Search NASA⌕ Search

SEARCH · Search NASA

Results for “nodule”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Analysis of stress-strain, fracture and ductility behavior of aluminum matrix composites containing discontinuous silicon carbide reinforcement

Mechanical properties and stress-strain behavior for several types of commercially fabricated aluminum matrix composites, containing up to 40 vol % discontinuous SiC whisker, nodule, or particulate reinforcement were evaluated. It was found that the elastic modulus of the composites was isotropic, to be independent of type of reinforcement, and to be controlled solely by the volume percentage of SiC reinforcement present. The yield/tensile strengths and ductility were controlled primarily by the matrix alloy and temper condition. Ductility decreased with increasing reinforcement content, however, the fracture strains observed were higher than those reported in the literature for this type of composite. This increase in fracture strain is attributed to cleaner matrix powder and increased mechanical working during fabrication. Conventional aluminum and titanium structural alloys were compared and have shown that the properties of these low cost, lightweight composites have good potential for application to aerospace structures.

Mcdanels, D. L.↗
NASA NTRS1984

'Fluffy' Type A Ca-, Al-rich inclusions in the Allende meteorite

Inclusions called 'fluffy' Type A's or FTA's in the Allende meteorite are examined as possible candidates for relict vapor-solid condensate grains, remaining from the original solar nebula. Type A inclusions are characterized by abundant melilite and absence of primary anorthite and titaniferous pyroxene. Fluffy Type A's were probably loosely bound clumps of crystals drifting in the solar nebula, analogous to dustballs or snowflakes. Polished thin sections of all samples were studied optically and with a JEOL JSM-35 scanning electron microscope. It is reasonably clear that neither whole FTA's nor constituent nodules of the coarser grained ones were ever molten. Despite solid-state recrystallization which has affected these inclusions to varying degrees, the coarser grained material remaining in many of them is probably a relic of vapor-solid condensation in the solar nebula.

Macpherson, G. J.↗
NASA NTRS1984

Directional solidification of flake and nodular cast iron during KC-135 low-g maneuvers

Alloys solidified in a low-gravity environment can, due to the elimination of sedimentation and convection, form unique and often desirable microstructures. One method of studying the effects of low-gravity (low-g) on alloy solidification was the use of the NASA KC-135 aircraft flying repetitive low-g maneuvers. Each maneuver gives from 20 to 30 seconds of low-g which is between about 0.1 and 0.001 gravity. A directional solidification furnace was used to study the behavior of off eutectic composition case irons in a low-g environment. The solidification interface of hypereutectic flake and spheroidal graphite case irons was slowly advanced through a rod sample, 5 mm in diameter. Controlled solidification was continued through a number of aircraft parabolas. The known solidification rate of the sample was then correlated with accelerometer data to determine the gravity level during solidification for any location of the sample. The thermal gradient and solidification rate were controlled independently. Samples run on the KC-135 aircraft exhibited bands of coarser graphite or of larger nodules usually corresponding to the regions solidified under low-g. Samples containing high phosphorous (used in order to determine the eutectic cell) exhibited larger eutectic cells in the low-g zone, followed by a band of coarser graphite.

Curreri, P. A.↗
NASA NTRS1985

Processes and imagery of first-year fast sea ice during the melt season

In June and July 1982, a field program was conducted in the Canadian Arctic on Prince Patrick Island to study sea ice during the melt season with in situ measurements and microwave instrumentation operated near the surface and from aircraft. The objective of the program was to measure physical characteristics together with microwave backscatter and emission coefficients of sea ice during this major period of transition. The present paper is concerned with a study of both surface measurements and imagery of first-year fast ice during the melt season. The melting process observed in first-year fast ice was found to begin with the gradual reduction of the snow cover. For a two- to three-day period in this melt stage, a layer of superimposed ice nodules formed at the snow/ice interface as meltwater froze around ice and snow grains.

