Search NASA⌕ Search

SEARCH · Search NASA

Results for “laser heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Silicon ribbon growth using scanned lasers

The recent demand for low-cost photovoltaic arrays has renewed the interest in growing silicon in ribbon form. The approach used in the present paper for the growth of low-cost silicon ribbon is shown schematically. A pair of scanned, focused CO2 laser beams is directed onto both sides of a preformed silicon ribbon. A narrow (about 1 mm high) molten zone is formed across the full width of the ribbon. As the silicon ribbon is passed through the laser-heated zone, large grains are produced in the recrystallized ribbon. The laser beam path is outlined schematically. As a general rule, the lenses are not positioned so as to bring the laser beams to a fine focus, since highly focused beams would vaporize the silicon surface rather than serve to melt the bulk. Silicon ribbon has been grown at rates up to 13.3 cm/min by this approach. The best solar cell fabricated so far on this material has a conversion efficiency of 12.7%.

Baghdadi, A.↗

Failure Mechanisms and Life Prediction of Thermal and Environmental Barrier Coatings under Thermal Gradients

Ceramic thermal and environmental barrier coatings (TEBCs) will play an increasingly important role in gas turbine engines because of their ability to further raise engine temperatures. However, the issue of coating durability is of major concern under high-heat-flux conditions. In particular, the accelerated coating delamination crack growth under the engine high heat-flux conditions is not well understood. In this paper, a laser heat flux technique is used to investigate the coating delamination crack propagation under realistic temperature-stress gradients and thermal cyclic conditions. The coating delamination mechanisms are investigated under various thermal loading conditions, and are correlated with coating dynamic fatigue, sintering and interfacial adhesion test results. A coating life prediction framework may be realized by examining the crack initiation and propagation driving forces for coating failure under high-heat-flux test conditions.

Zju, Dongming↗

Innovative laser-based methods for monitoring fuel retention in ITER

This paper addresses the challenge of tritium inventory management in ITER and future fusion reactors, highlighting the importance of accurate tritium measurement and its spatial distribution within the vacuum vessel. Given ITER’s operational constraints, especially the limit on tritium retention, precise measurement is essential for both safety and regulatory compliance. To tackle these questions, the paper presents the T-monitor diagnostic system developed by Forschungszentrum Jülich, which uses Laser-Induced Desorption (LID) in combination with Diagnostic Residual Gas Analysis (DRGA) to measure hydrogen isotope concentrations on the surface of divertor tiles. The system integrates a high-power laser, advanced optical components, and a Fast Scanning Mirror Unit (FSMU) for accurate laser spot positioning with rapid response. Designed to measure in situ tritium retention, the diagnostic provides high-resolution spatial mapping, vital for evaluating detritiation strategies. The laser heating process increases the divertor surface temperature to 1600 K within the laser spot, promoting hydrogen isotope desorption. Accurate measurements require the precise control of laser parameters, including pulse duration and spot size, with a target relative accuracy of 20%. The optical design includes both in-vessel and ex-vessel components, such as durable high-reflectivity mirrors made of gold and copper, selected not only for their infrared performance but also for their transmission of visible wavelengths for observation purposes. To protect optical components from contamination, a pneumatic shutter is used.

Hydrogen isotopes↗

Laser intensity scaling of the magnetic field from a laser-driven coil target

In this paper, we report on the first direct voltage and current measurements from a laser-generated magnetic field coil target. The magnetic field was observed to scale with the laser intensity as $B ∝ \mathcal{I}^{0.66±0.13}_\text{laser}$. This scaling relation can be derived from the measured voltage approximated by the laser-heated plasma electron temperature $T_e$. The experiments used a 1053 nm laser with pulse lengths ranging from 0.5 to 20 ns and intensities ranging from 10 9 to 10 14 W/cm 2 to generate an electric potential that drives current through the coil. We show that the behavior of the coil can be described with a lumped-element circuit model.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

On the control of electron heating for optimal laser radiation pressure ion acceleration

