Search NASA⌕ Search

SEARCH · Search NASA

Results for “inlets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Low-speed aerodynamic performance of 50.8-centimeter-diameter noise-suppressing inlets for the Quiet, Clean, Short-haul Experimental Engine (QCSEE)

Two basic inlet concepts, a high throat Mach number (0.79) design and a low throat Mach number (0.60) design, were tested with four diffuser acoustical treatment designs that had face sheet porosity ranging from 0 to 24 percent for the high Mach number inlet and 0 to 28 percent for the low Mach number inlet. The tests were conducted in a low speed wind tunnel at free stream velocities of 0, 41, and 62 m/sec and angles of attack to 50 deg. Inlet throat Mach number was varied about the design value. Increasing the inlet diffuser face sheet porosity resulted in an increase in total pressure loss in the boundary layer for both the high and low Mach number inlet designs, however, the overall effect on inlet total pressure recovery of 0.991 at the design throat Mach number, a free stream velocity of 41 m/sec, and an angle of attack of 50 deg; Inlet flow separation at an angle of attack of 50 deg was encountered with only one inlet configuration the high Mach number design with the highest diffuser face sheet porosity (24 percent).

Abbott, J. M.↗

Top-mounted inlet system feasibility for transonic-supersonic fighter aircraft

The more salient findings are presented of recent top inlet performance evaluations aimed at assessing the feasibility of top-mounted inlet systems for transonic-supersonic fighter aircraft applications. Top inlet flow field and engine-inlet performance test data show the influence of key aircraft configuration variables-inlet longitudinal position, wing leading-edge extension planform area, canopy-dorsal integration, and variable incidence canards-on top inlet performance over the Mach range of 0.6 to 2.0. Top inlet performance data are compared with those or more conventional inlet/airframe integrations in an effort to assess the viability of top-mounted inlet systems relative to conventional inlet installations.

Williams, T. L.↗

An investigation of engine influence on inlet performance

The performance of a conventional engine/inlet installation, in which inlet and engine flow field interaction occurs, was compared to the performance of the same inlet remote coupled to the engine. The remote coupled inlet configuration decouples the influence of the engine on the inlet flow field and simulates current small scale inlet test techniques in which inlet airflow is provided by a vacuum source or coupled engine. The investigation was conducted in the NASA-Ames 40- by 80-foot wind tunnel using a General Electric TF-34 turbofan engine and a subsonic inlet having an average inlet contraction ratio of 1.26. Test results indicated that engine interaction allows the inlet to operate with lower distortion levels at and beyond the separation angle-of-attack experienced without engine interaction.

Hodder, B. K.↗

Experimental and analytical evaluation of the effects of simulated engine inlets on the blade vibratory stresses of the SR-3 model prop-fan

A cooperative wind tunnel test program, referred to as GUN-3, had been conducted previously to assess the effect of inlet configuration and location on the inlet face pressure recovery and inlet drag in the presence of a high-speed advanced turboprop. These tests were conducted with the inlets located just downstream of the SR-3 model Prop-Fan, a moderately swept, eight-bladed 62.2 cm (24.5 inch) diameter advanced, high-speed turboprop model fabricated from titanium. During these tests, two blades of the SR-3 model Prop-Fan were strain gaged to measure the vibratory blade stresses occurring during the inlet aerodynamic test program. The purpose of the effort reported herein was to reduce and analyze the test results related to the vibratory strain gage measurements obtained. Three inlet configurations had been tested. These were: (1) single scoop, (2) twin scoop, and (3) annular. Each of the three inlets was tested at a position just behind the rotor. The single scoop inlet was also tested at a position further aft. Tests were also done without an inlet. These results emphasize the importance of avoiding critical speeds in the continuous operating range.

