Search NASA⌕ Search

SEARCH · Search NASA

Results for “negative capacitance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Effects of sodium ions on trapping and transport of electrons at the SiO{sub 2}/4H-SiC interface

Capacitance-voltage (C-V) and Deep-Level-Transient Spectroscopy (DLTS) measurements were performed on Metal-Oxide-Semiconductor (MOS) capacitors fabricated on 4H-SiC with the SiO{sub 2} layer grown by Sodium-Enhanced Oxidation. This technique has yielded 4H-SiC MOS transistors with record channel mobility, although with poor bias stability. The effects of the mobile positive charge on the C-V characteristics and DLTS spectra were investigated by applying a sequence of positive and negative bias-temperature stresses, which drifted the sodium ions toward and away from the SiO{sub 2}/4H-SiC interface, respectively. Analytical modeling of the C-V curves shows that the drift of sodium ions in the SiO{sub 2} layer during the voltage sweep can explain the temperature dependence of the C-V curves. The effects of lateral fluctuations of the surface potential (due to a non-uniform charge distribution) on the inversion layer mobility of MOS transistors are discussed within a two-dimensional percolation model.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dielectric response of tantalum oxide subject to induced ion bombardment during oblique sputter deposition

We describe the deposition of insulating tantalum oxide thin films under conditions of controlled ion bombardment, which can be achieved using reactive sputtering on 90 deg. off-axis substrates with an applied substrate bias. Capacitive measurements of Ta{sub 2}O{sub 5} deposited on unbiased off-axis substrates indicate low frequency dielectric constants as high as epsilon{sub r}approx300. Low frequency loss tangents are high, tan delta>0.5, and have a pronounced frequency dependence. Deposition of the film off-axis with sufficient applied rf bias to the substrate (negative bias >-70 V) recovers the on-axis properties typical of Ta{sub 2}O{sub 5}, e.g., epsilon{sub r}approx22 and tan deltaapprox0.02. The recovery of normal dielectric behavior is attributed to the ion bombardment of the growing film under substrate bias, similar to on-axis depositions but absent from depositions on off-axis substrates with no applied substrate bias. We suggest that insufficiently bombarded films develop a Maxwell-Wagner type polarization along columnar voids. The void structure and the associated dielectric response vary with distance from the sputtering source due to variations in ion density and angle from the sputtering source. A similar dielectric response is observed in depositions on on-axis substrates as a function of angle from the central sputter gun axis. Our results suggest that ion bombardment is necessary for good quality sputtered dielectric films but that a controlled Ar{sup +} flux is essentially equivalent to the uncontrolled O{sub 2}{sup -}/O{sup 2-} flux of on-axis reactive sputtering.

36 MATERIALS SCIENCE↗

Plasma-assisted atomic layer deposition of TiN/Al{sub 2}O{sub 3} stacks for metal-oxide-semiconductor capacitor applications

By employing plasma-assisted atomic layer deposition, thin films of Al{sub 2}O{sub 3} and TiN are subsequently deposited in a single reactor at a single substrate temperature with the objective of fabricating high-quality TiN/Al{sub 2}O{sub 3}/p-Si metal-oxide-semiconductor capacitors. Transmission electron microscopy and Rutherford backscattering spectroscopy analyses show well-defined interfaces and good Al{sub 2}O{sub 3} stoichiometry, respectively. Electrical investigation of as-deposited test structures demonstrates leakage current densities as low as approx1 nA/cm{sup 2}. Current-voltage (I-V) measurements demonstrate clear Fowler-Nordheim tunneling with an average TiN/Al{sub 2}O{sub 3} barrier height of 3.3 eV. Steep Weibull distributions of the breakdown electric field around 7.5 MV/cm indicate good reliability of these devices. Time-dependent dielectric breakdown measurements demonstrate that the devices can sustain high operating electric fields of 3-4 MV/cm for the 10 year lifetime criterion. From capacitance-voltage (C-V) measurements, a dielectric constant (k) of 8.7+-0.1 was extracted for the Al{sub 2}O{sub 3}. No direct dependence on the deposition temperature was found in the range 350-400 deg. C, although the stack deposited at 400 deg. C demonstrates significantly lower C-V hysteresis of approx50 mV. A negative fixed oxide charge density of (9.6+-0.2)x10{sup 12} cm{sup -2} was found to be present at the Al{sub 2}O{sub 3}/p-Si interface.

