Search NASA⌕ Search

SEARCH · Search NASA

Results for “maximum likelihood estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Estimation of the differential pulse propagation times in two-color laser ranging systems

Two-color laser ranging systems can be used to determine the atmospheric delay by measuring the difference in propagation times between two optical pulses transmitted at two different wavelengths. In this paper, the performance of a cross-correlation technique for estimating the differential propagation time is analyzed by considering both speckle and shot noise. For the flat diffuse targets, the differential timing accuracy is highly dependent on the receiver bandwidth and the characteristics of the time-resolved speckle. At low signal levels, when the receiver bandwidth is chosen properly, the performance of the correlation estimator is comparable with that of the maximum-likelihood estimator. At high signal levels, however, speckle places a fundamental limit on the performance of the correlation estimator. For the cube-corner reflector arrays, timing performance is dominated by partially developed speckle. The differential propagation time cannot by resolved to better than the pulse widths of the received signals.

Im, K. E.↗

Transonic stability and control of aircraft using CFD methods

Implementation of a capability to calculate longitudinal short-period response in the CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) finite-difference code is described. The code, developed recently at the NASA Langley Research Center, is capable of solving steady and unsteady flows about complete aircraft configurations and is used primarily for aeroelastic calculations in the critical transonic speed range. The longitudinal short-period equations of motion in state-space form have been coupled to the time-accurate lift and moment calculated by the program. Transient responses to an elevator pulse for free-flying aircraft demonstrate the new capability. A trim routine is also added to the code to obtain trim automatically during steady-state flow field convergence. Stability and control derivatives are estimated from the calculated transient response by a maximum likelihood estimation program. Results for a fighter configuration and a general aviation configuration are presented to assess the capability.

Vinh, Lam-Son↗

X-Ray Detection and Processing Models for Spacecraft Navigation and Timing

The current primary method of deepspace navigation is the NASA Deep Space Network (DSN). High-performance navigation is achieved using Delta Differential One-Way Range techniques that utilize simultaneous observations from multiple DSN sites, and incorporate observations of quasars near the line-of-sight to a spacecraft in order to improve the range and angle measurement accuracies. Over the past four decades, x-ray astronomers have identified a number of xray pulsars with pulsed emissions having stabilities comparable to atomic clocks. The x-ray pulsar-based navigation and time determination (XNAV) system uses phase measurements from these sources to establish autonomously the position of the detector, and thus the spacecraft, relative to a known reference frame, much as the Global Positioning System (GPS) uses phase measurements from radio signals from several satellites to establish the position of the user relative to an Earth-centered fixed frame of reference. While a GPS receiver uses an antenna to detect the radio signals, XNAV uses a detector array to capture the individual xray photons from the x-ray pulsars. The navigation solution relies on detailed xray source models, signal processing, navigation and timing algorithms, and analytical tools that form the basis of an autonomous XNAV system. Through previous XNAV development efforts, some techniques have been established to utilize a pulsar pulse time-of-arrival (TOA) measurement to correct a position estimate. One well-studied approach, based upon Kalman filter methods, optimally adjusts a dynamic orbit propagation solution based upon the offset in measured and predicted pulse TOA. In this delta position estimator scheme, previously estimated values of spacecraft position and velocity are utilized from an onboard orbit propagator. Using these estimated values, the detected arrival times at the spacecraft of pulses from a pulsar are compared to the predicted arrival times defined by the pulsar s pulse timing model. A discrepancy provides an estimate of the spacecraft position offset, since an error in position will relate to the measured time offset of a pulse along the line of sight to the pulsar. XNAV researchers have been developing additional enhanced approaches to process the photon TOAs to arrive at an estimate of spacecraft position, including those using maximum-likelihood estimation, digital phase locked loops, and "single photon processing" schemes that utilize all available time data associated with each photon. Using pulsars from separate, non-coplanar locations provides range and range-rate measurements in each pulsar s direction. Combining these different pulsar measurements solves for offsets in position and velocity in three dimensions, and provides accurate overall navigation for deep space vehicles.

