Search NASA⌕ Search

SEARCH · Search NASA

Results for “graphite modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Multiphysics Simulation of Moisture-Graphite Oxidation in MHTGR

A small amount of moisture on the ppm level could present in the primary helium coolant under normal operations of High-Temperature Gas-cooled Reactors (HTGRs). One potential safety issue related to HTGRs is the chronic moisture-graphite oxidation, which could affect the integrity of the fuel blocks and reflectors in the reactor core, and the support columns in the hot plenum. However, it is infeasible to perform chronic moisture-graphite oxidation tests under the prototypic high-pressure, high-temperature conditions over a long period of time that is comparable to the full service time, i.e., 36 months for Modular High Temperature Gas-cooled Reactor (MHTGR). As an alternate, accelerated moisture-graphite oxidation tests at the atmospheric pressure and high moisture concentrations have been performed in the literature. Through these accelerated tests, global reaction rate equations have been proposed, which makes it possible to study the moisture-graphite oxidation numerically. This paper is aimed to establish a multiphysics model that can evaluate the moisture-graphite oxidation under MHTGR normal operation conditions. COMSOL Multiphysics was applied to couple the fluid flow, heat and mass transfer, chemical reaction and material structural changes. To reduce the calculation time, the prototypic three-dimensional (3-D) structures were simplified into a two-dimensional (2-D) simulation domain. The performance of four nuclear grades of graphite (IG-110, 2114, PCEA, and NBG-17) over a 36-month service period was then investigated under the most likely prototypic conditions of MHTGR. The simulation results indicate that most oxidation occurs in the three or four bottom fuel blocks due to their higher temperatures. In general, however, only a thin layer of 1 mm into the graphite will be considerably oxidized even for those three or four bottom fuel blocks.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Density of intercalated graphite fibers

The density of Amoco P-55, P-75, P-100, and P-120 pitch-based graphite fibers and their intercalation compounds with bromine, iodine monochloride, and copper (II) chloride have been measured using a density gradient column. The distribution of densities within a fiber type is found to be a sensitive indicator of the quality of the intercalation reaction. In all cases the density was found to increase, indicating that the mass added to the graphite is dominant over fiber expansion. Density increases are small (less than 10 percent) giving credence to a model of the intercalated graphite fibers which have regions which are intercalated and regions which are not.

Gaier, James R.↗

Density of intercalated graphite fibers

The density of Amoco P-55, P-75, P-100, and P-120 pitch-based graphite fibers and their intercalation compounds with bromine, iodine monochloride, and copper (II) chloride have been measured using a density gradient column. The distribution of densities within a fiber type is found to be a sensitive indicator of the quality of the intercalation reaction. In all cases the density was found to increase, indicating that the mass added to the graphite is dominant over fiber expansion. Density increases are small (less than 10 percent) giving credence to a model of the intercalated graphite fibers which have regions which are intercalated and regions which are not.

Gaier, James R.↗

Machine learning predictions of diffusion in bulk and confined ionic liquids using simple descriptors

Ionic liquids have many intriguing properties and widespread applications such as separations and energy storage. However, ionic liquids are complex fluids and predicting their behavior is difficult, particularly in confined environments. We introduce fast and computationally efficient machine learning (ML) models that can predict diffusion coefficients and ionic conductivity of bulk and nanoconfined ionic liquids over a wide temperature range (350–500 K). The ML models are trained on molecular dynamics simulation data for 29 unique ionic liquids as bulk fluids and confined in graphite slit pores. This model is based on simple physical descriptors of the cations and anions such as molecular weight and surface area. Here, we also demonstrate that accurate results can be obtained using only descriptors derived from SMILES (simplified molecular-input line-entry system) codes for the ions with minimal computational effort. This offers a fast and efficient method for estimating diffusion and conductivity of nanoconfined ionic liquids at various temperatures without the need for expensive molecular dynamics simulations.