36 MATERIALS SCIENCE↗

Electron energy distribution functions measured by Langmuir probe with optical emission spectroscopy in very high frequency capacitive discharge in nitrogen

By using a rf compensated Langmuir probe and optical emission spectroscopy, the effects of driving frequency (13.56-50 MHz) on the electron energy probability function (EEPF), electron density, electron temperature, and the vibrational and rotational temperatures in capacitively coupled nitrogen discharge were investigated. Measurements were performed in the pressure range 60-200 mTorr, and at a fixed voltage of 140 V (peak-to-peak). With increasing the driving frequency, the dissipated power and electron density markedly increased along with the intensity of the optical emission lines belonging to the 2nd positive (337.1 nm) and 1st negative systems (391.4 nm) of N{sub 2}. The EEPF at low pressure 60 mTorr is two-temperature (bi-Maxwellian) distribution, irrespective of the driving frequency, in contrast with argon and helium discharges in the similar conditions. The mechanism forming such bi-Maxwellian shape was explained by two combined effects: one is the collisionless sheath-heating effect enhancing the tail electron population, and the other is the collision-induced reduction of electrons at the energy 2-4 eV where the collision cross-section for the vibrational excitation has a resonantly large peak. The two-temperature EEPF structure was basically retained at moderate pressure 120 mTorr and high pressure 200 mTorr. The vibrational temperature T{sub vib} and rotational temperature T{sub rot} are measured for the sequence ({Delta}{nu}=-2) of N{sub 2} second positive system (C{sup 3}{Pi}{sub u}{yields}B{sup 3}{Pi}{sub g}) using the method of comparing the measured and calculated spectra with a chi-squared minimization procedure. It was found that, both of T{sub vib} and T{sub rot} are a weakly dependent on driving frequency at low pressure 60 mTorr. At higher pressure (120 and 200 mTorr), T{sub vib} rises monotonically with the driving frequency, whereas the T{sub rot} slightly decreases with frequency below 37 MHz, beyond which it relatively increases or saturated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Characterization of interface states in Al{sub 2}O{sub 3}/AlGaN/GaN structures for improved performance of high-electron-mobility transistors

We have investigated the relationship between improved electrical properties of Al{sub 2}O{sub 3}/AlGaN/GaN metal-oxide-semiconductor high-electron-mobility transistors (MOS-HEMTs) and electronic state densities at the Al{sub 2}O{sub 3}/AlGaN interface evaluated from the same structures as the MOS-HEMTs. To evaluate Al{sub 2}O{sub 3}/AlGaN interface state densities of the MOS-HEMTs, two types of capacitance-voltage (C-V) measurement techniques were employed: the photo-assisted C-V measurement for the near-midgap states and the frequency dependent C-V characteristics for the states near the conduction-band edge. To reduce the interface states, an N{sub 2}O-radical treatment was applied to the AlGaN surface just prior to the deposition of the Al{sub 2}O{sub 3} insulator. As compared to the sample without the treatment, the N{sub 2}O-radical treated Al{sub 2}O{sub 3}/AlGaN/GaN structure showed smaller frequency dispersion of the C-V curves in the positive gate bias range. The state densities at the Al{sub 2}O{sub 3}/AlGaN interface were estimated to be 1 × 10{sup 12} cm{sup −2} eV{sup −1} or less around the midgap and 8 × 10{sup 12} cm{sup −2} eV{sup −1} near the conduction-band edge. In addition, we observed higher maximum drain current at the positive gate bias and suppressed threshold voltage instability under the negative gate bias stress even at 150 °C. Results presented in this paper indicated that the N{sub 2}O-radical treatment is effective both in reducing the interface states and improving the electrical properties of the Al{sub 2}O{sub 3}/AlGaN/GaN MOS-HEMTs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Capacitance and conductance versus voltage characterization of Al{sub 2}O{sub 3} layers prepared by plasma enhanced atomic layer deposition at 25 °C≤ T ≤ 200 °C

