SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In considering nonlinearities in spacecraft structural dynamics, the following are examined: (1) SCOLE Configuration-Equations of Motion; (2) Modeling Error Sources; (3) Approximate Solutions; (4) Comparison of Model Accuracy; (5) Linear and Nonlinear Damping; (6) Experimental Results; and, (7) Future Work.
This paper describes a testbed developed to study control of manipulator-coupled spacecraft with active attitude control systems. Pre-design simulation studies are described that were used to size and design the experimental facility and plan testing programs. Results on the dynamics and control of this testbed are presented that were obtained from both simulations and experiments. Initial experimental results have been used to refine the simulators using output matching system identification. Results from this system identification are included in the form of comparisons between simulation and experiment time histories for various model parameter values. These show that the testbed is inherently nonlinear and that parameters, harmonic gear effectiveness, in particular, have appreciable effects on the dynamics.
In this paper, some of the effects of unbalance on the nonlinear response and stability of flexible rotor-bearing systems is presented from both a theoretical and experimental standpoint. In a linear system, operating above its stability threshold, the amplitude of motion grows exponentially with time and the orbits become unbounded. In an actual system, this is not necessarily the case. The actual amplitudes of motion may be bounded due to various nonlinear effects in the system. These nonlinear effects cause limit cycles of motion. Nonlinear effects are inherent in fluid film bearings and seals. Other contributors to nonlinear effects are shafts, couplings and foundations. In addition to affecting the threshold of stability, the nonlinear effects can cause jump phenomena to occur at not only the critical speeds, but also at stability onset or restabilization speeds.
The structural dynamic properties of trusses are strongly affected by the characteristics of joints connecting the individual beam elements. Joints are particularly significant in that they are often the source of nonlinearities and energy dissipation. While the joints themselves may be physically simple, direct measurement is often necessary to obtain a mathematical description suitable for inclusion in a system model. Force state mapping is a flexible, practical test method for obtaining such a description, particularly when significant nonlinear effects are present. It involves measurement of the relationship, nonlinear or linear, between force transmitted through a joint and the relative displacement and velocity across it. An apparatus and procedure for force state mapping are described. Results are presented from tests of joints used in a lightweight, composite, deployable truss built by the Boeing Aerospace Company. The results from the joint tests are used to develop a model of a full 4-bay truss segment. The truss segment was statically and dynamically tested. The results of the truss tests are presented and compared with the analytical predictions from the model.
The objective of the research has been to study the design of adaptive/learning control systems for the control of large flexible structures. In the first activity an adaptive/learning control methodology for flexible space structures was investigated. The approach was based on using a modal model of the flexible structure dynamics and an output-error identification scheme to identify modal parameters. In the second activity, a least-squares identification scheme was proposed for estimating both modal parameters and modal-to-actuator and modal-to-sensor shape functions. The technique was applied to experimental data obtained from the NASA Langley beam experiment. In the third activity, a separable nonlinear least-squares approach was developed for estimating the number of excited modes, shape functions, modal parameters, and modal amplitude and velocity time functions for a flexible structure. In the final research activity, a dual-adaptive control strategy was developed for regulating the modal dynamics and identifying modal parameters of a flexible structure. A min-max approach was used for finding an input to provide modal parameter identification while not exceeding reasonable bounds on modal displacement.
Various experimental, analytical, and numerical analysis methods for flow-solid interaction of a nest of cylinders subjected to cross flows are reviewed. A nest of cylinders subjected to cross flows can be found in numerous engineering applications including the Space Shuttle Maine Engine-Main Injector Assembly (SSME-MIA) and nuclear reactor heat exchangers. Despite its extreme importance in engineering applications, understanding of the flow-solid interaction process is quite limited and design of the tube banks are mostly dependent on experiments and/or experimental correlation equations. For future development of major numerical analysis methods for the flow-solid interaction of a nest of cylinders subjected to cross flow, various turbulence models, nonlinear structural dynamics, and existing laminar flow-solid interaction analysis methods are included.
