismic events (MSEs) and developed a high-resolution tomographic P-wave velocity model. We observed substantially increased microseismicity during shutdown. Most MSEs occurred on pre-existing normal faults, which are contained within extremely low-velocity zones that are likely damaged, fluid-filled, and hydraulically connected to nearby production wells. Hydrologic data show rapid fluid pressure increases of <60 kPa following the shutdown. We suggest that the cessation of production rapidly increased fluid pressures along pre-existing fault zones, activating critically stressed fault patches and fractures and producing microseismicity.

Guo, Hao [University of Wisconsin-Madison, WI (Uni↗

DOE OSTI2021

Well Stimulation Treatment in California: Evaluation of Disclosure Data, May 2015 – October 2019

In this document, disclosure data from 1,228 well stimulations occurring May 2015 to October 2019 in California are evaluated. This evaluation updates a previous study that was based on 618 well stimulations occurring May 2015 to June 2016 (Stringfellow, W.T., Camarillo, M.K., and Jordan, P. 2017, Status of Well Stimulation in California Since Implementation of SB-4 Regulations, Berkeley National Laboratory, Berkeley, CA). While the goal of the previous study was to provide a summary of information obtained since passage of California Senate Bill No. 4—Oil and Gas, the goal of the current evaluation is to provide a basis for studying chemical indicators that could potentially be used to detect aquifer contamination. We evaluate chemical indicators is a separate document using the data contained herein as well as data from monitoring wells located within oil fields. Compared with the data used by Stringfellow et al. 2017, the current evaluation is based on a more diverse data set. While the previous study contained data for only two oil fields with more than 30 well stimulations, the current data set contains four oil fields with more than 30 well stimulations, making these data more ideal for comparisons using statistical tests. More producers and a new oil field, Buena Vista Nose, are represented in the current data set. Some well stimulation practices remain relatively unchanged since the previous study. Well stimulation is mostly occurring in Kern County with the exception of a single well stimulation in Orange County. Almost all well stimulations are hydraulic fracturing. The current data set contains two acid fracturing treatments and one matrix acidizing treatment. The median number of chemicals added per well stimulation—excluding water and proppant—was previously 21; the number in the expanded data set is 20. Median water added per well stimulation was previously 89,000 gallons and is now 98,000 gallons. While this water use represents a 10% increase, water use for hydraulic fracturing in California is still lower than water use in other oil and gas fields. Chemical formulations appear to have shifted since the previous study. This shift may be related to a change in the predominant service company. We identified 26 chemicals for which the frequency of use has changed by more than 30%. The total number of chemicals used has also expanded. Previously, 178 unique chemicals were identified as being added to well stimulation fluids. The total number of unique chemicals is now 205. Analytical data available for base and recovered fluids has expanded. The number of base fluid samples has increased from 12 to 35 and the number of recovered fluid samples has increased from 1,078 to 2,166. The expanded data set is more ideal for an evaluation of indicator chemicals and comparisons across different formations. The analytical data for recovered fluid samples indicates that many ions, radioactive constituents, and organics are consistently observed, making these chemicals ideal for consideration as potential indicators of aquifer contamination.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Distributed Acoustic Sensing to Estimate the Permeability

Optical fiber in a borehole can be interrogated with distributed acoustic sensors (DAS) to capture fracture displacements with the potential to map surrounding fracture networks. We designed a laboratory experiment to test the capability of DAS to determine borehole flow characteristics, and we show that for the first time DAS can be used to remotely estimate permeability. Optical fiber was wrapped around a bead filled pipe and the pressure drop and flow velocity were measured to directly calculate permeability. A machine learning model using statistical features from continuous DAS estimated the bulk permeability. Fluid interactions with the permeable material demonstrate insufficient resolution using DAS amplitude-based measurements for estimating pressure drop to infer permeability. Variations in the spectral domain relate DAS measurements to the pressure drop and provide consistent permeability estimates. Resolution with DAS is sufficient to estimate permeability and provides a reliable method to monitor at depth in borehole conditions.

