SEARCH · Search NASA

Results for “helicity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Tone noise of three supersonic helical tip speed propellers in a wind tunnel at 0.8 Mach number

Three supersonic helical tip speed propellers were tested in the NASA Lewis 8- by 6-foot wind tunnel. Noise data were obtained while these propellers were operating at a simulated cruise condition. The walls of this tunnel were not acoustically treated and therefore this was not an ideal location for taking noise data, but it was thought that the differences in noise among the three propellers would be meaningful. The straight bladed propeller which did not incorporate sweep was the noisiest with the aerodynamically swept propeller only slightly quieter. However, the acoustically swept propeller was significantly quieter than the straight propeller, thereby indicating the merit of this design technique.

Dittmar, J. H.↗

NASA NTRS1981

Automatic helical rotorcraft descent and landing using a Microwave Landing System

A helical-approach concept is presented for Instrument Flight Rules (IFR) operation of rotorcraft into congested terminal areas where separation from high-speed jet traffic is highly desirable and the airport-precision-approach aid is a Microwave Landing System (MLS). The concept takes advantage of the fact that rotorcraft need not land on the main runway but can operate from a pad that lies on an MLS radial offset from the centerline. The results of 48 flights using a UH-1H helicopter and a research avionics system are presented. Three levels of navigation sophistication were also investigated. It is shown that an approach helix can be contained in a relatively small volume and that being within the Instrument Landing System (ILS) Category II window at a 30-m (100-ft) altitude is not a requirement for a successful hover over a landing pad. Only two of the three navigation systems provided estimates that allowed all flights to descend from hover to touchdown.

Mcgee, L. A.↗

NASA NTRS1981

The three-dimensional boundary layer on a rotating helical blade

The laminar boundary layer on a twisted helical blade is considered. The blade geometry is the same as that proposed by Horlock and Wordsworth (1965). However, the blade is twisted about the leading edge in the manner described by Miyake and Fujita (1974). The flow may be considered to be the analog, in a rotating reference frame, of the flat-plate boundary layer in a stationary frame. It is shown that a coordinate system which is orthogonal in the blade surface may be developed. With the appropriate scaling of the dependent variables a solution for the boundary layer flow is readily obtained. The systems of ordinary differential equations for the stream function of the primary flow and the cross-flow are solved numerically.

Morris, P. J.↗

NASA NTRS1981

Determination of magnetic helicity in the solar wind and implications for cosmic ray propagation

Magnetic helicity (Hm) is the mean value of the correlation between a turbulent magnetic field and the magnetic vector potential. A technique is described for determining Hm and its 'reduced' spectrum from the two point magnetic correlation matrix. The application of the derived formalism to solar wind magnetic fluctuations is discussed, taking into account cases for which only single point measurements are available. The application procedure employs the usual 'frozen in approximation' approach. The considered method is applied to an analysis of several periods of Voyager 2 interplanetary magnetometer data near 2.8 AU. During these periods the correlation length, or energy containing length, was found to be approximately 3 x 10 to the 11th cm

Matthaeus, W. M.↗

NASA NTRS1984

High-Temperature Helical-Tube Solar Receiver

Solar-thermal receiver used with circular parabolic concentrator to supply about 58 kW thermal power to Brayton engine or industrial process. Solar radiation focused into open end of cylindrical ceramic thermal inertial sleeve 8 in. in diameter that reradiates energy to helical heatexchanger tube surrounding sleeve.

Robertson, C. S., Jr.↗

NASA NTRS1982

Molecular structure of r/GCG/d/TATACGC/ - A DNA-RNA hybrid helix joined to double helical DNA

The molecule r(GCG)d(TATACGC) is self-complementary and forms two DNA-RNA hybrid segments surrounding a central region of double helical DNA; its molecular structure has been solved by X-ray analysis. All three parts of the molecule adopt a conformation which is close to that seen in the 11-fold RNA double helix. The conformation of the ribonucleotides is partly determined by water molecules bridging between the ribose O2' hydroxyl group and cytosine O2. The hybrid-DNA duplex junction contains no structural discontinuities. However, the central DNA TATA sequence has some structural irregularities.

