Search NASA⌕ Search

SEARCH · Search NASA

Results for “fusion experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Pellet-Injector Technology—Brief History and Key Developments in the Last 25 Years

High-speed injection of solid fuel was first proposed in 1954 as a possible solution to the problem of transporting fresh fuel across the confining magnetic fields into the plasma of a fusion reactor. While it took a few decades, the use of cryogenic pellets (typically H 2 and D 2 ) on fusion experiments became common place; most tokamaks and stellarators are now equipped with a pellet injector(s). These devices operate at low temperatures (~10 to 20 K) and most often use a simple light gas gun to accelerate macroscopic-size pellets (~0.4- to 6-mm diameter) to speeds of ~100 to 1000 m/s. Before the advantages of pellet injection from the magnetic high-field side (HFS) of a tokamak were recognized in 1997, development focused on increasing the pellet speed to achieve deeper plasma penetration and higher fueling efficiency. The HFS injection technique typically dictates slower pellets (~100 to 300 m/s) to survive transport through the curved guide tubes that route the pellets to the plasma from the inside wall of the device. Two other key operating parameters for plasma fueling are the pellet-injection repetition rate and time duration—a single pellet is adequate for some experiments and a steady-state injection rate of up to ~50 Hz is appropriate for others. In addition to plasma fueling, cryogenic pellets have often been used for particle transport and impurity studies in fusion experiments (most often with neon pellets). During the past two decades, a few new applications for cryogenic pellets have been developed and used successfully in plasma experiments: (1) one for edge-localized mode mitigation, (2) one for plasma disruption mitigation (requires large pellets that are shattered before injection into the plasma), and (3) another in which pure argon pellets are used to trigger runaway electrons in the plasma for scientific studies. Here in this paper, a brief history and the key developments in this technology during the past 25 years are presented and discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Predictive Capabilities, Analysis and Experiments for Fusion Nuclear Science and Plasma Chamber Research

UCLA led the efforts of the US on Fusion Nuclear Science and Technology (FNST) for the past 35 years and is the recognized leader of FNST research. UCLA research focuses on identifying and characterizing the key FNST issues with high scientific content, performing pioneering experiments and advancing modelling capabilities, and has led many pioneering domestic and international studies on FNST that greatly advanced the FNST field. Examples of major achievements include our leadership and research work in: FINESSE: Seminal contribution to defining the FNST issues and research approach APEX: High power density concepts including free surface liquid walls and divertors FNSF/VNS: Need for and definition of FSNF conceived and pioneered by UCLA US ITER Test Blanket Program: Defined the test program with international community and options for US participation US-JA JUPITER and TITAN research collaborations: First of a kind research on Molten salt MHD and other advanced functional materials UCLA-EUROfusion collaboration: construction of a first-of-a-kind multiple effect LM-MHD-Thermofluid test facility The achievements and the associated publications during the current grant period of 2/1/2017 to 01/31/2019 are summarized in this final report for the following research areas: First experiments on a First-of-a-Kind Multiple-effect Facility in Liquid Metal MHD Research Self-Generated Stress Evolutions in Ceramic Breeder Material System Thermomechanics Integrated Model for Tritium Transport and Permeation Predictions FESS Liquid Wall Study The people working on the project during this period are listed in Section III. There is no unexpended funds at the final budget period.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High Performance Equilibrium Solvers for Integrated Magnetic Fusion Simulations

