Search NASA⌕ Search

SEARCH · Search NASA

Results for “height estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Wind Conditions for Solar Energy Facility Design Based on Field Measurements at Nevada Solar One

This study characterises near-surface wind conditions at the Nevada Solar One (NSO) concentrated solar power plant using two years of measurements from a 15-m mast located 30 m west of the solar arrays. The surrounding terrain is fairly flat within 3 km, but nearby solar photovoltaic (PV) and concentrated solar power (CSP) installations introduce strong directional wind inhomogeneity, which motivates a sector-based analysis that distinguishes undisturbed inflow from waked flow. The analysis uses data from three sonic anemometers to assess whether turbulence in the surface layer can be represented as Gaussian and whether standard surface-layer scaling remains valid below 10 m height. The roughness length and displacement height are estimated for twelve directional sectors under near-neutral wind conditions, and all three velocity components show departures from Gaussian behaviour. Spectral analysis indicates that the turbulence contains low-frequency fluctuations with amplitudes higher than those predicted by standard models such as the Kaimal model or the Simiu and Scanlan model. The study introduces a new turbulence spectral model based on the eddy-surface-layer framework to better represent near-surface wind turbulence. The analysis further quantifies the influence of the surrounding power plants on mean wind profiles, one-point spectra, and vertical coherence for all velocity components. The solar collector arrays located 30 m east of the mast significantly modify the turbulence structure, whereas PV installations situated a few hundred metres away have only a limited influence on the turbulence measured at the mast. These findings highlight the limitations of conventional turbulence models for near-surface wind over solar infrastructure and provide improved parameterisations to support the structural design. The implications for the structural response of parabolic troughs and PV modules to such turbulence remain uncertain and require further investigation.

14 SOLAR ENERGY↗

Photoluminescence Intensity Fluctuations and Temperature-Dependent Decay Dynamics of Individual Carbon Nanotube sp 3 Defects

Recent demonstration of room temperature, telecommunication wavelength single photon generation by sp 3 defects of single wall carbon nanotubes established these defects as a new class of quantum materials. However, their practical utilization in development of quantum light sources calls for a significant improvement in their imperfect quantum yield (QY~10–30%). PL intensity fluctuations observed with some defects also need to be eliminated. Aiming toward attaining fundamental understanding necessary for addressing these critical issues, we investigate PL intensity fluctuation and PL decay dynamics of aryl sp 3 defects of (6,5), (7,5), and (10,3) single wall carbon nanotubes (SWCNTs) at temperatures ranging from 300 to 4 K. By correlating defect-state PL intensity fluctuations with change (or lack of change) in PL decay dynamics, we identified random variations in the trapping efficiency of E 11 band-edge excitons (likely resulting from the existence of a fluctuating potential barrier in the vicinity of the defect) as the mechanism mainly responsible for the defect PL intensity fluctuations. Furthermore, by analyzing the temperature dependence of PL intensity and decay dynamics of individual defects based on a kinetic model involving the trapping and detrapping of excitons by optically allowed and forbidden (bright and dark) defect states, we estimate the height of the potential barrier to be in the 3–22 meV range. Our analysis also provides further confirmation of recent DFT simulation results that the emissive sp 3 defect state is accompanied by an energetically higher-lying optically forbidden (dark) exciton state.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Boundary Layer Structures Over the Northwest Atlantic Derived From Airborne High Spectral Resolution Lidar and Dropsonde Measurements During the ACTIVATE Campaign

The Planetary Boundary Layer height (PBLH) is essential for studying PBL and ocean-atmosphere interactions. Marine PBL is usually defined to include a mixed layer (ML) and a capping inversion layer. The ML height (MLH) estimated from the measurements of aerosol backscatter by a lidar was usually compared with PBLH determined from radiosondes/dropsondes in the past, as the PBLH is usually similar to MLH in nature. However, PBLH can be much greater than MLH for decoupled PBL. Here, in this study, we evaluate the retrieved MLH from an airborne lidar (HSRL-2) by utilizing 506 co-located dropsondes during the ACTIVATE field campaign over the Northwest Atlantic from 2020 to 2022. First, we define and determine the MLH and PBLH from the temperature and humidity profiles of each dropsonde, and find that the MLH values from HSRL-2 and dropsondes agree well with each other, with a coefficient of determination of 0.66 and median difference of 18 m. In contrast, the HSRL-2 MLH data do not correspond to dropsonde-derived PBLH, with a median difference of -47 m. Therefore, we modify the current operational and automated HSRL-2 wavelet-based algorithm for PBLH retrieval, decreasing the median difference significantly to -8 m. Further data analysis indicates that these conclusions remain the same for cases with higher or lower cloud fractions, and for decoupled PBLs. These results demonstrate the potential of using HSRL-2 aerosol backscatter data to estimate both marine MLH and PBLH and suggest that lidar-derived MLH should be compared with radiosonde/dropsonde-determined MLH (not PBLH) in general.