Bansal, Prem N.↗

Theoretical evaluation of engine auxiliary inlet design for supersonic V/STOL aircraft

A higher order panel method is used to evaluate the potential flow of a 2-D supersonic V/STOL inlet. A nonsymmetric analytical inlet model is developed to closely match a wind tunnel model tested at NASA-Lewis. The analytical inlet used is analyzed for flow characteristics around the lower cowl lip and auxiliary inlets. The results for this analysis are obtained for the output of a computer program produced by the McDonnell Douglas Corp. This program is based on the Hess Panel Method which determines source strengths of panel distributed over a 3-D body. The analytical model was designed for the implementation of a drooped/translated cowl lip and auxiliary inlets as flow improvement concepts. A 40 or 70 deg droop lip can be incorporated on the inlet to determine if these geometry changes result in flow improvements which may reduce the propensity for flow separation on the interior portion of the lip. Auxiliary inlets are used to decrease the mass flow over the inlet lip; thus, the peak flow velocity is reduced at the lip which also lessens the likelihood of flow separation on the interior portion of the lip. A 2, 4, and 6 in. translated lip can be used to also decrease mass flow over the inlet lower lip in the same manner.

Boles, Michael A.↗

Evaluation of panel code predictions with experimental results of inlet performance for a 17-inch ducted prop/fab simulator operating at Mach 0.2

An axisymmetric panel code was used to evaluate a series of ducted propeller inlets. The inlets were tested in the Lewis 9 by 15 Foot Low Speed Wind Tunnel. Three basic inlets having ratios of shroud length to propeller diameter of 0.2, 0.4, and 0.5 were tested with the Pratt and Whitney ducted prop/fan simulator. A fourth hybrid inlet consisting of the shroud from the shortest basic inlet coupled with the spinner from the largest basic inlet was also tested. This later configuration represented the shortest overall inlet. The simulator duct diameter at the propeller face was 17.25 inches. The short and long spinners provided hub-to-tip ratios of 0.44 at the propeller face. The four inlets were tested at a nominal free stream Mach number of 0.2 and at angles of attack from 0 degrees to 35 degrees. The panel code method incorporated a simple two-part separation model which yielded conservative estimates of inlet separation.

Boldman, D. R.↗

Evaluation of panel code predictions with experimental results of inlet performance for a 17-inch ducted prop/fan simulator operating at Mach 0.2

An axisymmetric panel code was used to evaluate a series of ducted propeller inlets. The inlets were tested in the Lewis 9 by 15 Foot Low Speed Wind Tunnel. Three basic inlets having ratios of shroud length to propeller diameter of 0.2, 0.4, and 0.5 were tested with the Pratt and Whitney ducted prop/fan simulator. A fourth hybrid inlet consisting of the shroud from the shortest basic inlet coupled with the spinner from the largest basic inlet was also tested. This later configuration represented the shortest overall inlet. The simulator duct diameter at the propeller face was 17.25 inches. The short and long spinners provided hub-to-tip retios of 0.44 at the propeller face. The four inlets were tested at a nominal free stream Mach number of 0.2 and at angles of attack from 0 degrees to 35 degrees. The panel code method incorporated a simple two-part separation model which yielded conservative estimates of inlet separation.

Boldman, D. R.↗

Evaluation and application of the Baldwin-Lomax turbulence model in two-dimensional, unsteady, compressible boundary layers with and without separation in engine inlets

There is a practical need to model high speed flows that exist in jet engine inlets. The boundary layers that form in these inlets may be turbulent or laminar and either separated or attached. Also, unsteady supersonic inlets may be subject to frequent changes in operating conditions. Some changes in the operating conditions of the inlets may include varying the inlet geometry, bleeds and bypasses, and rotating or translating the centerbody. In addition, the inlet may be either started or unstarted. Therefore, a CFD code, used to model these inlets, may have to run for several different cases. Also, since the flow conditions through an unsteady inlet may be continually fluctuating, the CFD code which models these flows may have to be run over many time steps. Therefore, it would be beneficial that the code run quickly. Many turbulence models, however, are cumbersome to implement and require a lot of computer time to run, since they add to the number of differential equations to be solved to model a flow. The Baldwin-Lomax turbulence model is a popular model. It is an algebraic, eddy viscosity model. The Baldwin-Lomax model is used in many CFD codes because it is quick and easy to implement. In this paper, we will discuss implementing the Baldwin-Lomax turbulence model for both steady and unsteady compressible flows. In addition, these flows may be either separated or attached. In order to apply this turbulence model to flows which may be subjected to these conditions, certain modifications should be made to the original Baldwin-Lomax model. We will discuss these modifications and determine whether the Baldwin-Lomax model is a viable turbulence model that produces reasonably accurate results for high speed flows that can be found in engine inlets.