58 GEOSCIENCES↗

DOE OSTI2021

Temperature-responsive smart tracers for field-measurement of inter-well thermal evolution: Heterogeneous kinetics and field demonstration

Temperature-responsive smart tracers enable advanced warning of a “premature thermal breakthrough” and may therefore improve reservoir management and reduce financial risk. A successful calculation of inter-well fluid temperatures requires that temperature-dependent kinetics are known, which typically result from homogeneous batch reactor experiments. However, recent meso-scale field experiments at the Altona Field Laboratory involving fluid flow in a discretely-fractured reservoir suggest that silica-fluid interfaces may accelerate hydrolysis kinetics. Here, the Arrhenius parameters of phenyl acetate hydrolysis are investigated under heterogeneous reaction conditions in packed-bed column experiments. The breakthrough curve of the reaction product is compared to an inert reference tracer (carbon-cored nanoparticles). Temperatures experienced during field testing ranging from 10 to 40 °C were studied using a phosphate buffer solution to maintain a near-neutral pH, as found in the reservoir. The empirically-determined pre-exponential factor and activation energy values are subsequently used in a first-order kinetic model to improve calculations of effective reservoir temperatures for these meso-scale field tests. Here, the results suggest that hydrolysis reactions can directly monitor inter-well reservoir temperatures, but only if the influence of solid-fluid interactions are carefully accounted for.

15 GEOTHERMAL ENERGY↗

DOE OSTI2023

Utah FORGE: Optimization of a Plug-and-Perf Stimulation (Fervo Energy)

Information around the plug-and-perf treatment design at Utah FORGE by Fervo Energy. Objective and Purpose: - Develop a multistage hydraulic stimulation approach designed specifically to target the top three factors that control the technical and commercial viability of an EGS system: i) Achieving sufficient injectivity to support high cross-well flow rates ii) Distributing flow evenly across the wellbore and reservoir to maximize heat mining efficiency, ensure sustained heat transfer, and mitigate thermal breakthrough iii) Overcoming the effects of stress heterogeneity, stress shadowing, and variations in natural fracture properties during the stimulation treatment, leading to a more predictable stimulated reservoir volume and offset well placement - The following activities will be performed: i) Design, plan, and execute a multistage plug-and-perf stimulation treatment at a Fervo site with data acquisition and well testing activities aimed at addressing key technical aspects of the issues above ii) Perform data processing and interpretation of field results to translate the results form the Fervo site to a site-specific design at the Utah FORGE site iii) Design, plan, and execute a multistage plug-and-perf stimulation treatment design at the Utah FORGE site Methods and Approach: - Design a detailed data acquisition plan to maximize learning around: i) DFIT testing ii) Petrophysical logging, image logging iii) Permanent DAS/DTS fiber optic monitoring iv) Deep borehole microseismic monitoring v) Shallow borehole induced seismicity monitoring vi) Injection/production testing (RTA analysis, tracer testing) vii) Integrated numerical modeling and production forecasting

15 GEOTHERMAL ENERGY↗

DOE OSTI2023

Computed Tomography Scanning and Geophysical Measurements of the CarbonSAFE Seal Integrity Wells in the Illinois Basin

The U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) researchers in Morgantown, West Virginia, utilized computed tomography (CT) facilities and the Multi-Sensor Core Logger (MSCL) to evaluate the integrity of three cores (Geophysical Monitor #2 (GM2), Verification Well #1 (VW #1), and Wabash #1 for the Illinois Basin Carbon Storage Assurance Facility Enterprise (CarbonSAFE) efforts. This work was carried out in collaboration with the Illinois State Geological Survey (ISGS) as part of their efforts to analyze cores from two field locations, including the Illinois Basin-Decatur Project (IBDP) and second stage Illinois Industrial Carbon Capture and Storage (IL-ICCS) sites at Decatur, Illinois, and the Wabash CarbonSAFE project at the Wabash Valley Resources Integrated Gasification Combined Cycle plant in Terre Haut, Indiana. The results of this study are presented in several formats and are available online on the Energy Data eXchange (EDX). The rock characterization was conducted using non-destructive techniques, allowing for future analysis of the cores. While the equipment used did not provide direct visualization of shale pore space, it allowed for detection of fractures and discontinuities. Low resolution CT imagery with the NETL medical CT scanner was performed on the entire core. Qualitative analysis of the medical CT images, coupled with x-ray fluorescence (XRF), P-wave, and magnetic susceptibility measurements from the MSCL were utilized to identify areas of interest for further study as well as fractured zones. The ability to quickly identify key areas for more detailed study with higher resolution will save time and resources in future studies. The combination of methods used provided a multi-scale analysis of this core and provided both a macro and micro description of the core that is relevant for many subsurface energy-related examinations traditionally performed at NETL.