54 ENVIRONMENTAL SCIENCES↗

Effect of cubic phase evolution on field emission properties of boron nitride island films

Field emission performance of boron nitride (BN) island films is studied in terms of cubic phase evolution in plasma-enhanced chemical vapor deposition. Fine-grained island films with large surface roughness can be grown for initial sp{sup 2}-bonded BN and subsequent cubic BN (cBN) phases by using low-energy (approx20 eV) ion bombardment. Ultraviolet photoelectron spectroscopy reveals that the electron affinity is as low as 0.3 eV for both sp{sup 2}-bonded BN and cBN phases. The evolution of cBN islands reduces the turn-on field down to around 9 V/mum and increases the current density up to 10{sup -4} A/cm{sup 2}. The emission is facilitated by the larger field enhancement due to the larger roughness and the higher conduction of cBN islands. The potential barrier height is estimated to be about 3.4 eV for emission from the Fermi level, while it is only about 0.3 eV for 'conduction band emission'.

36 MATERIALS SCIENCE↗

Tunneling conductance studies in the ion-beam sputtered CoFe/Mg/MgO/NiFe magnetic tunnel junctions

Magnetic tunnel junctions consisting of CoFe(10 nm)/Mg(1 nm)/MgO(3.5 nm)/NiFe(10 nm) are grown at room temperature using dual ion beam sputtering via in-situ shadow masking. The effective barrier thickness and average barrier height are estimated to be 3.5 nm (2.9 nm) and 0.69 eV (1.09 eV) at 290 K (70 K), respectively. The tunnel magnetoresistance value of 0.2 % and 2.3 % was observed at 290 K and 60 K, respectively. The temperature dependence of tunneling conductance revealed the presence of localized states present within the forbidden gap of the MgO barrier leading to finite inelastic spin independent tunneling contributions, which degrade the TMR value.

36 MATERIALS SCIENCE↗

ULTRA-LONG-PERIOD OSCILLATIONS IN EUV FILAMENTS NEAR TO ERUPTION: TWO-WAVELENGTH CORRELATION AND SEISMOLOGY

We investigate whether or not ultra-long-period oscillations in EUV filaments can be related to their eruption. We report new observations of long-period ({approx}10-30 hr) oscillatory motions in an apparently quiescent filament, as it crosses the solar disk in a 12 minute cadence SOHO/Extreme-Ultraviolet Imaging Telescope (EIT) 195 A uninterrupted data set. This data set is chosen to explore characteristics of the filament oscillations depending on its eruptive behavior, which is observed while the filament is still on the disk. The periods are found to increase in a near-stable regime prior to eruption. For the two sequences reported so far, we compare and link the EUV filament oscillations with pulsations in full-disk solar EUV irradiance from SOHO/CELIAS/SEM 304 A flux measurements. In intervals with stationary periods, we find that the 304 A pulsations and the 195 A filament oscillations have similar periodicities, but are phase-shifted by about a quarter of period. The two-wavelength correlation serves to show that, when the filament is the dominant dynamical feature but can no longer be tracked on the disk, the full-disk irradiance may provide a mean to identify the period increase prior to the filament eruption. We use the periods thus obtained to estimate the height increase of filaments' suspending coronal magnetic field lines, based on a magnetohydrodynamic (MHD) wave interpretation of the oscillations. The results are consistent with changes in prominence heights detected off-limb and thus support the seismological tool employed. Other interpretations connected with thermal overstability or MHD piston effect are possible. These theoretical predictions however do not explain the quarter-period shift between the two EUV-wavelength signals. In any case, the detected variations may provide a powerful diagnostic tool for the forecasting of prominence eruptions.