A new impact debris propagation code was written to link CTH simulations of space debris shield perforation to the Lagrangian finite element code DYNA3D, for space structure wall impact simulations. This software (DC3D) simulates debris cloud evolution using a nonlinear elastic-plastic deformable particle dynamics model, and renders computationally tractable the supercomputer simulation of oblique impacts on Whipple shield protected structures. Comparison of three dimensional, oblique impact simulations with experimental data shows good agreement over a range of velocities of interest in the design of orbital debris shielding. Source code developed during this research is provided on the enclosed floppy disk. An abstract based on the work described was submitted to the 1994 Hypervelocity Impact Symposium.
Motivated by experiments on chains of superconducting qubits, we consider the dynamics of a classical Klein-Gordon chain coupled to coherent driving and subject to dissipation solely at its boundaries. As the strength of the boundary driving is increased, this minimal classical model recovers the main features of the "dissipative phase transition" seen experimentally. Between the transmitting and non-transmitting regimes on either side of this transition (which support ballistic and diffusive energy transport respectively), we observe additional dynamical regimes of interest. These include a regime of superdiffusive energy transport at weaker driving strengths, together with a "dissipative breather crystal" regime at stronger driving strengths, which is characterized by emergent translation symmetry, ballistic energy transport, and coherent oscillations of a nonlinear normal mode. Here, we propose a non-local Lyapunov exponent as an experimentally measurable diagnostic of many-body chaos in this system, and more generally in open systems that are only coupled to an environment at their boundaries.
The quantum features of ultrashort-pulse optical parametric oscillators (OPOs) are investigated theoretically in the nonlinear regime near and above threshold. Viewing the pulsed OPO as a multimode open quantum system, we rigorously derive a general input-output model that features nonlinear coupling among many cavity (i.e., system) signal modes and a broadband single-pass (i.e., reservoir) pump field. Under appropriate assumptions, our model produces a Lindblad master equation with multimode nonlinear Lindblad operators describing two-photon dissipation and a multimode four-wave-mixing Hamiltonian describing a broadband, dispersive optical cascade, which we show is required to preserve causality. To simplify the multimode complexity of the model, we employ a supermode decomposition to perform numerical simulations in the regime where the pulsed supermodes experience strong single-photon nonlinearity. We find that the quantum nonlinear dynamics induces pump depletion as well as corrections to the below-threshold squeezing spectrum predicted by linearized models. We also observe the formation of non-Gaussian states with Wigner-function negativity and show that the multimode interactions with the pump, both dissipative and dispersive, can act as effective decoherence channels. Finally, we briefly discuss some experimental considerations for potentially observing such quantum nonlinear phenomena with ultrashort-pulse OPOs on nonlinear nanophotonic platforms.
Spatially periodic large amplitude solutions of the von Karman model are obtained in the neighborhood of singularities. These singularities correspond to vortex clusters in the physical plane. The quasi-periodic and unbounded solutions found analytically confirm earlier numerical work and show qualitative agreement with experimental observations of large-scale phenomena of vortex trails. Separatrices or heteroclinic orbits were explicitly found for an integrable approximate equation, which indicate that the von Karman model itself supports chaotic solutions.
The experimental results of the Middick Zero-gravity Dynamics Experiment (MODE) are presented. MODE investigated the dynamics of two key spacecraft components; contained fluids and jointed truss structures. The change in the lateral slosh behavior of contained fluids and the changes in the modal parameters of space structural test articles from one- to zero-gravity were studied. The experimental apparatus used to determine the dynamic characteristics is described. For the MODE fluid experiments, the forced response characteristics of silicone oil and distilled water in cylinder tanks with either a flat or spherical bottom are reported and discussed. A comparison of the measured earth and space results identifies and highlights the effects of gravity on the linear and nonlinear slosh behavior of these fluids. For the MODE structural experiments, an analytic and experimental study is presented. Deployable, erectable, and rotary modules were assembled to form three one- and two-dimensional structures in which variations in bracing wire and rotary joint preload could be introduced. Analysis is compared with ground experimental measurements made on a spring/wire suspension system with a nominal plunge frequency of one Hertz, and with measurements made on the Shuttle middeck. The degree of change in linear modal parameters as well as the change in nonlinear nature of the response is examined. Trends in modal parameters are presented as a function of force amplitude, joint preload, and ambient gravity level.
