SEARCH · Search NASA

Results for “high useful yield”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Multiplicity and event-scale dependent flow and jet fragmentation in pp collisions at $\sqrt{s}$ = 13 TeV and in p–Pb collisions at $\sqrt{s_{\textrm{NN}}}$ = 5.02 TeV

Long- and short-range correlations for pairs of charged particles are studied via two-particle angular correlations in pp collisions at $\sqrt{s}$ = 13 TeV and p–Pb collisions at $\sqrt{s_{\textrm{NN}}}$ = 5.02 TeV. The correlation functions are measured as a function of relative azimuthal angle Δφ and pseudorapidity separation Δη for pairs of primary charged particles within the pseudorapidity interval |η| < 0.9 and the transverse-momentum interval 1 < p T < 4 GeV/c. Flow coefficients are extracted for the long-range correlations (1.6 < |Δη| < 1.8) in various high-multiplicity event classes using the low-multiplicity template ft method. The method is used to subtract the enhanced yield of away-side jet fragments in high-multiplicity events. These results show decreasing flow signals toward lower multiplicity events. Furthermore, the flow coefficients for events with hard probes, such as jets or leading particles, do not exhibit any significant changes compared to those obtained from high-multiplicity events without any specific event selection criteria. The results are compared with hydrodynamic-model calculations, and it is found that a better understanding of the initial conditions is necessary to describe the results, particularly for low-multiplicity events.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS2015

Experimental and Finite Element Modeling of Near-Threshold Fatigue Crack Growth for the K-Decreasing Test Method

The experimental methods to determine near-threshold fatigue crack growth rate data are prescribed in ASTM standard E647. To produce near-threshold data at a constant stress ratio (R), the applied stress-intensity factor (K) is decreased as the crack grows based on a specified K-gradient. Consequently, as the fatigue crack growth rate threshold is approached and the crack tip opening displacement decreases, remote crack wake contact may occur due to the plastically deformed crack wake surfaces and shield the growing crack tip resulting in a reduced crack tip driving force and non-representative crack growth rate data. If such data are used to life a component, the evaluation could yield highly non-conservative predictions. Although this anomalous behavior has been shown to be affected by K-gradient, starting K level, residual stresses, environmental assisted cracking, specimen geometry, and material type, the specifications within the standard to avoid this effect are limited to a maximum fatigue crack growth rate and a suggestion for the K-gradient value. This paper provides parallel experimental and computational simulations for the K-decreasing method for two materials (an aluminum alloy, AA 2024-T3 and a titanium alloy, Ti 6-2-2-2-2) to aid in establishing clear understanding of appropriate testing requirements. These simulations investigate the effect of K-gradient, the maximum value of stress-intensity factor applied, and material type. A material independent term is developed to guide in the selection of appropriate test conditions for most engineering alloys. With the use of such a term, near-threshold fatigue crack growth rate tests can be performed at accelerated rates, near-threshold data can be acquired in days instead of weeks without having to establish testing criteria through trial and error, and these data can be acquired for most engineering materials, even those that are produced in relatively small product forms.

Smith, Stephen W.↗

NASA NTRS1973

The use of photographic methods in contrast enhancement of ERTS-1 images

The contrast of ERTS 70mm positive images can be enhanced to varying degrees by rephotographing the images with different types of negative films, and by overdeveloping the films with different developers. A combination of high contrast copy film (Kodak 5069) and a high energy developer (Kodak D-11) yields high contrast. Still greater contrast may be otbained by using a film of higher contrast capability and a developer of higher energy capability. Contrast can also be enhanced in the printing process with the use of highcontrast photographic papers, or with the use of polycontrast photographic paper and filters. Contrast enhancement by photocopying delineates topographic boundaries and may aid in the objective measurement of topographic parameters.

