Search NASA⌕ Search

SEARCH · Search NASA

Results for “liquid additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Transition from Vogel-Fulcher-Tammann to Arrhenius Ion-Conducting Behavior in Poly(Ethyl Acrylate)-Based Solid Polymer Electrolytes via Succinonitrile Plasticizer Addition

Solid polymer electrolytes (SPEs) offer potential advantages over liquid electrolytes, including flexibility, safety, and processability. However, they suffer from low room-temperature ionic conductivity. Recently, it has been reported a poly(ethyl acrylate) based (polyEA) SPE, by incorporating 50 wt% of succinonitrile (SN) solid plasticizer, 30 wt% of lithium salt and 5 wt% of fluoroethylene carbonate additive, which achieves a high room-temperature ionic conductivity of 1.01 × 10 −3 S cm −1 (Nat. Nanotechnol, 2022, 17, 768-776). This novel SPE exhibits stability against Li 0 and anodic stability up to 4.9 V vs Li + /Li. However, the specific mechanism responsible for its high ionic conductivity remains elusive. In this work, by adjusting the weight ratio of SN in the SPE, a transition from Vogel-Fulcher-Tammann to Arrhenius ion-conducting behavior is observed. It is demonstrated that the addition of SN leads to the gradual decoupling of Li-ion from the polymer backbone and its coordination with SN, as revealed by 6 Li solid-state nuclear magnetic resonance spectroscopy. As a result, Li-ion migration primarily occurs through SN rather than the segmental motion of the polymer backbone. Performances of the SPE in Cu||Li, Li||Li and a LiFePO 4 ||Li pouch cells are shown to demonstrate the commercial viability of this SPE in Li 0 -anode solid-state batteries.

Electrochemistry↗
DOE OSTI2022

Additive manufacturing and testing of a ceramic heat exchanger for high-temperature and high-pressure applications for concentrating solar power

Heat exchangers with excellent corrosion and oxidation resistances are essential for the next-generation concentrating solar power (CSP) plants using a molten salt heat transfer fluid and a supercritical CO 2 Brayton power cycle that can operate at temperatures > 700 °C for higher efficiencies. Techniques were developed for additively manufacturing ceramic materials for applications involving high temperature, high pressure, and high corrosion resistance as needed for the CSP application. Based on a previous ceramic heat exchanger design with its cross-section geometry of the flow channels optimized for heat transfer and mechanical strength, lab-scale prototype heat exchangers, with integrated headers and incorporated flow channel dimensional compensations, were fabricated by using the binder jetting process. The printed prototype heat exchangers were successfully densified through the processes of liquid polymer infiltration and pyrolysis. In addition, thermophysical properties of the densified silicon carbide parts were measured to provide necessary design information. Experimental heat transfer testing of the lab-scale prototype heat exchanger was conducted, and the experimental data agreed reasonably well with the simulated results. Furthermore, this agreement provides validation of the simulation models for their applicability to the development of a full-scale ceramic heat exchanger.

14 SOLAR ENERGY↗
DOE OSTI2021

Predicting sintering window during supersolidus liquid phase sintering of steels using feedstock analysis and CALPHAD

Binder jet 3D printing results in carbon pickup from the binder at the inter-particle regions during binder burnout. The excess carbon lowers the solidus temperature of the green part locally during supersolidus liquid phase sintering (SLPS). Currently, thermodynamic calculations rely on the use of bulk powder compositions to predict the sintering window. This can overestimate the sintering temperature since the local increase in carbon on powder surfaces is not accounted for, that can locally lower the solidus temperature during SLPS. Here we show that using the inputs from feedstock and binder analysis, the excess carbon and hence the sintering window for the alloy can be predicted using CALPHAD. We present a case study on applying the proposed approach for pressureless sintering of binder jet additive manufactured (BJAM) of H13 steel via SLPS.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Towards cost-competitive middle distillate fuels from ethanol within a market-flexible C2 platform-based biorefinery concept