This report describes structural aviation crash dynamics research activities being conducted on general aviation aircraft and transport aircraft. The report includes experimental and analytical correlations of load-limiting subfloor and seat configurations tested dynamically in vertical drop tests and in a horizontal sled deceleration facility. Computer predictions using a finite-element nonlinear computer program, DYCAST, of the acceleration time-histories of these innovative seat and subfloor structures are presented. Proposed application of these computer techniques, and the nonlinear lumped mass computer program KRASH, to transport aircraft crash dynamics is discussed. A proposed FAA full-scale crash test of a fully instrumented radio controlled transport airplane is also described.
Conical shell theory and a supersonic potential flow aerodynamic theory are used to study the nonlinear pressure buckling and aeroelastic limit cycle behavior of the thermal protection system for NASA's Hypersonic Inflatable Aerodynamic Decelerator. The structural model of the thermal protection system consists of an orthotropic conical shell of the Donnell type, resting on several circumferential elastic supports. Classical Piston Theory is used initially for the aerodynamic pressure, but was found to be insufficient at low supersonic Mach numbers. Transform methods are applied to the convected wave equation for potential flow, and a time-dependent aerodynamic pressure correction factor is obtained. The Lagrangian of the shell system is formulated in terms of the generalized coordinates for all displacements and the Rayleigh-Ritz method is used to derive the governing differential-algebraic equations of motion. Aeroelastic limit cycle oscillations and buckling deformations are calculated in the time domain using a Runge-Kutta method in MATLAB. Three conical shell geometries were considered in the present analysis: a 3-meter diameter 70 deg. cone, a 3.7-meter 70 deg. cone, and a 6-meter diameter 70 deg. cone. The 6-meter configuration was loaded statically and the results were compared with an experimental load test of a 6-meter HIAD. Though agreement between theoretical and experimental strains was poor, the circumferential wrinkling phenomena observed during the experiments was captured by the theory and axial deformations were qualitatively similar in shape. With Piston Theory aerodynamics, the nonlinear flutter dynamic pressures of the 3-meter configuration were in agreement with the values calculated using linear theory, and the limit cycle amplitudes were generally on the order of the shell thickness. The effect of axial tension was studied for this configuration, and increasing tension was found to decrease the limit cycle amplitudes when the circumferential elastic supports were neglected, but resulted in more complex behavior when the supports were included. The nominal flutter dynamic pressure of the 3.7-meter configuration was significantly lower than that of the 3-meter, and it was found that two sets of natural modes coalesce to flutter modes near the same dynamic pressure. This resulted in a significant drop in the limit cycle frequencies at higher dynamic pressures, where the flutter mode with the lower frequency becomes more critical. Pre-buckling pressure loads and the aerodynamic pressure correction factor were studied for all geometries, and these effects resulted in significantly lower flutter boundaries compared with Piston Theory alone. The maximum dynamic pressure predicted by aerodynamic simulations of a proposed 3.7-meter HIAD vehicle was still lower than any of the calculated flutter dynamic pressures, suggesting that aeroelastic effects for this vehicle are of little concern.
We consider examples of J-OCTA software application to physics-based analysis of in-space manufacturing technologies. Firstly, we consider an atomistic model of thermal welding at the polymer-polymer interface for applications to 3D manufacturing by following diffusion of polymer chains. We show that each component of the polymer blend has its own characteristic time of diffusion and that both strain–stress and shear viscosity curves agree with experimental data. Next, nonlinear shrinkage of the metal part during manufacturing by bound metal deposition under microgravity, is considered using a multi-scale physics-based approach that spans from atomistic dynamics to full-part shrinkage. At the smallest scale we use atomistic dynamics to simulated sintering of a few Ti6Al4V nanoparticles, study sintering mechanisms and estimate important parameters including grain boundary width and diffusion rates of the atoms at the surface that are used at the other scales of modelling. Finally, we analyse selective ionic conduction through an artificial nanopore in a graphene sheet motivated by applications to desalination and energy harvesting. We build distributions of the number and orientation of water molecules in the ion’s hydration shells providing novel insight into the ion-water-carbon interaction at the nanopore.