Harris, L. F.↗

DOE OSTI2022

Atomic Force Microscope Active Optical Probe for Single-Molecule Imaging and Time-Resolved Optical Spectroscopy (DOE SBIR Phase II/IIA Final Report)

Actoprobe LLC reports on the results of its DOE SBIR Phase II/IIA project on the development of Atomic Force Microscope Active Optical Probe for Single-Molecule Imaging and Time-Resolved Optical Spectroscopy. While chemistry science and technology greatly benefit from Atomic Force Microscopy in surface characterization, time-resolved chemical imaging on the single-molecule level lags far behind. Current scanning probe microscopy only obtains information about mechanical but not optical/chemical properties. To address this problem, the Actoprobe LLC research team has proposed a novel class of Atomic Force Microscopy probes, Ultra-Fast Pulsed Active Atomic Force Microscopy Optical Probes (UFP AAOPs), that will allow ultrafast time-resolved optical and chemical imaging at the nanoscale. As envisioned, these unique optical probes will perform the functions of conventional Atomic Force Microscopy probes and, in addition, will simultaneously provide chemical information about molecular scale interactions. This innovation is accomplished by integrating an ultrafast pulsed Quantum Dot laser source into an Atomic Force Microscopy probe. This report describes our progress with the fabrication of an ultrafast micrometer-size semiconductor laser, based on “artificial atoms” - Quantum Dots, integrated with an Atomic Force Microscopy probe. In this Phase II/IIA project, we have demonstrated the feasibility of the UFP AAOP concept by fabricating a first prototype of the UFP AAOP. The excellent performance of the probe has been proven in terms of AFM and optical spatial resolution through rigorous tests. The UFP AAOP provides pulses with less than 4 ps duration and higher than 11 GHz repetition rate, and spatial resolution better than 300 nm at 1240 nm wavelength. Technically, it is possible to reduce the pulse width to less than 1 ps and to improve lateral resolution to ~ 0.5 nm, which implies the potential capability for the probe to characterize chemical compounds with single-molecule resolution. The UFP AAOP fabrication procedure has been developed for wafer-scale production of multiple devices, with the yield of the process estimated to be lower than 1% with the limited fabrication capabilities and equipment available for use in the research project. However, using high-volume production tools and special GaAs processing equipment, the yield can be significantly improved, theoretically to ~ 50%. Finally, economic feasibility and scale-up manufacturing potential were analyzed for UFP AAOP and found to be very promising. In summary, the Actoprobe team has successfully demonstrated the feasibility of the UFP AAOP concept.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Performance of borated scintillator screens for high-resolution neutron imaging

The most commonly used screens for neutron imaging consist of 6 LiF + ZnS. This type of screen yields the highest light output per detected neutron. For high resolution, gadolinium oxysulfide (GOS, Gadox) screens are employed, which have a much higher detection efficiency, but a light output so much lower than LiF + ZnS that measurements are often limited by photon statistics. Historically, screens using boron as a neutron-sensitive material have not been very successful. However, a new preparation method was introduced recently that produces light output higher than Gadox with detection efficiency greater than LiF + ZnS. Measurements of these new borated screens were performed at the NeXT facility at ILL, Grenoble, in comparison to a high resolution Gadox screen.

10B↗

DOE OSTI2025

Autonomous organic synthesis for redox flow batteries via flexible batch Bayesian optimization

Traditional trial-and-error methods for materials discovery are inefficient to meet the urgent demands posed by the rapid progression of climate change. This urgency has driven the increasing interest in integrating robotics and machine learning into materials research to accelerate experimental learning. However, idealized decision-making frameworks to achieve maximum sampling efficiency are not always compatible with high-throughput experimental workflows inside a laboratory. For multi-step chemical processes, differences in hardware capacities can complicate the digital framework by introducing constraints on the maximum number of samples in each step of the experiment, hence causing varying batch sizes in variable selection within the same batch. Therefore, designing flexible sampling algorithms is necessary to accommodate the multi-step synthesis with practical constraints unique to each high-throughput workflow. In this work, we designed and employed three strategies on a high-throughput robotic platform to optimize the sulfonation reaction of redox-active molecules used in flow batteries. Our strategies adapt to the multi-step experimental workflow, where their formulation and heating steps are separate, causing varying batch size requirements. By strategically sampling using clustering and mixed-variable batch Bayesian optimization, we were able to iteratively identify optimal conditions that maximize the yields. Our work presents a flexible approach that allows tailoring the machine learning decision-making to suit the practical constraints in individual high-throughput experimental platforms, followed by performing resource-efficient yield optimization using available open-source Python libraries.