In this work, plasma enhanced atomic layer deposited (PE-ALD) samples were prepared at substrate temperatures in the range between room temperature (RT) and 200 °C and investigated by capacitance–voltage and conductance–voltage recordings. The measurements are compared to standard thermal atomic layer deposition (T-ALD) at 200 °C. Very low interface state density (D{sub it}) ∼10{sup 11} eV{sup −1} cm{sup −2} could be achieved for the PE-ALD process at 200 °C substrate temperature after postdeposition anneal (PDA) in forming gas at 450 °C. The PDA works very effectively for both the PE-ALD and T-ALD at 200 °C substrate temperature delivering also similar values of negative fixed charge density (N{sub fix}) around −2.5 × 10{sup 12} cm{sup −2}. At the substrate temperature of 150 °C, highest N{sub fix} (−2.9 × 10{sup 12} cm{sup −2}) and moderate D{sub it} (2.7 × 10{sup 11} eV{sup −1} cm{sup −2}) values were observed. The as deposited PE-ALD layer at RT shows both low D{sub it} in the range of (1 to 3) × 10{sup 11} eV{sup −1} cm{sup −2} and low N{sub fix} (−4.4 × 10{sup 11} cm{sup −2}) at the same time. The dependencies of N{sub fix}, D{sub it}, and relative permittivity on the substrate temperatures and its adjustability are discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Morphology and Crystallinity Effects of Nanochanneled Niobium Oxide Electrodes for Na-Ion Batteries

Niobium pentoxide (Nb 2 O 5 ) is a promising negative electrode for sodium ion batteries (SIBs). By engineering the morphology and crystallinity of nanochanneled niobium oxides (NCNOs) the kinetic behavior and charge storage mechanism of Nb 2 O 5 electrodes were investigated. Amorphous and crystalline NCNO samples were made by modulating anodization conditions (20 - 40V and 140 - 180 °C) to synthesize nanostructures of differing pore sizes and wall thicknesses with identical chemical composition. The electrochemical energy storage properties of the NCNOs were studied with the amorphous samples showing better overall rate performance than the crystalline samples. The enhanced rate performance of the amorphous samples is attributed to the higher capacitive contributions and Na-ion diffusivity analyzed from cyclic voltammetry (CV) and galvanostatic intermittent titration technique (GITT). It was found that the amorphous samples with smaller wall thicknesses facilitated improved kinetics. Among samples with similar pore size and wall thickness, the difference in their power performance stems from crystallinity effect, which plays a more significant role in the resulting kinetics of the materials for Na-ion batteries.

25 ENERGY STORAGE↗

Interfacial water asymmetry at ideal electrochemical interfaces

Controlling electrochemical reactivity requires a detailed understanding of the charging behavior and thermodynamics of the electrochemical interface. Experiments can independently probe the overall charge response of the electrochemical double layer by capacitance measurements and the thermodynamics of the inner layer with potential of maximum entropy measurements. Relating these properties by computational modeling of the electrochemical interface has so far been challenging due to the low accuracy of classical molecular dynamics (MD) for capacitance and the limited time and length scales of ab initio MD. Here, we combine large ensembles of long-time-scale classical MD simulations with charge response from electronic density functional theory to predict the potential-dependent capacitance of a family of ideal aqueous electrochemical interfaces with different peak capacitances. We show that while the potential of maximum capacitance varies, this entire family exhibits an electrode charge of maximum capacitance (CMC) between -2.9 and -2.2 μC/cm 2 , regardless of the details in the electronic response. Simulated heating of the same interfaces reveals that the entropy peaks at a charge of maximum entropy (CME) of -5.1 ± 0.6 μC/cm 2 , in agreement with experimental findings for metallic electrodes. The CME and CMC both indicate asymmetric response of interfacial water that is stronger for negatively charged electrodes, while the difference between CME and CMC illustrates the richness in behavior of even the ideal electrochemical interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding LIB Battery Electrodes Through Classical Electrochemical Interface Theory