74 ATOMIC AND MOLECULAR PHYSICS↗

Summary of US DOE R&D Activities on Graphite Oxidation (2006–2021)

The objective of the international collaboration between United States Department of Energy (U.S.-DOE) and Generation IV International Forum (GIF) is the development of the next generation of nuclear energy systems. The current GIF Project Arrangement (PA) on Materials (2018-2022) was revised in 2019 and extended for another 10 years (2020-2030). The Work Package 1 (“Graphite”) of the extended Project Plan (PP) on Materials specifies technical tasks and High Level Deliverables for research and development (R&D) activities related to using graphite in fuel elements, reflectors, and support structures of Very High Temperature Reactors (VHTR). The graphite tasks include specification and acquisition, qualification and development of new grades, characterization of properties, and development of behavior models. Specifically, Task 1.4 (“Graphite Oxidation Behavior”) outlines planned activities related to acute oxidation by air and chronic oxidation by impurities in the helium coolant. A final report on experimental data regarding graphite oxidation behavior is scheduled for 2022 (deliverable 3.1.1.4.a). In preparation of this deliverable, this document summarizes the R&D activities funded by U.S.-DOE from 2006 (the inception of the VHTR system arrangement) through present (2021). This report is being submitted to the GIF Graphite Working Group (GWG) to serve as input for the GWG high-level deliverable to the Project Management Board (PMB) of PA on Materials. Besides U.S.-DOE, other organizations participating to Task 1.4 of the current PA on Materials are: European Commission’s Joint Research Center (JRC), Korea Atomic Energy Research Institute (KAERI), and Japan Atomic Energy Agency (JAEA). U.S.-DOE is the main contributor on graphite oxidation R&D, with 85 % commitment of total funding during 2018-2022.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fast Charging of Li-Ion Cells: Part II. Nonlinear Contributions to Cell and Electrode Polarization

In this series, Li/Cu microprobes are used to monitor potentials of individual electrodes in situ during high-rate charging of Li-ion cells. Here we focus on capacity-limited charging of these cells to 6C, and present a general treatment of polarization that allows for data reduction and accurate interpolation/extrapolation over a wide range of charge rates. We show that the anode impedance as measured both using this new treatment and the more established pulsed-current techniques is not significantly changed after high-rate aging of the cell, including the conditions under which Li plating has occurred. Our measurements suggest that the changes in cell and electrode polarization to a large extent occur through nonlinear effects that involve time-delayed processes. An electrochemical model that includes phase dynamics in lithiated graphite is shown to capture some but not all of the observed trends suggesting that important facets of the high-rate behavior need to be included in such models.

25 ENERGY STORAGE↗

SAM Code Development for Source Term Modeling in Fluoride-salt-cooled High-temperature Reactors

The SAM code is under development and supported by DOE-NE’s Nuclear Energy Advanced Modeling and Simulation program as a modern system-level modeling and simulation tool for advanced non-light water reactor safety analyses. These advanced reactor concepts incorporate novel and improved approaches to achieve safety and economic feasibility. Many concepts leverage higher operating temperatures for improved efficiency with a variety of coolants and structural materials to support those needs. Such design choices may also pose unique radiological source term risks. There are continuous efforts to incorporate new physics and phenomena relevant to advanced reactor concepts, including capabilities to enable system-level source term modeling. The Pebble-Bed Fluoride-salt-cooled High-temperature Reactor (PB-FHR) is a promising candidate among advanced nuclear reactor concepts with its improved passive safety characteristics and high thermal efficiency. In addition to past efforts to support the development and utilization of SAM for PB-FHR safety analysis, the species transport modeling capabilities in SAM have been extended to simulate source term phenomena in concepts like the PB-FHR. The PB-FHR concept utilizes pebble-form TRISO fuel and FLiBe salt coolant to provide robust barriers to the release of almost all fission products and radiological source terms. However, tritium poses a unique radiological risk due to its significant production from neutron interactions with 6 Li and 9 Be in the FLiBe as well as its high mobility at elevated temperatures where it can permeate through structural metals. Secondly, the use of graphite at elevated temperatures poses the risk of oxidation damage to any structural components or fuel pebbles that are exposed to accidental air ingress. This report summarizes progress made in modeling these phenomena in SAM, which leverages the system-level multi-physics thermal hydraulic simulation to support an effective engineering-scale source term modeling capability. A tritium transport model is developed to simulate the various transport pathways in FHR and MSR concepts and is presented through verification and validation examples as well as demonstrations simulating experimental test loops and reference plant FHR models. A graphite oxidation model is also introduced to calculate local oxidation rates and is presented with initial validation results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A phase-field approach to model multi-axial and microstructure dependent fracture in nuclear grade graphite

