Results for “mechanical performance” — Page 11

DOE OSTI2023

Microstructure and texture evolution of friction stir lap welded dissimilar multi-aluminum stack

Here this work investigates the microstructural evolution of a dissimilar multiple-aluminum alloy stack (AA7055, AA7055, AA6022) produced by friction stir lap welding (FSLW). A through-thickness analyses of grain orientation map, grain size and distribution, strain distribution, and texture evolution by electron backscattered diffraction-based characterization technique were performed. Two different welding parameters (combination of tool rotation and traverse speed) were used to study the effects of the welding parameters on these microstructural characteristics. The study shows that higher welding speed and higher rotation speed of the FSLW tool yield finer grains. FSLW resulted in shear texture formation in the weld regions due to high welding speeds. This texture development in the nugget zone is consistent with shear deformation, and (111) pole figures show ideal shear texture components. The Stir Zone (SZ) exhibits shear texture (A/A ̅ and B/B ̅ components), consistent with other shear-assisted processes. Recrystallization mechanisms observed are CDRX in SZ and DDRX in TMAZ (Thermo-Mechanically Affected Zone). Interface analysis reveals the presence of oxide layers between different aluminum sheets, affecting joint mechanical performance. The mechanical property of the lap welded joints was presented in terms of microhardness distribution across the weld cross section. Slightly higher hardness in higher speed welding setup was observed throughout the SZ and AA6022 layer, indicating greater grain refinement and uniform grain structure distribution.

36 MATERIALS SCIENCE↗

NASA NTRS2010

Comparison of Autoclave and Out-of-Autoclave Composites

The National Aeronautics and Space Administration (NASA) Exploration Systems Mission Directorate initiated an Advanced Composite Technology Project through the Exploration Technology Development Program in order to support the polymer composite needs for future heavy lift launch architectures. As an example, the large composite dry structural applications on Ares V inspired the evaluation of autoclave and out-of-autoclave (OOA) composite materials. A NASA and industry team selected the most appropriate materials based on component requirements for a heavy lift launch vehicle. Autoclaved and OOA composites were fabricated and results will highlight differences in processing conditions, laminate quality, as well as initial room temperature thermal and mechanical performance. Results from this study compare solid laminates that were both fiber-placed and hand-laid. Due to the large size of heavy-lift launch vehicle composite structures, there is significant potential that the uncured composite material or prepreg will experience significant out-life during component fabrication. Therefore, prepreg out-life was a critical factor examined in this comparison. In order to rigorously test material suppliers recommended out-life, the NASA/Industry team extended the out-time of the uncured composite prepreg to values that were approximately 50% beyond the manufacturers out-time limits. Early results indicate that the OOA prepreg composite materials suffered in both composite quality and mechanical property performance from their extended out-time. However, the OOA materials performed similarly to the autoclaved composites when processed within a few days of exposure to ambient "shop" floor handling. Follow on studies evaluating autoclave and OOA aluminum honeycomb core sandwich composites are planned.

Sutter, James K.↗

DOE OSTI2024

Coal-derived electrically conductive asphalt pavements for snow/ice melting: From laboratory to field

Timely removal of ice and snow from roads is critical to safe, fast, and uninterrupted transportation networks in cold regions. Constructing electrically conductive asphalt pavements to melt the ice and snow on the roads through resistive eating is an emerging alternative technology to traditional snow/ice removal approaches such as utilizing snowplow machines and deicing chemicals. Carbon-based fibers and fillers including carbon fiber and graphite have been widely reported to make electrically conductive hot mix asphalt mixtures for pavement snow/ice-melting applications. This study aimed to develop and demonstrate a novel type of electrically conductive asphalt pavements for snow/ice-melting, which utilizes electrically conductive cold mix asphalt (CMA) mixtures incorporating coal-derived carbon-based coke aggregate as resistive heating elements. Both laboratory experiments and field tests were conducted to investigate the electrical, mechanical, and thermal properties of such electrically conductive asphalt mixtures and pavements. The laboratory experiment results indicated that the electrically conductive CMA mixtures incorporating coke aggregate had sufficiently high electrical conductivity and satisfactory mechanical performance and the pavement prototype slab utilizing a thin layer of such CMA mixtures could successfully raise the pavement surface temperatures to 8.3–11.7 °C rom a low temperature of –5 °C with an input power density of 473 W/m 2 . The field test results showed that the full-scale coal-derived electrically conductive asphalt pavements were able to increase the pavement surface temperatures when electricity was applied, but the magnitude of temperature increase was highly dependent on the power density. Furthermore, it is promising to use coke aggregate to construct coal-derived electrically conductive asphalt pavements for snow/ice melting.

