Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Effect of Ce addition on the microstructure and properties of Al-Cu-Mn-Mg-Fe lithium battery shell alloy

Highlights: • Al{sub 6}(Mn, Fe) particles could be remarkably refined by Ce alloying. • Ce addition to the alloy promoted precipitation of S' phase. • Ce-containing alloy had higher tensile strength than that of Ce-free alloy. • Ce-containing alloy had positive corrosion potential and lower corrosion current density. - Abstract: Effect of Ce addition on the microstructures, mechanical properties and electrochemical properties of Al-Cu-Mn-Mg-Fe lithium battery alloy was investigated by optical microscope (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), tensile testing and electrochemical testing. Experimental results indicate that Ce addition resulted in the formation of Al{sub 8}Cu{sub 4}Ce phase in the Al-Cu-Mn-Mg-Fe alloy. The Ce-containing precipitates nucleated and grew up along the surface of Al{sub 6}(Mn, Fe) precipitates. Al{sub 6}(Mn, Fe) precipitates could be remarkably refined by Ce alloying. The aging precipitation behavior of S' phases could be promoted after Ce addition to the alloy. In comparison with Ce-free alloy, the Ce-containing alloy had higher tensile strength at both low temperature and elevated temperature. Especially at 200 °C, the yield strength and tensile strength of Ce-containing alloy substantially increased by 23.4% and 27.08%, respectively. Potentiodynamic polarization testing indicated that the Ce-containing alloy had a more positive corrosion potential and a lower corrosion current density.

36 MATERIALS SCIENCE↗

Computational Tools for Additive Manufacture of Tailored Microstructure and Properties

Additive manufacturing has the potential to revolutionize industrial hardware and unlock efficiency gains through the fabrication of geometries and architectures not possible by conventional processing. Currently most additive builds use a single set of process parameters (e.g. laser power and scan speed) which results in a part with a homogenous microstructure that provides a singular performance level. To move beyond this state, Raytheon Technologies Research Center worked to create a set of computational tools to track material evolution through each step of the additive process. Computational fluid dynamics and phase field models for microstructure evolution as a function of processing parameters, and crystal plasticity models fully coupling microstructure and mechanical properties for performance predictions were leveraged to establish a connection between additive parameters and the final microstructure. This framework was utilized to tailor spatially-varying mechanical properties in a part by appropriately controlling the microstructure evolution during the additive process. Specifically, a turbine blade was 3D printed from nickel superalloy IN718 using laser powder bed fusion with coarse grains in the airfoil section which experiences the highest temperatures and is creep limited while finer grains were printed in the root of the blade which experience higher stresses but at lower temperatures and is therefore fatigue limited. The benefit of being able to intentionally insert coarse grains in the high temperature region of the blade was showcased with a microstructure sensitive creep model that indicates longer creep life for coarser grains.

20 FOSSIL-FUELED POWER PLANTS↗

Temperature and time effects of post-weld heat treatments on tensile properties and microstructure of Zircaloy-4

Opportunities exist to expand the application of Zircaloy-4 (Zry-4) into lower-temperature (<100°C) applications. Welded areas within these structures are potential failure points and post-weld heat treatments (PWHTs) are not yet standardized for application in this temperature range. Zry-4 tungsten inert gas (TIG) welds were given PWHTs from 450-900°C with hold times from 0.5-48 hours to investigate changes to tensile properties and microstructure. Treatment of 800°C for 1 hour was found to produce the most ductile material, measured by total elongation of the tensile bar (16.5%). Furthermore, both PWHT time and temperature were observed to increase total elongation, except in extreme (>800°C or >18hours) cases, but the effect of temperature was stronger. The second order cumulative annealing parameter shows a trend with tensile properties. Average grain sizes in the fusion zone and heat affected zone did not change under any of the PWHTs until the development of an undesirable blocky-alpha phase, which was only observed to form in the heat affected zones for hold times greater than 18hr at 800°C.