The fracture behavior of nuclear grade graphites is strongly influenced by underlying microstructural features such as the character of filler particles, and the distribution of pores and voids. These microstructural features influence the crack nucleation and propagation behavior, resulting in quasi-brittle fracture with a tortuous crack path and significant scatter in measured bulk strength. This paper uses a phase-field method to model the microstructural and multi-axial fracture in H-451, a historic variant of nuclear graphite that provides the basis for an idealized study on a legacy grade. The representative volume elements are constructed from randomly located pores with random size obtained from experimentally determined log-normal distribution. The representative volume elements are then subjected to simulated multi-axial loading, and a reasonable agreement of the resulting fracture stress with experiments is obtained. Finally, quasi-brittle stress-strain evolution with a tortuous crack path is also observed from the simulations and is consistent with experimental results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Structure and properties of surface and subsurface defects in graphite accounting for van der Waals and spin-polarization effects

The geometries, formation energies, and diffusion barriers of surface and subsurface intrinsic defects in graphite are calculated using spin-polarized density-functional theory and the generalized gradient approximation with a semiempirical van der Waals (vdW) correction for dispersion interactions. The calculated formation energies and diffusion barriers of subsurface interstitial (I) atoms deviate qualitatively and quantitatively from those of surface adatoms. The same trend is found also for subsurface and adatom clusters (I{sub 2},I{sub 3}). In spite of the semiquantitative agreement on the optimized geometries, the formation energies and diffusion barriers of surface and subsurface vacancies (V), divacancies (VV), and intimate (I-V) Frenkel pairs differ significantly from the values for the analogous defects in the bulk of graphite. This suggests limited transferability of the bulk and subsurface defect models to the surface of graphite. These findings are rationalized in terms of the balance between the covalent and vdW interaction terms at the surface, subsurface, and bulk of graphite. Finally, pairing of individual defects (adatoms, I and V) is calculated to be energetically advantageous both on the surface and in the subsurface regions. This process is shown to either saturate residual dangling bonds or produce singlet spin states, thus contributing to the quenching of residual spin polarization from damaged graphite surfaces.

36 MATERIALS SCIENCE↗

A molecular dynamics study of diamond and graphite under tritium bombardment

Carbon has proven to be a promising plasma facing material in tokamak reactors because of its high thermal conductivity and limited radiative cooling as a plasma contaminant. It is used in a range of forms, mostly graphitic or amorphous. Diamond, however, has superior thermal properties to other forms of carbon but has been largely overlooked due to fears of graphitisation. Tritium retention is, perhaps, the major disadvantage of using carbon as a plasma facing material in a deuterium-tritium fusion reactor. Here, we use molecular dynamics to study the relative performance of diamond and graphite on exposure to tritium bombardment. We model the cumulative bombarded of diamond and graphitic surfaces with a high flux (10{sup 29} m{sup -2} s{sup -1}) of low energy 15 eV tritium atoms. This was done for substrate temperatures in the range 300-2100 K. Below temperatures of graphitisation ({approx}1000 K) the diamond structure confined tritium to the upper surface, this inhibited further structural damage and resulted in lower total retention. The graphitic surface allowed for deeper tritium penetration and therefore greater retention. These results corroborate with recent experimental evidence.

36 MATERIALS SCIENCE↗

Coefficient of restitution for low velocity transverse impact of thin graphite-epoxy laminates

A simple model is presented for the low velocity impact behavior of thin plates composed of T300/5208 graphite/epoxy. The model, which is constructed on the assumption that the plate is inextensible in the fiber direction and that the material is incompressible in the z direction, is able to predict the energy absorbed by the target during an impact event, or the 'coefficient of restitution'. The plate essentially deforms by shear, allowing the model to neglect bending deformations. The coefficient of restitution is predicted to increase with large interlaminar shear strength and low transverse shear modulus of the laminate. The coefficient's experimentally measured values agree with model-predicted values within a reasonable error.