We study the onset of electron heating in intense laser–solid interactions and its impact on the spectral quality of radiation pressure accelerated ions in both hole boring and light sail regimes. Two- and three-dimensional particle-in-cell (PIC) simulations are performed over a wide range of laser and target parameters and reveal how the pulse duration, profile, polarization and target surface stability control the electron heating, the dominant ion acceleration mechanisms and the ion spectra. We find that the onset of strong electron heating is associated with the growth of the Rayleigh–Taylor-like instability at the front surface and must be controlled to produce high-quality ion beams, even when circularly polarized lasers are employed. We define a threshold condition for the maximum duration of the laser pulse that allows mitigation of electron heating and radiation pressure acceleration of narrow energy spread ion beams. The model is validated by three-dimensional PIC simulations, and the few experimental studies that reported low energy spread radiation pressure accelerated ion beams appear to meet the derived criteria. The understanding provided by our work will be important in guiding future experimental developments, for example for the ultrashort laser pulses becoming available at state-of-the-art laser facilities, for which we predict that proton beams with $\sim$ 150–250 MeV, $\sim$ 30% energy spread, and a total laser-to-proton conversion efficiency of $\sim$ 20% can be produced.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation and Control of Unidirectional Ballistic Dynamics of Nanoparticles at a Liquid–Gas Interface by 4D Electron Microscopy

Understanding and controlling the dynamics of active Brownian objects far from equilibrium are fundamentally important for emerging technologies such as artificial micro/nanomotors for drug deliveries and noninvasive microsurgery. However, direct observation and control of unidirectional propulsion of individual nanoscale objects are technically challenging due to the required spatiotemporal resolution. Here, we report in situ visualization and manipulation of unidirectional superfast ballistic dynamics of a single-photon-activated gold nanoparticle (NP) along the liquid–gas interface by four-dimensional electron microscopy (4D EM) at nanometer and nanosecond scales. We observed that, upon repetitive femtosecond laser excitation, the NP at the liquid–gas interface exhibits a continuously superfast unidirectional translation with a linear dependence of its root mean squared velocity (νrms) on either the laser fluence or repetition rate. Under a single femtosecond pulse excitation, the NP exhibits a superfast ballistic translation at the nanosecond time scale. Combined experiment and physical modeling reveals that the superfast unidirectional, ballistic translation is driven by unidirectional random impulsive forces arising from the nanobubbles (NBs) induced by enhanced laser heating as a result of plasmonic excitation, which is controllable by tuning the laser characteristics. Furthermore, this directional plasmonic NB-propulsion mechanism sheds light on the design of light-controllable artificially intelligent micro/nanomotor systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Reversible structural transformations in supercooled liquid water from 135 to 245 K

Water has many anomalous properties compared to “simple” liquids, and these anomalies are typically enhanced in supercooled water.1-3 While numerous models have been proposed, including the liquid-liquid critical point,4,5 the singularity-free scenario,6 and the stability limit conjecture,1 a molecular-level understanding remains elusive. The main difficulty in determining which, if any, of these models is correct is the limited amount of data in the relevant temperature and pressure ranges. For water at ambient pressures, which is the focus of this work, data is largely missing from 160 – 232 K (“No Man’s Land”) due to rapid crystallization.2,3 Whether rapid crystallization is just an experimental obstacle, or a fundamental problem signaling the inability of water to thermally equilibrate prior to crystallization is also a major unanswered question.5,7 Here, we investigate the structural transformations of transiently-heated, supercooled water with nanosecond time resolution using infrared vibrational spectroscopy. The experiments demonstrate three key results. First, water’s structure relaxes from its initial configuration to a “steady-state” configuration prior to the onset of crystallization over a wide temperature range. Second, water’s steady-state structure can be reproduced by a linear combination of two, temperature-independent structures that correspond to a “high-temperature liquid” and a “low-temperature liquid.” Third, the observed structural changes are reversible over the full temperature range. Taken together, these results show that supercooled water can equilibrate prior to crystallization for temperatures from the homogeneous nucleation temperature, TH ~232 K,3 down to the glass transition temperature (Tg ~ 136 K). Second, the results provide support for the hypothesis that supercooled water can be described as a mixture of two, structurally-distinct, interconvertible liquids from 135 K to 245 K.5,8-18

Kringle, Loni M.↗

Thermal Fatigue and Fracture Behavior of Ceramic Thermal Barrier Coatings

Thermal fatigue and fracture behavior of plasma-sprayed ceramic thermal barrier coatings has been investigated under high heat flux and thermal cyclic conditions. The coating crack propagation is studied under laser heat flux cyclic thermal loading, and is correlated with dynamic fatigue and strength test results. The coating stress response and inelasticity, fatigue and creep interactions, and interface damage mechanisms during dynamic thermal fatigue processes are emphasized.