Sakowski, Barbara↗

Investigation of an underslung half-cone inlet with compression surface mounted outboard from fuselage at Mach numbers of 1.5, 1.8, and 2.0

An investigation was conducted to determine the performance of an underslung half-cone inlet mounted on a missile forebody model with the compression surface outboard from the fuselage. The inlet was designed for shock-on-lip operation at Mach number 2.0 with 25 degree half-angle spike. The cowling was attached to the fuselage through the boundary-layer plow and served as part of the fuselage boundary-layer diverter system. The performance of the half-cone inlet was compared with that of a scoop-type inlet and a normal-wedge inlet on a maximum-thrust-minus-drag basis. The increase in pressure recovery obtained with the half-cone inlet over that obtained with the reference inlets offset the slightly higher drags observed over the Mach number range for the half-cone so that the performance of this configuration was equal to that of the other inlets at Mach number 2.0 and was slightly superior at the lower Mach numbers. For a particular configuration, a peak pressure recovery of 0.879 was obtained at Mach number 2.0, zero angle of attack, and 4-percent throat bleed; the subcritical stability was 16 percent. Use of a fuselage-mounted boundary-layer splitter plate ahead of the inlet did not improve the stability. Subcritical distortion values were below 10 percent for all configurations. (author)

Yeager, Richard A↗

Axisymmetric inlet minimum weight design method

An analytical method for determining the minimum weight design of an axisymmetric supersonic inlet has been developed. The goal of this method development project was to improve the ability to predict the weight of high-speed inlets in conceptual and preliminary design. The initial model was developed using information that was available from inlet conceptual design tools (e.g., the inlet internal and external geometries and pressure distributions). Stiffened shell construction was assumed. Mass properties were computed by analyzing a parametric cubic curve representation of the inlet geometry. Design loads and stresses were developed at analysis stations along the length of the inlet. The equivalent minimum structural thicknesses for both shell and frame structures required to support the maximum loads produced by various load conditions were then determined. Preliminary results indicated that inlet hammershock pressures produced the critical design load condition for a significant portion of the inlet. By improving the accuracy of inlet weight predictions, the method will improve the fidelity of propulsion and vehicle design studies and increase the accuracy of weight versus cost studies.

Nadell, Shari-Beth↗

A Wind Tunnel Investigation of Three NACA 1-Series Inlets at Mach Numbers up to 0.92

Pressure distributions on three NACA 1-series inlets have been obtained in the Langley 16-Foot Transonic Tunnel. The cowl diameter ratio (ratio of cowl highlight diameter to cowl maximum diameter) was 0.85 for all three inlets. The cowl length ratio (ratio of cowl length to cowl maximum diameter) was 1.0 for two of the inlets (NACA 1-85-100) and 0.439 for the other (NACA 1-85-43.9) inlet. One of the inlets with a cowl length ratio of 1.0 had an internal contraction ratio (ratio of highlight area to throat area) of 1.009 and the other had a contraction ratio of 1.250. The inlet with a cowl length ratio of 0.439 also had an internal contraction ratio of 1.250. All three inlets had longitudinal rows of static pressure orifices on the top and bottom external cowl surfaces. The inlet with a contraction ratio of 1.009 also had a row of static pressure orifices on the side of the cowl (external surface). The two inlets with a contraction ratio of 1.250 had a longitudinal row of static pressure orifices on the diffuser surface.

Re, Richard J.↗

Inlet Shape Effects on the Far-Field Sound of a Model Fan

A wind tunnel test was conducted to determine the effects of inlet shape on fan radiated noise. Four inlet geometries, which included a long standard flight type inlet, a short, aggressive flight inlet a scarf inlet, and an elliptical inlet were investigated in the study. The fan model used in the study was a 0.1 scale of the Pratt and Whitney Advanced Ducted Propeller (ADP), an ultra high bypass ratio turbofan engine. Acoustic data are presented for a fan speed of 70% (12,000 rpm) and a tunnel speed of 0.10 Mach number, The fan was configured with a 16-bladed rotor and a 40 stator vane set that were separated by 2.0 chord lengths. The radiated noise was measured with 15 microphones on a boom that traversed the length of the tunnel test section. Data from these microphones are presented in the form of sideline angle directivity plots. Noise associated with the test inlets was also predicted using a ray acoustics code. Inlet shape has been found to have a significant effect on both tone and broadband noise, and the non-axisymmetric inlet shape can be used for a noise reduction method.