Classical models of the electrochemical interface can be applied to complex and dynamic electrodes to understand important mechanisms that are relevant to device-level phenomena like calendar aging or cycle life. Here, we show that negative alloy electrodes with wide electrochemical windows cannot be assumed to have static interfaces throughout all states of charge. Under high states of charge, the interface -including the solid electrolyte interphase - has characteristics that resemble a highly polarized electrode far from the point of zero charge. Under these conditions, the interface can be understood through the Helmholtz model. At lower states of charge, the interface capacitance decreases and the space charge layer length increases. This transformation resembles a metal electrode approaching the point of zero charge which is understood through the Gouy-Chapman-Stern-Grahame model of the electrochemical interface. This transformation happens at both silicon and carbon-coated silicon interfaces. From voltage-limited cycling experiments, in the limit of the diffuse double layer, the silicon electrode impedance rises significantly in the first few cycles. This rise is related to the continuous electrochemical reduction of electrolyte components from an interface that is not electronically screened from the electrolyte. In other words, an electrode interface for batteries should resemble a 'Helmholtz-like' structure.

anode↗

Asymmetric Supercapacitor for Long-Duration Power Storage

A document discusses a project in which a series of novel hybrid positive electrode materials was developed and tested in asymmetric capacitors with carbon negative electrodes. The electrochemical performance of the hybrid capacitors was characterized by cyclic voltammetry and a DC charge/discharge test. The hybrid capacitor exhibited ideal capacitor behavior with an extended operating voltage of 1.6 V in aqueous electrolyte, and energy density higher than activated carbon-based supercapacitors. Nanostructured MnO2 is a promising material for electrochemical capacitors (ECS) because of its low cost, environmentally friendly nature, and reasonably high specific capacitance. The charge capacity of the capacitors can be further improved by increasing the specific surface area of the MnO2 electrode material. The power density and space radiation stability of the capacitors can be enhanced by coating the MnO2 nanoparticles with conducting polymers. The conducting polymer coating also helps in radiation-hardening the ECS.

Rangan, Krishnaswamy K.↗

Insulator Surface Flashover Due to UV Illumination

The surface of an insulator under vacuum and under electrical charge will flashover when illuminated by a critical dose of ultra-violet (UV) radiation - depending on the insulator size and material, insulator cone angle, the applied voltage and insulator shot-history. A testbed comprised of an excimer laser (KrF, 248 nm, {approx}16 MW, 30 ns FWHM,), a vacuum chamber, and a negative polarity dc high voltage power supply ({le} -60 kV) were assembled to test 1.0 cm thick angled insulators for surface-flashover. Several candidate insulator materials, e.g. High Density Polyethylene (HDPE), Rexolite{reg_sign} 1400, Macor{trademark} and Mycalex, of varying cone angles were tested against UV illumination. Commercial energy meters were used to measure the UV fluence of the pulsed laser beam. In-house designed and fabricated capacitive probes (D-dots, >12 GHz bandwidth) were embedded in the anode electrode underneath the insulator to determine the time of UV arrival and time of flashover. Of the tested insulators, the +45 degree Rexolite insulator showed more resistance to UV for surface flashover; at UV fluence level of less than 13 mJ/cm{sup 2}, it was not possible to induce a flashover for up to -60 kV of DC potential across the insulator's surface. The probes also permitted the electrical charge on the insulator before and after flashover to be inferred. Photon to electron conversion efficiency for the surface of Rexolite insulator was determined from charge-balance equation. In order to understand the physical mechanism leading to flashover, we further experimented with the +45 degree Rexolite insulator by masking portions of the UV beam to illuminate only a section of the insulator surface; (1) the half nearest the cathode and subsequently, (2) the half nearest the anode. The critical UV fluence and time to flashover were measured and the results in each case were then compared with the base case of full-beam illumination. It was discovered that the time for the insulator to flash was earlier in time for the cathode-half beam illumination case than the anode-half illumination case which led us to believe that the flashover mechanism for the UV illumination is initiated from the cathode side of the insulator. Qualitatively stated, the testing revealed that the shielding of the cathode triple point against UV is more important than the anode triple junction in the design of vacuum insulators and electrodes. The goal of this work was to acquire empirical data on critical UV fluence (energy per unit area) required to induce surface flashover of vacuum insulators for some candid insulator materials: High Density Polyethylene (HDPE), Rexolite{reg_sign} 1400, Macor{trademark} and Mycalex. This work was a clarification and extension of studies performed by C.L. Enloe, et. al. in the 80's [1-3]. Additionally, to gain an understanding of the physical mechanism of flashover, we experimented with UV illumination of a portion of the insulator's surface near the cathode and subsequently near the anode. The results of these experiments are covered in detail.