Sheikh, Suneel↗

Probabilities and statistics for backscatter estimates obtained by a scatterometer with applications to new scatterometer design data

The values of the Normalized Radar Backscattering Cross Section (NRCS), sigma (o), obtained by a scatterometer are random variables whose variance is a known function of the expected value. The probability density function can be obtained from the normal distribution. Models for the expected value obtain it as a function of the properties of the waves on the ocean and the winds that generated the waves. Point estimates of the expected value were found from various statistics given the parameters that define the probability density function for each value. Random intervals were derived with a preassigned probability of containing that value. A statistical test to determine whether or not successive values of sigma (o) are truly independent was derived. The maximum likelihood estimates for wind speed and direction were found, given a model for backscatter as a function of the properties of the waves on the ocean. These estimates are biased as a result of the terms in the equation that involve natural logarithms, and calculations of the point estimates of the maximum likelihood values are used to show that the contributions of the logarithmic terms are negligible and that the terms can be omitted.

Pierson, Willard J., Jr.↗

Kumaraswamy distribution: different methods of estimation

This paper addresses different methods of estimation of the unknown parameters of a two-parameter Kumaraswamy distribution from a frequentist point of view. We briefly describe ten different frequentist approaches, namely, maximum likelihood estimators, moments estimators, L-moments estimators, percentile based estimators, least squares estimators, weighted least squares estimators, maximum product of spacings estimators, Cramér–von-Mises estimators, Anderson–Darling estimators and right tailed Anderson–Darling estimators. Monte Carlo simulations and two real data applications are performed to compare the performances of the estimators for both small and large samples.

97 MATHEMATICS AND COMPUTING↗

Fast Gaussian Process Estimation for Large-Scale In Situ Inference using Convolutional Neural Networks

Exascale computing will bring with it significant I/O limitations. One foreseeable consequence of such restrictions is that the user can save only a small fraction of complex simulation data to disk for subsequent analysis. An alternative is to fit statistical models to data in situ, that is, inside the simulation as it runs. This option requires extremely fast statistical estimation to avoid slowing down the simulation. Gaussian processes (GPs) have state-of-the-art predictive performance for modeling spatial data. However, standard estimation methods for GPs scale quite poorly to large data sets as parameter estimation requires inverting a covariance matrix to the size of the data set. In the presented work, we use a convolutional neural network (CNN) to predict the GP parameters for a spatial data set, from a simulation or otherwise, rather than optimize the parameters directly. Here, our presented case study models spatial data from E3SM, the Department of Energy’s Exascale climate model. The CNN is trained on synthetic data simulated from GP models with known parameters and then applied to data from the climate simulation. In the presented examples, the neural network scheme produces parameter estimates that compare well with standard methods such as maximum likelihood estimation in predictive performance but is obtained four orders of magnitude faster.

big data↗

A new method of boundary parameter estimation for a two-dimensional diffusion system under noisy observations

The purpose of this paper is to establish a method for identifying unknown parameters involved in the boundary state of a class of diffusion systems under noisy observations. A mathematical model of the system dynamics is given by a two-dimensional diffusion equation. Noisy observations are made by sensors allocated on the system boundary. Starting with the mathematical model mentioned above, an online parameter estimation algorithm is proposed within the framework of the maximum likelihood estimation. Existence of the optimal solution and related necessary conditions are discussed. By solving a local variation of the cost functional with respect to the perturbation of parameters, the estimation mechanism is proposed in a form of recursive computations. Finally, the feasibility of the estimator proposed here is demonstrated through results of digital simulation experiments.

Sunahara, Y.↗

A method of boundary parameter estimation for a two-dimensional diffusion system under noisy observations

The purpose of this paper is to establish a method for identifying unknown parameters involved in the boundary state of a class of diffusion systems under noisy observations. A mathematical model of the system dynamics is given by a two-dimensional diffusion equation. Noisy observations are made by sensors allocated on the system boundary. Starting with the mathematical model mentioned above, an online parameter estimation algorithm is proposed within the framework of the maximum likelihood estimation. Existence of the optimal solution and related necessary conditions are discussed. By solving a local variation of the cost functional with respect to the perturbation of parameters, the estimation mechanism is proposed in a form of recursive computations. Finally, the feasibility of the estimator proposed here is demonstrated through results of digital simulation experiments.

Sunahara, Y.↗

Improved geometric calibration of the SIR-C data

Errors in the determination of the platform state vector (position and velocity) limit the accuracy with which individual pixels in a SAR (synthetic aperture radar) image can be located. A method of updating the state vector based on the SAR data is described. The algorithm combines reference targets at known locations with the estimates available from the mission control center, utilizing a maximum likelihood estimator. The targets can be located at calibration sites or be easily recognizable targets of opportunity. The accuracy of the update depends on the number of targets, their geometry, and the accuracy of their position determination. The algorithm is tested using Seasat SAR data. High-accuracy state vectors were perturbed by Gaussian distributed errors with standard deviations and cross-correlations based on worst-case expectations for SIR-C (Shuttle Imaging Radar). Tests using ground targets located in topographic maps (1:24,000) showed that state vector position errors on the order of 300-400 m and velocity accuracies of 2-3 m/s are readily achievable.