36 MATERIALS SCIENCE↗

Chapter 4 - Research Tools: Microstructure, Mechanical Properties, and Computational Thermodynamics

The purpose of this Chapter is to provide an overview of the research tools that are available to evaluate the response of materials that are subject to atomic displacements caused by fast particle irradiation. The major focus is on metals employed in structural components in operating or planned nuclear fission and fusion reactors. Understanding, predicting and characterising the changes in material properties under irradiation requires the ability to characterise the irradiation-induced microstructure at and above the atomic scale, and the ability to relate such changes to the observed degradation in performance sustaining properties. Thus, any discussion of research tools necessarily involves microstructural characterization techniques and mechanical property characterization techniques. In addition, computational thermodynamics (and related multiscale, multiphysics modeling) can also be considered characterization tools since they enable the study of the thermodynamically and kinetically mediated mechanisms (influenced by the irradiation environment) that affect microstructural evolution. Hence, this chapter also contains a brief review of computational thermodynamics.

English, Colin A.↗

Effects of Sn addition on the microstructure, mechanical properties and corrosion behavior of Ti–Nb–Sn alloys

Ti and Ti alloys are widely used in restorative surgery because of their good biocompatibility, enhanced mechanical behavior and high corrosion resistance in physiological media. The corrosion resistance of Ti-based materials is due to the spontaneous formation of the TiO{sub 2} oxide film on their surface, which exhibits elevated stability in biological fluids. Ti–Nb alloys, depending on the composition and the processing routes to which the alloys are subjected, have high mechanical strength combined with low elastic modulus. The addition of Sn to Ti–Nb alloys allows the phase transformations to be controlled, particularly the precipitation of ω phase. The aim of this study is to discuss the microstructure, mechanical properties and corrosion behavior of cast Ti–Nb alloys to which Sn has been added. Samples were centrifugally cast in a copper mold, and the microstructure was characterized using optical microscopy, scanning electron microscopy and X-ray diffractometry. Mechanical behavior evaluation was performed using Berkovich nanoindentation, Vickers hardness and compression tests. The corrosion behavior was evaluated in Ringer's solution at room temperature using electrochemical techniques. The results obtained suggested that the physical, mechanical and chemical behaviors of the Ti–Nb–Sn alloys are directly dependent on the Sn content. - Graphical abstract: Effects of Sn addition to the Ti–30Nb alloy on the elastic modulus. - Highlights: • Sn addition causes reduction of the ω phase precipitation. • Minimum Vickers hardness and elastic modulus occurred for 6 wt.% Sn content. • Addition of 6 wt.% Sn resulted in maximum ductility and minimum compression strength. • All Ti–30Nb–XSn (X = 0, 2, 4, 6, 8 and 10%) alloys are passive in Ringer's solution. • Highest corrosion resistance was observed for 6 wt.% Sn content.

36 MATERIALS SCIENCE↗

The effect of carbon on the microstructures, mechanical properties, and deformation mechanisms of thermo-mechanically treated Fe 40.4 Ni 11.3 Mn 34.8 Al 7.5 Cr 6 high entropy alloys

We investigated the effects of cold rolling followed by annealing on the mechanical properties and dislocation substructure evolution of undoped and 1.1 at. % carbon-doped Fe 40.4 Ni 11.3 Mn 34.8 Al 7.5 Cr 6 high entropy alloys (HEAs). X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atom probe tomography (APT) were employed to characterize the microstructures. The as-cast HEAs were coarse-grained and single phase f.c.c., whereas the thermo-mechanical treatment caused recrystallization (to fine grain sizes) and precipitation (a B2 phase for the undoped HEA; and a B2 phase, and M 23 C 6 and M 7 C 3 carbides for the C-doped HEA). Carbon, which was found to have segregated to the grain boundaries using APT, retarded recrystallization. The reduction in grain size resulted in a sharp increase in strength, while the precipitation, which produced only a small increase in strength, probably accounted for the small decrease in ductility for both undoped and C-doped HEAs. For both undoped and C-doped HEAs, the smaller grain-sized material initially exhibited higher strain hardening than the coarse-grained material but showed a much lower strain hardening at large tensile strains. Wavy slip in the undoped HEAs and planar slip in C-doped HEAs were found at the early stages of deformation irrespective of grain size. At higher strains, dislocation cell structures formed in the 19 μm grain-sized undoped HEA, while microbands formed in the 23 μm grain-sized C-doped HEA. Conversely, localized dislocation clusters were found in both HEAs at the finest grain sizes (5 μm). The inhibition of grain subdivision by the grain boundaries and precipitates lead to the transformation from regular dislocation configurations consisting of dislocation-cells and microbands to irregular dislocation configurations consisting of localized dislocation clusters, which further account for the decrease in ductility. Our investigation of the formation mechanism and strain hardening of dislocation cells and microbands could benefit future structural material design.