With the funding provided by this award, we developed numerical codes for the study of magnetically confined plasmas for fusion applications. Accordingly, our work can be divided into two separate categories: 1) the design and analysis of novel numerical methods providing high accuracy and high efficiency; 2) the study of the equilibrium and stability of magnetically confined plasmas with some of these numerical codes, as well as the study of the nature of the turbulent behavior which may arise in the presence of instabilities. We first developed new numerical schemes based on integral equation methods for the computation of steady-state magnetic configurations in fusion experiments, providing high accuracy for the magnetic field and its derivatives, which are required for stability and turbulence calculations. We employed different integral formulations depending on the application of interest: axisymmetric or non-axisymmetric equilibria, force-free or magnetohydrodynamic equilibria, fixed-boundary equilibria or free-boundary equilibria. While efficient, these methods do not yet apply to plasma boundaries which are not smooth, a situation which is fairly common in magnetic confinement experiments. To address this temporary weakness, we also constructed a new steady-state solver based on the Hybridizable Discontinuous Galerkin (HDG) method, which provides full geometric flexibility. In addition to these numerical tools focused on steady-states, we also contributed to the improvement of the speed and accuracy of codes simulating the plasma dynamics of fusion plasmas, by developing a novel velocity space representation for the efficient solution of kinetic equations, which most accurately describe the time evolution of hot plasmas in fusion experiments. Using the tools discussed above, we studied several questions pertaining to the equilibrium and stability of magnetically confined plasmas. In particular, we derived a new simple model for axisymmetric devices called tokamaks, to predict how elongated a fusion plasma can be before it becomes unstable and collapses. We also looked at the effect of the shape of the outer plasma surface on key properties of the steady-state magnetic configurations, and how these properties impact turbulence in fusion plasmas, and the corresponding transport of momentum. Likewise, we studied the role of large localized flows on the steady-state magnetic configurations, and how they may influence plasma stability and turbulence. Non-axisymmetric steady-state magnetic configurations are inherently more complex than axisymmetric steady-state configurations, and the subject of ongoing controversies regarding the regularity of the equations determining such steady-states, and their solutions. Implementing an existing NYU code in a new geometry, we studied the nature of the singularity of the solutions observed in the code, and methods to eliminate them. Our main conclusion is that by appropriately tailoring the plasma boundary, it is possible to eliminate the singularities otherwise appearing in our simulations, and to obtain steady-states which appear to be smooth. To gain further insights on incompletely understood turbulence phenomena, we proposed a new reduced model capturing most of these phenomena, which is simple enough to not require expensive numerical simulations on massive supercomputers to investigate them. We demonstrated the strong similarity between our simulations and published results obtained from computationally expensive simulations, and plan to rely on our reduced model to identify the key mechanisms determining the evolution and strength turbulent driven transport in fusion plasmas. Finally, we proposed a new framework for tokamak reactor design studies, enabling us to consider the relative merits of steady-state versus pulsed fusion reactors. We found that pulsed fusion reactors may benefit most from recent advances in magnet technology, and the availability of very high field magnets. As such, they may become more desirable than steady-state tokamak reactors for cost efficient electricity generation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

LDRD final report on confinement of cluster fusion plasmas with magnetic fields.