Clark, L. R.↗

Inlet-Compressor Analysis Using Coupled CFD Codes

Propulsion performance and operability are key factors in the development of a successful aircraft. For high-speed supersonic aircraft, mixed-compression inlets offer high performance but are susceptible to an instability referred to as unstart. An unstart occurs when a disturbance originating in the atmosphere or the engine causes the shock system to be expelled from the inlet. This event can have adverse effects on control of the aircraft, which is unacceptable for a passenger plane such as the high speed civil transport (HSCT). The ability to predict the transient response of such inlets to flow perturbations is, therefore, important to the proper design of the inlet and the control measures used to prevent unstart. Computational fluid dynamics (CFD) is having an increasing role in the analysis of individual propulsion components. isolated inlet studies are relatively easy to perform, but a major uncertainty is the boundary condition used at the inlet exit to represent the engine - the so-called compressor face boundary condition. A one-dimensional (I-D) Euler inlet simulation (ref. 1) showed that the predicted inlet unstart tolerance to free-stream pressure perturbations can vary by as much as a factor of about six, depending on the boundary condition used. Obviously, a thorough understanding of dynamic interactions between inlets and compressors/fans is required to provide the proper boundary condition.

Cole, Gary↗

Investigation of Methods for the Structural Weight Analysis of a Mach 2.4 Axisymmetric Inlet

Structural design and analysis tools appropriate for estimating the structural weight of an axisymmetric inlet designed for Mach 2.4 cruise were evaluated. Little information regarding the inlet mechanical design is available in the preliminary design phase, so it is necessary to first develop a reasonable structural design before estimating the inlet weight. The Internally Pressurized Structure Synthesis and Optimization (IPSSO) program, employing an analytical approach, was chosen for evaluation due to its combined design and analysis capabilities. The inlet design produced by IPSSO was then analyzed using the NASTRAN finite element program. The finite element analysis was performed to help identify the limitations of the analytically based code as well as to evaluate NASTRAN for this application. Comparison between the IPSSO inlet weight and that of a similar inlet developed by the Boeing Commercial Airplane Group was also made. Program evaluation concluded that the combined use of IPSSO to create an initial design and NASTRAN to perform a numerical analysis would provide the capability to evaluate a limited number of inlet design The development of a new tool for the minimum weight design and analysis of inlet structures would be required for greater flexibility in evaluating inlet conceptual designs.

Nadell, Shari-Beth↗

Hypersonic Combustor Model Inlet CFD Simulations and Experimental Comparisons

Numerous two-and three-dimensional computational simulations were performed for the inlet associated with the combustor model for the hypersonic propulsion experiment in the NASA Ames 16-Inch Shock Tunnel. The inlet was designed to produce a combustor-inlet flow that is nearly two-dimensional and of sufficient mass flow rate for large scale combustor testing. The three-dimensional simulations demonstrated that the inlet design met all the design objectives and that the inlet produced a very nearly two-dimensional combustor inflow profile. Numerous two-dimensional simulations were performed with various levels of approximations such as in the choice of chemical and physical models, as well as numerical approximations. Parametric studies were conducted to better understand and to characterize the inlet flow. Results from the two-and three-dimensional simulations were used to predict the mass flux entering the combustor and a mass flux correlation as a function of facility stagnation pressure was developed. Surface heat flux and pressure measurements were compared with the computed results and good agreement was found. The computational simulations helped determine the inlet low characteristics in the high enthalpy environment, the important parameters that affect the combustor-inlet flow, and the sensitivity of the inlet flow to various modeling assumptions.