36 MATERIALS SCIENCE↗

Mechanical Properties and Microstructure of High-Strength Steel Controlled by Hot Stamping Process

A novel design and manufacturing method, dubbed “precast,” of the cooling system and tools for a hot forming process was proposed in this paper. The integrated structures of the punch and blank holder were determined by analyzing the bending and reverse-bending deformation of the forming parts. The desired crashworthiness performance of an automotive front bumper constructed with this process was obtained by a tailored phase transformation, which generated martensite-bainite in the middle and full martensite transformation in the corner areas. Varying cooling effects in the formed parts caused the highest temperature to be located in the bottom and the lowest on the end of the formed parts. Moreover, the microstructural distributions demonstrated that the bottom possessed a relatively lower content of martensite, while, conversely, the end possessed a higher content. This was precisely the most desired phase distributions for the hot formed parts. For the six-process cycle stamping, the temperatures reached a stable status after an initial rapid increase in the first three process cycles. The microstructural results verified the feasibility of the hot forming tools under multiprocess cycles.

36 MATERIALS SCIENCE↗

Mechanical property and microstructure evolution of nitrogen-modified Ti-6Al-4V alloy with core-shell structure by hot compression

Highlights: • Core-shell structured Ti-6Al-4 V is composed of α shells and α + β cores. • Nitrogen solution and core-shell structure significantly enhances the strength. • Core-shell structural alloy performs inhomogeneous deformation. - Abstract: Core-shell (CS) structured Ti-6Al-4 V (Ti64) alloy with single α shells and duplex α + β cores was fabricated by powder nitriding and spark plasma sintering. The mechanical property and microstructure evolution of CS-Ti64 alloy was investigated by compression at temperatures of 950–1100 °C and strain rates of 0.001–1 s{sup −1}. The nitrogen-induced solid solution strengthening and the nitrogen-stabilized CS structure significantly enhanced the compressive strength. Microstructure evolution of CS-Ti64, involved inhomogeneous deformation of the core and shell, which was quite different from that of the commercial Ti64. Regions adjacent to shells and central locations of cores suffered large strain and therefore preferentially underwent dynamic recrystallization (DRX). The deformation mechanism of the novel CS-Ti64 alloy was discussed in terms of the α shells, α laths and DRX.

36 MATERIALS SCIENCE↗

Influence of Indium on Microstructure and Properties of Sn-Pb Binary Alloy Applied in Photovoltaic Ribbon

In this work, the conductivity, melting point, microstructure, spreading behavior, and mechanical properties of three types of Sn-Pb-In(indium) alloys are investigated along with Sn60Pb40 alloy as a reference. The results show that the In element improves the comprehensive properties of the Sn-Pb alloys. The maximum conductivity of the Sn-Pb-In alloys is 7.08 MS/m when the content of the In element is 3 wt.%. With an increasing content of the In element, the melting points of the Sn-Pb-In alloys gradually decrease from 183 to 166 °C. The microstructures of the alloys are refined with the addition of In. The intermetallic compound (IMC) InSn{sub 4} is only found in Sn60Pb34In6, except for the α-Pb and β-Sn phases. A spread test shows that only IMC Cu{sub 6}Sn{sub 5} is present at the Cu/solder interface of the solder joints. The Sn60Pb34In3 solder joint shows the highest ultimate tensile strength of 54 MPa. The microhardness of the alloys slightly increases from 12.76 HV{sub 0.05} to 13.56 HV{sub 0.05} with the In content increasing from 0 to 3 wt.%, while a sharp increase to 15.53 HV{sub 0.05} is observed when the amount of In exceeds 3 wt.%.