58 GEOSCIENCES↗

DOE OSTI2023

The role of international collaboration in the United States geologic disposal research program

Abstract. More than a decade ago, the United States disposal program discontinued all research activities focused on the unsaturated fractured tuff formation at Yucca Mountain as the geologic disposal site for spent fuel and high-level radioactive waste. A new research and development (R&D) program was initiated to provide a sound technical basis for alternative disposal options across clay, crystalline, and salt rocks. The goals of this broad program were (and still are) to (1) increase confidence in the robustness of generic disposal concepts, (2) develop the science and engineering tools needed to support disposal concept implementation, and (3) conduct R&D on the direct disposal of existing dual-purpose (storage and transportation) canisters. Recognizing the benefits of international collaboration toward the common goal of safely and efficiently managing the back end of the nuclear fuel cycle, the program emphasized international cooperation as an effective strategy for sharing information and knowledge. In a multi-laboratory effort coordinated by Lawrence Berkeley National Laboratory, the United States Department of Energy (DOE) program established formal and informal cooperation partnerships with several international initiatives and institutions and developed a number of collaborative R&D activities in important research areas, such as engineered barrier integrity, near-field perturbations, radionuclide transport, performance assessment, and methods for characterization and monitoring of engineered and natural barriers. This presentation gives an overview of these R&D activities, with a specific focus on activities that improve our current understanding of the coupled thermal–hydrological–mechanical–chemical (THMC) processes occurring in engineered and natural barriers. We start with a brief review of selected international collaboration initiatives and then describe a few specific collaboration projects. We focus specifically on such studies that use experimental data sets provided by international research cooperation for joint modeling work to increase confidence in performance-relevant predictions of coupled processes. Overall, the focus on international collaboration has allowed deep engagement of US researchers with the international waste management R&D community in terms of best practices, new scientific advances, state-of-the-art simulation tools, new monitoring and performance confirmation approaches, and lessons learned. The joint R&D with international researchers, worldwide sharing of knowledge and experience, and access to relevant data and experiments from a variety of host rocks have helped our researchers to significantly improve their understanding of the current technical basis for disposal in a range of potential host rock environments. International collaboration also provides ample opportunity for training and educating junior staff that are well suited to move the United States disposal research program forward into the next decades, a promising avenue for developing a next-generation workforce of disposal scientists.

Birkholzer, Jens T.↗

DOE OSTI2025

Utah FORGE: Triaxial Direct Shear Results - February 2025

This dataset contains results from nine triaxial direct shear tests conducted by Los Alamos National Laboratory on samples from FORGE Well 16A(78)-32. The primary objectives of this work were to determine the shear strength in both intact and residual states, evaluate dilation against displacement, assess permeability in relation to displacement, time, and normal stress, understand the relationship between aperture and normal stress, and monitor the effluent chemistry as a function of time. The data includes time-series measurements of stress, displacement, permeability, and effluent chemistry, with and without experimental dilution corrections. Additional materials include profilometry data, photographic documentation of the experimental setups and apparatus, and test notes. The dataset is organized into folders corresponding to each test, containing hydromechanical data, effluent chemistry measurements, and images. The hydromechanical data consists of detailed time-series records capturing parameters such as shear force, confining pressure, permeability, and temperature. Effluent chemistry data tracks fluid composition changes over time. Also included are conference papers, presentation slides, and a summary document outlining the experiments.