36 MATERIALS SCIENCE↗

Voltage linearity modulation and polarity dependent conduction in metal-insulator-metal capacitors with atomic-layer-deposited Al{sub 2}O{sub 3}/ZrO{sub 2}/SiO{sub 2} nano-stacks

Excellent voltage linearity of metal-insulator-metal (MIM) capacitors is highly required for next generation radio frequency integration circuits. In this work, employing atomic layer deposition technique, we demonstrated how the voltage linearity of MIM capacitors was modulated by adding different thickness of SiO{sub 2} layer to the nano-stack of Al{sub 2}O{sub 3}/ZrO{sub 2}. It was found that the quadratic voltage coefficient of capacitance (α) can be effectively reduced from 1279 to −75 ppm/V{sup 2} with increasing the thickness of SiO{sub 2} from zero to 4 nm, which is more powerful than increasing the thickness of ZrO{sub 2} in the Al{sub 2}O{sub 3}/ZrO{sub 2} stack. This is attributed to counteraction between the positive α for Al{sub 2}O{sub 3}/ZrO{sub 2} and the negative one for SiO{sub 2} in the MIM capacitors with Al{sub 2}O{sub 3}/ZrO{sub 2}/SiO{sub 2} stacks. Interestingly, voltage-polarity dependent conduction behaviors in the MIM capacitors were observed. For electron bottom-injection, the addition of SiO{sub 2} obviously suppressed the leakage current; however, it abnormally increased the leakage current for electron top-injection. These are ascribed to the co-existence of shallow and deep traps in ZrO{sub 2}, and the former is in favor of the field-assisted tunnelling conduction and the latter contributes to the trap-assisted tunnelling process. The above findings will be beneficial to device design and process optimization for high performance MIM capacitors.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Scaling of silicon nanoparticle growth in low temperature flowing plasmas

Low temperature plasmas are an emerging method to synthesize high quality nanoparticles (NPs). An established and successful technique to produce NPs is using a capacitively coupled plasma (CCP) in cylindrical geometry. Although a robust synthesis technique, optimizing or specifying NP properties using CCPs, is challenging. In this paper, results from a computational investigation for the growth of silicon NPs in flowing inductively coupled plasmas (ICPs) using Ar/SiH 4 gas mixtures of up to a few Torr are discussed. ICPs produce more locally constrained and quiescent plasma potentials. These positive plasma potentials produce an electrostatic trap for negatively charged NPs, which can significantly extend the residence time of NPs in the plasma, which in turn provides a controllable period for particle growth. The computational platforms used in this study consist of a two-dimensional plasma hydrodynamics model, a three-dimensional nanoparticle growth and trajectory tracking model, and a molecular dynamics simulation for deriving reactive sticking coefficients of silane radicals on Si NPs. Trends for the nanoparticle growth as a function of SiH 4 inlet fraction, gas residence time, energy deposition per particle, pressure, and reactor diameter are discussed. The general path for particle synthesis is the trapping of small NPs in the positive electrostatic potential, followed by entrainment in the gas flow upon reaching a critical particle size. Optimizing or controlling NP synthesis then depends on the spatial distribution of plasma potential, the density of growth species, and the relative time that particles spend in the electrostatic trap and flowing through higher densities of growth species upon leaving the trap.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Miniaturized magnet-less RF electron trap. II. Experimental verification

Atomic microsystems have the potential of providing extremely accurate measurements of timing and acceleration. But, atomic microsystems require active maintenance of ultrahigh vacuum in order to have reasonable operating lifetimes and are particularly sensitive to magnetic fields that are used to trap electrons in traditional sputter ion pumps. Our paper presents an approach to trapping electrons without the use of magnetic fields, using radio frequency (RF) fields established between two perforated electrodes. The challenges associated with this magnet-less approach, as well as the miniaturization of the structure, are addressed. These include, for example, the transfer of large voltage (100–200 V) RF power to capacitive loads presented by the structure. The electron trapping module (ETM) described here uses eight electrode elements to confine and measure electrons injected by an electron beam, within an active trap volume of 0.7 cm 3 . The operating RF frequency is 143.6 MHz, which is the measured series resonant frequency between the two RF electrodes. It was found experimentally that the steady state electrode potentials on electrodes near the trap became more negative after applying a range of RF power levels (up to 0.15 W through the ETM), indicating electron densities of ≈3 × 10 5 cm -3 near the walls of the trap. The observed results align well with predicted electron densities from analytical and numerical models. The peak electron density within the trap is estimated as ~1000 times the electron density in the electron beam as it exits the electron gun. Finally, this successful demonstration of the RF electron trapping concept addresses critical challenges in the development of miniaturized magnet-less ion pumps.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Negative charge trapping effects in Al{sub 2}O{sub 3} films grown by atomic layer deposition onto thermally oxidized 4H-SiC