An envelope equation is used to explore the propagation of a focused electron beam through dense conductive media like partially ionized high-pressure gas, metal vapor plumes from beam-target interactions, or low-density solid-phase targets. Envelope equations have been a most useful tool for predicting experimental results of beam propagation in gas, and they are refined for the general problem of propagation through a dense medium. The envelope equation is modified to account for the large beam divergence resulting from multiple scattering. The envelope code results are in qualitative agreement with published experimental data. Published by the American Physical Society 2025
Nonlinear force appropriation is an extension of its linear counterpart where sinusoidal excitation is applied to a structure with a modal shaker and phase quadrature is achieved between the excitation and response. While a standard practice in modal testing, modal shaker excitation has the potential to alter the dynamics of the structure under test. Previous studies have been conducted to address several concerns, but this work specifically focuses on a shaker-structure interaction phenomenon which arises during the force appropriation testing of a nonlinear structure. Under pure-tone sinusoidal forcing, a nonlinear structure may respond not only at the fundamental harmonic but also potentially at sub- or superharmonics, or it can even produce aperiodic and chaotic motion in certain cases. Shaker-structure interaction occurs when the response physically pushes back against the shaker attachment, producing non-fundamental harmonic content in the force measured by the load cell, even for pure tone voltage input to the shaker. This work develops a model to replicate these physics and investigates their influence on the response of a nonlinear normal mode of the structure. Experimental evidence is first provided that demonstrates the generation of harmonic content in the measured load cell force during a force appropriation test. This interaction is replicated by developing an electromechanical model of a modal shaker attached to a nonlinear, three-mass dynamical system. Several simulated experiments are conducted both with and without the shaker model in order to identify which effects are specifically due to the presence of the shaker. Finally, the results of these simulations are then compared to the undamped nonlinear normal modes of the structure under test to evaluate the influence of shaker-structure interaction on the identified system’s dynamics.
Electrochemical reduction of CO 2 gas is a novel CO 2 utilization technique that has the potential to mitigate the global climate crisis caused by anthropogenic CO 2 emissions, and enable the large-scale storage of energy generated from renewable sources in the form of carbon-based chemicals and fuels. However, due to the complexity of the electrochemical reactions, the explicit first-principles models for CO2 reduction are not available yet, and there has been a limited effort to develop process modeling, optimization and control of CO 2 electrochemical reactors. To this end, a rotating cylinder electrode (RCE) reactor has been constructed at UCLA to understand the mass transfer and reaction kinetics effects separately on the productivity. In the RCE reactor, the applied potential strongly influences the reaction energetics and the electrode rotation speed affects the hydrodynamic boundary layer and modifies the film mass transfer coefficient, which involves convective and diffusive transport. Further, the present work aims to develop a multi-input multi-output (MIMO) control scheme for the RCE reactor that integrates techniques from artificial and recurrent neural network modeling, nonlinear optimization, and process controller design. Specifically, production rates of two products from the experimental reactor, ethylene and carbon monoxide, are controlled by manipulating two inputs, applied potential and catalyst rotation speed. Process dynamics and controllability are analyzed, a feedback control strategy is designed and the controllers are tuned accordingly. The experimental electrochemical cell is employed to gather data for process modeling and implement the multivariable control system. Finally, the experimental results are presented which demonstrate excellent closed-loop performance by the control system and regulation of the outputs at three different set-points including an economically-optimal set-point.
The General Rotorcraft Aeromechanical Stability Program (GRASP) was developed to analyse the steady-state and linearized dynamic behavior of rotorcraft in hovering and axial flight conditions. Because of the nature of problems GRASP was created to solve, the geometrically nonlinear behavior of beams is one area in which the program must perform well in order to be of any value. Numerical results obtained from GRASP are compared to both static and dynamic experimental data obtained for a cantilever beam undergoing large displacements and rotations caused by deformations. The correlation is excellent in all cases.