36 MATERIALS SCIENCE↗

High-Speed Friction Stir Welding of AA7075-T6 Sheet: Microstructure, Mechanical Properties, Micro-texture, and Thermal History

Friction-stir-welding (FSW) is a cost-effective and high quality joining process for aluminum alloys (especially heat-treatable allo ys) that has been applied successfully in the aerospace industry. However, the full potential of FSW on more cost-sensitive applications is still limited by the production rate, namely the welding speed of the process. The majority of literature evaluating FSW of aluminum alloys is based on welds made in the range of welding speeds around hundreds of millimeters per minute, and only a handful are at a moderate speed of 1 m/min. In this study we present a microstructural analysis of friction stir welded AA7075-T6 blanks with welding speeds up to 3 m/min. Textures, microstructures, mechanical properties, and weld quality are analyzed using TEM, EBSD, metallographic imaging, and Vickers hardness. Results are coupled with welding parameters to aid in the understanding of the complex material flow and texture gradients within the welds in an effort to optimize welding parameters for high speed processing.

Zhang, Jingyi↗

Microstructure, compression properties, and oxidation behavior of Hf-25Ta-5Me alloys (Me is Mo, Nb, W, 0.5Mo + 0.5 W, Cr, or Zr)

Hf–Ta based alloys have recently been investigated as potential candidates for high-temperature structural applications. While most attentions have been given to the properties above ~1200 °C where the alloys are mainly single-phase BCC structures and have excellent oxidation performance due to formation of super-oxides, structural properties at lower temperatures are equally important for applications in which an alloy may experience a range of temperatures. In the present work, microstructure, phase composition, mechanical properties and oxidation behavior of six Hf-25Ta-5Me alloys (Me is Mo (HTM alloy), W (HTW), 0.5Mo + 0.5 W (HTMW), Cr (HTC) or Zr (HTZ), the compositions are in at.%) are reported at temperatures below the eutectoid transformation. The alloys were prepared by arc melting followed by hot isostatic pressing for 3 h at 1400 °C and 207 MPa. All the alloys display coarse grains of partially or fully transformed (by a eutectoid reaction) high-temperature BCC phase. The eutectoid regions consist of fine lamellae of Hf-rich HCP and Ta-rich BCC phases. The ternary alloys containing W or Cr also contained small amounts of a cubic Laves phase. At 25 °C, the HTW alloy was the strongest (yield stress σ y = 1966 MPa) but brittle and HTZ was the weakest (σ y = 1120 MPa) but ductile among the studied alloys. Other alloys showed intermediate behaviors. In general, the room temperature ductility of the alloys increased with decreasing σy. All alloys maintained high strength up to 800 °C, but displayed a noticeable strength decrease at 1000 °C. At 1000 °C, HTMW was the strongest alloy (σ y = 468 MPa) and HTC was the weakest alloy (σ y = 368 MPa). All alloys had excellent deformability at 1000 °C. Oxidation behavior of the alloys was studied at 800 °C and 1000 °C and compared with that of Hf–27Ta binary alloy. Although the ternary additions improved oxidation resistance, overall oxidation performance of the studied alloys at 800 °C and 1000 °C was poor.