Two versions of a current driver for single-turn, single-use 1-cm diameter magnetic field coils have been built and tested at the Sandia National Laboratories for use with cluster fusion experiments at the University of Texas in Austin. These coils are used to provide axial magnetic fields to slow radial loss of electrons from laser-produced deuterium plasmas. Typical peak field strength achievable for the two-capacitor system is 50 T, and 200 T for the ten-capacitor system. Current rise time for both systems is about 1.7 {mu}s, with peak current of 500 kA and 2 MA, respectively. Because the coil must be brought to the laser, the driver needs to be portable and drive currents in vacuum. The drivers are complete but laser-plasma experiments are still in progress. Therefore, in this report, we focus on system design, initial tests, and performance characteristics of the two-capacitor and ten-capacitors systems. The questions of whether a 200 T magnetic field can retard the breakup of a cluster-fusion plasma, and whether this field can enhance neutron production have not yet been answered. However, tools have been developed that will enable producing the magnetic fields needed to answer these questions. These are a two-capacitor, 400-kA system that was delivered to the University of Texas in 2010, and a 2-MA ten-capacitor system delivered this year. The first system allowed initial testing, and the second system will be able to produce the 200 T magnetic fields needed for cluster fusion experiments with a petawatt laser. The prototype 400-kA magnetic field driver system was designed and built to test the design concept for the system, and to verify that a portable driver system could be built that delivers current to a magnetic field coil in vacuum. This system was built copying a design from a fixed-facility, high-field machine at LANL, but made to be portable and to use a Z-machine-like vacuum insulator and vacuum transmission line. This system was sent to the University of Texas in Austin where magnetic fields up to 50 T have been produced in vacuum. Peak charge voltage and current for this system have been 100 kV and 490 kA. It was used this last year to verify injection of deuterium and surrogate clusters into these small, single-turn coils without shorting the coil. Initial test confirmed the need to insulate the inner surface of the coil, which requires that the clusters must be injected through small holes in an insulator. Tests with a low power laser confirmed that it is possible to inject clusters into the magnetic field coils through these holes without destroying the clusters. The university team also learned the necessity of maintaining good vacuum to avoid insulator, transmission line, and coil shorting. A 200-T, 2 MA system was also constructed using the experience from the first design to make the pulsed-power system more robust. This machine is a copy of the prototype design, but with ten 100-kV capacitors versus the two used in the prototype. It has additional inductance in the switch/capacitor unit to avoid breakdown seen in the prototype design. It also has slightly more inductance at the cable connection to the vacuum chamber. With this design we have been able to demonstrate 1 MA current into a 1 cm diameter coil with the vacuum chamber at air pressure. Circuit code simulations, including the additional inductance with the new design, agree well with the measured current at a charge voltage of 40 kV with a short circuit load, and at 50 kV with a coil. The code also predicts that with a charge voltage of 97 kV we will be able to get 2 MA into a 1 cm diameter coil, which will be sufficient for 200 T fields. Smaller diameter or multiple-turn coils will be able to achieve even higher fields, or be able to achieve 200-T fields with lower charge voltage. Work is now proceeding at the university under separate funding to verify operation at the 2-MA level, and to address issues of debris mitigation, measurement of the magnetic field, and operation in vacuum. We anticipate operation at full current with single-turn, magnetic field coils this fall, with 200 T experiments on the Texas Petawatt laser in the spring of 2012.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Isolating and quantifying cross-beam energy transfer in direct-drive implosions on OMEGA and the National Ignition Facility

The angularly resolved mass ablation rates and ablation-front trajectories for Si-coated CH targets were measured in direct-drive inertial confinement fusion experiments to quantify cross-beam energy transfer (CBET) while constraining the hydrodynamic coupling. A polar-direct-drive laser configuration, where the equatorial laser beams were dropped and the polar beams were repointed from a symmetric direct-drive configuration, was used to limit CBET at the pole while allowing it to persist at the equator. The combination of low- and high-CBET conditions observed in the same implosion allowed for the effects of CBET on the ablation rate and ablation pressure to be determined. Hydrodynamic simulations performed without CBET agreed with the measured ablation rate and ablation-front trajectory at the pole of the target, confirming that the CBET effects on the pole are small. The simulated mass ablation rates and ablation-front trajectories were in excellent agreement with the measurements at all angles when a CBET model based on Randall's equations [C. J. Randall et al., Phys. Fluids 24, 1474 (1981)] was included into the simulations with a multiplier on the CBET gain factor. These measurements were performed on OMEGA and at the National Ignition Facility to access a wide range of plasma conditions, laser intensities, and laser beam geometries. The presence of the CBET gain multiplier required to match the data in all of the configurations tested suggests that additional physics effects, such as intensity variations caused by diffraction, polarization effects, or shortcomings of extending the 1-D Randall model to 3-D, should be explored to explain the differences in observed and predicted drive.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Linear regime of two-plasmon decay and stimulated Raman scattering instability near the quarter-critical density in plasmas

A model for the interaction between the laser light and the plasma waves near the quarter-critical density in plasmas has been studied. This model includes, but is not limited to, the instabilities of two-plasmon decay (TPD) and stimulated Raman scattering (SRS). The full simulation results show the instability growth in the wavevector domains corresponding to TPD and SRS, respectively, and the domain between those two. The instability growth rates and thresholds can be calculated in our model for the parameters of the inertial confinement fusion experiments without the approximations common in analytical theories.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Low-Recycling Lithium Boundary and Implications for Plasma Transport

