Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Friction behavior of silicon in contact with titanium, nickel, silver and copper

Sliding friction experiments are conducted with the semiconductor silicon in contact with the metals titanium, nickel, copper, and silver. Sliding is on the (111) plane of single-crystal silicon in the 112 crystallographic direction both in dry and lubricated (mineral oil) sliding. The friction coefficient in dry sliding is controlled by adhesion and the surface chemical activity of the metal. The more active the metal the stronger the adhesion and the higher the friction. In lubricated sliding the lubricant absorbs to the surfaces and reduces the importance of metal chemical effects. In lubricated sliding, silicon ceases to behave in a brittle manner and undergoes plastic deformation under load.

Mishina, H.↗

An Experimental Study of Turbulent Skin Friction Reduction in Supersonic Flow Using a Microblowing Technique

A new turbulent skin friction reduction technology, called the microblowing technique has been tested in supersonic flow (Mach number of 1.9) on specially designed porous plates with microholes. The skin friction was measured directly by a force balance and the boundary layer development was measured by a total pressure rake at the tailing edge of a test plate. The free stream Reynolds number was 1.0(10 exp 6) per meter. The turbulent skin friction coefficient ratios (C(sub f)/C(sub f0)) of seven porous plates are given in this report. Test results showed that the microblowing technique could reduce the turbulent skin friction in supersonic flow (up to 90 percent below a solid flat plate value, which was even greater than in subsonic flow).

Hwang, Danny P.↗

Measurements of Skin Friction of the Compressible Turbulent Boundary Layer on a Cone with Foreign Gas Injection

Measurements of average skin friction of the turbulent boundary layer have been made on a 15deg total included angle cone with foreign gas injection. Measurements of total skin-friction drag were obtained at free-stream Mach numbers of 0.3, 0.7, 3.5, and 4.7 and within a Reynolds number range from 0.9 x 10(exp 6) to 5.9 x 10(exp 6) with injection of helium, air, and Freon-12 (CCl2F2) through the porous wall. Substantial reductions in skin friction are realized with gas injection within the range of Mach numbers of this test. The relative reduction in skin friction is in accordance with theory-that is, the light gases are most effective when compared on a mass flow basis. There is a marked effect of Mach number on the reduction of average skin friction; this effect is not shown by the available theories. Limited transition location measurements indicate that the boundary layer does not fully trip with gas injection but that the transition point approaches a forward limit with increasing injection. The variation of the skin-friction coefficient, for the lower injection rates with natural transition, is dependent on the flow Reynolds number and type of injected gas; and at the high injection rates the skin friction is in fair agreement with the turbulent boundary layer results.

Pappas, Constantine C.↗

Verification of Anisotropic Mesh Adaptation for Turbulent Simulations over ONERA M6 Wing

Unstructured anisotropic mesh adaptation is known to be an efficient way to control discretization errors in Computational Fluid Dynamics (CFD) simulations. Method verification is required to provide the confidence for routine use in production analysis. The current work aims at verification of anisotropic mesh adaptation for RANS simulations over the ONERA M6 wing. The present verification study is performed using four different flow solvers, three different implementations of the metric field, and three mesh mechanics packages. Two of the flow solvers use stabilized finite-element discretizations (FUN3D-SFE and GGNS), one uses finite-volume discretization (FUN3D-FV), and the last one uses mixed finite-volume and finite element discretizations (Wolf). The mesh adaptation is based on an error estimator that aims to control the quadratic error term in the linear interpolation of Mach number. Two sets of adaptations were performed; the first one controls the interpolation error in L2 norm and the second one controls the interpolation error in L4 norm. Convergence studies were performed on the forces and the pitching moment using all four solvers, and the results are compared with previously verified convergence studies on fixed (nonadapted) meshes. Both forces and pitching moment on adapted meshes are found to be converging to the fine mesh values faster than those on fixed meshes. In addition to forces and moments, convergence of surface pressure and skin friction coefficients at various measurement locations on the wing are also presented. Adapted-mesh surface pressure distributions agree with the fine fixed mesh pressure distributions. Adapted-mesh skin friction distributions contain high frequency noise with mean values approaching the fixed mesh pressure skin friction distributions.