Zhu, Dong-Ming↗

Seeded gas thrusters and related system components

A program involved with the construction and test of a number of laser heated thrusters is described. These thrusters, with a cavity approximately 23 cm long and 3.5 cm in i.d., are to be tested by NASA at a later date with a laser beam focused through the throat to heat hydrogen propellant containing an opacifier. The heated propellant exhausts through a supersonic nozzle with a 0.6 cm throat at 3000 C. Thrust stands and control systems were furnished with the thrusters. The report describes radio frequency plasma heated hot and cold flow simulation tests by the contractor.

Poole, J. W.↗

NASA's laser-propulsion project

Design concepts, study results, and research directions toward development of CW laser heating of remotely flying spacecraft fuels to provide high impulse thrust are presented. The incident laser radiation would be absorbed by hydrogen through a medium of a laser-supported plasma. The laser energy could be furnished from an orbiting solar-powered laser platform and used to drive the engines of an orbital transfer vehicle (OTV) at costs less than with a chemical propulsion system. The OTV propulsion chamber would be reduced in size comparable to the volume addition of the incident laser energy absorber. The temperatures in the hydrogen-fueled system could reach 5000-15,000 K, and studies have been done to examine the feasibility of ion-electron recombination. Kinetic performance, temperature field, and power necessary to sustain a laser thrust augmented system modeling results are discussed, along with near-term 30 kW CO2 laser system tests.

Jones, L. W.↗

Thermal Conductivity and Elastic Modulus Evolution of Thermal Barrier Coatings under High Heat Flux Conditions

Laser high heat flux test approaches have been established to obtain critical properties of ceramic thermal barrier coatings (TBCs) under near-realistic temperature and thermal gradients that may he encountered in advanced engine systems. Thermal conductivity change kinetics of a thin ceramic coating were continuously monitored in real time at various test temperatures. A significant thermal conductivity increase was observed during the laser simulated engine heat flux tests. For a 0.25 mm thick ZrO2-8%Y2O3 coating system, the overall thermal conductivity increased from the initial value of 1.0 W/m-K to 1. 15 W/m-K, 1. 19 W/m-K and 1.5 W/m-K after 30 hour testing at surface temperatures of 990C, 1100C, and 1320C. respectively. Hardness and modulus gradients across a 1.5 mm thick TBC system were also determined as a function of laser testing time using the laser sintering/creep and micro-indentation techniques. The coating Knoop hardness values increased from the initial hardness value of 4 GPa to 5 GPa near the ceramic/bond coat interface, and to 7.5 GPa at the ceramic coating surface after 120 hour testing. The ceramic surface modulus increased from an initial value of about 70 GPa to a final value of 125 GPa. The increase in thermal conductivity and the evolution of significant hardness and modulus gradients in the TBC systems are attributed to sintering-induced micro-porosity gradients under the laser-imposed high thermal gradient conditions. The test techniques provide a viable means for obtaining coating data for use in design, development, stress modeling, and life prediction for various thermal barrier coating applications.

Zhu, Dongming↗

Compact pulsed laser having improved heat conductance

A highly efficient, compact pulsed laser having high energy to weight and volume ratios is provided. The laser utilizes a cavity reflector that operates as a heat sink and is essentially characterized by having a high heat conductivity, by being a good electrical insulator and by being substantially immune to the deleterious effects of ultra-violet radiation. Manual portability is accomplished by eliminating entirely any need for a conventional circulating fluid cooling system.

Yang, L. C.↗

Compact laser through improved heat conductance

A 16-joule-pulse laser has been developed in which a boron nitride heat-conductor enclosure is used to remove heat from the elements. Enclosure is smaller and lighter than systems in which cooling fluids are used.

Yang, L. C.↗

Visualization of Thermal and Strain Dynamics in X-ray Optics by Time-Resolved Rocking Curve Imaging

The absorption of intense X-ray pulses from free-electron lasers by X-ray crystal optics triggers rapid thermal and mechanical responses, including lattice compression, expan- sion, and strain-wave propagation, which dynamically modify diffraction conditions and wavefront properties. These effects pose significant challenges for next-generation high- repetition-rate X-ray sources, particularly for crystal monochromators used in XFEL beam- lines and self-seeding. Here, we demonstrate time-resolved rocking curve imaging (TrRCI) of X-ray Bragg optics with high spatial resolution (6.4 μm) and sub-1-μrad angular resolu- tion, enabling direct visualization of lattice dynamics from nanoseconds to microseconds. By combining a high-flux beamline at SPring-8, a scintillator-coupled sCMOS detector, and a synchronized femtosecond laser system, we capture lattice dynamics induced by tran- sient laser heating with a strain sensitivity on the order of 10−6 . Our results reveal transient lattice deformation and the propagation of laser-induced strain waves over millimeter-scale distances. This approach provides experimental benchmarks for understanding heat-load effects in high-repetition-rate X-ray optics.