Madsen, S. N.↗

Coherent lidar design and performance verification

The verification of LAWS beam alignment in space can be achieved by a measurement of heterodyne efficiency using the surface return. The crucial element is a direct detection signal that can be identified for each surface return. This should be satisfied for LAWS but will not be satisfied for descoped LAWS. The performance of algorithms for velocity estimation can be described with two basic parameters: the number of coherently detected photo-electrons per estimate and the number of independent signal samples per estimate. The average error of spectral domain velocity estimation algorithms are bounded by a new periodogram Cramer-Rao Bound. Comparison of the periodogram CRB with the exact CRB indicates a factor of two improvement in velocity accuracy is possible using non-spectral domain estimators. This improvement has been demonstrated with a maximum-likelihood estimator. The comparison of velocity estimation algorithms for 2 and 10 micron coherent lidar was performed by assuming all the system design parameters are fixed and the signal statistics are dominated by a 1 m/s rms wind fluctuation over the range gate. The beam alignment requirements for 2 micron are much more severe than for a 10 micron lidar. The effects of the random backscattered field on estimating the alignment error is a major problem for space based lidar operation, especially if the heterodyne efficiency cannot be estimated. For LAWS, the biggest science payoff would result from a short transmitted pulse, on the order of 0.5 microseconds instead of 3 microseconds. The numerically errors for simulation of laser propagation in the atmosphere have been determined as a joint project with the University of California, San Diego. Useful scaling laws were obtained for Kolmogorov atmospheric refractive turbulence and an atmospheric refractive turbulence characterized with an inner scale. This permits verification of the simulation procedure which is essential for the evaluation of the effects of refractive turbulence on coherent Doppler lidar systems. The analysis of 2 micron Doppler lidar data from Coherent Technologies, Inc. (CTI) has demonstrated many of the advantages of doppler lidar measurements of boundary layer winds. The effects of wind shear and wind turbulence over the pulse volume are probably the dominant source of the reduced performance. The effects of wind shear and wind turbulence on the statistical description of doppler lidar data has been derived and calculated.

Frehlich, Rod↗

Optimal design and use of retry in fault tolerant real-time computer systems

A new method to determin an optimal retry policy and for use in retry of fault characterization is presented. An optimal retry policy for a given fault characteristic, which determines the maximum allowable retry durations to minimize the total task completion time was derived. The combined fault characterization and retry decision, in which the characteristics of fault are estimated simultaneously with the determination of the optimal retry policy were carried out. Two solution approaches were developed, one based on the point estimation and the other on the Bayes sequential decision. The maximum likelihood estimators are used for the first approach, and the backward induction for testing hypotheses in the second approach. Numerical examples in which all the durations associated with faults have monotone hazard functions, e.g., exponential, Weibull and gamma distributions are presented. These are standard distributions commonly used for modeling analysis and faults.

Lee, Y. H.↗

Distributed parameter estimation for large beam-like structures for general inputs

In this paper, maximum likelihood estimation for distributed parameter models of large flexible structures has been formulated. Distributed parameter models involve far fewer unknown parameters than independent modal characteristics of finite element models. The closed-form solutions for the partial differential equations with general forced inputs have been derived. The closed-form expressions of the sensitivity functions lead to highly efficient algorithms for analyzing ground or on-orbit test results. Numerical simulations with impulse and step inputs to the NASA Mini-MAST trust have been demonstrated. The estimations of modal properties involve its longitudinal elongation modes, lateral bending modes and torsional modes. The results show that distributed parameter models are promising in the parameter estimation of large flexible structures.

Shen, Ji-Yao↗

Maximum Likelihood Source Localization Using Elpasolite as a Dual Gamma Neutron Directional Detector