Pumping of incident hydrogen and impurity ions by lithium enables control of the particle inventory and fueling profile in magnetic-confined plasmas, and may raise the plasma temperature near the wall. As a result, the density gradient is expected to contribute substantially to the free-energy, affecting particle and thermal transport from micro-turbulence which is typically the dominant transport mechanism in high-temperature fusion experiments. Transport in gyrokinetic simulations of density-gradient-dominated profiles is characterized by a small linear critical gradient, large particle flux, and preferential diffusion of cold particles. As a result, the heat flux is below 5/2 or even 3/2 times the particle flux, usually assumed to be the minimum for convection. While surprising, this result is consistent with increasing entropy. Coupled TEM-ITG (ion-temperature- gradient) simulations using ηe = ηi find η = ∇T /∇n∼0.8 maximizes the linear critical pressure gradient, which suggests that experiments operating near marginal ITG stability with larger η would increase the linear critical pressure gradient by transferring free-energy from the temperature gradient to the density gradient. Simulations were performed with profiles predicted for the Lithium Tokamak Experiment (LTX) if ion thermal transport was neoclassical, while electron thermal transport and particle transport were a fixed ratio above the neoclassical level. A robust TEM instability was found for the outer half radius, while the ITG was found to be driven unstable as well during gas puff fueling. This suggests that TEM transport will be an important transport mechanism in high-temperature low-recycling fusion experiments, and in the absence of stabilizing mechanisms, may dominate over neoclassical transport. A diagnostic suite has been developed to measure hydrogen and impurity emission in LTX in order to determine the lower bound on recycling that can be achieved in a small tokamak using solid lithium coatings, assess its dependence on the operating condition of the lithium surface, and evaluate its impact on the discharge. Coatings on the close-fitting stainless-steel substrate produce a significant reduction in recyling, so that the effective particle confinement times are as low as 1 ms. Measurements of particle inventory in the plasma and hydrogen Lyman-α emission indicate that hydrogen recycling at the surface increases as subsequent discharges are performed; nevertheless, strong pumping of hydrogen is observed even after almost double the cumulative fueling is applied that should saturate the lithium coating to the penetration depth of hydrogen ions. Probe measurements show that when external fueling is terminated, the scrape-off-layer of discharges with fresh coatings decays to lower density and rises to higher electron temperature than for discharges with a partially-passivated surface, consistent with reduced edge cooling from recycled particles. Near the end of the discharge, higher plasma current correlates with reduced τp * and hydrogen emission, suggesting that discharges with fresh coatings achieve higher electron temperature in the core. A novel approach using neutral modeling was developed for the inverse problem of determining the distribution of recycled particle flux from PFC surfaces given a large number of emission measurements, revealing that extremely low levels of recycling (Rcore∼0.6 and Rplate∼0.8) have been achieved with solid lithium coatings. Together with impurity emission measurements, modeling suggests that during periods of particularly low electron density, influx of impurities from the walls contributes substantially to the global particle balance.

magnetic confinement↗

In Situ Real-Time Radiographic Study of Thin Film Formation Inside Rotating Hollow Spheres

Hollow spheres with uniform coatings on the inner surface have applications in optical devices, time- or site controlled drug release, heat storage devices, and target fabrication for inertial confinement fusion experiments. The fabrication of uniform coatings, which is often critical for the application performance, requires precise understanding and control over the coating process and its parameters. Here, we report on in-situ real-time radiography experiments that provide critical spatio-temporal information about the distribution of fluids inside hollow spheres during uniaxial rotation. Image analysis and computer fluid dynamics simulations were used to explore the effect of liquid viscosity and rotational velocity on the film uniformity. The data were then used to demonstrate the fabrication of uniform sol-gel chemistry derived porous polymer films inside 2mm inner diameter diamond shells.