Tamura, Clara [Univ. of Washington, Seattle, WA (U↗

DOE OSTI2022

Technical Guidance on Use of the Linseis Vertical Dilatometer L75

Linseis vertical Dilatometer L75 thermal expansion equipment is a complete system which can be used for measuring change of the absolute length of a sample, determination of the thermal expansion coefficient (CTE), shrinkage, and sintering. The 238 Pu Supply Program is interested in re-establishing the capability to determine CTE and measuring the change of the absolute length of various 237 Np Al/cermet samples during heating. The change in length of the measured sample is recorded using a highly sensitive Linear Variable Differential Transformer (LVDT). The dilatometer is user-friendly and simple to operate which will allow technicians to be trained easily on its use. This equipment was designed to be used specifically for ceramics. It has a highly vacuum tight push rod dilatometer, a high-resolution inductive transducer using innovative and comprehensive temperature controls which provide excellent performance as a measurement system yielding high accuracy, reproducibility, and long-term stability.

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2021

Soybean fallow and nitrification inhibitors: Strategies to reduce N 2 O emission intensities and N losses in Australian sugarcane cropping systems

The Australian sugar industry is facing mounting pressure to reduce the nitrogen (N) losses and nitrous oxide (N 2 O) emissions associated with N fertiliser use. Research has shown that N 2 O emissions from sugarcane (Saccharum officinarum L.) cropping systems can be reduced with the use of fertilisers coated with nitrification inhibitors, or by sowing legume crops in the fallows between sugarcane crop cycles. However, the efficacy of these two N management strategies across different climatic zones is still unclear, as results from field studies have been contradictory. The objectives of this study were therefore to use the DayCent model to assess the long-term effects of the two strategies (separately or in combination) on N 2 O emissions, N losses and yields. The model was parameterised using data from eight field experiments (39 treatments) conducted across four of the five main districts of the Australian sugarcane industry. A series of long-term scenarios embracing a range of N fertiliser rates (0- 160 kg N ha -1 applied as urea), climatic regions (Tropics and Subtropics), soil textures (fine- and coarse-textured soils) and N-loss risk scenarios (crop fertilised well before or close to the on-set of the wet season) were tested for both N management strategies. Simulations identified that the combined use of soybean (Glycine max L.) fallows and N fertiliser coated with the 3,4-dimethylpyrazole phosphate (DMPP) nitrification inhibitor was the most effective strategy to maintain or even increase current yields while significantly reducing N 2 O and cumulative N (mainly due to nitrate) losses. When used alone, the soybean fallow strategy on average reduced N losses over the entire crop cycle by 29 % compared with current industry best practice. However, this strategy showed a limited capacity to reduce N 2 O emissions over the entire cane crop cycle (median: -3% compared with current industry best practice), or even increased them in scenarios at high-risk of N losses in the Tropics. The use of urea coated with DMPP alone allowed current fertiliser N rates to be reduced by 30 % without any substantial yield penalty. In environments prone to high N losses, DMPP urea abated overall N losses and N 2 O emissions by 41 % and 30 %, respectively. This was the first study to use such an extensive dataset to parameterise a biogeochemical model for yields, N 2 O emissions and N losses in sugarcane cropping systems. Finally, the findings will be instrumental in guiding future research and policies designed to improve the profitability and environmental sustainability of this industry.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2004