Holt, B.↗
NASA NTRS1985

Analysis of stress-strain, fracture, and ductility behavior of aluminum maxtrix composites containing discontinuous silicon carbide reinforcement

Mechanical properties and stress-strain behavior were evaluated for several types of commercially fabricated aluminum matrix composites, containing up to 40 vol pct discontinuous SiC whisker, nodule, or particulate reinforcement. The elastic modulus of the composites was found to be isotropic, to be independent of type of reinforcement, and to be controlled solely by the volume percentage of SiC reinforcement present. The yield/tensile strengths and ductility were controlled primarily by the matrix alloy and temper condition. Type and orientation of reinforcement had some effect on the strengths of composites, but only for those in which the whisker reinforcement was highly oriented. Ductility decreased with increasing reinforcement content; however, the fracture strains observed were higher than those reported in the literature for this type of composite. This increase in fracture strain was probably attributable to cleaner matrix powder, better mixing, and increased mechanical working during fabrication. Comparison of properties with conventional aluminum and titanium structural alloys showed that the properties of the low-cost, lightweight composites demonstrated very good potential for application to aerospace structures.

Mcdanels, D. L.↗
NASA NTRS1985

Impact melt products of chondritic material

Experimental data concerning impact melting processes in chondritic material are reviewed. It is shown that a large variety of objects in chondritic meteorites could have formed as a result of impact melting, including: shock veins; metal-troilite mixtures; metal and sulfide nodules; melt pockets and vugs. The type of object produced in an impact melt is related to the interaction of the shock waves with the particular target rock. It is suggested that various iron meteorites (including groups IAB, IIICD, and IIE, as well as several ungrouped irons) were formed from individual melt pools in chondritic regoliths. The small-scale structure of impact-melted metallic Fe,Ni and troilite in Weston (H chondrite regolith breccia) is illustrated in a photograph.

Rubin, A. E.↗
NASA NTRS1985

A refractory inclusion in the Kaba CV3 chondrite - Some implications for the origin of spinel-rich objects in chondrites

The first detailed petrographic and mineralogical study of a Ca, Al-rich inclusion (CAI) from the Kaba CV3 chondrite is reported. This 'fine-grained' CAI contains abundant small, rounded, rimmed, spinel-rich objects which have important features in common with the spinel-rich objects in other carbonaceous and ordinary chondrites. These nodules are interpreted as fractionated distillation residues of primitive dust. However, the available data do not unambiguously rule out a condensation origin for at least some of these objects. Finally, the preservation of distinct diopside-hedenbergite rims on the spinel-rich bodies and the small grain size of many minerals in the CAI matrix material both suggest that the CAI accreted cool and had a relatively cool thermal history in the Kaba parent body.

Fegley, B., Jr.↗
NASA NTRS1986

Properties of the Guin ungrouped iron meteorite - The origin of Guin and of group-IIE irons

The composition and structure of the Guin ungrouped iron meteorite inclusions have been investigated experimentally. The structural characteristics of polished and etched slabs of the meteorite were studied microscopically in reflected light. Modal abundances of troilite nodules and silicate inclusions were determined by weighing paper traces. The bulk composition of the silicate inclusions was calculated by combining modal phase abundances and mineral compositions. It is found that the largest silicate inclusion (2 x 4 cm) consists mostly of a shock-melted plagioclase-rich matrix surrounding large, partly melted augite grains. The oxygen isotopic composition of the inclusion is near that of LL chondrites. The inclusion is found to be similar in composition to selected melt pocket glasses in ordinary chondrites produced in situ by preferential melting of plagioclase rock due to shock compression. It is suggested that the Guin assemblage was formed by impact melting on a chondritic parent body. Silicate inclusions in IIE irons share many of the compositional and petrological characteristics of the Guin inclusions, indicating that IIE irons also formed by impact-melting of chondritic materials. Black and white photomicrographs of the silicate inclusions are provided.

Rubin, A. E.↗
NASA NTRS1985

Geochemical and petrological sampling and studies at the first moon base

Strategic sampling appropriate to the first-order lunar base can advance a variety of first-order lunar geochemical and petrological problems. Field observation and collection of samples would be done on the lunar surface, but detailed analysis would be done mainly in terrestrial laboratories. Among the most important areas of investigation for which field observations can be made and samples can be collected at the initial base are regolith studies, studies of mare and highlands stratigraphy, and a search for rare materials such as mantle nodules. Since the range of exploration may be limited to a radius of about 20 km from the first lunar base, locating the base near a mare-highlands boundary would enable the greatest latitude in addressing these problems.