36 MATERIALS SCIENCE↗

NASA NTRS2023

3D Printed TiO 2 Negative Electrodes for Sodium-Ion and Lithium-ion Batteries using Vat Photopolymerization

Additive manufacturing, also called 3D printing, represents a unique approach to develop three dimensional shape-conformable batteries with enhanced electrodes, specific surface area, improved ion diffusion, and power. For the first time, the formulation of a composite photocurable resin loaded with battery electrochemically active components was designed to feed a vat photopolymerization (VPP) 3D printer. In direct alignment with NASA’s Artemis mission goals to develop sustainable lunar energy storage infrastructure necessary to support long-term human operations, TiO 2 was here selected as an active material for the negative electrode for sodium-ion and lithium-ion batteries due to its abundance on the lunar surface. The TiO 2 loading in the composite photocurable resin and in the resulting VPP-printed negative electrode was increased as high as possible to enhance the electrochemical performance, while simultaneously ensuring the printability and acceptable mechanical strength for sample handling. The effect of thermal post-processing on the electrical, electrochemical and mechanical performance is reported. Finally, a configurational study is implemented to identify the impact of two different electrode designs (cubic and gyroid lattice unit cells) on the electrochemical performance. This work addresses the difficulties related to the introduction of solid particles within a VPP photocurable resin and the need for a compromise between the electrochemical performances and printability to obtain fully functional VPP-printed electrodes.

sodium-ion battery↗

DOE OSTI2020

Non-destructive simulation of node defects in additively manufactured lattice structures

Additive Manufacturing (AM), commonly referred to as 3D printing, offers the ability to not only fabricate geometrically complex lattice structures but parts in which lattice topologies in-fill volumes bounded by complex surface geometries. However, current AM processes produce defects on the strut and node elements which make up the lattice structure. This creates an inherent difference between the as-designed and as-fabricated geometries, which negatively affects predictions (via numerical simulation) of the lattice’s mechanical performance. Although experimental and numerical analysis of an AM lattice’s bulk structure, unit cell and struts have been performed, there exists almost no research data on the mechanical response of the individual as-manufactured lattice node elements. Here we propose a methodology that, for the first time, allows non-destructive quantification of the mechanical response of node elements within an as-manufactured lattice structure. A custom-developed tool is used to extract and classify each individual node geometry from micro-computed tomography scans of an AM fabricated lattice. Voxel-based finite element meshes are generated for numerical simulation and the mechanical response distribution is compared to that of the idealised computer-aided design model. The method demonstrates compatibility with Uncertainty Quantification methods that provide opportunities for efficient prediction of a population of nodal responses from sampled data. Overall, the non-destructive and automated nature of the node extraction and response evaluation is promising for its application in qualification and certification of additively manufactured lattice structures.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Mechanical Properties of Additively Manufactured 316L Stainless Steel Before and After Neutron Irradiation (FY21)