Ethanol to middle distillates (ETMD) is a promising pathway to produce sustainable liquid fuels to decarbonize the hard-to-electrify transportation sectors due to (1) the abundant sugar/starch and lignocellulosic biomass, (2) the existing deployment scale of fuel ethanol production (similar to 29 billion gallons per year globally), and (3) emerging opportunities in C2+ alcohol synthesis from CO2. Here we report a conceptual market-responsive biorefinery centered around a new ETMD pathway based on one-step ethanol to butene-rich olefins (ETO) over a Cu-Zn-Y/Beta catalyst. Specifically, this ethanol conversion pathway comprises one-step ETO, oligomerization, and hydrotreating. This ETO is distinct from that in the conventional ethanol-to-jet process which is based on two-step ethanol to ethylene and ethylene oligomerization to butenes. Butene-rich olefins can be shifted to butadiene-rich products by simply changing the reaction atmosphere from hydrogen to inert gas over the same ETO catalyst. Leveraging the experimental results, baseline techno-economic analysis (TEA) and sensitivity analysis indicate that the ethanol conversion cost is $0.60 per gallon gasoline equivalent (GGE), with opportunities for further cost reduction via improving the liquid hydrocarbon yield and space velocities, and process optimization on balancing dewatering of ethanol feed prior to the ETO step. The minimum fuel selling price (MFSP) of liquid hydrocarbons derived from corn starch ethanol with butadiene as coproduct is $1.64 per GGE, in the range that is cost competitive with petroleum kerosene-type jet fuel. Projected MFSP for cellulosic ethanol (corn stover) derived hydrocarbons is below $3.00 per GGE and co-production of butadiene further reduces the MFSP to $1.70 per GGE. The Well-to-Wake life-cycle analysis indicates that 85% greenhouse gas emission reduction can be achieved when using corn stover compared to petroleum reference and the associated carbon credits will provide significant economic incentives to favor the cellulosic ethanol-derived hydrocarbon fuels. This study demonstrates a low-cost pathway to middle distillate fuels leveraging existing ethanol infrastructure, where catalysis innovation drives the reduction of process complexity and flexible coproduction of a value-added chemical product.

Zhang, Junyan↗
DOE OSTI2022

Use Cases and Model Development of Thermal Storage Coupling for Advanced Nuclear Reactors

This report discusses the different options for coupling thermal energy storage (TES) systems to advanced nuclear power plants (A-NPPs) in order to enable flexible and hybrid plant operation. An advanced light-water reactor (ALWR) and a high-temperature gas-cooled reactor (HTGR) were selected as the initial use cases for demonstrating a thermally balanced energy storage coupling design for thermal power extraction. Cost functions for the A-LWR were derived from the fully balanced models that were developed based on three different coupling options with three different thermal energy bypass ratios. For the next steps, cost functions for the HTGR will also be derived, and additional nuclear reactors (e.g., a liquid-cooled fast reactor [LFR] or molten-salt reactor [MSR]) will be evaluated for coupling with TES in similar fashion, including the evaluation of their steady-state condition models and cost functions. The models presented herein showcase several design considerations, focusing on optimal deployment methodologies for achieving steady-state operation with minimum disruption to the nuclear power generation cycle. This report presents the results of steady state models developed using Aspen HYSYS®, wherein the thermal energy bypass for an NPP-TES coupling was varied up to 50%. The various components were sized using Aspen Process Economic Analyzer (APEA) and Aspen Exchanger Design and Rating (EDR), when applicable. Cost functions from these models were developed using the latest publicly available data obtained from APEA V11. The current steady-state models and cost functions provide a baseline for additional work focusing on dynamic operation and process optimization by using Idaho National Laboratory (INL)’s Framework for Optimization of Resources and Economics (FORCE) tools to evaluate the technoeconomic viability and transient operations of TES-coupled A-NPPs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Counter gravity heat pipe techniques

A pump assisted heat pipe may combine the low mass flow rate required of latent heat pipe transfer loops with a hermetically sealed pump to overcome the typical heat pipe capillary limit. This may result in a device with substantially higher heat transfer capacity over conventional pumped single-phase loops, heat pipes, loop heat pipes, and capillary pumped loops with very modest power requirements to operate. Further, one or more embodiments overcome the gravitation limitations in the conventional heat pipe configuration, e.g., when the heat addition zone is above the heat rejection zone, the capillary forces are required to transfer the liquid from the heat rejection zone to the heat addition zone against gravity.

Reid, Robert S.↗
DOE OSTI2024

Counter gravity heat pipe techniques

A pump assisted heat pipe may combine the low mass flow rate required of latent heat pipe transfer loops with a hermetically sealed pump to overcome the typical heat pipe capillary limit. This may result in a device with substantially higher heat transfer capacity over conventional pumped single-phase loops, heat pipes, loop heat pipes, and capillary pumped loops with very modest power requirements to operate. Further, one or more embodiments overcome the gravitation limitations in the conventional heat pipe configuration, e.g., when the heat addition zone is above the heat rejection zone, the capillary forces are required to transfer the liquid from the heat rejection zone to the heat addition zone against gravity.