Lal, K. M.↗

Dynamic In‐Plane Heterogeneous and Inverted Response of Graphite to Fast Charging and Discharging Conditions in Lithium‐Ion Pouch Cells

Solutions for improving fast charging of lithium‐ion batteries have largely focused on alleviating through‐plane lithiation gradients while little is understood about in‐plane heterogeneities and how to resolve them. Herein, high‐speed synchrotron X‐ray diffraction (XRD) resolves graphite lithiation spatially and temporally during 6 C charging and 2 C discharging. At every point during operation, considerable differences in the state of lithiation across the pouch cell are present. Some regions are more responsive to operation than others, reaching full lithiation early during charge and full delithiation during discharge. Other regions within the cell never fully delithiate during discharge, despite a prolonged voltage hold at 2.8 V. Using time‐resolved XRD data, the calculated local current density (mA cm −2 ) at the graphite surface shows an unexpected occurrence of local inverted current densities where regions of graphite are observed to delithiate during charging and lithiate during discharging. A pseudo‐3D model is developed for the graphite electrode with spatially varying microstructural tortuosity to show how microstructural heterogeneity could influence spatial charge dynamics. The model could not predict the complex in‐plane charge behavior observed within the cell. Consequently physics‐based charging protocols based on homogeneous electrode assumptions may underestimate the local variations in charge dynamics and occurrence of lithium plating.

25 ENERGY STORAGE↗

THE USA’S ADVANCED REACTOR TECHNOLOGIES (ART) GRAPHITE R&D PROGRAM

The USA DOE Advanced Reactor Technologies (ART) graphite R&D program supporting HTR design is one of the longest running nuclear graphite R&D programs. Significant progress has been made in several areas of research within this extensive program including unirraidated and irradiated testing of nuclear graphite, oxidation results and modeling, fracture behavior, irradiation damage studies, and several international collaboration studies. The latest results in these research areas as well as a discussion of a new direction in nuclear graphite irradiation for the USA program will be presented. Recently, the USA made a decision to support moderate to high dose irradiation of nuclear graphite (0.5 to 15 dpa). This will provide irradiation data for graphite HTR core components up to 15 dpa for numerous nuclear graphite grades. The irradiation plan and a tentative schedule for this new irradiation direction will be presented in detail.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Magnetic properties and concurrence for fluid {sup 3}He on kagome lattice

We present the results of magnetic properties and entanglement for kagome lattice using Heisenberg model with two- and three-site exchange interactions in strong magnetic field. Kagome lattice correspond to the third layer of fluid {sup 3}He absorbed on the surface of graphite. The magnetic properties and concurrence as a measure of pairwise thermal entanglement are studied by means of variational mean-field like treatment based on Gibbs-Bogoliubov inequality. The system exhibits different magnetic behaviors depending on the values of the exchange parameters (J{sub 2}, J{sub 3}). We have obtained the magnetization plateaus at low temperatures. The central theme of the paper is comparing the entanglement and magnetic behavior for kagome lattice. We have found that in the antiferromagnetic region behavior of the concurrence coincides with the magnetic susceptibility one.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Kinetics of Chronic Oxidation of NBG-17 Nuclear Graphite by Water Vapor

This report presents the results of kinetic measurements during accelerated oxidation tests of NBG-17 nuclear graphite by low concentration of water vapor and hydrogen in ultra-high purity helium. The objective is to determine the parameters in the Langmuir-Hinshelwood (L-H) equation describing the oxidation kinetics of nuclear graphite in the helium coolant of high temperature gas-cooled reactors (HTGR). Although the helium coolant chemistry is strictly controlled during normal operating conditions, trace amounts of moisture (predictably < 0.2 ppm) cannot be avoided. Prolonged exposure of graphite components to water vapor at high temperature will cause very slow (chronic) oxidation over the lifetime of graphite components. This behavior must be understood and predicted for the design and safe operation of gas-cooled nuclear reactors. The results reported here show that, in general, oxidation by water of graphite NBG-17 obeys the L-H mechanism, previously documented for other graphite grades. However, the characteristic kinetic parameters that best describe oxidation rates measured for graphite NBG-17 are different than those reported previously for grades H-451 (General Atomics, 1978) and PCEA (ORNL, 2013). In some specific conditions, certain deviations from the generally accepted L-H model were observed for graphite NBG-17. This graphite is manufactured in Germany by SGL Carbon Group and is a possible candidate for the fuel elements and reflector blocks of HTGR.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Effective and accurate approach for modeling of commensurate–incommensurate transition in krypton monolayer on graphite

