SEARCH · Search NASA

Results for “generative diffusion model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Use of experimental separation limits in the theoretical design of V/STOL inlets

Experimental data from several model inlets are used to generate two parameters which are related to the limit of operation for inlet flow separation. One parameter, called the diffusion ratio, is the ratio of the peak velocity on the inlet surface to the velocity at the diffuser exit and is related to the boundary-layer separation at low throat Mach numbers. The other parameter, the peak Mach number on the inlet surface, is related to the separation at high throat Mach numbers. These parameters are easily calculated from potential flow solutions and thus can be used as a design tool in screening proposed inlet geometries. An illustrative example of an application to an inlet design study for a tilt nacelle VTOL airplane is presented. The value of contraction ratio required to meet the operating requirements yet allow the inlet to remain free of separation as indicated by the two separation parameters is shown.

Boles, M. A.↗

NASA NTRS1975

A three-dimensional dynamical-chemical model of atmospheric ozone

A three-year integration of a global three-dimensional model including dynamics and simple photochemistry is used to predict ozone. Good agreement with observation is obtained for stratospheric motion patterns, meridional circulations, ozone density as a function of height and latitude, eddy transports of ozone, surface destruction of ozone, and correlations of ozone with other variables. The annual cycle of columnar ozone in high latitudes is present, but at a smaller amplitude than observed. Vertical transport of ozone downward from the main generation level at 30 km is accomplished primarily by small-scale eddy diffusion between 20 and 30 km and again near the ground; large-scale vertical transport dominates in between. The model predicts a secondary maximum in ozone mixing ratio at 45 km somewhat equatorward of the winter polar-night zone. This feature, recently observed from satellite measurements, is thought to be caused by the temperature dependence of reaction rates in the Chapman scheme. The principal deficiency of the model is an underprediction of the spring ozone concentration in high latitudes in the lower stratosphere.

Cunnold, D.↗

NASA NTRS1999

Dynamical Signatures of Living Systems

One of the main challenges in modeling living systems is to distinguish a random walk of physical origin (for instance, Brownian motions) from those of biological origin and that will constitute the starting point of the proposed approach. As conjectured, the biological random walk must be nonlinear. Indeed, any stochastic Markov process can be described by linear Fokker-Planck equation (or its discretized version), only that type of process has been observed in the inanimate world. However, all such processes always converge to a stable (ergodic or periodic) state, i.e., to the states of a lower complexity and high entropy. At the same time, the evolution of living systems directed toward a higher level of complexity if complexity is associated with a number of structural variations. The simplest way to mimic such a tendency is to incorporate a nonlinearity into the random walk; then the probability evolution will attain the features of diffusion equation: the formation and dissipation of shock waves initiated by small shallow wave disturbances. As a result, the evolution never "dies:" it produces new different configurations which are accompanied by an increase or decrease of entropy (the decrease takes place during formation of shock waves, the increase-during their dissipation). In other words, the evolution can be directed "against the second law of thermodynamics" by forming patterns outside of equilibrium in the probability space. Due to that, a specie is not locked up in a certain pattern of behavior: it still can perform a variety of motions, and only the statistics of these motions is constrained by this pattern. It should be emphasized that such a "twist" is based upon the concept of reflection, i.e., the existence of the self-image (adopted from psychology). The model consists of a generator of stochastic processes which represents the motor dynamics in the form of nonlinear random walks, and a simulator of the nonlinear version of the diffusion equation which represents the mental dynamics. It has been demonstrated that coupled mental-motor dynamics can simulate emerging self-organization, prey-predator games, collaboration and competition, "collective brain," etc.