This report presents the materials property data of additively manufactured (AM) 316L stainless steel (SS) accumulated for the assessment of core materials in the Transformational Challenge Reactor (TCR) program. The TCR manufacturing approach includes using the laser powder bed fusion (LPBF) method for metallic (316L and Inconel 718) components. To assess the mechanical performance of printed components in reactor-relevant conditions and build a property database for the AM materials, mechanical tests and evaluations were performed before and after neutron irradiation. Miniature tensile specimens were irradiated in the High Flux Isotope Reactor to 0.2, 2, 8, and 10 dpa at target temperatures of 300 and 600°C. Postirradiation evaluation for the 0.2 and 2 dpa specimens was performed during FY20 and FY21, and the results are presented and discussed in this document.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

2D material-based layer transfer: Challenges and opportunities

For future of electronics such as bioelectronics, 3D integrated electronics, and bendable electronics, needs for flexibility and stackability of electronic products have substantially grown up. However, conventional wafer-based single-crystalline semiconductors cannot catch up with such trends because they are bound to the thick rigid wafers such that they are neither flexible nor stackable. Although polymer-based organic electronic materials are more compatible as they are mechanically complaint and less costly than inorganic counterparts, their electronic/photonic performance is substantially inferior to that of single-crystalline inorganic materials. For the past few decades, many different strategies to mitigate such performance-mechanical compliance dilemma by developing methods to obtain cheap, flexible, stackable, single-crystalline inorganic systems. In today’s talk, I will discuss about various strategies to realize such a dream electronic system and how these strategies unlock new ways of manufacturing advanced electronic systems. One of the most promising approaches is to fabricate freestanding ultrathin membranes from existing functional material wafers by peeling the active layers from the top. I will overview all freestanding membrane methods and especially dive deeply into 2D materials-based layer transfer (2DLT) technique that has been recently emerging as one of the very promising options. In the 2DLT process, one can produce single-crystalline freestanding membranes from 3D materials by performing remote epitaxy or van der Waals epitaxy on 2D materials followed by peeling active single-crystalline films from the 2D materials. I will discuss about the challenges and opportunities of this technology. In addition, I will present unprecedented artificial heterostructures that can be enabled by stacking those freestanding 3D material membranes.

Kim, Jeehwan↗

DOE OSTI2022

Two-dimensional material based layer transfer: challenges and opportunities

For future of electronics such as bioelectronics, 3D integrated electronics, and bendable electronics, needs for flexibility and stackability of electronic products have substantially grown up. However, conventional wafer-based single-crystalline semiconductors cannot catch up with such trends because they are bound to the thick rigid wafers such that they are neither flexible nor stackable. Although polymer-based organic electronic materials are more compatible as they are mechanically complaint and less costly than inorganic counterparts, their electronic/photonic performance is substantially inferior to that of single-crystalline inorganic materials. For the past few decades, many different strategies to mitigate such performance-mechanical compliance dilemma by developing methods to obtain cheap, flexible, stackable, single-crystalline inorganic systems. In today’s talk, I will discuss about various strategies to realize such a dream electronic system and how these strategies unlock new ways of manufacturing advanced electronic systems. One of the most promising approaches is to fabricate freestanding ultrathin membranes from existing functional material wafers by peeling the active layers from the top. I will overview all freestanding membrane methods and especially dive deeply into 2D materials-based layer transfer (2DLT) technique that has been recently emerging as one of the very promising options. In the 2DLT process, one can produce single-crystalline freestanding membranes from 3D materials by performing remote epitaxy or van der Waals epitaxy on 2D materials followed by peeling active single-crystalline films from the 2D materials. I will discuss about the challenges and opportunities of this technology. In addition, I will present unprecedented artificial heterostructures that can be enabled by stacking those freestanding 3D material membranes.