Aravind Balan↗

Effects of fluid inertia and turbulence on force coefficients for squeeze film dampers

The effects of fluid inertia and turbulence on the force coefficients of squeeze film dampers are investigated analytically. Both the convective and the temporal terms are included in the analysis of inertia effects. The analysis of turbulence is based on friction coefficients currently found in the literature for Poiseuille flow. The effect of fluid inertia on the magnitude of the radial direct inertia coefficient (i.e., to produce an apparent added mass at small eccentricity ratios, due to the temporal terms) is found to be completely reversed at large eccentricity ratios. The reversal is due entirely to the inclusion of the convective inertia terms in the analysis. Turbulence is found to produce a large effect on the direct damping coefficient at high eccentricity ratios. For the long or sealed squeeze film damper at high eccentricity ratios, the damping prediction with turbulence included is an order of magnitude higher than the laminar solution.

Andres, L. S.↗

Determination of general relations for the behavior of turbulent boundary layers

An analysis has been made of a considerable amount of data for turbulent boundary layers along wings and bodies of various shapes in order to determine the fundamental variables that control the development of turbulent boundary layers. It was found that the type of velocity distribution in the boundary layer could be expressed in terms of a single parameter. This parameter was chosen as the ratio of the displacement thickness to the momentum thickness of the boundary layer. The variables that control the development of the turbulent boundary layer apparently are: (1) the ratio of the nondimensional pressure gradient, expressed in terms of the local dynamic pressure outside the boundary layer and boundary-layer thickness, to the local skin-friction coefficient and (2) the shape of the boundary layer. An empirical equation has been developed in terms of these variables that, when used with the momentum equation and the skin-friction relation, makes it possible to trace the development of the turbulent boundary layer to the separation point.

Von Doenhoff, Albert E↗

Resistance to Sliding on Atomic Scales

The structure and stability of agglomerates of micron-sized particles is determined by the mechanical properties of the individual contacts between the constituent particles. In this paper we study the possibility of aggregate rearrangements by sliding. Since the contacts between (sub)micron particles are only a few hundred atoms in diameter, processes on atomic levels will play the dominating roll. We study a theoretical model of sliding friction for surfaces that are either flat or contain steps in their grids. The results show that sliding over flat surfaces may produce a large range of friction coefficients, including zero if the adhesive forces are small compared to the binding forces inside a body. However, both grid alignment and steps in the surface will lead to high values for friction. These processes combined virtually eliminate the possibility of sliding in a collision of two (sub)micron sized particles at velocities low enough for sticking to occur. On the other hand we show that in collisions between aggregates sliding may be an important factor for energy dissipation and compaction.

Dominik, C.↗

MoS2-Filled PEEK Composite as a Self-Lubricating Material for Aerospace Applications

At BAM, several projects were conducted in the past years dealing with the tribological properties of friction couples at cryogenic temperature and in vacuum environment. Promising candidates for vacuum application are MoS2-filled PEEK/PTFE composites, which showed a friction coefficient as low as 0.03 in high vacuum. To complete the tribological profile of these composites, further tests were performed in ultra-high vacuum (UHV) at room temperature. In this paper, friction and stick slip behavior, as well as outgassing characteristics during the test are presented.

Theiler, Geraldine↗

Nacelle design

The external cowlings of engine nacelles on large turbofan powered aircraft are good candidates for application of natural laminar flow. These nacelles usually have shorter characteristic lengths than other candidate surfaces such as wings and fuselages and therefore have lower characteristic Reynolds numbers. A conceptive figure of the natural flow nacelle (NLF) is shown. On the typical nacelle the flow accelerates to a curvature induced velocity peak near the lip and then decelerates over the remainder of the nacelle length. Transition occurs near the start of the deceleration, so turbulent flow with high friction coefficient exists over most of the nacelle length. On the other hand, the NLF nacelle is contoured to have an accelerating flow over most of its length, so transition is delayed, and a relatively lower friction drag exists over most of the nacelle. The motivation for development of the LFN is a potential 40 to 50 percent reduction in nacelle friction drag.