Zak, M.↗

NASA NTRSDate not supplied

NASA HECC Geometry and Performance Review Part 1: Validation of a Computational Model for the Vaneless Diffuser Configuration with As-Manufactured Impeller Geometry

An investigation of the NASA High Efficiency Centrifugal Compressor (HECC) vaneless diffuser configuration was performed. This multipart investigation focused on validating the computational model against experimental data. The validated model was then used to explore the effects of observed geometric differences between the as-manufactured and design-intent impellers. Lastly, the validated model was used for comparison against an experimental tip clearance study. Details regarding each of the parts are detailed below: A multipart investigation of the NASA High Efficiency Centrifugal Compressor (HECC) vaneless diffuser configuration was performed. Part I of the investigation focused on describing the HECC vaneless computational model and its validation against the experimental data published in GT2023-103128. To generate the model, a verification of the manufactured impeller was performed and was confirmed to match the impeller CAD. Section data from the impeller CAD, referred to as As-Manufactured, were used in the model. Steady RANS simulations using a multiblock structured mesh were used to conduct a mesh convergence study. The resultant mesh was then used for simulations at both design-speed and off-design speed conditions. The simulations compared well to data in both 1D and 2D terms. Based on the observed results the model was deemed validated and was used in the latter two parts of the multipart investigation.

centrifugal compressor↗

NASA NTRS2014

Badhwar-O'Neill 2011 Galactic Cosmic Ray Model Update and Future Improvements

The Badhwar-O'Neill Galactic Cosmic Ray (GCR) Model based on actual GCR measurements is used by deep space mission planners for the certification of microelectronic systems and the analysis of radiation health risks to astronauts in space missions. The BO GCR Model provides GCR flux in deep space (outside the earth's magnetosphere) for any given time from 1645 to present. The energy spectrum from 50 MeV/n - 20 GeV/n is provided for ions from hydrogen to uranium. This work describes the most recent version of the BO GCR model (BO'11). BO'11 determined the GCR flux at a given time applying an emperical time delay function to past sunspot activity. We describe the GCR measurement data used in the BO'11 update - modern data from BESS, PAMELA, CAPRICE, and ACE emphasized more than the older balloon data used for the previous BO model (BO'10). We look at the GCR flux for the last 24 solar minima and show how much greater the flux was for the cycle 24 minimum in 2010. The BO'11 Model uses the traditional, steady-state Fokker-Planck differential equation to account for particle transport in the heliosphere due to diffusion, convection, and adiabatic deceleration. It assumes a radially symmetrical diffusion coefficient derived from magnetic disturbances caused by sunspots carried outward by a constant solar wind. A more complex differential equation is now being tested to account for particle transport in the heliosphere in the next generation BO model. This new model is time-dependent (no longer a steady state model). In the new model, the dynamics and anti-symmetrical features of the actual heliosphere are accounted for so emperical time delay functions will no longer be required. The new model will be capable of simulating the more subtle features of modulation - such as the Sun's polarity and modulation dependence on gradient and curvature drift. This improvement is expected to significantly improve the fidelity of the BO GCR model. Preliminary results of its performance will be presented.

O'Neill, Pat M.↗

NASA NTRS2014

Badhwar-O'Neill 2011 Galactic Cosmic Ray Model Update and Future Improvements

The Badhwar-O'Neill Galactic Cosmic Ray (GCR) Model based on actual GR measurements is used by deep space mission planners for the certification of micro-electronic systems and the analysis of radiation health risks to astronauts in space missions. The BO GCR Model provides GCR flux in deep space (outside the earth's magnetosphere) for any given time from 1645 to present. The energy spectrum from 50 MeV/n-20 GeV/n is provided for ions from hydrogen to uranium. This work describes the most recent version of the BO GCR model (BO'11). BO'11 determines the GCR flux at a given time applying an empirical time delay function to past sunspot activity. We describe the GCR measurement data used in the BO'11 update - modern data from BESS, PAMELA, CAPRICE, and ACE emphasized for than the older balloon data used for the previous BO model (BO'10). We look at the GCR flux for the last 24 solar minima and show how much greater the flux was for the cycle 24 minimum in 2010. The BO'11 Model uses the traditional, steady-state Fokker-Planck differential equation to account for particle transport in the heliosphere due to diffusion, convection, and adiabatic deceleration. It assumes a radially symmetrical diffusion coefficient derived from magnetic disturbances caused by sunspots carried onward by a constant solar wind. A more complex differential equation is now being tested to account for particle transport in the heliosphere in the next generation BO model. This new model is time-dependent (no longer a steady state model). In the new model, the dynamics and anti-symmetrical features of the actual heliosphere are accounted for so empirical time delay functions will no longer be required. The new model will be capable of simulating the more subtle features of modulation - such as the Sun's polarity and modulation dependence on the gradient and curvature drift. This improvement is expected to significantly improve the fidelity of the BO GCR model. Preliminary results of its performance will be presented.