15 GEOTHERMAL ENERGY↗

DOE OSTI2023

Recent Developments in Hydrogeologic Applications for Strain Tensor Analyses

Changes in fluid pressure deform porous media and this effect occurs in a variety of hydrogeologic processes, from the change in storage during pumping or injection to fluctuations in water levels caused by barometric pressure. We have developed instruments for measuring small strains in porous media, and we have used the resulting strain data to evaluate well testing, hydraulic fracturing, manual loading at the ground surface, and ambient hydrologic processes, like rainfall and evaporation. A particularly important application is the use of strain tensor data measured at shallow depths to analyze well tests or hydraulic fractures conducted at much greater depths. An early demonstration of this technique was conducted at the North Avant Field north of Tulsa, Oklahoma, where Pennsylvanian sandstone creates a confined aquifer and oil reservoir at a depth of 530m. We have showed that the strains caused by injecting into the aquifer could be measured at a depth of 30m and used to evaluate the properties of the aquifer. We recently expanded the array of strainmeters at the North Avant Field by deploying three more instruments at shallow depth (30m) along with a deep instrument at 520m depth in the winter, 2021. The deep instrument is deployed in shale caprock slightly above the aquifer. To our knowledge, the deep strainmeter at the North Avant Field is the deepest strainmeter ever deployed and this required refining methods originally developed for shallow deployments. The instrument was lowered to depth on oil field tubing and cemented in place using techniques and materials developed for use in oil wells. Optical fiber used to communicate with the instrument was cemented in the annulus on the outside of tubing. This is significant because the techniques we used could readily be extended to greater depth, suggesting that strainmeters can be deployed over a wide range of depths for monitoring critical subsurface processes. For example, it suggests that strainmeters could be deployed through the caprock to monitor for leaks from underlying CO2 storage reservoirs. The strainmeter array at the North Avant Field has been used to characterize deformation during a series of injection tests in the spring and summer, 2021. All the new strainmeters respond to pumping, and the strainmeters we installed earlier also responded. To our knowledge, this is the first application of well testing in a deep aquifer that was monitored by an array of strainmeters—our earlier work used strainmeters at a single location. We are currently analyzing the strain data using an analytical solution, a proxy-based Bayesian inversion algorithm, and other methods. Strainmeter data has also been used to characterize periodic pumping tests by us and Riley Blais. A periodically varying pumping rate causes both hydraulic head and strain signals that vary with the same period as the pumping. The peaks and troughs of the head in monitoring wells lag behind the peaks and troughs of the head in the pumping well, and this lag time increases with distance from the pumping well. The lag time of the pressure and the distance to the monitoring well can be used in a simple analysis to estimate the hydraulic diffusivity of the aquifer. The lag time determined from strain data can be used to estimate aquifer properties using the same analysis that works for the pressure only for strain data measured at particular locations. That is because the strain field in a confining unit advances upward, laterally and then downward even though the pressure in the underlying aquifer only advances laterally, according to our recent simulations. We have field data showing that a small periodic signal superimposed on an injection rate at the North Avant Field will create a periodic strain signal at shallow strainmeters. The field data and the recent simulations suggest that including a periodic component to injection or pumping and then monitoring the resulting strain signal could be a way to monitor the subsurface.