The problem of accurately detecting extremely low levels of nuclear radiation is rapidly increasing in importance in nuclear counter-proliferation, verification, and environmental and waste management. Because the 239Pu gamma signature may be weak, for instance, even when compared to the natural terrestrial background, coincidence counting with the 239Pu neutron signature may improve overall 239Pu detection sensitivity. However, systems with sufficient multiple-particle detectors require demonstration that the increased sensitivity be sufficiently high to overcome added cost and weight. We report the results of measurements and calculations to determine sensitivity that can be gained in detecting low levels of nuclear radiation from use of a relatively new detector technology based on elpasolite crystals. We have performed investigations exploring cerium (Ce3+)-doped elpasolites Cs2LiYCl6:Ce3+0.5% (CLYC) and Cs2LiLa(Br6)90%(Cl6)10%:Ce3+0.5% (CLLBC:Ce). These materials can provide energy resolution (r(E) = 2.35σ(E)/E) as good as 2.9% at 662 keV (FWHM). The crystals show an excellent neutron and gamma radiation response. The goals of the investigation were to set up the neutron/gamma pulse shape discrimination electronics for elpasolite detectors; perform limited static source benchmarking, testing, and evaluation to validate system performance; and explore application of a maximum likelihood algorithm for source location. Data were measured and processed through a maximum likelihood estimation algorithm, providing a direction to the radioactive source for each individual position. The estimated directions were good representations for the actual directions to the radioactive source. This paper summarizes the maximum likelihood results for our elpasolite system.

maximum likelihood, radiation detectors, neutron d↗

Aircraft Parameter Estimation Considering Process and Measurement Noise

A practical formulation is proposed for parameter estimation using the filter-error method, which is a maximum-likelihood estimator for dynamic systems having both process and measurement noise inputs. The novelty of the proposed formulation is that by accurately estimating the measurement noise covariance matrix using a time series analysis method, the remaining unknowns (which include the unknown parameters in the state-space matrices and the process noise covariance matrix) become decorrelated and can be estimated simultaneously in a straightforward manner. The approach is demonstrated using simulation data and flight test data from a subscale airplane. Results indicate that proposed algorithm can obtain accurate modeling results when both measurement noise and process noise are present in the data.

Kalman filter↗

Scalable computations for nonstationary Gaussian processes

Nonstationary Gaussian process models can capture complex spatially varying dependence structures in spatial datasets. However, the large number of observations in modern datasets makes fitting such models computationally intractable with conventional dense linear algebra. In addition, derivative-free or even first-order optimization methods can be very slow to converge when estimating many spatially varying parameters. In this paper, we present a computational framework which couples an algebraic block diagonal plus low-rank covariance matrix approximation with stochastic trace estimation to facilitate the efficient use of second-order solvers for maximum likelihood estimation of Gaussian process models with many parameters. We demonstrate the effectiveness of these methods by simultaneously fitting 192 parameters in the popular nonstationary model of Paciorek and Schervish using 107,600 sea surface temperature anomaly measurements.

97 MATHEMATICS AND COMPUTING↗

Estimation of aerodynamic characteristics from dynamic flight test data

Significant effort was spent in estimating unknown aircraft coefficients, such as stability and control derivatives from dynamic flight maneuvers. The techniques used to estimate these coefficients are becoming increasingly complex; however, these techniques make it possible to obtain estimates of coefficients that in the past were nearly impossible to obtain. A survey of the investigations that were undertaken to obtain estimates of coefficients from dynamic flight maneuvers is presented. One method, the maximum likelihood estimation technique, is described briefly and some of the successful applications of the technique are presented. Possible techniques for analyzing responses obtained in the stall/spin regime are discussed. Recent data obtained in the stall/spin flight regime are presented along with a discussion of how some basic results can be obtained with simple analysis techniques.

Liff, K. W.↗

A Model for Measurements of Lognormally Distributed Environmental Contaminants

This paper proposes a more nearly reasonable model for the actual measurement distribution, called here the “Davis Mixed Model” (DMM). The DMM is derived by multiplying the probability density function of unobservable actual concentrations (assumed LN) by the conditional density of measurements given the concentrations (assumed heteroscedastic normal), and then integrating to obtain the marginal distribution of the observable measurements. The DMM is complicated and analytically intractable; its probability density function (PDF) is itself an integral, for example, and closed-form expressions for percentiles, let alone estimators, do not exist. The DMM can be fit to data via Maximum Likelihood Estimation (MLE), however, and a fitted model can be used to generate data for evaluating the actual performance of candidate UTL or other estimation procedures. The Industrial Hygiene application motivating this work involves surface sampling surveys for removable beryllium (Be) contamination, with data from Inductively Coupled Plasma – Atomic Emission Spectroscopy (ICP-AES) analyses. Similar issues will arise quite generally with censored environmental data for other contaminants and analytical methods. The conclusions presented in this paper focus on the regions of the DMM parameter space arising in surveying numerous Department of Energy (DOE) facilities associated with the Nevada Test Site (NTS).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