36 MATERIALS SCIENCE↗

Mechanical Properties and Microstructure of Plasma Sprayed Ni-Based Metallic Glass Coating

Various developmental research works on the metallic glass have been conducted in order to broaden its application field. Thermal spraying method is one of the potential techniques to enhance the excellent properties such as high toughness and corrosion resistance of the metallic glass material. The gas tunnel type plasma spraying is useful to obtain high quality ceramic coatings such as Al{sub 2}O{sub 3} and ZrO{sub 2} coatings. In this study, the Ni-based metallic glass coatings were produced by the gas tunnel type plasma spraying under various experimental conditions, and their microstructure and mechanical properties were investigated. At the plasma current of 200-300 A, the Ni-based metallic glass coatings of more than 200 {mu}m in thickness were formed densely with Vickers hardness of about Hv = 600.

36 MATERIALS SCIENCE↗

The effect of postprocessing on tensile property and microstructure evolution of friction stir welding aluminum alloy joint

Friction stir welding is an efficient manufacturing method for joining aluminum alloy and can dramatically reduce grain size conferring excellent plastic deformation properties. Consequently, friction stir welding is used to manufacture tailor welded blanks to optimize weight or performance in the final component. In the study, the microstructural evolution and mechanical properties of friction stir welding joint during plastic forming and subsequent heat treatment were investigated. The microstructural characteristics of the friction stir welding joints were studied by Electron Backscattered Diffraction and Transmission Electron Microscopy. The mechanical properties were evaluated by tensile and microhardness tests. It is found that the tensile and yield strengths of friction stir welding joints are significantly improved after severe plastic deformation due to the grain refinement. Following heat treatment, the strength of the friction stir welding joints significantly decrease due to the obvious abnormal grain growth. Careful attention must be given to the processing route of any friction stir welding joint intended for plastic forming, especially the annealing between forming passes. Severe plastic deforming of the friction stir welding joint leads to a high level of stored energy/dislocation density, which causes the abnormal grain growth during subsequent heat treatment, and consequently reduce the mechanical properties of the friction stir welding joint. - Highlights: • Great changes are observed in the microstructure of FSW joint after postprocessing. • Postprocessing shows great effect on the microstructure stability of FSW joint. • The weld shows more significant decrease in strength than the BM due to the AGG. • Attention must be given to the processing route of FSW joint for plastic forming.

36 MATERIALS SCIENCE↗

Microstructure, Mechanical Properties and Residual Stress of Selective Laser Melted AlSi10Mg

AlSi10Mg processed by selective laser melting (SLM) is common in various industries because of its complex structure and high performance. The microstructure, residual stress and mechanical properties restrict its application, while they are affected by the scanning path type and preheating temperature. In this work, to investigate the properties of selective laser melted AlSi10Mg alloys and gain better performance results, the microstructure and mechanical tests are performed at several preheating temperatures based on the uniformity and chessboard scanning strategy. It is found that the selective laser melted AlSi10Mg parts fabricated in the chessboard scanning path have better mechanical properties than those fabricated in the uniformity scanning path. Furthermore, a higher preheating temperature can induce less residual stress due to the enhanced Al crystal faces. Finally, analyses of the microstructures, mechanical and residual stress provide a valuable suggestion that the combination of the range of preheating temperature and the scanning path can improve the performance of selective laser melted AlSi10Mg.

36 MATERIALS SCIENCE↗

Microstructure and properties of a high temperature Al–Ce–Mn alloy produced by additive manufacturing

An Al–10Ce-8Mn (wt%) alloy was designed and fabricated by laser powder bed fusion additive manufacturing (AM). The rapid cooling rates of the AM process produced a refined microstructure with a large fraction of reinforcing intermetallic phases. The tensile properties of the alloy were characterized in the as-fabricated state and following thermal exposure. The properties of the as-fabricated microstructure showed exceptional high-temperature performance and strength retention at elevated temperatures up to 400 °C relative to benchmark wrought Al and AM Al alloy properties. Characterization of the microstructure and thermodynamic modeling of the ternary Al–Ce–Mn system rationalized the solidification and solid-state phase transformations. Finally, analysis of the relevant strengthening mechanisms for both the as-fabricated and thermally exposed conditions was performed.