KIM, JEEHWAN↗

DOE OSTI2025

Design and Analysis of Short Period 2G-HTS Undulators

Recent advancements in second-generation high-temperature superconducting (2G-HTS) materials have opened new possibilities for superconducting undulator (SCU) technology, particularly in achieving shorter periods and higher magnetic fields. Here, this paper presents the design and analysis of a short-period, as small as 10 mm, 2G-HTS undulator, focusing on magnetic performance, mechanical force minimization, and quench protection. A force-balanced coil pack design is introduced to significantly reduce mechanical stresses on the conductors, eliminating the need for heavy support structures. Rapid prototyping techniques such as3D printing is employed to refine the design for scalability and manufacturability. Correction schemes for end-field effects are developed using a combination of 2G-HTS tapes and NbTi conductors to optimize field integrals. Simulation results demonstrated that optimized magnetic performance and enhanced mechanical stability, positioning 2G-HTS undulators as promising candidates for storage ring and free-electron based light sources.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2022

Advanced Heterogeneous Integration Enabled by 3D Freestanding Membranes—From Material Growths to Applications

For the future of electronics such as bioelectronics, 3D integrated electronics, and bendable electronics, the need for flexibility and stackability of electronic products has substantially grown up. However, conventional wafer-based single-crystalline semiconductors cannot catch up with such trends because they are bound to thick rigid wafers such that they are neither flexible nor stackable. Although polymer-based organic electronic materials are more compatible as they are mechanically compliant and less costly than inorganic counterparts, their electronic/photonic performance is substantially inferior to that of single-crystalline inorganic materials. Such performance-mechanical compliance dilemma could be resolved by developing methods to obtain cheap, flexible, stackable, single-crystalline inorganic systems. Such dream electronic systems could be realized by producing single-crystalline freestanding membranes. For the past few decades, various layer transfer techniques (a.k.a layer liftoff techniques) have been developed to produce single-crystalline freestanding membranes. In today's talk, I will present the survey of the layer liftoff techniques and go over how these strategies unlock new ways of manufacturing advanced electronic systems. In addition, I will introduce unprecedented artificial heterostructure devices enabled by stacking of those freestanding 3D material membranes, e.g., the world's smallest vertically-stacked full-color micro-LEDs, the world's best multiferroic devices, chip-less wireless e-skin, and reconfigurable hetero-integrated chips with AI accelerators.

Kim, Jeehwan↗

DOE OSTI2022

Advanced Heterogeneous Integration Enabled by 3D Freestanding Membranes—From Material Growths to Applications

For the future of electronics such as bioelectronics, 3D integrated electronics, and bendable electronics, the need for flexibility and stackability of electronic products has substantially grown up. However, conventional wafer-based single-crystalline semiconductors cannot catch up with such trends because they are bound to thick rigid wafers such that they are neither flexible nor stackable. Although polymer-based organic electronic materials are more compatible as they are mechanically compliant and less costly than inorganic counterparts, their electronic/photonic performance is substantially inferior to that of single-crystalline inorganic materials. Such performance-mechanical compliance dilemma could be resolved by developing methods to obtain cheap, flexible, stackable, single-crystalline inorganic systems. Such dream electronic systems could be realized by producing single-crystalline freestanding membranes. For the past few decades, various layer transfer techniques (a.k.a layer liftoff techniques) have been developed to produce single-crystalline freestanding membranes. In today's talk, I will present the survey of the layer liftoff techniques and go over how these strategies unlock new ways of manufacturing advanced electronic systems. In addition, I will introduce unprecedented artificial heterostructure devices enabled by stacking of those freestanding 3D material membranes, e.g., the world's smallest vertically-stacked full-color micro-LEDs, the world's best multiferroic devices, chip-less wireless e-skin, and reconfigurable hetero-integrated chips with AI accelerators.

Kim, Jeehwan↗

NASA NTRS1989

Near-field testing of the 15-meter hoop-column antenna

A 15-m-diameter antenna was tested to verify that dimensional tolerances for acceptable performance could be achieved and to verify structural, electromagnetic, and mechanical performance predictions. This antenna utilized the hoop column structure, a gold plated molybdenum mesh reflector, and 96 control cables to adjust the reflector conformance with a paraboloid. The dimensional conformance of the antenna structure and surface was measured with metric camera and theodolites. Near field pattern data were used to assess the electromagnetic performance at five frequencies from 2.225 to 11.6 GHz. The reflector surface was adjusted to greatly improve electromagnetic performance with a finite element model and the surface measurements. Measurement results show that antenna surface figure and adjustments and electromagnetic patterns agree well with predictions.