Reid, Robert S.↗
DOE OSTI2022

Effects of oxygen on the adsorption/oxidation of aqueous Sb(III) by Fe-loaded biochar: An X-ray absorption spectroscopy study

Fe-loaded biochar (FeBC) has been considered for Sb(III) adsorption, but the effects of oxygen (O 2 ) on the adsorption need further investigation. Liquid-/solid-phase analyses were conducted to investigate the role of O 2 in the Sb(III) adsorption by FeBC. The adsorption was best described by the pseudo-second-order (PSO) model for kinetic results and by the Langmuir model for thermodynamic results. More than 96.8 % of Sb(III) was adsorbed by FeBC, and available O 2 increased the liquid-phase Sb(III) oxidation efficiency by 2.1–7.5 times. The peak changes at ~1640 and 3450 cm -1 in FTIR spectra indicated the occurrence of inner-sphere complexation between Sb(III)/Sb(V) and hydroxyl (–OH)/carboxyl (–COOH) groups in FeBC under aerobic and anaerobic conditions. Fe/Sb X-ray absorption spectroscopy (XAS) analysis results showed aqueous Sb(III) complexed to the edge-sharing Fe(III)-O-Fe(III) in FeBC. Regardless of whether O 2 was available or not, solid-phase edge-sharing Fe(III)-O-Sb(V) complexes (~3.05 Å), which had lower toxicity and migration ability than aqueous Sb(III), formed through a ligand-to-metal charge-transfer (LMCT) process. More than 91 % of adsorbed Sb(III) was oxidized to edge-sharing Fe(III)-O-Sb(V) complexes in 3 h. Additionally, the Sb(V) from liquid-phase oxidation could also directly complex to the Fe(III)-O-Fe(III) and form edge-sharing Fe(III)-O-Sb(V) complexes. Here these results provide evidence to inform further FeBC application for the Sb-contaminated water treatment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Biopower: Impact of Biofuels Deployment to Replace Petroleum Liquids in Stationary Power Applications

Petroleum-based liquids are used in a portion of power generation applications in the United States, predominantly in the New England, Middle Atlantic, South Atlantic, and Pacific-Noncontiguous regions. Power plants that burn petroleum liquids, such as distillate or residual fuel oils, are generally used for short periods to accommodate peak electricity demands. The Energy Information Administration (EIA) estimated the U.S. consumption of petroleum liquids for electricity generation at 27 million barrels in 2018, representing a cost of $2.4 billion annually. This study assesses the potential to displace all or part of the petroleum liquids in U.S. power generation with biofuels. The biofuels for this application are assumed to be derived from terrestrial feedstocks, with conversion routes of both fast pyrolysis (bio-oil) and hydrothermal liquefaction (bio-crude). Regional models were used to assess the availability and cost of three different base materials: clean wood, forest residues, and corn stover; each was evaluated in the laboratory at small or experimental scales for conversion to bio-oil or bio-crude. The estimated biofuel production quantities depend on equivalent heating versus the current heavy fuel. In this report, the availability of each type of biomass for each section of the U.S. Census division is estimated using a conservative broker price (in each case) of $ 80 per dry tonne. The results show that the petroleum-liquid power generation in each of the Census Divisions could be supplied by one or more of the feedstocks evaluated. For all regions, clean wood supplies (only) could provide ample supply. For all but two regions (Middle Atlantic and New England), forest residues alone are sufficient. Finally, for all regions but three (Middle Atlantic, New England, and South Atlantic), corn stover alone is adequate. The Minimum Fuel Selling Price (MFSP) of bio-oil and bio-crude were also estimated for each feedstock type and Census Division. This analysis showed that fast pyrolysis bio-oil projections to be lower (14% on average) than current wholesale petroleum-based heating oil prices in each of the regions, assuming 100 dry tonnes/day processing capacity. However, bio-crude predictions were significantly higher (2X) in all cases. The effect of biorefinery size was also quantified. Based on the preliminary results in this study, it is apparent the biofuels could be an economical alternative for current petroleum liquids in U.S. power generation. However, additional research is needed to determine the necessary biofuel characteristics to support existing generation equipment. It is recommended that both power generation and biofuel production stakeholders to be engaged to outline the research and testing needed to identify the technical hurdles to enable the opportunity.