36 MATERIALS SCIENCE↗

Effect of Solution Treatment on the Microstructure, Micromechanical Properties, and Kinetic Parameters of the β → α Phase Transformation during Continuous Cooling of Ti-6Al-4V Titanium Alloy

The aim of this study is to examine the effect of solution treatment temperature (STT) on the microstructure, the micromechanical properties, and the kinetic parameters of the β → α phase transformation during continuous cooling of the dual phase titanium alloy Ti-6Al-4V. Increasing the STT from 1050 to 1200 °C delays the formation of the α phase during cooling and increases the value of its activation energy. The microstructural analysis reveals the emergence of α{sub W} platelets from protuberances on the α{sub GB}/α{sub W} interface. The investigation of the morphology of the α{sub W} platelets reveals the presence of ledges on their longest side showing a sharp extremity. The micromechanical properties determined by nanoindentation and microhardness tests are almost insensitive to the cooling rate but are strongly affected by the STT; the higher the STT, the lower the overall microhardness of the Ti-6Al-4V alloy. In addition, the STT affects the microhardness and the Young’s modulus of both α and β phases differently; when the STT increases, the microhardness and the Young’s modulus of the α phase decrease, whereas those of the β phase increases.

36 MATERIALS SCIENCE↗

Effect of Nb micro-alloying on microstructure and properties of thermo-mechanically processed high carbon pearlitic steel

Highlights: • Effect of Nb micro-alloying on high carbon steels has been established. • Fine and degenerated pearlite with fine PAGS is achieved due to Nb micro-alloying. • AFM study indicates true interlamellar spacing which conforms well to TEM study. • Hardness and yield strength have been obviously improved with the addition of Nb. - Abstract: Two C-Mn-Si steels with and without Nb micro-alloying are selected in the present study. Both these high carbon steels have been thermo-mechanically processed using Gleeble 3800 simulator. Optical microscope (OM), scanning electron microscope (SEM), transmission electron microscope (TEM), atomic force microscope (AFM) were utilised for microstructural characterisation. The austenitising temperature was varied from 1150 °C to 1200 °C followed by hot compression and subjected to free cooling to evaluate the influence of austenite grain size on transformed microstructure and mechanical properties. It is evident that higher austenite grain size is obtained for both types of steels subjected to higher austenitising temperature. The refinement of pearlite interlamellar spacing (<0.20 μm) with degenerated morphology as well as finer prior austenite grain size (<40 μm) is found to be more prominent for Nb micro-alloyed sample. The average hardness values of both the steels are higher for the specimens, treated at a higher austenitising temperature which is attributed to finer interlamellar spacing. Finally, the correlation between the evolving microstructure and resulting mechanical properties (hardness and yield strength) has been made.

36 MATERIALS SCIENCE↗

Predicting melt pool depth and grain length using multiple signatures from in-situ single camera two-wavelength imaging pyrometry for laser powder bed fusion

In laser powder bed fusion (LPBF), the in-situ process signatures are known to have a direct correlation with the microstructural properties of the solidified melt pool (MP). It is known that the MP cooling and heating rates, and laser processing parameters can critically determine the grain structure and thereby affect the part properties. The objective of this work is to study the feasibility of using in-process, high-speed imaging pyrometry for evaluating the solidified MP properties “below” the surface, such as depth and microstructural properties. To accomplish this, we employ an in-house single camera-based two-wavelength imaging pyrometry (STWIP) system for monitoring the printing of single-scan tracks with Inconel 718 on a commercial LPBF printer (EOS M290). Further, the lab designed STWIP system is a coaxial high-speed (>10,000 fps) imaging system capable of monitoring MP temperature, morphology, and intensity profiles. The temperature measurements from STWIP are emissivity independent. The STWIP measured MP signatures of the printed tracks are correlated with the ex-situ microscopy characterized MP depth and the average grain lengths. From the data analysis, using support vector machine (SVM)-based regression models, we found that the MP temperature signatures are crucial for an accurate prediction of MP depth and the grain length, thus validating the novelty and necessity of the developed in-situ monitoring methods and analysis.

36 MATERIALS SCIENCE↗