Thermally Conductive Metal-Tube/Carbon-Composite Joints

An improved method of fabricating joints between metal and carbon-fiber-based composite materials in lightweight radiators and heat sinks has been devised. Carbon-fiber-based composite materials have been used in such heat-transfer devices because they offer a combination of high thermal conductivity and low mass density. Metal tubes are typically used to carry heat-transfer fluids to and from such heat-transfer devices. The present fabrication method helps to ensure that the joints between the metal tubes and the composite-material parts in such heat-transfer devices have both (1) the relatively high thermal conductances needed for efficient transfer of heat and (2) the flexibility needed to accommodate differences among thermal expansions of dissimilar materials in operation over wide temperature ranges. Techniques used previously to join metal tubes with carbon-fiber-based composite parts have included press fitting and bonding with epoxy. Both of these prior techniques have been found to yield joints characterized by relatively high thermal resistances. The present method involves the use of a solder (63 percent Sn, 37 percent Pb) to form a highly thermally conductive joint between a metal tube and a carbon-fiber-based composite structure. Ordinarily, the large differences among the coefficients of thermal expansion of the metal tube, solder, and carbon-fiber-based composite would cause the solder to pull away from the composite upon post-fabrication cooldown from the molten state. In the present method, the structure of the solder is modified (see figure) to enable it to deform readily to accommodate the differential thermal expansion.

Copeland, Robert J.↗

NASA NTRS2024

Global Nitrogen Needs to Improve Wheat Yield Under Climate Change

Increasing global food demand will require more food production without further exceeding the planetary boundaries, while at the same time adapting to climate change. We used an ensemble of wheat simulation models, with improved yield traits from the highest-yielding wheat genotypes to quantify potential yield gains and associated N requirements. This was explored for current and climate change scenarios across representative sites of major world wheat producing regions. The improved yield traits increased yield by 16% with current N fertilizer applications under both current climate and mid-century climate change scenarios. To achieve the full yield potential, a 52% increase in global average yield under a mid-century high warming climate scenario (RCP8.5), fertilizer use would need to increase fourfold over current use, which would unavoidably lead to higher environmental impacts from wheat production. Our results show the need to improve soil N availability and N use efficiency, along with yield potential.

Nitrogen↗

NASA NTRS1985

Measurement and prediction of model-rotor flow fields

This paper shows that a laser velocimeter can be used to measure accurately the three-component velocities induced by a model rotor at transonic tip speeds. The measurements, which were made at Mach numbers from 0.85 to 0.95 and at zero advance ratio, yielded high-resolution, orthogonal velocity values. The measured velocities were used to check the ability of the ROT22 full-potential rotor code to predict accurately the transonic flow field in the crucial region around and beyond the tip of a high-speed rotor blade. The good agreement between the calculated and measured velocities established the code's ability to predict the off-blade flow field at transonic tip speeds. This supplements previous comparisons in which surface pressures were shown to be well predicted on two different tips at advance ratios to 0.45, especially at the critical 90 deg azimuthal blade position. These results demonstrate that the ROT22 code can be used with confidence to predict the important tip-region flow field, including the occurrence, strength, and location of shock waves causing high drag and noise.

Owen, F. K.↗

DOE OSTI2021

Using distributions to understand neutron and x-ray production in ICF ignition capsules and other high energy density plasmas

Here this paper describes how x-ray and neutron distribution functions can be useful tools to visualize the conditions measured in many types of plasma physics experiments. In particular, we model a standard inertial confinement fusion ignition capsule that consists of a Si doped plastic ablator surrounding a layer of deuterium–tritium (DT) ice as the yield varies from 18 kJ to 16.7 MJ and use the distribution functions to show that neutrons and high energy x rays (15 keV) are produced under similar conditions when the yield is low. However, as the capsule starts to support a propagating burn due to alpha heating, the x rays and neutrons are produced under somewhat different conditions in different parts of the plasma. In particular, the x-ray production takes place mainly in the hot plastic ablator for the full yield ignition capsule under quite different plasma conditions from the DT region producing the 14 MeV neutrons, which results in x-ray images with larger radii than the corresponding neutron images. These same distribution functions can be applied to many other plasma physics experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Advanced Algal Biofoundries for the Production of Polyurethane Precursors