Haskin, L. A.↗
NASA NTRS1986

Shuttle Imaging Radar - Physical controls on signal penetration and subsurface scattering in the Eastern Sahara

Interpretation of Shuttle Imaging Radar-A (SIR-A) images by McCauley et al. (1982) dramatically changed previous concepts of the role that fluvial processes have played over the past 10,000 to 30 million years in shaping this now extremely flat, featureless, and hyperarid landscape. In the present paper, the near-surface stratigraphy, the electrical properties of materials, and the types of radar interfaces found to be responsible for different classes of SIR-A tonal response are summarized. The dominant factors related to efficient microwave signal penetration into the sediment blanket include (1) favorable distribution of particle sizes, (2) extremely low moisture content and (3) reduced geometric scattering at the SIR-A frequency (1.3 GHz). The depth of signal penetration that results in a recorded backscatter, here called 'radar imaging depth', was documented in the field to be a maximum of 1.5 m, or 0.25 of the calculated 'skin depth', for the sediment blanket. Radar imaging depth is estimated to be between 2 and 3 m for active sand dune materials. Diverse permittivity interfaces and volume scatterers within the shallow subsurface are responsible for most of the observed backscatter not directly attributable to grazing outcrops. Calcium carbonate nodules and rhizoliths concentrated in sandy alluvium of Pleistocene age south of Safsaf oasis in south Egypt provide effective contrast in premittivity and thus act as volume scatterers that enhance SIR-A portrayal of younger inset stream channels.

Schaber, G. G.↗
NASA NTRS1987

Directional Solidification of Nodular Cast Iron

Cerium enhances formation of graphite nodules. Preliminary experiments in directional solidification of cast iron shows quantitative correlation of graphite microstructure with growth rate and thermal gradient, with sufficient spheroidizing element to form spheroidal graphite under proper thermal conditions. Experimental approach enables use of directional solidification to study solidification of spheriodal-graphite cast iron in low gravity. Possible to form new structural materials from nodular cast iron.

Curreri, P. A.↗
NASA NTRS1986

A comparative petrologic study of iron meteorites with radiogenic Ag-107 anomalies

The characteristics of the sulfide and metal phases of Derrick Peak, Cape York, Grant, Gibeon, and Santa Clara iron meteorite samples are examined. The textures and mineralogies of the samples are described. The effects of thermal and shock events on the distribution of Ag, and the relationship between Ag-107 and Pd are investigated. The correlation between the thermal histories and metal and sulfide nodules of the Gibeon and Santa Clara specimens is analyzed. It is noted that the Pd-107-Ag107 systematics involve the isotopic chemistry and cooling history of iron meteorites, the intensity of late extraterrestrial shock occurrences, and thermal processing.

Teshima, J.↗
NASA NTRS1988

Lithospheric evolution of the Northern Arabian Shield: Chemical and isotopic evidence from basalts, xenoliths and granites

The evolution of the upper-mantle and the lower-crust (the conteinental lithosphere), is the area of Israel and Sinai was studied, using the chemical composition and the Nd-Sr isotopic systematics from mantle and crustal nodules, their host basalts, and granites. The magmatism and the metasomatism making the lithosphere are related to uprise of mantle diapirs in the uppermost mantle of the area. These diapirs heated the base of the lithosphere, eroded, and replaced it with new hot material. It caused a domal uplift of the lithosphere (and the crust). The doming resulted in tensional stresses that in turn might develop transport channels for the basalt.

Stein, M.↗
NASA NTRS1990

On the determination of iridium in diverse geological samples employing HPGe-coincidence/NaI(Tl)-anticoincidence spectrometry

This paper reports the Ir content of a variety of geological samples determined by the high-purity Ge-coincidence/NaI(Tl)-anticoincidence gamma-ray spectrometry (henceforth referred to as coincidence/anticoincidence technique) and by the conventional INAA. The advantages of this technique are: (1) the Ir content of the samples is obtained (ppm to a fraction of ppb ranges) not only by the 468.1 keV peak as in the conventional INAA but also by the 784.6 keV and 920.9 keV sum peaks, which gives more confidence in the values obtained; and (2) it is well suited for the samples with high Compton background for which it is difficult to measure the Ir content by the conventional INAA technique. The practical sensitivity of this technique depends on the sample matrix. Under present experimental conditions, it varied from 0.1 ng for Mn nodules and 0.004 ng for Libyan Desert Glass. Iridium values obtained on small (about 1 microg) olivine grains demonstrate the potential application of this new technique to microsamples. The principle and methodology of this new technique as well as its advantages and disadvantages over the conventional INAA are discussed.