Commensurate–incommensurate (C-IC) transition of krypton molecular layer on graphite received much attention in recent decades in theoretical and experimental researches. However, there still exists a possibility of generalization of the phenomenon from thermodynamic viewpoint on the basis of accurate molecular simulation. Recently, a new technique was developed for analysis of two-dimensional (2D) phase transitions in systems involving a crystalline phase, which is based on accounting for the effect of temperature and the chemical potential on the lattice constant of the 2D layer using the Gibbs–Duhem equation [E. A. Ustinov, J. Chem. Phys. 140, 074706 (2014)]. The technique has allowed for determination of phase diagrams of 2D argon layers on the uniform surface and in slit pores. This paper extends the developed methodology on systems accounting for the periodic modulation of the substrate potential. The main advantage of the developed approach is that it provides highly accurate evaluation of the chemical potential of crystalline layers, which allows reliable determination of temperature and other parameters of various 2D phase transitions. Applicability of the methodology is demonstrated on the krypton–graphite system. Analysis of phase diagram of the krypton molecular layer, thermodynamic functions of coexisting phases, and a method of prediction of adsorption isotherms is considered accounting for a compression of the graphite due to the krypton–carbon interaction. The temperature and heat of C-IC transition has been reliably determined for the gas–solid and solid–solid system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Identification and Study of Validation Level Test Cases for Computational Modeling of Non-Charring Ablators

Computational modeling of Thermal Protection System (TPS) materials, used for aerospace applications, provides numerous advantages in preliminary selection and design of a heatshield material and shape for atmospheric entry vehicles. However, to serve as a reliable tool for prediction of material thermal and ablative behavior, the modeling approach needs to be validated against real experimental and flight data, preferably at a range of applied conditions. The validation study is typically very complex as it requires reliable measured data not only for the material thermal response and surface recession, but also well characterized environmental conditions. The validation problem becomes even more complex when the material thermal response is dictated by multi-physics effects such as solid conduction, in-depth thermal decomposition, pyrolysis gas flow and chemical reactions. The multi-physics effects complicate not only the modeling effort, but also the experimental measurement for validation of various aspects of the highly coupled problem. In this study, an attempt is made to identify suitable experimental data that could serve as a source for validation of material thermal response modeling tools. To reduce the computational complexity, this study focuses only on non-charring ablators, where the material thermal response could be modeled with a single governing equation for solid conduction and the ablation is limited only to the surface of the material. With a well characterized and publicly available experimental data being sparse, the study is limited in presenting test cases for only three materials: camphor, graphite and FiberForm® in the sequence of increased modeling complexity. Graphite is a commonly used TPS material for aerospace applications, both for leading edges of high-speed vehicles and internal insulation of solid rocket motors. FiberForm® is a porous carbon pre-form used in preparation of the well known PICA material Tran et al. [1996]. Inclusion of camphor into the list is conditioned with the relative simplicity in modeling the material thermal and chemical response and the low-enthalpy flow environment. In addition, camphor has been used as a simple test material for study of flow transition behavior by Stock and Ginoux [1973] and assessment of a heatshield shape change at flight relevant conditions by Rotondi et al. [2022]. In this work, the identified experimental data was extracted from the public literature and test cases that yet have been published. As it was found from the review, not a single test case contains an exhaustive set of data that would validate every aspect of the material physics. However, in the data collected, various aspects of the material behavior can be still validated, such as surface and in-depth temperature, amount of recession and a shape change. The identified experimental data for each case is accompanied with a characterized flow environment and simulated boundary conditions predicted by a Data-Parallel Line Relaxation (DPLR) code Wright et al. [1998]. In addition, material thermal response numerical simulations in each test case are performed with Kentucky Aerothermodynamics and Thermal Response System (KATS-MR) Zibitsker et al. [2022] providing a comparative study and a sanity check for the proposed validation data. Sample results from the performed numerical study are shown below. Figure 1 shows distribution of surface heat flux and pressure values on a hemi-cylinder model made of FiberForm® and tested in HyMETS arc-jet facility. The results are shown for the high pressure condition among the two tests. Flow simulation was performed with DPLR code on a quarter of original geometry. In the figure, the quarter shape was mirrored across zx and xy planes to show the complete distribution. Figure 2 shows the material response results for the high pressure case (7500 Pa), simulated with KATS-MR and a comparison to the experimental data for the surface temperature and shape shape. The simulation was performed on a 2-D slice, extracted in the xy plane at the middle of the sample. Figure 3 shows the material response simulation for the low pressure case (3500 Pa) and a comparison to the experimental data for surface temperature and shape change.

ablation↗