99 GENERAL AND MISCELLANEOUS↗

PULSAR HIGH ENERGY EMISSIONS FROM OUTER GAP ACCELERATOR CLOSED BY A MAGNETIC PAIR-CREATION PROCESS

We discuss outer gap closure mechanism in the trans-field direction with the magnetic pair-creation process near the stellar surface. The gap closure by the magnetic pair creation is possible if some fraction of the pairs are produced with an outgoing momentum. By assuming that multiple magnetic field will affect the local field near the stellar surface, we show a specific magnetic field geometry near the stellar surface resulting in the outflow of the pairs. Together with the fact that the electric field is weak below null charge surface, the characteristic curvature photon energy emitted by incoming particles, which were accelerated in the outer gap, decreases drastically to {approx}100 MeV near the stellar surface. We estimate the height measured from the last-open field line, above which 100 MeV photons are converted into pairs by the magnetic pair creation. We also show the resultant multiplicity due to the magnetic pair-creation process could acquire M{sub e}{sup {+-}{approx}1}0{sup 4}-10{sup 5}. In this model, the fractional outer gap size is proportional to P {sup -1/2}. The predicted {gamma}-ray luminosity (L {sub {gamma}}) and the characteristic curvature photon energy (E{sub c}) emitted from the outer gap are proportional to B {sup 2} P {sup -5/2} and B {sup 3/4} P {sup -1}, respectively. This model also predicts that L {sub {gamma}} and E{sub c} are related to the spin-down power (L {sub sd}) or the spin-down age of pulsars ({tau}) as L {sub {gamma}} {proportional_to} L {sup 5/8} {sub sd} or L {sub {gamma}} {proportional_to} {tau}{sup -5/4} and E{sub c} {proportional_to} L {sup 1/4} {sub sd} or E{sub c} {proportional_to} {tau}{sup -1/2}, respectively.

79 ASTRONOMY AND ASTROPHYSICS↗

A LiDAR–optical data fusion approach for identifying and measuring small stream impoundments and dams

This article outlines a semi-autonomous approach for using a fusion of light detection and ranging (LiDAR) and optical remote sensing data to identify and measure small impoundments (SIs) and their dams. Quantifying such water bodies as hydrologic network features is critical for ecosystem and species conservation, emergency management, and water resource planning; however, such features are incompletely mapped at national and state levels. By merging an airborne LiDAR-derived point cloud with a normalized water index using airborne optical imagery we demonstrate an improvement upon single-source methods for identifying these water bodies; classification accuracies increased over 10% by using this multi-source fusion method. Furthermore, the method presented here illustrates a cost-effective pathway to improve the National Inventory of Dams (NID) and includes a framework for estimating dam heights, with results showing strong correlations between derived dam heights and those recorded in the NID (r=.78). With the steady increase in available LiDAR coverage, the 87,000+ dams in the NID could be updated using this technique, a method which could also be expanded for global inventories of SIs and dams.

47 OTHER INSTRUMENTATION↗

Analysis of Doppler Lidar Data Acquired During the Pentagon Shield Field Campaign

Observations from two coherent Doppler lidars deployed during the Pentagon Shield field campaign are analyzed in conjunction with other sensors to characterize the overall boundary-layer structure, and identify the dominant flow characteristics during the entire two-week field campaign. Convective boundary layer (CBL) heights and cloud base heights (CBH) are estimated from an analysis of the lidar signal-to-noise-ratio (SNR), and mean wind profiles are computed using a modified velocity-azimuth-display (VAD) algorithm. Three-dimensional wind field retrievals are computed from coordinated overlapping volume scans, and the results are analyzed by visualizing the flow in horizontal and vertical cross sections. The VAD winds show that southerly flows dominate during the two-week field campaign. Low-level jets (LLJ) were evident on all but two of the nights during the field campaign. The LLJs tended to form a couple hours after sunset and reach maximum strength between 03 and 07 UTC. The surface friction velocities show distinct local maxima during four nights when strong LLJs formed. Estimates of the convective boundary layer height and residual layer height are obtained through an analysis of the vertical gradient of the lidar signal-to-noise-ratio (SNR). Strong minimum in the SNR gradient often develops just above the surface after sunrise. This minimum is associated with the developing CBL, and increases rapidly during the early portion of the daytime period. On several days, this minimum continues to increase until about sunset. Secondary minima in the SNR gradient were also observed at higher altitudes, and are believed to be remnants of the CBL height from previous days, i.e. the residual layer height. The dual-Doppler analysis technique used in this study makes use of hourly averaged radial velocity data to produce three-dimensional grids of the horizontal velocity components, and the horizontal velocity variance. Visualization of horizontal and vertical cross sections of the dual-Doppler wind retrievals often indicated a jet-like flow feature over the Potomac River under southerly flow conditions. This linear flow feature is roughly aligned with the Potomac River corridor to the south of the confluence with the Anatostia River, and is most apparent at low levels (i.e. below ~150 m MSL). It is believed that this flow arises due to reduced drag over the water surface and when the large scale flow aligns with the Potomac River corridor. A so-called area-constrained VAD analysis generally confirmed the observations from the dual-Doppler analysis. When the large scale flow is southerly, wind speeds over the Potomac River are consistently larger than the at a site just to the west of the river for altitudes less than 100 m MSL. Above this level, the trend is somewhat less obvious. The data suggest that the depth of the wind speed maximum may be reduced by strong directional shear aloft.