Murali, A. V.↗
NASA NTRS1990

Functionalized poly(arylene ethers) as toughness modifiers for bismaleimides

A family of novel, low molecular weight functionalized poly(arylene ether) resins has been investigated to ascertain its members' toughness-imparting contribution to neat bismaleimide (BMI) resin and BMI-matrix laminate composite properties. Attention is given to the contribution of the reactive poly(arylene ether)'s backbone chemistry to fracture toughness, as well as to the comparative influence of high and low molecular weight reactive poly(arylene ether) types on the modified BMI resin systems. The modified BMIs possess a polyphase morphology, with good adhesion between the thermoplastic nodules and the host thermoset systems.

Stenzenberger, H. D.↗
NASA NTRS1991

Evolution of ore deposits on terrestrial planets

Ore deposits on terrestrial planets materialized after core formation, mantle evolution, crustal development, interactions of surface rocks with the hydrosphere and atmosphere, and, where life exists on a planet, the involvement of biological activity. Core formation removed most of the siderophilic and chalcophilic elements, leaving mantles depleted in many of the strategic and noble metals relative to their chondritic abundances. Basaltic magma derived from partial melting of the mantle transported to the surface several metals contained in immiscible silicate and sulfide melts. Magmatic ore deposits were formed during cooling, fractional crystallization and density stratification from the basaltic melts. Such ore deposits found in earth's Archean rocks were probably generated during early histories of all terrestrial planets and may be the only types of igneous ores on Mars. Where plate tectonic activity was prevalent on a terrestrial planet, temporal evolution of ore deposits took place. Repetitive episodes of subduction modified the chemical compositions of the crust and upper mantles, leading to porphyry copper and molybdenum ores in calc-alkaline igneous rocks and granite-hosted tin and tungsten deposits. Such plate tectonic-induced mineralization in relatively young igneous rocks on earth may also have produced hydrothermal ore deposits on Venus in addition to the massive sulfide and cumulate chromite ores associated with Venusian mafic igneous rock. Sedimentary ore deposits resulting from mechanical and chemical weathering in reducing atmospheres in Archean earth included placer deposits (e.g., uraninite, gold, pyrite ores). Chromite, ilmenite, and other dense unreactive minerals could also be present on channel floors and in valley networks on Mars, while banded iron formations might underlie the Martian northern plains regions. As oxygen evolved in earth's atmosphere, so too did oxide ores. By analogy, gossans above sulfide ores probably occur on Mars, but not submarine ferromanganese nodules and crusts which have precipitated in oxygenated seawater on earth.

Burns, R. G.↗
NASA NTRS1990

Electron microscopy study of the iron meteorite Santa Catharina

A characterization of the microstructural features of Santa Catharina (SC) from the millimeter to submicron scale is presented. The same specimen was examined using an optical microscope, a scanning electron microscope, an electron probe microanalyzer, and an analytical electron microscope. Findings include the fact that SC metal nodules may have different bulk Ni values, leading to different microstructures upon cooling; that SC USNM 6293 is the less corroded sample, as tetrataenite exists as less than 10 nm ordered domains throughout the entire fcc matrix (it is noted that this structure is the same as that of the Twin City meteorite and identical to clear taenite II in the retained taenite regions of the octahedrites); that SC USNM 3043 has a more complicated microstructure due to corrosion; and that the low Ni phase of the cloudy zone was selectively corroded in some areas and formed the dark regions, indicating that the SC meteorite corrosion process was electrochemical in nature and may involve Cl-containing akaganeite.

Zhang, J.↗
NASA NTRS1991

Cartilage formation in the CELLS 'double bubble' hardware

The CELLS experiment scheduled to be flown on the first International Microgravity Laboratory is designed to study the effect of microgravity on the cartilage formation, by measuring parameters of growth in a differentiating cartilage cell culture. This paper investigates the conditions for this experiment by studying cartilage differentiation in the 'bubble exchange' hardware with the 'double bubble' design in which the bubbles are joined by a flange which also overlays the gasket. Four types of double bubbles (or double gas permeable membranes) were tested: injection-molded bubbles 0.01- and 0.005-in. thick, and compression molded bubbles 0.015- and 0.01-in. thick. It was found that double bubble membranes of 0.005- and 0.010-in. thickness supported cartilage differentiation, while the 0.015-in. bubbles did not. It was also found that nodule count, used in this study as a parameter, is not the best measure of the amount of cartilage differentiation.

Duke, P. J.↗