aerogel↗

Liquid Metal Walls, Lithium, And Low Recycling Boundary Conditions In Tokamaks

At present, the only solid material believed to be a viable option for plasma-facing components (PFCs) in a fusion reactor is tungsten. Operated at the lower temperatures typical of present-day fusion experiments, tungsten is known to suffer from surface degradation during long-term exposure to helium-containing plasmas, leading to reduced thermal conduction to the bulk, and enhanced erosion. Existing alloys are also quite brittle at temperatures under 700 deg. C. However, at a sufficiently high operating temperature (700 - 1000 deg. C), tungsten is self-annealing and it is expected that surface damage will be reduced to the point where tungsten PFCs will have an acceptable lifetime in a reactor environment.The existence of only one potentially viable option for solid PFCs, though, constitutes one of the most significant restrictions on design space for DEMO and follow-on fusion reactors. In contrast, there are several candidates for liquid metal-based PFCs, including gallium, tin, lithium, and tin-lithium eutectics. We will discuss options for liquid metal walls in tokamaks, looking at both high and low recycling materials. We will then focus in particular on one of the candidate liquids, lithium.Lithium is known to have a high chemical affinity for hydrogen, and has been shown in test stands and fusion experiments to produce a low recycling surface, especially when liquid. Because it is also low-Z and is usable in a tokamak over a reasonable temperature range (200 - 400 deg. C), it has been now been used as a PFC in several confinement experiments (TFTR, T11-M, CDX-U, NSTX, FTU, and TJ-II), with favorable results. The consequences of substituting low recycling walls for the traditional high recycling variety on tokamak equilibria are very extensive. We will discuss some of the expected modifications, briefly reviewing experimental results, and comparing the results to expectations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Verification of particle simulation of radio frequency waves in fusion plasmas

Radio frequency (RF) waves can offer heating, current and flow drive, as well as instability control for steady state operations of fusion experiments. A particle simulation model has been designed in this work to provide a first-principles tool for studying the RF nonlinear interactions with plasmas. In this model, ions are considered as fully kinetic particles using the Vlasov equation and electrons are treated as guiding centers using the drift kinetic equation. This model has been implemented in a global gyrokinetic toroidal code using real electron-to-ion mass ratio. To confirm the model, linear simulations of ion plasma oscillation, ion Bernstein wave, and lower hybrid wave are carried out in cylindrical geometry and found to agree well with analytic predictions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mechanisms of impulsive magnetic reconnection: Global and local aspects

The global and local aspects of mechanisms of impulsive magnetic reconnection are discussed focusing on results from a dedicated laboratory experiment, MRX (Magnetic Reconnection Experiment), as well as fusion experiments. Possible application of the present analysis to reconnection phenomena in solar and space plasmas is also discussed. An external force which drives internal current in a fusion plasma causes magnetic flux to accumulate in a core section of the plasma (flux build-up). When the flux build-up generates a magnetic profile that satisfies a condition for a global magnetohydrodynamic instability to develop, reconnection takes place in an induced current layer generated by the instability leading to a global self-organization of the plasma. Generally the flux build-up phase is significantly longer than the reconnection time, {tau}{sub H} >> {tau}{sub Rec}, thus making the waveform of flux evolution or other plasma parameters sawtooth shaped. In the reconnection layer of collisionless plasmas, the two fluid dynamics would lead to the formation of a narrow electron current channel which tends to become unstable against micro-instabilities, leading to an unsteady or impulsive reconnection. A common feature of impulsive reconnection after flux build-up is presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Design and fabrication of a window for the gas Cherenkov detector 3

The gas Cherenkov detector 3 was designed at Los Alamos National Laboratory for use in inertial confinement fusion experiments at both the Omega Laser Facility and the National Ignition Facility. This instrument uses a low-Z gamma-to-electron convertor plate and high pressure gas to convert MeV gammas into UV/visible Cherenkov photons for fast optical detection. This is a follow-on diagnostic from previous versions, with two notable differences: the pressure of the gas is four times higher, and it allows the use of fluorinated gas, requiring metal seals. These changes force significant changes in the window component, having a unique set of requirements and footprint limitations. The selected solution for this component, a sapphire window brazed into a stainless steel flange housing, is described.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Adiabat-shaping in indirect drive inertial confinement fusion