Faust, G. K.↗

Influence of low temperatures of friction and wear

A brief review of studies on low-temperature friction are briefly reviewed. A facility and technique for studying friction both in air and in vacuum at temperatures of +20 and -190 C is described. Results of a wear study of structural steels operating together with chromium steel are presented. It is shown that reduction of the test temperature in vacuum leads in certain cases to marked increase of the wear magnitude and friction coefficient. This is associated not only with the general change of the mechanical properties of the materials but also with the influence of temperature reduction on the hardening and structural formation taking place in the surface layers during friction.

Udovenko, V. F.↗

Gimbal Bearing Friction in the SLS Core Stage Thrust Vector Control System

The Space Launch System (SLS) Core Stage Thrust Vector Control (TVC) system is comprised of eight mechanical feedback Shuttle heritage Type III TVC actuators that vector the four Shuttle heritage RS-25 engines about a Shuttle heritage gimbal block/bearing. The MSFC Controls community has long regarded gimbal friction to be a negligible effect on the overall control of gimbaled RS-25 engines. This is corroborated by Space Shuttle test and flight data that does not appear to show degraded effects, nor limit cycling at the end of the shuttle flight. For this reason, friction was not expected to be a driving factor of performance and control of the reused RS-25 engines aboard the SLS. However, after test data showed a large shift in frequency behavior and a highly damped step-response in the time series, there was further investigation into what could have caused this behavior. Heritage friction models used in previous gimbal and ball bearings were evaluated such as Coulomb, Dahl and LuGre, but the single degree of freedom friction models alone were not enough to explain the behavior and shifts seen in the test data. This paper presents the additional findings and modeling efforts regarding friction on the RS-25 engines. Using the Two Actuator Operational Simulation (TAOS), the difference from modeling separate friction degrees of freedom to coupled degrees of freedom was investigated to deduce the effects of one axis’s movement on the other. Next, due to the vibration environment, a modified LuGre model has been proposed that adds an additional term to decrease the friction coefficient at low engine velocity amplitudes. Lastly, the addition of the stiffness in each half of the gimbal bearing has increased modeling fidelity by also adding the effect on the gimbal bearing bending in compliance to both the friction torque on the surface of the gimbal bearing and the actuator force that is forcing the engine in a specified direction. Through these effects, the time and frequency domain behavior seen in test can be characterized accurately.

Friction↗

Gimbal Bearing Friction in the SLS Core Stage Thrust Vector Control System

The Space Launch System (SLS) Core Stage Thrust Vector Control (TVC) system is comprised of eight mechanical feedback Shuttle heritage Type III TVC actuators that vector the four Shuttle heritage RS-25 engines about a Shuttle heritage gimbal block/bearing. The MSFC Controls community has long regarded gimbal friction to be a negligible effect on the overall control of gimbaled RS-25 engines. This is corroborated by Space Shuttle test and flight data that does not appear to show degraded effects, nor limit cycling at the end of the shuttle flight. For this reason, friction was not expected to be a driving factor of performance and control of the reused RS-25 engines aboard the SLS. However, after test data showed a large shift in frequency behavior and a highly damped step-response in the time series, there was further investigation into what could have caused this behavior. Heritage friction models used in previous gimbal and ball bearings were evaluated such as Coulomb, Dahl and LuGre, but the single degree of freedom friction models alone were not enough to explain the behavior and shifts seen in the test data. This paper presents the additional findings and modeling efforts regarding friction on the RS-25 engines. Using the Two Actuator Operational Simulation (TAOS), the difference from modeling separate friction degrees of freedom to coupled degrees of freedom was investigated to deduce the effects of one axis’s movement on the other. Next, due to the vibration environment, a modified LuGre model has been proposed that adds an additional term to decrease the friction coefficient at low engine velocity amplitudes. Lastly, the addition of the stiffness in each half of the gimbal bearing has increased modeling fidelity by also adding the effect on the gimbal bearing bending in compliance to both the friction torque on the surface of the gimbal bearing and the actuator force that is forcing the engine in a specified direction. Through these effects, the time and frequency domain behavior seen in test can be characterized accurately.