Schroeder, Lyle C.↗

DOE OSTI2021

Mechanical behavior of additively manufactured and wrought 316L stainless steels before and after neutron irradiation

Fabrication of nuclear reactor components using additive manufacturing (AM) methods is now a practical option since the AM technologies have advanced to allow for building of complex parts with high quality materials. To assess the mechanical performance of printed components in reactor-relevant conditions and to build a property database for the AM 316L stainless steel (SS), mechanical testing and characterization were performed before and after neutron irradiation. In this work, miniature tensile specimens were irradiated at the High Flux Isotope Reactor (HFIR) to 0.2 and 2 displacements per atom (dpa) at 300 and 600°C. The AM 316L SS was tested in the as-built, stress-relieved, and solution-annealed conditions, and the wrought (WT) 316L SS in solution-annealed condition as a reference alloy. The baseline test result showed that the AM 316L SS, regardless of the post-build heat treatment, had higher strength than the WT 316L SS, but similar ductility. Post-irradiation tensile testing was conducted at RT, 300°C, and 500°C for selected irradiation conditions. Neutron irradiation induced significant changes in the mechanical behavior of the AM stainless steels, including both hardening and softening. Although the as-built 316L steel after 300°C irradiation showed necking just after yielding, the overall property changes of the as-printed alloy became less significant after 600°C irradiation. Irradiation-induced ductilization was also observed after the higher temperature irradiation. In general, the strength change was smaller in the relatively stronger as-built and stress-relieved AM SSs than in the solution-annealed AM and WT SSs. These relatively lower strength 316L SSs overall retained higher ductility in the irradiation conditions tested, but the stronger 316L SSs demonstrated a similar level of ductility after the higher temperature (600°C) irradiation. It is a positive assessment for the AM 316L materials that no embrittlement was observed within the test and irradiation conditions of the experiment.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Integrated process-structure–property–performance optimization of cold-sprayed zinc coatings on AZ91 magnesium alloy

High-pressure die cast (HPDC) AZ91 magnesium alloy is widely used in automotive components such as transmission housings and brackets for its excellent strength-to-weight ratio. Zinc-based cold spray coatings can be applied selectively to vulnerable areas to enhance corrosion resistance, minimize galvanic coupling with dissimilar metals, and eliminate the need for full-surface oxide coatings, making the process more efficient and targeted. A comprehensive evaluation of 16 combinations of nitrogen carrier gas temperatures and pressures led to the identification of an optimal range of process parameters, yielding Zn coatings with porosity <0.5 % by area, wear rates reduced by a factor of two compared to uncoated AZ91, and adhesion strengths up to 35 MPa. The enhanced mechanical performance of the coating is attributed to the low porosity and the formation of a metallurgical bond at the coating-substrate interface. Corrosion studies using macroscale potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) revealed a significant decrease in corrosion rate and a shift to more noble corrosion potentials (ZCP) for coated substrates. Furthermore, the Zn cold-sprayed samples exhibited significantly lower corrosion-induced evolved hydrogen content compared to the base AZ91 substrate and AZ91 coated with industrial coatings, demonstrating that the Zn layer effectively protects the substrate from the corrosive environment. Overall, cold spray Zn coatings significantly improve the mechanical and corrosion performance of AZ91 Mg alloys, addressing key material challenges and enabling their broader use in automotive applications.