54 ENVIRONMENTAL SCIENCES↗

Metrology of a Focusing Capillary Using Optical Ptychography

The focusing property of an ellipsoidal monocapillary has been characterized using the ptychography method with a 405 nm laser beam. The recovered wavefront gives a 12.5×10.4μm 2 focus. The reconstructed phase profile of the focused beam can be used to estimate the height error of the capillary surface. The obtained height error shows a Gaussian distribution with a standard deviation of 1.3 μm. This approach can be used as a quantitative tool for evaluating the inner functional surfaces of reflective optics, complementary to conventional metrology methods.

36 MATERIALS SCIENCE↗

High-Throughput Field Plant Phenotyping: A Self-Supervised Sequential CNN Method to Segment Overlapping Plants

High-throughput plant phenotyping—the use of imaging and remote sensing to record plant growth dynamics—is becoming more widely used. The first step in this process is typically plant segmentation, which requires a well-labeled training dataset to enable accurate segmentation of overlapping plants. However, preparing such training data is both time and labor intensive. To solve this problem, we propose a plant image processing pipeline using a self-supervised sequential convolutional neural network method for in-field phenotyping systems. This first step uses plant pixels from greenhouse images to segment nonoverlapping in-field plants in an early growth stage and then applies the segmentation results from those early-stage images as training data for the separation of plants at later growth stages. The proposed pipeline is efficient and self-supervising in the sense that no human-labeled data are needed. We then combine this approach with functional principal components analysis to reveal the relationship between the growth dynamics of plants and genotypes. We show that the proposed pipeline can accurately separate the pixels of foreground plants and estimate their heights when foreground and background plants overlap and can thus be used to efficiently assess the impact of treatments and genotypes on plant growth in a field environment by computer vision techniques. This approach should be useful for answering important scientific questions in the area of high-throughput phenotyping.

59 BASIC BIOLOGICAL SCIENCES↗

Inclusion of biomass burning in WRF-Chem: Impact of wildfires on weather forecasts

A plume rise algorithm for wildfires was included in WRF-Chem, and applied to look at the impact of intense wildfires during the 2004 Alaska wildfire season on weather forecasts using model resolutions of 10km and 2km. Biomass burning emissions were estimated using a biomass burning emissions model. In addition, a 1-D, time-dependent cloud model was used online in WRF-Chem to estimate injection heights as well as the final emission rates. It was shown that with the inclusion of the intense wildfires of the 2004 fire season in the model simulations, the interaction of the aerosols with the atmospheric radiation led to significant modifications of vertical profiles of temperature and moisture in cloud-free areas. On the other hand, when clouds were present, the high concentrations of fine aerosol (PM2.5) and the resulting large numbers of Cloud Condensation Nuclei (CCN) had a strong impact on clouds and microphysics, with decreased precipitation coverage and precipitation amounts during the first 12 hours of the integration, but significantly stronger storms during the afternoon hours.

09 BIOMASS FUELS↗

Comparison of planetary boundary layer height from ceilometer with ARM radiosonde data

Abstract. Ceilometer measurements of aerosol backscatter profiles have been widely used to provide continuous planetary boundary layer height (PBLHT) estimations. To investigate the robustness of ceilometer-estimated PBLHT under different atmospheric conditions, we compared ceilometer- and radiosonde-estimated PBLHTs using multiple years of U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) ceilometer and balloon-borne sounding data at ARM fixed-location atmospheric observatories and from ARM mobile facilities deployed around the world for various field campaigns. These observatories cover from the tropics to the polar regions and over both ocean and land surfaces. Statistical comparisons of ceilometer-estimated PBLHTs from the Vaisala CL31 ceilometer data with radiosonde-estimated PBLHTs from the ARM PBLHT-SONDE Value-added Product (VAP) are performed under different atmospheric conditions including stable and unstable atmospheric boundary layer, low-level cloud-free conditions, and cloudy conditions at these ARM observatories. Under unstable conditions, good comparisons are found between ceilometer- and radiosonde-estimated PBLHTs at ARM low- and mid-latitude land observatories. However, it is still challenging to obtain reliable PBLHT estimations over ocean surfaces even using radiosonde data. Under stable conditions, ceilometer- and radiosonde-estimated PBLHTs have weak correlations. We compare different PBLHT estimations utilizing the Heffter, the Liu–Liang, and the bulk Richardson number methods applied to radiosonde data with ceilometer-estimated PBLHT. We find that ceilometer-estimated PBLHT compares better with the Liu–Liang method under unstable conditions and compares better with the bulk Richardson number method under stable conditions.