The primary goal of the BEEPs project was to develop a process that could accelerate the development of algae as bioproduction platforms, from initial chemical product concept to an economically viable market supply. Under this program we elected to develop strains of algae that could generate polyurethane precursors, while simultaneously developing basic genetic tools to enable improved algal production systems. This program was specifically designed to incorporate National Laboratories as a means to utilize the expertise and facilities for new bio-production platforms. To that end, we designed a program to collaborate with the Agile BioFoundry at Lawrence Berkeley National Laboratory (LBNL) and computational platforms at Pacific Northwest National Laboratory (PNNL). In addition to these National Laboratory partners, we also had academic partners from UC Davis and Georgia Tech, as well as commercial partners Algenesis Materials and BASF. To achieve these goals, we initially focused on developing the genetic tools and high throughput screening technologies necessary to generate and assess production of polymer precursors (succinic acid) in algae and cyanobacteria, including advanced promoters and biosensors. In parallel, we computationally identified potential production bottlenecks and then used the developed genetic tools to increase production rates and yields. Constant feedback of data was used in conjunction with machine learning, high-throughput cell sorting, and synthetic biology, for additional targeted metabolic engineering. Multiple rounds of tool design, building, testing, and learning were supplied to partners at PNNL and LBNL to develop new models and tools that could expedite bioproduction platform development and increase yield performance. We targeted, and achieved, the FOA requirement yield metric of 20 g/L, as a milestone and deliverable from at least one of our engineered strains for the production of succinic acid.

09 BIOMASS FUELS↗

NASA NTRS2016

Estimates of Lightning NOx Production Based on OMI NO2 Observations Over the Gulf of Mexico

We evaluate nitrogen oxide (NO(sub x) NO + NO2) production from lightning over the Gulf of Mexico region using data from the Ozone Monitoring Instrument (OMI) aboard NASAs Aura satellite along with detection efficiency-adjusted lightning data from the World Wide Lightning Location Network (WWLLN). A special algorithm was developed to retrieve the lightning NOx [(LNO(sub x)] signal from OMI. The algorithm in its general form takes the total slant column NO2 from OMI and removes the stratospheric contribution and tropospheric background and includes an air mass factor appropriate for the profile of lightning NO(sub x) to convert the slant column LNO2 to a vertical column of LNO(sub x). WWLLN flashes are totaled over a period of 3 h prior to OMI overpass, which is the time an air parcel is expected to remain in a 1 deg. x 1 deg. grid box. The analysis is conducted for grid cells containing flash counts greater than a threshold value of 3000 flashes that yields an expected LNO(sub x) signal greater than the background. Pixels with cloud radiance fraction greater than a criterion value (0.9) indicative of highly reflective clouds are used. Results for the summer seasons during 2007-2011 yield mean LNO(sub x) production of approximately 80 +/- 45 mol per flash over the region for the two analysis methods after accounting for biases and uncertainties in the estimation method. These results are consistent with literature estimates and more robust than many prior estimates due to the large number of storms considered but are sensitive to several substantial sources of uncertainty.

Lightning↗

DOE OSTI2025

A charged particle transport approximation for thick and thin plasmas

In this work, we will construct a simple method to be utilized in the interpretation of the properties of a thin plasma from a study of the transport of charged particles through it. We do so by first demonstrating how charged particle fluxes encode local plasma information in their spectra for sufficiently thick plasmas and then propose how to extend that analysis to the thin plasma limit where the extensive geometry cannot be neglected through arguments from scale separation. We provide a numerical treatment of the transport problem and demonstrate that it is in good agreement with the approximation we present. Finally, we utilize both the numerical solution and our novel approximation to study the impact of the extensive scale of the plasma on the yield and flux normalized high-energy neutron spectra resulting from the upscattering of charged fuel ions. Using this analysis, we show that (after controlling for fusion yield) for the same uniform densities and temperatures, larger plasmas have higher magnitude but softer reaction-in-flight (RIF) neutron spectra relative to smaller plasmas. This is because larger plasmas retain more knocked-on suprathermal ions within their bulk and can downscatter them to lower average energies, while smaller plasmas allow a larger fraction of high energy particles to “range out” of the system prior to substantial downscattering or inducing an RIF reaction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Highly swollen ROMP-based gels