02 PETROLEUM↗
DOE OSTI2022

In Situ Microstructure Characterization of Potassium Di-Phosphate (KDP) Densification during Cold Sintering

In order for ceramic additive manufacturing (AM) to achieve its full potential, it is increasingly important to develop a more rigorous understanding of fundamental phenomena that govern the kinetics and thermodynamics of ceramic AM processes. In the case of additive build processes, such as direct ink write and ceramic extrusion, methods for densifying the resulting green-body product need to be considered to complement the efficiencies of ceramics AM, itself. One densification route, at least for monolithic components, built layer-by-layer, is offered by the recently developed cold sintering process, whereby high-density final product is achieved through addition of a small amount of liquid solvent and application of modest uniaxial compressive stress at relatively low temperature. In situ small-angle X-ray scattering methods and X-ray diffraction have been applied to characterize and quantify the pore morphology evolution during cold sintering for a model system: potassium di-phosphate, KH 2 PO 4 (KDP). It is shown that both temperature and applied stress affect the densification rate, but stress has a stronger effect on the evolving morphology. A regime with an approximate linear densification rate can be identified, yielding an effective densification activation energy of ≈90 kJ/mol.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mass transport limitations in polymer electrolyte water electrolyzers using spatially-resolved current measurement

Here this work utilizes spatially-resolved current measurements to provide insight into mass transport limitations in electrolyzers that are not observable from traditional polarization measurement. In this study, two types of flow-fields (parallel and triple-serpentine) and two types of diffusion media (patterned porous thin titanium foil LGDLs and Ir-coated titanium felt PTLs) were examined. A non-uniform current distribution dominated by mass transport limitations was observed to be instigated by the restriction of liquid water transport to catalyst sites. Additionally, conditions are revealed which yield similar polarization performance but dissimilar current distributions. In such cases, the transport limitations for different architectures and porous media affect polarization in different regions of the active area. Furthermore, the triple-serpentine flow-field used in this study performs better than the parallel flow-field under mass transport limited operating conditions. This indicates that the parallel flow-field used in this study is more susceptible to starvation than the triple-serpentine flow-field for the electrolyzer studied.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

3D Printing ofThermally Responsive Shape Memory LiquidCrystalline Epoxy Networks

Abstract A two-component liquid crystalline epoxy network (LCEN) with shape memory behavior was developed and evaluated as a candidate material for 3D printing. The cure kinetics of the uncured material and the shape memory properties of the cured LCEN were investigated by using parallel plate rheology and dynamic mechanical analysis, respectively. A commercially available fumed silica additive was introduced to the neat, uncured material to improve the rheological properties for 3D printing. The addition of fumed silica was found to increase the yield stress, shear-thinning behavior, and toughness of the uncured epoxy ink. Polarized light microscopy, differential scanning calorimetry, and wide-angle X-ray scattering measurements between the neat and additive-modified LCEN suggested a reduction in liquid crystalline alignment in the modified LCEN, owing to interactions between crystalline domains and fumed silica, which in turn influenced the mechanical behavior. Overall, the additive was found to be successful in preserving the shape memory properties of LCEN while improving its printability.

Chemistry↗
DOE OSTI2021

A two-phase three-field modeling framework for heat pipe application in nuclear reactors

Heat pipes and two-phase thermosyphons are highly efficient heat transfer devices utilizing continuous evaporation and condensation of working fluid for two-phase heat transport in closed systems. Because of the nearly isothermal and fully passive phase-change heat transfer mechanism, heat pipes and thermosyphons have found many applications in nuclear engineering, space technologies, and other energy systems. High-temperature heat pipes are used in nuclear microreactors to remove fission power from the primary system and are coupled with power conversion systems or process heat applications. Modeling of the two-phase flow phenomena inside a heat pipe is essential to its design and safety analysis. In this study, a comprehensive one-dimensional two-phase three-field flow model has been developed for the analysis of heat pipes in normal operation conditions and transients. The conservation or field equations of mass, momentum, and energy were developed for the liquid film, vapor, and droplet. In addition, constitutive models or correlations were reviewed thoroughly and provided for the closure of the three-field equations. Specific constitutive equations regarding interfacial mass and heat transfer at two interfaces, namely film-gas interface and gas-droplet interface, were reviewed for droplet entrainment and deposition rates as well as film and droplet evaporation rates. Furthermore, mechanistic correlations of annular flow film thickness were recommended for the modeling of the thermosyphons without a wick as a critical constitutive correlation. Furthermore, experimental data needs from new experiments using a prototype working fluid or surrogate fluids for the model validation of high-temperature heat pipes in microreactors were recommended for future research.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Thermodynamic modeling of KCl-PrCl 3 and KCl-LiCl-PrCl 3 systems