O'Neill, Pat M.↗

NASA NTRS2008

Precipitation Model Validation in 3rd Generation Aeroturbine Disc Alloys

In support of application of the DARPA-AIM methodology to the accelerated hybrid thermal process optimization of 3rd generation aeroturbine disc alloys with quantified uncertainty, equilibrium and diffusion couple experiments have identified available fundamental thermodynamic and mobility databases of sufficient accuracy. Using coherent interfacial energies quantified by Single-Sensor DTA nucleation undercooling measurements, PrecipiCalc(TM) simulations of nonisothermal precipitation in both supersolvus and subsolvus treated samples show good agreement with measured gamma particle sizes and compositions. Observed longterm isothermal coarsening behavior defines requirements for further refinement of elastic misfit energy and treatment of the parallel evolution of incoherent precipitation at grain boundaries.

Olson, G. B.↗

NASA NTRS1977

Use of experimental separation limits in the theoretical design of V/STOL inlets

Experimental data from several model inlets have been used to generate two parameters which are related to the limit of operation for inlet flow separation. One parameter, called the diffusion ratio, is the ratio of the peak velocity on the inlet surface to the velocity at the diffuser exit and is related to the boundary-layer separation at low throat Mach numbers. The other parameter, the peak Mach number on the inlet surface, is related to the separation at high throat Mach numbers. These parameters are easily calculated from potential flow solutions and thus can be used as a design tool in screening proposed inlet geometries. Any of the geometric design variables can be analyzed by this technique; but, this paper is restricted to the consideration of the internal lip contraction ratio. An illustrative example of an application to an inlet design study for a tilt nacelle VTOL airplane is presented. The study will show what value of contraction ratio is required to meet the operating requirements yet allow the inlet to remain free of separation as indicated by the two separation parameters.

Boles, M. A.↗

NASA NTRS1977

Ion-beam-induced atomic mixing

Calculations based on the diffusion model are presented of atomic mixing by ion bombardment. This mixing is assumed to have its basis, as does sputtering, in the collision cascades generated by the primary beam. Sharp interfaces within a target are seen to be smoothed by ion bombardment. Mixing may place fundamental limits on the resolution of ion microprobes.

Haff, P. K.↗

NASA NTRS1980

Low speed test of the aft inlet designed for a tandem fan V/STOL nacelle

An approximately .25 scale model of a Tandem Fan nacelle designed for a Type A V/STOL aircraft configuration was tested in a 10-by-10 foot wind tunnel. A 12 inch, tip driven, turbofan simulator was used to provide the suction source for the aft fan inlet. The front fan inlet was faired over for this test entry. Model variables consisted of a long aft inlet cowl, a short aft inlet cowl, a shaft simulator, blow-in door passages and diffuser vortex generators. Inlet pressure recovery, distortion, inlet angle of attack separation limits were evaluated at tunnel velocities from 0 to 240 knots, angles of attack from -10 to 40 degrees and inlet flow rates representative of throat Mach numbers of 0.1 to 0.6. High inlet performance and stable operation was verified at all design forward speed and angle of attack conditions. The short aft inlet configuration provided exceptionally high pressure recovery except at the highest combination of angle of attack and forward speed. The flow quality at the fan face was somewhat degraded by the addition of blow-in door passages to the long aft inlet configuration due to the pressure disturbances generated by the flow entering the diffuser through the auxiliary air passages.