Adiabat-shaping techniques were investigated in indirect drive inertial confinement fusion experiments on the National Ignition Facility as a means to improve implosion stability, while still maintaining a low adiabat in the fuel. Adiabat-shaping was accomplished in these indirect drive experiments by altering the ratio of the picket and trough energies in the laser pulse shape, thus driving a decaying first shock in the ablator. This decaying first shock is designed to place the ablation front on a high adiabat while keeping the fuel on a low adiabat. These experiments were conducted using the keyhole experimental platform for both three and four shock laser pulses. This platform enabled direct measurement of the shock velocities driven in the glow-discharge polymer capsule and in the liquid deuterium, the surrogate fuel for a DT ignition target. The measured shock velocities and radiation drive histories are compared to previous three and four shock laser pulses. This comparison indicates that in the case of adiabat shaping the ablation front initially drives a high shock velocity, and therefore, a high shock pressure and adiabat. The shock then decays as it travels through the ablator to pressures similar to the original low-adiabat pulses when it reaches the fuel. This approach takes advantage of initial high ablation velocity, which favors stability, and high-compression, which favors high stagnation pressures.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Trapping induced nonlinear behavior of backward stimulated Raman scattering in multi-speckled laser beams

In inertial confinement fusion experiments, stimulated Raman scattering (SRS) occurs when electron density fluctuations are amplified resonantly by the incident laser beams and scattered light. These beams comprise several thousands of individual laser speckles. We have found in single-speckle studies that electron trapping lowers the threshold intensity for SRS onset to a value below that from linear theory and enhances scattering. The trapping-induced plasma-wave frequency shift leads to wave-front bowing and filamentation processes that saturate SRS and limit scattering within a speckle. With large-scale simulations, we have now examined how laser speckles interact with one another through three-dimensional (3D) particle-in-cell (PIC) simulations of two interacting speckles and 2D PIC simulations of ensembles of laser speckles (hundreds of speckles). Our work shows that kinetic trapping physics also governs the onset and saturation of SRS in ensembles of speckles. Speckles interact in a manner that is nonlinear and nonlocal: An intense speckle can destabilize its neighbors through transport of hot electrons and SRS waves, resulting in enhanced emission of particles and waves that, in turn, act upon the original speckle. In this manner, speckles below threshold when in isolation can be above the threshold in multi-speckled beams under conditions for laser-driven fusion experiments at the National Ignition Facility (NIF) and ensembles of speckles are thus found to collectively lower the SRS onset threshold. Simulations of the hohlraum interior where laser beams overlap show that multi-speckled laser beams at low average intensity (a few times 10{sup 14} W/cm{sup 2}) have correspondingly lower thresholds for enhanced SRS and that the sub-ps bursts of SRS saturate through trapping induced nonlinearities. Because of electron trapping effects, SRS reflectivity grows slowly with average laser intensity. While SRS reflectivity saturates under NIF conditions, SRS hot electron energy increases with increasing laser intensity and may contribute to capsule preheat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Real-time MSE measurements for current profile control on KSTAR

To step up from current day fusion experiments to power producing fusion reactors, it is necessary to control long pulse, burning plasmas. Stability and confinement properties of tokamak fusion reactors are determined by the current or q profile. In order to control the q profile, it is necessary to measure it in real-time. A real-time motional Stark effect diagnostic is being developed at Korean Superconducting Tokamak for Advanced Research for this purpose. This paper focuses on 3 topics important for real-time measurements: minimize the use of ad hoc parameters, minimize external influences and a robust and fast analysis algorithm. Specifically, we have looked into extracting the retardance of the photo-elastic modulators from the signal itself, minimizing the influence of overlapping beam spectra by optimizing the optical filter design and a multi-channel, multiharmonic phase locking algorithm.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Constraints on ion velocity distributions from fusion product spectroscopy

Abstract Recent inertial confinement fusion experiments have shown primary fusion spectral moments which are incompatible with a Maxwellian velocity distribution description. These results show that an ion kinetic description of the reacting ions is necessary. We develop a theoretical classification of non-Maxwellian ion velocity distributions using the spectral moments. At the mesoscopic level, a monoenergetic decomposition of the velocity distribution reveals there are constraints on the space of spectral moments accessible by isotropic distributions. General expressions for the directionally dependent spectral moments of anisotropic distributions are derived. At the macroscopic level, a distribution of fluid element velocities modifies the spectral moments in a constrained manner. Experimental observations can be compared to these constraints to identify the character and isotropy of the underlying reactant ion velocity distribution and determine if the plasma is hydrodynamic or kinetic.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