This letter reports on the negative charge trapping in Al{sub 2}O{sub 3} thin films grown by atomic layer deposition onto oxidized silicon carbide (4H-SiC). The films exhibited a permittivity of 8.4, a breakdown field of 9.2 MV/cm and small hysteresis under moderate bias cycles. However, severe electron trapping inside the Al{sub 2}O{sub 3} film (1 × 10{sup 12} cm{sup −2}) occurs upon high positive bias stress (>10 V). Capacitance-voltage measurements at different temperatures and stress conditions have been used to determine an activation energy of 0.1 eV. The results provide indications on the possible nature of the trapping defects and, hence, on the strategies to improve this technology for 4H-SiC devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ionic Associations and Hydration in the Electrical Double Layer of Water-in-Salt Electrolytes

Water-in-Salt-Electrolytes (WiSEs) are an exciting class of concentrated electrolytes finding applications in energy storage devices because of their expanded electrochemical stability window, good conductivity and cation transference number, and fire-extinguishing properties. These distinct properties are thought to originate from the presence of an anion-dominated ionic network and interpenetrating water channels for cation transport, which indicates that associations in WiSEs are crucial to understanding their properties. Currently, associations have mainly been investigated in the bulk, while little attention has been given to the electrolyte structure near electrified interfaces. Here, we develop a theory for the electrical double layer (EDL) of WiSEs, where we consistently account for the thermoreversible associations of species into Cayley tree aggregates. The theory predicts an asymmetric structure of the EDL. At negative voltages, hydrated Li + dominates, and cluster aggregation is initially slightly enhanced before disintegration at larger voltages. At positive voltages, when compared to the bulk, clusters are strictly diminished. Performing atomistic molecular dynamics (MD) simulations of the EDL of WiSE provides EDL data for validation and bulk data for parametrization of our theory. Validating the predictions of our theory against MD showed good qualitative agreement. Furthermore, we performed electrochemical impedance measurements to determine the differential capacitance of the studied LiTFSI WiSE and also found reasonable agreement with our theory. Overall, the developed approach can be used to investigate ionic aggregation and solvation effects in the EDL, which, among other properties, can be used to understand the precursors for solid-electrolyte interphase formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Probing the In Situ Pseudocapacitive Charge Storage in Ti 3 C 2 MXene Thin Films with X-ray Reflectivity

MXenes are a large family of two-dimensional materials that are attractive for energy storage due to their high-rate charging capabilities as well as for electrochemical actuators, water purification, and many other technologies. Ion intercalation during electrochemically driven charge and discharge processes is the fundamental process associated with MXene functionality, which we have characterized here using in situ and operando X-ray reflectivity (XRR). Experiments performed at the Advanced Photon Source at Argonne National Laboratory monitored the changes in the structure of a Ti 3 C 2 MXene film on a platinum current collector as a function of static applied potential between 0.3 and –0.7 V vs Ag/AgCl in an aqueous 0.1 M Li 2 SO 4 electrolyte. Negative potential sweeps lead to a contraction of 1.2 Å in the interlayer spacing and a loss of electron density between the layers, likely due to Li + ion insertion and water removal. The change in lattice spacing includes a continuous variation vs potential as well as an additional discrete contraction that occurs near –0.35 V that has the characteristics of a first-order transition. The continuous change in the MXene interlayer spacing is associated with the capacitive charge, while the discrete change in structure correlated to the weak feature in the cyclic voltammogram at –0.35 V can be interpreted as either a pseudocapacitive charging process or a potential-dependent change in capacity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