Wang, A. H.-J.↗

NASA NTRS1982

The velocity field induced by a helical vortex filament

An exact analytical solution for the velocity field, both interior and exterior, induced by an infinite right-handed helical vortex filament is derived. Due to the way the variables combine in this solution, the paper also shows that it is possible to derive a stream function for this nonaxisymmetric flow. Sample calculations of these expressions are included.

Hardin, J. C.↗

NASA NTRS1983

A possible explanation for the present difference between linear noise theory and experimental data for supersonic helical tip speed propellers

High speed turboprops are attractive candidates for future aircraft because of their high propulsive efficiency. However, the noise of their propellers may create a cabin environment problem for the aircraft powered by these propellers. The noise of some propeller models was measured, and predictions of the noise using a method based on the Ffowcs Williams-Hawkins equation were made. The predictions and data agree well at lower helical tip Mach numbers but deviate above Mach 1.0. Some possible reasons why the theory does not predict the data and focuses on improvement of the aerodynamic inputs as the most likely remedy are investigated. In particular, it is proposed that an increase in the drag and a decrease in the lift near the tip of the blade where the majority of the noise is generated, is warranted in the input to the theory.

Dittmar, J. H.↗

NASA NTRS1984

International test and demonstration of a 1-MW wellhead generator: Helical screw expander power plant

A 1-MW wellhead generator was tested in 1980, 1981, and 1982 by Mexico, Italy, and New Zealand at Cerro Prieto, Cesano, and Broadlands, respectively. The total flow helical screw expander portable power plant, Model 76-1, had been built for the U.S. Government and field-tested in Utah, USA, in 1978 and 1979. The expander had oversized internal clearances designed for self-cleaning operation on fluids that deposit adherent scale normally detrimental to the utiliation of liquid dominated fields. Conditions with which the expander was tested included inlet pressures of 64 to 220 psia, inlet qualities of 0% to 100%, exhaust pressures of 3.1 to 40 psia, electrial loads of idle and 110 to 933 kW, electrical frequencies of 50 and 60 Hz, male rotor speeds of 2500 to 4000 rpm, and fluid characteristics to 310,000 ppm total dissolved solids and noncondensables to 38 wt % of the vapor. Some testing was done on-grid. Typical expander isentropic efficiency was 40% to 50% with the clearances not closed, and 5 percentage points or more higher with the clearances partly closed. The expander efficiency increased approximately logarithmically with shaft power for most operations, while inlet quality, speed, and pressure ratio across the machine had only small effects. These findings are all in agreement with the Utah test results.

Mckay, R. A.↗

NASA NTRS1985

Aerodynamic analysis of a horizontal axis wind turbine by use of helical vortex theory, volume 2: Computer program users manual

A description of a computer program entitled VORTEX that may be used to determine the aerodynamic performance of horizontal axis wind turbines is given. The computer code implements a vortex method from finite span wind theory and determines the induced velocity at the rotor disk by integrating the Biot-Savart law. It is assumed that the trailing helical vortex filaments form a wake of constant diameter (the rigid wake assumption) and travel downstream at the free stream velocity. The program can handle rotors having any number of blades which may be arbitrarily shaped and twisted. Many numerical details associated with the program are presented. A complete listing of the program is provided and all program variables are defined. An example problem illustrating input and output characteristics is solved.

Keith, T. G., Jr.↗

NASA NTRS1986

New generation methods for spur, helical, and spiral-bevel gears

New methods for generating spur, helical, and spiral-bevel gears are proposed. These methods provide the gears with conjugate gear tooth surfaces, localized bearing contact, and reduced sensitivity to gear misalignment. Computer programs have been developed for simulating gear meshing and bearing contact.