Murdoch, Larry↗

DOE OSTI2023

Recent Developments in Hydrogeologic Applications for Strain Tensor Analyses

Changes in fluid pressure deform porous media and this effect occurs in a variety of hydrogeologic processes, from the change in storage during pumping or injection to fluctuations in water levels caused by barometric pressure. We have developed instruments for measuring small strains in porous media, and we have used the resulting strain data to evaluate well testing, hydraulic fracturing, manual loading at the ground surface, and ambient hydrologic processes, like rainfall and evaporation. A particularly important application is the use of strain tensor data measured at shallow depths to analyze well tests or hydraulic fractures conducted at much greater depths. An early demonstration of this technique was conducted at the North Avant Field north of Tulsa, Oklahoma, where Pennsylvanian sandstone creates a confined aquifer and oil reservoir at a depth of 530m. We have showed that the strains caused by injecting into the aquifer could be measured at a depth of 30m and used to evaluate the properties of the aquifer. We recently expanded the array of strainmeters at the North Avant Field by deploying three more instruments at shallow depth (30m) along with a deep instrument at 520m depth in the winter, 2021. The deep instrument is deployed in shale caprock slightly above the aquifer. To our knowledge, the deep strainmeter at the North Avant Field is the deepest strainmeter ever deployed and this required refining methods originally developed for shallow deployments. The instrument was lowered to depth on oil field tubing and cemented in place using techniques and materials developed for use in oil wells. Optical fiber used to communicate with the instrument was cemented in the annulus on the outside of tubing. This is significant because the techniques we used could readily be extended to greater depth, suggesting that strainmeters can be deployed over a wide range of depths for monitoring critical subsurface processes. For example, it suggests that strainmeters could be deployed through the caprock to monitor for leaks from underlying CO2 storage reservoirs. The strainmeter array at the North Avant Field has been used to characterize deformation during a series of injection tests in the spring and summer, 2021. All the new strainmeters respond to pumping, and the strainmeters we installed earlier also responded. To our knowledge, this is the first application of well testing in a deep aquifer that was monitored by an array of strainmeters—our earlier work used strainmeters at a single location. We are currently analyzing the strain data using an analytical solution, a proxy-based Bayesian inversion algorithm, and other methods. Strainmeter data has also been used to characterize periodic pumping tests by us and Riley Blais. A periodically varying pumping rate causes both hydraulic head and strain signals that vary with the same period as the pumping. The peaks and troughs of the head in monitoring wells lag behind the peaks and troughs of the head in the pumping well, and this lag time increases with distance from the pumping well. The lag time of the pressure and the distance to the monitoring well can be used in a simple analysis to estimate the hydraulic diffusivity of the aquifer. The lag time determined from strain data can be used to estimate aquifer properties using the same analysis that works for the pressure only for strain data measured at particular locations. That is because the strain field in a confining unit advances upward, laterally and then downward even though the pressure in the underlying aquifer only advances laterally, according to our recent simulations. We have field data showing that a small periodic signal superimposed on an injection rate at the North Avant Field will create a periodic strain signal at shallow strainmeters. The field data and the recent simulations suggest that including a periodic component to injection or pumping and then monitoring the resulting strain signal could be a way to monitor the subsurface.

Murdoch, Larry↗

DOE OSTI2025

Transportability of exogenous microbial community correlates with interwell connectivity in deep aquifers

Subsurface resource engineering operations often utilize continuous injection of externally-sourced water into geological reservoirs for formation pressure maintenance, resource recovery or energy/waste storage. Such injected water generally contains naturally occurring microbes. Little is known, however, about how the injectate microbes transport through geological media as a community, how such transportability is affected by injector-producer connectivity, and whether such knowledge can be utilized for flowpath characterization. In this study, we analyzed daily-to-weekly timeseries microbial community data from the injected- and produced-fluids of a ten-month flow test at a deep, well-characterized engineered aquifer. We found that the injectate microbial community was distinct from the indigenous community at the amplicon sequence variant (ASV) level, and that the transportability of injectate community towards a given producer, quantified by an “nASV-Overlap” metric we propose, had strong and significant positive correlation with known injector-producer connectivities at our site. This suggests that the better the connectivity, the higher the probability for more injectate species to flow through the interwell region and arrive at a producer. Because interwell connectivity is an important yet usually unknown parameter in subsurface resource engineering, such correlation in turn points to nASV-Overlap as a useful indicator of interwell connectivity for aquifer characterization and long-term monitoring. Based on our findings, an nASV-Overlap-based microbial tracing approach was developed for characterizing and monitoring the relative connectivities across multiple producers with a given injector. A side-by-side comparison between the new nASV-Overlap approach and traditional artificial tracer methods is presented, and their respective strengths and limitations are discussed.

Deep biosphere↗