Corrosion performance↗

NASA NTRS1992

Novel matrix resins for composites for aircraft primary structures, phase 1

The objective of the contract is the development of matrix resins with improved processability and properties for composites for primarily aircraft structures. To this end, several resins/systems were identified for subsonic and supersonic applications. For subsonic aircraft, a series of epoxy resins suitable for RTM and powder prepreg was shown to give composites with about 40 ksi compressive strength after impact (CAI) and 200 F/wet mechanical performance. For supersonic applications, a thermoplastic toughened cyanate prepreg system has demonstrated excellent resistance to heat aging at 360 F for 4000 hours, 40 ksi CAI and useful mechanical properties at greater than or equal to 310 F. An AB-BCB-maleimide resin was identified as a leading candidate for the HSCT. Composite panels fabricated by RTM show CAI of approximately 50 ksi, 350 F/wet performance and excellent retention of mechanical properties after aging at 400 F for 4000 hours.

Woo, Edmund P.↗

DOE OSTI2021

Statistical analysis of spatial distribution of pores in metal additive manufacturing

We report mechanical properties of additively manufactured parts are sensitive to the presence of pores form during the manufacturing process. The impact of pores on the mechanical performance has been investigated extensively with respect to different parameters, such as pore volume fraction, shape, and size. However, statistical investigations focusing on the relationships between the spatial distribution of pores and process parameters; and consequently, the performance of the manufactured parts are scattered and limited. Also, these sparse investigations usually suffer from an ambiguous definition of terminologies. For instance, the required criteria to consider a point pattern as complete spatial randomness (CSR) are generally not clarified. Moreover, no numerical formalism is yet developed to show how much the observed spatial results are statistically significant. To address these shortcomings, the statistical definition of CSR in a point pattern and the procedure to quantitatively determine the deviation of a pattern from CSR were discussed. The explained statistical approach was used to investigate the effect of scanning speed parameter on the spatial distribution of gas pores in laser powder bed fusion manufactured stainless steel parts. Furthermore, and to highlight the impact of the spatial distribution of pores on mechanical properties, fatigue performances of parts with clustered and randomly distributed pores were simulated by finite element analysis. It is shown that by reducing the scanning speed, the spatial distribution of gas pores deviated more from CSR, and correspondingly fatigue performance deteriorated.

36 MATERIALS SCIENCE↗

NASA NTRS2001

Phenylethynyl Terminated Arylene Ether Oxadiazole and Triazole Oligomers and Their Cured Polymers

Several novel phenylethynyl terminated arylene ether oligomers containing oxadiazole and triazole rings were prepared as part of an effort to develop high performance polymers with an attractive combination of properties (e.g. processability and mechanical performance) for future NASA applications. The oligomers displayed low melt viscosities and good solubilities. Thin films cast from solutions of the oligomers and cured for one hour at 350 C in air gave good tensile properties. Titanium to titanium (6Al-4V) tensile shear specimens were readily fabricated and provided moderate strengths. The chemistry and properties of these new materials are discussed.

Thompson, C. M.↗

DOE OSTI2022

Impact of Gold Thickness on Interfacial Evolution and Subsequent Embrittlement of Tin–Lead Solder Joints

Although gold remains a preferred surface finish for components used in high-reliability electronics, rapid developments in this area have left a gap in the fundamental understanding of solder joint gold (Au) embrittlement. Furthermore, as electronic designs scale down in size, the effect of Au content is not well understood on increasingly smaller solder interconnections. As a result, previous findings may have limited applicability. The current study focused on addressing these gaps by investigating the interfacial microstructure that evolves in 63Sn-37Pb solder joints as a function of Au layer thickness. Those findings were correlated to the mechanical performance of the solder joints. Increasing the initial Au concentration decreased the mechanical strength of a joint, but only to a limited degree. Kirkendall voids were the primary contributor to low-strength joints, while brittle fracture within the intermetallic compounds (IMC) layers is less of a factor. The Au embrittlement mechanism appears to be self-limiting, but only once mechanical integrity is degraded. Sufficient void evolution prevents continued diffusion from the remaining Au.

36 MATERIALS SCIENCE↗