In this study, the leakage of organic solvent during the transportation and storage is one of the major threats to the environment. Networks/gels acting as the absorbing materials for organic solvents are the most promising solution for the organic solvent pollution. Here, we report the synthesis of highly swollen networks/gels in high yield (≥95%) via ring opening metathesis polymerization (ROMP) using Grubbs’ first generation catalyst/initiator (G1), a crosslinker (1,1'-(methylenedi-4,1-phenylene)bis-exo-7-oxanorbornenecarboximide) and monofunctional monomer/diluent (exo-N-phenyl-7-oxanorbornenecarboximide). The mesh size of the network was varied by keeping the concentration of monomer constant while changing the concentrations of crosslinker and G1 (initiator). The swelling capacity of the network in N,N-dimethylformamide (DMF) solvent increased from 41 to 53 and to 61 with the increase of theoretical mesh size (molar ratio of monomer to crosslinker) from 20 to 40 and to 60, respectively. By further increasing the mesh size from 60 to 80 there was no significant change in swelling capacities (63). Thus, the gel with the mesh size of 60 was selected for swelling capacity analysis in other polar organic solvents such as dimethyl sulfoxide (DMSO), dichloromethane (DCM), chloroform and lithium-ion battery electrolyte solution (1.0 M LiPF 6 in ethylene carbonate (EC)/diethyl carbonate (DEC) = 50/50 (v/v)). They showed the decreased swelling capacity value from 61 to 57, 40, 31 and 5, respectively. For a controlled mesh size ROMP-based gel, we observed the highest swelling capacity values to date.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Convex Decreasing Algorithms: Distributed Synthesis and Finite-Time Termination in Higher Dimension

Here we establish finite time termination algorithms for consensus algorithms based on geometric properties that yield finite-time guarantees, suited for use in high dimension and in the absence of a central authority. These pursuits motivate a new peer to peer convex hull algorithm which is utilized for one stopping algorithm. Further an alternative lightweight norm based stopping criteria is also developed. The practical utility of the algorithm is illustrated through MATLAB simulations.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2024

SQMS science advances impact on Rigetti commercial processors

The collaboration between the Superconducting Quantum Materials and Systems Center (SQMS) and Rigetti Computing produced several advancements in our understanding of the role of materials characteristics in quantum processor performance. This partnership leverages SQMS's extensive characterization infrastructure and cutting-edge research in materials, and Rigetti's expertise in quantum hardware and robust nanofabrication to improve precision and performance of Rigetti's test QPUs. Qubit frequency is determined in large part by the properties of Josephson junctions (JJs) made of amorphous oxide tunnel barriers; the Alternating-Bias Assisted Annealing (ABAA) process allows us to tune JJs to their desired frequency [1]. Work by SQMS researchers in characterizing high-precision JJs post-processed (using ABAA) have yielded crucial information on the nature of the structure and chemical bonding uniformity of the ABAA processed amorphous oxides. Performance has also been improved through a comprehensive series of experiments that tested encapsulation and surface treatment. Encapsulation of the niobium metal layer with tantalum resulted in an T1 improvement of 80%, experimentally confirming the role of Nb surface losses in qubit performance [2]. Pre-treatment of the underlying silicon surface prior to JJ fabrication by replacing a buffered oxide etch (BOE) with hydrofluoric acid (HF) followed by aqueous ammonium fluoride (NH4F) has shown a statistically significant improvement of T1 by 22%, and reduction in the number of strongly-coupled TLS [3]. These examples, as well as many other published and ongoing investigations, demonstrate the mutual benefits that come from Rigetti's involvement in the SQMS collaboration. [1] - Pappas, D.P., et al. (2024). https://doi.org/10.1038/s43246-024-00596-z [2] - Bal, M., et al. (2024). https://doi.org/10.1038/s41534-024-00840-x [3] Kopas, C. J. et al. Preprint at https://doi.org/10.48550/arXiv.2408.02863 (2024).

Lachman, Ella↗