Source record↗

Oscillatory/chaotic thermocapillary flow induced by radiant heating

The objective of this paper is to conduct ground-based experiments to measure the onset conditions of oscillatory Marangoni flow in laser-heated silicone oil in a cylindrical container. For a single fluid, experimental data are presented using the aspect ratio and the dynamic Bond number. It is found that for a fixed aspect ratio, there seems to be an asymptotic limit of the dynamic Bond number beyond which no onset of flow oscillation could occur. Experimental results also suggested that there could be a lower limit of the aspect ratio below which there is no onset of oscillatory flow.

Hsieh, Kwang-Chung↗

Characterizing major and trace element compositions in fallout melt glass from a near-surface nuclear test

We report the chemical and isotopic compositions of fallout melt glasses from nuclear tests contain a range of information constraining the physical conditions within the fireball and the mechanisms of fallout formation but historic studies tended to exclude the behavior of stable major and trace elements. Here, we present a large study specifically focused on major and trace element relationships within a population of macroscale fallout samples from a single event. We interpret these data to better constrain how fallout melt glass formation in near surface environments is influenced by that environment and demonstrate how major and trace element abundances can provide useful insights into chemical processes within the fireball. Data confirm that the uranium in the fallout glass population derives from two isotopically distinct endmembers: isotopically enriched uranium (presumably from the weapon), and natural composition uranium that may be a combination of anthropogenic and environmental materials from within the blast zone. The similarity between major and trace element concentrations in fallout and corresponding local soils from the event site confirm the local soils as the most probable source of entrained material into the fireball and the source of carrier material into which the bomb vapor was incorporated. The lack of correlation between major and trace element abundances with size indicates that volatility driven processes, such as condensation from the fireball, do not control the composition of macroscale fallout melt glass. Although the fallout has major and trace element chemical characteristics broadly similar to those of the local, associated soils, some systematic differences are observed between the two populations. Fallout melt glass is depleted in volatile elements such as K, Na, Tl and Pb, consistent with heating to temperatures above ~1000 °C for 3-10 s. This is supported by the results of laser heating experiments performed on rhyolitic soil at temperatures (1600-2200 °C) and timescales (1-120 s) that are broadly relevant to fallout formation conditions. Relative enrichments of metals such as Cu and Co do not correlate with the abundance of uranium, suggesting that fallout also records input of near field anthropogenic materials. Our observations suggest that major chemical features can be related to processing in the fireball and used to inform the thermal-chemical evolution of the system. Ultimately, these data are consistent with a fallout formation mechanism that involves rapid melting of surface materials to form carrier material melts with minor incorporation of bomb vapor and a degree of volumetric volatile loss due to heating.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Strong interplay between superluminosity and radiation friction during direct laser acceleration

Using a test-particle model, we examine direct laser acceleration of electrons within a magnetic filament that has been shown to form inside a laser-irradiated plasma. We focus on ultra-high intensity interactions where the force of radiation friction caused by electron emission of electromagnetic radiation must be taken into account. It is shown that even relatively weak superluminosity of laser wave fronts—the feature that has been previously neglected—qualitatively changes the electron dynamics, leading to a so-called attractor effect. As a result of this effect, electrons with various initial energies reach roughly the same maximum energy and emit roughly the same power in the form of x-rays and gamma-rays. Our analysis implies that the primary cause of the superluminosity is the laser-heated plasma. The discovered strong interplay between superluminosity and radiation friction is of direct relevance to laser-plasma interactions at high-intensity multi-PW laser facilities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evidence for phonon hardening in laser-excited gold using x-ray diffraction at a hard x-ray free electron laser

Studies of laser-heated materials on femtosecond timescales have shown that the interatomic potential can be perturbed at sufficiently high laser intensities. For gold, it has been postulated to undergo a strong stiffening leading to an increase of the phonon energies, known as phonon hardening. Despite efforts to investigate this behavior, only measurements at low absorbed energy density have been performed, for which the interpretation of the experimental data remains ambiguous. By using in situ single-shot x-ray diffraction at a hard x-ray free-electron laser, the evolution of diffraction line intensities of laser-excited Au to a higher energy density provides evidence for phonon hardening.

36 MATERIALS SCIENCE↗