Rhoades, W. W.↗

NASA NTRS1981

Additional testing of the inlets designed for a tandem fan V/STOL nacelle

The wind tunnel testing of a scale model of a tandem fan nacelle designed for a type (subsonic cruise) V/STOL aircraft configuration is discussed. The performance for the isolated front inlet and for the combined front and aft inlets is reported. Model variables include front and aft inlets with aft inlet variations of short and long aft inlet cowls, with a shaft simulator and diffuser vortex generators, cowl lip fillets, and nacelle strakes. Inlet pressure recovery, distortion, and inlet angle-to-attack separation limits were evaluated at tunnel velocity from 0 to 240 knots, angles-of-attack from -10 to +40 degrees and inlet flow rates corresponding to throat Mach number from 0.0 to 0.6. Combined nacelle pitch and yaw runs up to 30 deg. were also made.

Ybarra, A. H.↗

NASA NTRS1991

Fractal dynamics of bioconvective patterns

Biologically generated cellular patterns, sometimes called bioconvective patterns, are found to cluster into aggregates which follow fractal growth dynamics akin to diffusion-limited aggregation (DLA) models. The pattern formed is self-similar with fractal dimension of 1.66 +/-0.038. Bioconvective DLA branching results from thermal roughening which shifts the balance between ordering viscous forces and disordering cell motility and random diffusion. The phase diagram for pattern morphology includes DLA, boundary spokes, random clusters, and reverse clusters.

Noever, David A.↗

NASA NTRS1994

Inducer analysis/pump model development

Current design of high performance turbopumps for rocket engines requires effective and robust analytical tools to provide design information in a productive manner. The main goal of this study was to develop a robust and effective computational fluid dynamics (CFD) pump model for general turbopump design and analysis applications. A finite difference Navier-Stokes flow solver, FDNS, which includes an extended k-epsilon turbulence model and appropriate moving zonal interface boundary conditions, was developed to analyze turbulent flows in turbomachinery devices. In the present study, three key components of the turbopump, the inducer, impeller, and diffuser, were investigated by the proposed pump model, and the numerical results were benchmarked by the experimental data provided by Rocketdyne. For the numerical calculation of inducer flows with tip clearance, the turbulence model and grid spacing are very important. Meanwhile, the development of the cross-stream secondary flow, generated by curved blade passage and the flow through tip leakage, has a strong effect on the inducer flow. Hence, the prediction of the inducer performance critically depends on whether the numerical scheme of the pump model can simulate the secondary flow pattern accurately or not. The impeller and diffuser, however, are dominated by pressure-driven flows such that the effects of turbulence model and grid spacing (except near leading and trailing edges of blades) are less sensitive. The present CFD pump model has been proved to be an efficient and robust analytical tool for pump design due to its very compact numerical structure (requiring small memory), fast turnaround computing time, and versatility for different geometries.

Cheng, Gary C.↗

NASA NTRS1994

Stream interfaces and energetic ions closer than expected: Analyses of Pioneers 10 and 11 observations

An empirical study of corotating interaction regions (CIRs) observed between 3.9 AU and 5.9 AU on Pioneers 10 and 11 shows that the main corotation energetic ion population (CEIP), which is associated with the trailing reverse shock, terminates within the CIR at a definite, structural boundary, which we show here is the stream interface. This new result has significant implications for solar wind and energetic particle modeling. In particular it implies either that the reverse shock forms closer to the stream interface than models suggest or that the theories that treat the generation and transport of these energetic ions, such as preshock Fermi acceleration and cross-field diffusion must be combined or extended. We test these scenarios by comparing the CEIP intensity profiles on the two sides of the stream interface. We find that while each automatically accounts for one or two aspects of the results none of them alone can account for all of our empirical results.