Friction↗

Some effects of composition on friction and wear of graphite-fiber-reinforced polyimide liners in plain spherical bearings

Oscillating, plain spherical bearings with graphite-fiber-reinforced polyimide (GFRPI) liners were tested for friction and wear from 25 to 315 C. A condensation polymer was compared with an addition polymer, and a high-modulus fiber was compared with a lower cost, low-modulus fiber. All polymer-fiber combinations gave friction coefficients from 0.05 to 0.18 and low wear. Adding CdO and CdI2 reduced the wear of degassed bearings in dry air. These additives were not needed when the bearing liners contained adsorbed moisture. Although, at 25 C, MoS2 reduced the friction and wear of the base composite at unit loads above 70,000,000 N/m squared (10,000 psi), it had no beneficial effect at lighter loads.

Sliney, H. E.↗

Experimental Investigation of a Model of a Two-Stage Turboblower

In the present paper an investigation is made of two stages of a multistage turboblower having a vaneless diffuser behind the impeller and guide vanes at the inlet to the nest stage. The method employed was that of investigating the performance of the successive elements of the blower (the impeller, vaneless diffuser, ets.) whereby the kinematics of the flow through the blower could be followed and the pressure at the different points computed. The character of the flow and the physical significance of the loss coefficients could thereby be determined so as to secure the best agreement of the computed with the actual performance of the blower. Since the tests were carried out for various delivery volumes, the dependence of the coefficients on a number of factors (angle of attack, velocities, etc.) could be obtained. The distribution of the losses that occur during the transformation of dynamic pressure at the impeller exit into static pressure could be found and likewise the range within which the friction coefficient varies in the vaneless diffuser. With the aid of factors having a certain physical significance, the centrifugal blower could be computed on the basis of a more or less schematical consideration of the phenomena occuring during the air flow through it, and the use of arbitrary factors and recourse to the geometrical similtude law thus avoided. The present investigation largely summarizes all the previous work af the CHI Blower Section on the different elements of a centrifugal blower. Some considerations on the analysis of model test data for application to full-scale are presented in the appendix.

Dovjik, s.↗

Neotectonics of Asia: Thin-shell finite-element models with faults

As India pushed into and beneath the south margin of Asia in Cenozoic time, it added a great volume of crust, which may have been (1) emplaced locally beneath Tibet, (2) distributed as regional crustal thickening of Asia, (3) converted to mantle eclogite by high-pressure metamorphism, or (4) extruded eastward to increase the area of Asia. The amount of eastward extrusion is especially controversial: plane-stress computer models of finite strain in a continuum lithosphere show minimal escape, while laboratory and theoretical plane-strain models of finite strain in a faulted lithosphere show escape as the dominant mode. We suggest computing the present (or neo)tectonics by use of the known fault network and available data on fault activity, geodesy, and stress to select the best model. We apply a new thin-shell method which can represent a faulted lithosphere of realistic rheology on a sphere, and provided predictions of present velocities, fault slip rates, and stresses for various trial rheologies and boundary conditions. To minimize artificial boundaries, the models include all of Asia east of 40 deg E and span 100 deg on the globe. The primary unknowns are the friction coefficient of faults within Asia and the amounts of shear traction applied to Asia in the Himalayan and oceanic subduction zones at its margins. Data on Quaternary fault activity prove to be most useful in rating the models. Best results are obtained with a very low fault friction of 0.085. This major heterogeneity shows that unfaulted continum models cannot be expected to give accurate simulations of the orogeny. But, even with such weak faults, only a fraction of the internal deformation is expressed as fault slip; this means that rigid microplate models cannot represent the kinematics either. A universal feature of the better models is that eastern China and southeast Asia flow rapidly eastward with respect to Siberia. The rate of escape is very sensitive to the level of shear traction in the Pacific subduction zones, which is below 6 MPa. Because this flow occurs across a wide range of latitudes, the net eastward escape is greater than the rate of crustal addition in the Himalaya. The crustal budget is balanced by extension and thinning, primarily within the Tibetan plateau and the Baikal rift. The low level of deviation stresses in the best models suggests that topographic stress plays a major role in the orogeny; thus, we have to expect that different topography in the past may have been linked with fundamentally different modes of continental collision.