Litvin, F. L.↗

NASA NTRS1987

Numerical simulation of transonic propeller flow using a 3-dimensional small disturbance code employing novel helical coordinates

The numerical simulation of three-dimensional transonic flow about propeller blades is discussed. The equations for the unsteady potential flow about propellers is given for an arbitrary coordinate system. From this the small disturbance form of the equation is derived for a new helical coordinate system. The new coordinate system is suited to propeller flow and allows cascade boundary conditions to be applied straightforward. A numerical scheme is employed which solves the steady flow as an asymptotic limit of unsteady flow. Solutions are presented for subsonic and transonic flow about a 5 percent thick bicircular arc blade of an eight bladed cascade. Both high and low advance ratio cases are given which include a lifting case as well as nonlifting cases. The nonlifting cases are compared to solutions from a Euler code.

Snyder, Aaron↗

NASA NTRS1987

Helical gears with circular arc teeth: Generation, geometry, precision and adjustment to errors, computer aided simulation of conditions of meshing and bearing contact

The authors have proposed a method for the generation of circular arc helical gears which is based on the application of standard equipment, worked out all aspects of the geometry of the gears, proposed methods for the computer aided simulation of conditions of meshing and bearing contact, investigated the influence of manufacturing and assembly errors, and proposed methods for the adjustment of gears to these errors. The results of computer aided solutions are illustrated with computer graphics.

Litvin, Faydor L.↗

NASA NTRS1987

Numerical simulation of transonic propeller flow using a three-dimensional small disturbance code employing novel helical coordinates

Snyder, Aaron↗

NASA NTRS1987

New generation methods for spur, helical, and spiral-bevel gears

Litvin, F. L.↗

NASA NTRS1987

Torsion effect on fully developed flow in a helical pipe

Two techniques, a series expansion method of perturbed Poiseuille flow valid for low Dean numbers and a solution of the complete Navier-Stokes equation applicable to intermediate Dean values, are used to investigate the torsion effect on the fully developed laminar flow in a helical pipe of constant circular cross section. For the secondary flow patterns, the results show that the presence of torsion can produce a significant effect if the ratio of the curvature to the torsion is of order unity. The secondary flow is distorted in these cases. It is noted that the torsion effect is, however, usually small, and that the secondary flow has the usual pattern of a pair of counter-rotating vortices of nearly equal strength.

Kao, Hsiao C.↗

NASA NTRS1987

High-efficiency helical traveling-wave tube with dynamic velocity taper and advanced multistage depressed collector

A NASA-sponsored research and development contract has been established with the Watkins-Johnson Company to fabricate high-efficiency 20-watt helical traveling wave tubes (TWTs) operating at 8.4 to 8.43 GHz. The TWTs employ dynamic velocity tapers (DVTs) and advanced multistage depressed collectors (MDCs) having electrodes with low secondary electron emission characteristics. The TWT designs include two different DVTs; one for maximum efficiency and the other for minimum distortion and phase shift. The MDC designs include electrodes of untreated and ion-textured graphite as well as copper which has been treated for secondary electron emission suppression. Objectives of the program include achieving at least 55 percent overall efficiency. Tests with the first TWTs (with undepressed collectors) indicate good agreement between predicted and measured RF efficiencies with as high as 30 percent improvement in RF efficiency over conventional helix designs.

Curren, Arthur N.↗

NASA NTRS1988

General magnetic reconnection, parallel electric fields, and helicity

This paper considers the concept of magnetic reconnection from a general point of view, with special consideration given to magnetic reconnection in nonvanishing magnetic fields, i.e., finite-B reconnection as distinct from zero-B reconnection. It is shown that the electric field component parallel to the magnetic field (E-parallel) plays a crucial physical role in finite-B reconnection. Two theorems involving E-parallel are proposed. The first defines a necessary and sufficient condition of E-parallel for global reconnection to occur. The second theorem is concerned with the change of magnetic helicity to E-parallel for cases where the electric field vanishes at large distances. The general magnetic reconnection concept is tested by applying it to the process of plasmoid formation process.

Schindler, K.↗