Venkatapathy, E.↗

Effect of Inlet Air Distortion on the Steady-State and Surge Characteristics of an Axial-Flow Turbojet Compressor

An investigation was conducted in an altitude test chamber to determine the effects of inlet airflow distortion on the compressor steady-state and surge characteristics of a high-pressure ratio, axial-flow turbojet engine. Circumferential-type inlet flow distortions were investigated, which covered a range of distortion sector angles from 20 deg to 168 deg and distortion levels up to 22 percent. The presence of inlet airflow distortions at the compressor face resulted in a substantial increase in the local pressure ratio in the distorted region, primarily for the inlet stages. The local pressure ratio in the distorted region for the inlet stages increased as either the distortion sector angle decreased or the percent distortion increased. The average compressor-surge pressure ratio was much more sensitive to inlet airflow distortions at lower engine speeds than at engine speeds near rated. Hence, compressor-surge margin reduction due to inlet airflow distortion was quite severe at the lower engine speeds. Although the average compressor-surge pressure ratio was generally reduced with inlet flow distortion, local pressure ratios across the distorted sector of the compressor were obtained during surge and were significantly greater than the normal compressor-surge pressure ratio. This was a result of increased loading of the inlet stages in the distorted region.

Ciepluch, Carl C.↗

Boundary-Layer-Ingesting Inlet Flow Control

This paper gives an overview of a research study conducted in support of the small-scale demonstration of an active flow control system for a boundary-layer-ingesting (BLI) inlet. The effectiveness of active flow control in reducing engine inlet circumferential distortion was assessed using a 2.5% scale model of a 35% boundary-layer-ingesting flush-mounted, offset, diffusing inlet. This experiment was conducted in the NASA Langley 0.3-meter Transonic Cryogenic Tunnel at flight Mach numbers with a model inlet specifically designed for this type of testing. High mass flow actuators controlled the flow through distributed control jets providing the active flow control. A vortex generator point design configuration was also tested for comparison purposes and to provide a means to examine a hybrid vortex generator and control jets configuration. Measurements were made of the onset boundary layer, the duct surface static pressures, and the mass flow through the duct and the actuators. The distortion and pressure recovery were determined by 40 total pressure measurements on 8 rake arms each separated by 45 degrees and were located at the aerodynamic interface plane. The test matrix was limited to a maximum free-stream Mach number of 0.85 with scaled mass flows through the inlet for that condition. The data show that the flow control jets alone can reduce circumferential distortion (DPCPavg) from 0.055 to about 0.015 using about 2.5% of inlet mass flow. The vortex generators also reduced the circumferential distortion from 0.055 to 0.010 near the inlet mass flow design point. Lower inlet mass flow settings with the vortex generator configuration produced higher distortion levels that were reduced to acceptable levels using a hybrid vortex generator/control jets configuration that required less than 1% of the inlet mass flow.

Owens, Lewis R.↗

High Reynolds Number Investigation of a Flush Mounted, S-Duct Inlet With Large Amounts of Boundary Layer Ingestion

An experimental investigation of a flush-mounted, S-duct inlet with large amounts of boundary layer ingestion has been conducted at Reynolds numbers up to full scale. The study was conducted in the NASA Langley Research Center 0.3-Meter Transonic Cryogenic Tunnel. In addition, a supplemental computational study on one of the inlet configurations was conducted using the Navier-Stokes flow solver, OVERFLOW. Tests were conducted at Mach numbers from 0.25 to 0.83, Reynolds numbers (based on aerodynamic interface plane diameter) from 5.1 million to 13.9 million (full-scale value), and inlet mass-flow ratios from 0.29 to 1.22, depending on Mach number. Results of the study indicated that increasing Mach number, increasing boundary layer thickness (relative to inlet height) or ingesting a boundary layer with a distorted profile decreased inlet performance. At Mach numbers above 0.4, increasing inlet airflow increased inlet pressure recovery but also increased distortion. Finally, inlet distortion was found to be relatively insensitive to Reynolds number, but pressure recovery increased slightly with increasing Reynolds number.This CD-ROM supplement contains inlet data including: Boundary layer data, Duct static pressure data, performance-AIP (fan face) data, Photos, Tunnel wall P-PTO data and definitions.

Berrier, Bobby L.↗