Kong, Xianghong↗

Large-scale landslide simulations: Global deformation, velocities and basal friction

The cause of the apparent small friction exhibited by long runout landslides has long been speculated upon. In an attempt to provide some insight into the matter, this paper describes results obtained from a discrete particle computer simulation of landslides composed of up to 1,000,000 two-dimensional discs. While simplified, the results show many of the characteristics of field data (the volumetric effect on runout, preserved strata, etc.) and with allowances made for the two-dimensional nature of the simulation, the runouts compare well with those of actual landslides. The results challenge the current view that landslides travel as a nearly solid block riding atop a low friction basal layer. Instead, they show that the mass is completely shearing and indicate that the apparent friction coefficient is an increasing function of shear rate. The volumetric effect can then be understood. With all other conditions being equal, different size slides appear to travel with nearly the same average velocity; however, as the larger landslides are thicker, they experience smaller shear rates and correspondingly smaller frictional resistance.

Campbell, Charles S.↗

Sliding seal materials for adiabatic engines

The sliding friction coefficients and wear rates of promising carbide, oxide, and nitride materials were measured under temperature, environmental, velocity, loading conditions that are representative of the adiabatic engine environment. In order to provide guidance needed to improve materials for this application, the program stressed fundamental understanding of the mechanisms involved in friction and wear. Microhardness tests were performed on the candidate materials at elevated temperatures, and in atmospheres relevant to the piston seal application, and optical and electron microscopy were used to elucidate the micromechanisms of wear following wear testing. X-ray spectroscopy was used to evaluate interface/environment interactions which seemed to be important in the friction and wear process. Electrical effects in the friction and wear processes were explored in order to evaluate the potential usefulness of such effects in modifying the friction and wear rates in service. However, this factor was found to be of negligible significance in controlling friction and wear.

Lankford, J.↗

The effect of prolonged exposure to 750 C air on the tribological performance of PM212

The effect of prolonged exposure to 750 C air on the tribological performance and dimensional stability of PM212, a high temperature, self-lubricating composite, is studied. PM212, by weight, contains 70 percent metal-bonded Cr3C2, 15 percent BaF2/CaF2 eutectic, and 15 percent silver. Rub blocks were fabricated from PM212 by cold isostatic pressing followed by sintering. Prior to tribo-testing, the rub blocks were exposed to 750 C air for periods ranging from 100 to 1000 hours. Then, the rub blocks were slid against nickel-based superalloy disks in a double-rub-block tribometer in air under a 66 N load at temperatures from 25 to 750 C with a sliding velocity of 0.36 m/s. Unexposed rub blocks were tested for baseline comparison. Friction coefficients ranged from 0.24 to 0.37 for the unexposed rub blocks and from 0.32 to 0.56 for the exposed ones. Wear for both the composite blocks and superalloy disks was typically in the moderate to low range of 10(exp -5) to 10(exp -6) mm(exp 3)/N-m. Friction and wear data were similar for the rub blocks exposed for 100, 500, and 1000 hours. Prolonged exposure to 750 C air increased friction and wear of the PM212 rub blocks at room temperature, but their triboperformance remained unaffected at higher temperatures, probably due to the formation of lubricious metal oxides. Dimensional stability of the composite was studied by exposing specimens of varying thicknesses for 500 hours in air at 750 C. Block thicknesses were found to increase with increased exposure time until steady state was reached after 100 hours of exposure, probably due to oxidation.

Bemis, Kirk↗