Intriligator, Devrie S.↗

NASA NTRS1995

A source-sink model of the generation of plate tectonics from non-Newtonian mantle flow

A model of mantle convection which generates plate tectonics requires strain rate- or stress-dependent rheology in order to produce strong platelike flows with weak margins as well as strike-slip deformation and plate spin (i.e., toroidal motion). Here, we employ a simple model of source-sink driven surface flow to determine the form of such a rheology that is appropriate for Earth's present-day plate motions. In this model, lithospheric motion is treated as shallow layer flow driven by sources and sinks which correspond to spreading centers and subduction zones, respectively. Two plate motion models are used to derive the source sink field. As originally implied in the simpler Cartesian version of this model, the classical power law rheologies do not generate platelike flows as well as the hypothetical Whitehead-Gans stick-slip rheology (which incorporates a simple self-lubrication mechanism). None of the fluid rheologies examined, however, produce more than approximately 60% of the original maximum shear. For either plate model, the viscosity fields produced by the power law rheologies are diffuse, and the viscosity lows over strike-slip shear zones or pseudo-margins are not as small as over the prescribed convergent-divergent margins. In contrast, the stick-slip rheology generates very platelike viscosity fields, with sharp gradients at the plate boundaries, and margins with almost uniformly low viscosity. Power law rheologies with high viscosity contrasts, however, lead to almost equally favorable comparisons, though these also yield the least platelike viscosity fields. This implies that the magnitude of toroidal flow and platelike strength distributions are not necessarily related and thus may present independent constraints on the determination of a self-consistent plate-mantle rheology.

Bercovici, David↗

NASA NTRS1986

Simulation of the thermospheric tides by use of the NCAR thermospheric general circulation model

Numerical calculations of the thermospheric tidal winds and temperatures at equinox are presented. The calculations were made using the National Center for Atmospheric Research Thermospheric General Circulation Model (TGCM), which includes the effects of viscosity, conductivity, diffusion, ion drag, winds, and temperature gradients. The thermospheric diurnal and semidiurnal tides are excited in situ by solar heating and by ion-neutral momentum coupling. The semidiurnal tidal calculations also include the effects of upward propagating waves generated by heating in the lower atmosphere. This semidiurnal propagating component is modeled by use of the classical tidal perturbations as lower boundary conditions. The model is tuned by adjusting the propagating tidal forcing term until calculated semidiurnal wind and temperature fields best approximate incoherent scatter observations. The tidal TGCM results are consistent with previous theoretical work and successfully reproduce high altitude temperature and meridional velocity data, but they give significantly lower magnitudes for velocities and temperatures near 160 km than are seen by observations.

Fensen, C. G.↗

NASA NTRS1977

Gravitational effects on chemically reacting laminar boundary layer flows over a horizontal flat plate

A theoretical study of the chemically reacting laminar boundary layer flow over a horizontal flat plate with gravitationally induced buoyant force is presented. A diffusion flame sheet model was used to describe the combustion process. The effects of gravity on the purely force convection flow can be characterized by a dimensionless coordinate quantity, which is involved in the generation of the governing equations. A numerical solution of the zero and first order governing equations subject to the appropriate physical boundary conditions was obtained. It is shown that the cross stream buoyancy induced body force acts effectively to produce a streamwise pressure gradient in the fluid adjacent to the plate surface. It is concluded that buoyancy plays an important role in boundary layer diffusion flames.

Lavid, M.↗

NASA NTRS1990

Investigation of turbulent transport in an axisymmetric sudden expansion

Simultaneous two-component laser velocimeter measurements were made in the incompressible turbulent flowfield following an axisymmetric sudden expansion. Mean velocities, Reynolds stresses, and triple products were measured and are presented at axial positions ranging from x/H = 0.2-14. A balance of the turbulent kinetic energy in the flow was performed. The production, convection, and diffusion of turbulent kinetic energy were computed directly from the experimental data using central differencing. A specially designed correction lens was employed to correct for optical aberrations introduced by the circular tube. This lens system allowed the accurate simultaneous measurement of axial and radial velocities in the test section. The experimental measurements were compared to predictions generated by a code that employed the k-epsilon turbulence model. Agreement was good for mean axial velocities, turbulent kinetic energy, and turbulent shear stresses. However, the modeled turbulent normal stresses where in poor agreement with the measured values. The modeled diffusion of turbulent kinetic energy was underpredicted in the region between the shear layer and the centerline of the flow giving lower values of turbulent kinetic energy downstream of the potential core than measured.

Gould, Richard D.↗