Molten salt electrolysis can recover the actinides from spent nuclear fuels, and it involves a eutectic LiCl-KCl in molten form as an electrolyte. During reprocessing, the concentration of fission products such as La, Nd, Pr, etc., increases and affects the recovery efficiency of the electrolyte. In this work, thermodynamic modeling of KCl-PrCl 3 and KCl-LiCl-PrCl 3 systems was carried out using the CALPHAD (Calculation of Phase Diagrams) approach for the first time. The thermodynamic functions for the pure salts were taken from the SGTE (Scientific Group Thermodata Europe) Substances (SSUB) database. The experimental thermochemical and phase equilibria data available in the literature were used as input for the assessment of KCl-PrCl 3 and KCl-LiCl-PrCl 3 systems. The model parameters for the KCl-LiCl system were adjusted to include the new Gibbs energy descriptions for the pure salts. In addition, the sublattice model for the liquid phase in the LiCl-PrCl 3 system was modified and reassessed to ensure the model compatibility for higher-order extrapolation. There is a good agreement between the experimental and calculated thermochemical and phase diagram data for all the optimized constituent binaries and the ternary system. Furthermore, this work will be beneficial for determining the solubility limit of PrCl 3 in molten LiCl-KCl electrolytes and their thermodynamic properties for improving the efficiency of the pyrochemical process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Assessing Clouds in GFDL's AM4.0 With Different Microphysical Parameterizations Using the Satellite Simulator Package COSP

We evaluate cloud simulations using satellite simulators against multiple observational data sets. These simulators have been run within the Geophysical Fluid Dynamics Laboratory's Atmosphere Model version 4.0 (AM4.0), as well as an alternative configuration where a fully two‐moment Morrison‐Gettelman cloud microphysical parameterization with prognostic precipitation (MG2) is applied, denoted as AM4‐MG2. The modeled cloud spatial distributions, vertical profiles, phase partitioning, cloud‐to‐precipitation transitions, and radiative effects compare reasonably well with satellite observations. Model biases include the under‐prediction of total and low‐level clouds, especially optically thin/intermediate clouds with cloud optical depth of less than 23, but the over‐prediction of thick clouds, indicating “too few, too bright” biases. These biases counteract each other, and give rise to reasonable estimates of cloud radiative effects. The underestimate of low‐level clouds is associated with too early and too frequent drizzle/precipitation formation. The precipitation bias is improved in AM4‐MG2, where the autoconversion scheme initiates the precipitation more realistically. There also exist discrepancies between models and observations for midlevel and high‐level clouds. Additional biases include the underestimate of liquid cloud fraction and the overestimate of ice cloud fraction.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Calculation of the detonation state of HN 3 with quantum accuracy

HN 3 is a unique liquid energetic material that exhibits ultrafast detonation chemistry and a transition to metallic states during detonation. We combine the Chebyshev interaction model for efficient simulation (ChIMES) many-body reactive force field and the extended-Lagrangian multiscale shock technique molecular dynamics method to calculate the detonation properties of HN 3 with the accuracy of Kohn–Sham density-functional theory. ChIMES is based on a Chebyshev polynomial expansion and can accurately reproduce density-functional theory molecular dynamics (DFT-MD) simulations for a wide range of unreactive and decomposition conditions of liquid HN 3 . We show that addition of random displacement configurations and the energies of gas-phase equilibrium products in the training set allows ChIMES to efficiently explore the complex potential energy surface. Schemes for selecting force field parameters and the inclusion of stress tensor and energy data in the training set are examined. Structural and dynamical properties and chemistry predictions for the resulting models are benchmarked against DFT-MD. We demonstrate that the inclusion of explicit four-body energy terms is necessary to capture the potential energy surface across a wide range of conditions. Our results generally retain the accuracy of DFT-MD while yielding a high degree of computational efficiency, allowing simulations to approach orders of magnitude larger time and spatial scales. The techniques and recipes for MD model creation we present allow for direct simulation of nanosecond shock compression experiments and calculation of the detonation properties of materials with the accuracy of Kohn–Sham density-functional theory.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Unravel unusual hardening behavior of a Pd–Ni–P metallic glass in its supercooled liquid region

Monolithic metallic glasses often exhibit work softening induced by high atom mobility in the supercooled liquid region in tension. In this work, we report an unusual viscous flow of the Pd 42.5 Ni 42.5 P 15 metallic glass in its supercooled liquid region, which is characterized by a remarkable hardening behavior with decent plasticity during tension. To unravel the causes of this unusual hardening, we conducted structural and thermodynamic analyses by employing several experiments, including dynamic mechanical analysis, differential scanning calorimetry, high-resolution transmission electron microscopy, and in situ heating synchrotron high-energy x-ray diffraction. It was found that the unusual hardening behavior was attributed to structural ordering during deformation, rather than nanocrystallization or structural relaxation observed, sometimes, in metallic glasses deformed in supercooled liquid region. We also incorporated an additional work hardening region in the modified deformation map for metallic glasses.

36 MATERIALS SCIENCE↗