54 ENVIRONMENTAL SCIENCES↗

Observations of wind farm wake recovery at an operating wind farm

Abstract. The interplay of momentum surrounding wind farms significantly influences wake recovery, affecting the speed at which wakes return to their freestream velocities. Under stable atmospheric conditions, wind farm wakes can extend over considerable distances, leading to sustained vertical momentum flux downstream, with variations observed throughout the diurnal cycle. Particularly in regions such as the US Great Plains, stable conditions can induce low-level jets (LLJs), impacting wind farm performance and power output. This study examines the implications of wake recovery using long-term observations of vertical momentum flux profiles across diverse atmospheric conditions. In these observations, several key findings were observed, such as (a) LLJ heights being altered downstream of a wind farm, especially when the LLJs are below 250 m above ground level; (b) a notable impact of LLJ height on wake recovery being observed using momentum flux profiles at upwind and downwind locations, wherein LLJs between 250 and 500 m above ground level resulted in larger momentum transfer within the wake (i.e., smaller velocity deficit) compared to LLJs below 250 m above ground level; (c) the largest momentum flux variability being observed during stable atmospheric conditions, with non-negligible variability observed during neutral and unstable atmospheric conditions; (d) detection of wake effects almost always being observed throughout the atmospheric boundary layer height; and finally (e) enhancement of wake recovery being observed in the presence of propagating gravity waves. These insights deepen our understanding of the intricate dynamics governing wake recovery in wind farms, advancing efforts to model and predict their behavior across varying atmospheric contexts. In addition, the performance of large-eddy-simulation-based semi-empirical internal boundary layer height model estimates incorporating real-world atmospheric and turbine inputs was evaluated using observations during LLJ conditions.

17 WIND ENERGY↗

Two-dimensional Gaussian processes applied to the determination of contact between lubricated rolling surfaces

The effectiveness of a lubricant film preventing metallic contact between two rolling surfaces (such as in ball bearings) as a function of surface roughness parameters was investigated. The parameters considered are the spectral moments of the two-dimensional surface obtained by superposition of the two rolling surfaces. The peak height distribution, estimation of one-dimensional profile spectral moments, and the estimation of two-dimensional surface moments from several profile measurements were considered. Also given is an asymptotic relation between the mean film thickness and contact occurrences.

Sidik, S. M.↗

Two-dimensional Gaussian processes applied to the determination of contact between lubricated rolling surfaces

Theoretical investigation of how effectively a lubricant film prevents metallic contact between two rolling surfaces (such as in ball bearings) as a function of surface roughness parameters. The parameters considered are the spectral moments of the two-dimensional surface obtained by superposition of the two rolling surfaces. We consider the peak height distribution, estimation of one-dimensional profile spectral moments, and the estimation of two-dimensional surface moments from several profile measurements are taken into account. Also given is an asymptotic relation between the mean film thickness and contact occurrences.

Sidik, S. M.↗

Sea surface determination from space: The GSFC geoid

The determination of the sea surface/geoid and its relative variation were investigated and results of the altimeter experiment on Skylab to test the geoid are discussed. The spaceborne altimeter on Skylab revealed that the sea surface of the world's oceans can be measured with an accuracy in the meter range. Surface variations are discussed as they relate to those computed from satellite orbital dynamics and ground based gravity data. The GSFC geoid was constructed from about 400,000 satellite tracking data (range, range rate, angles) and about 20,000 ground gravity observations. One of the last experiments on Skylab was to measure and/or test this geoid over almost one orbit. It was found that the computed water surface deviates between 5 to 20 m from the measured one. Further outlined are the influence of orbital errors on the sea surface, and numerical examples are given based upon real tracking data. Orbital height error estimates were computed for geodetic type satellites and are found to be in the order of 0.2 to 5 meters.

Vonbun, F. O.↗

Wetland physical and biotic studies using multispectral data

A November 1982 Landsat-4 TM scene and March and September 1984 airborne L-band radar data for a brackish-wetland area of the Blackwater National Wildlife Refuge (near Chesapeake Bay) are analyzed to monitor changes in vegetation and water area. The accuracy of level-I classification of the TM image is found to be 81 percent, but that of the few level-II/III classes for which ground truth was available is only 53 percent. The value of radar images for discriminating water areas obscured by vegetation and estimating plant heights is indicated.

Ormsby, J. P.↗