Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter continuation method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

The scaling of secondary craters

Secondary craters are common features around fresh planetary-scale primary impact craters throughout most of the Solar System. They derive from the ejection phase of crater formation, thus secondary scaling relations provide constraints on parameters affecting ejection processes. Secondary crater fields typically begin at the edge of the continuous ejecta blankets (CEB) and extend out several crater radii. Secondaries tend to have rounded rims and bilateral symmetry about an axis through the primary crater's center. Prominent secondary chains can extend inward across the CEB close to the rim. A simple method for comparing secondary crater fields was employed: averaging the diameters and ranges from the center of the primary crater of the five largest craters in a secondary crater field. While not as much information is obtained about individual crater fields by this method as in more complete secondary field mapping, it facilitates rapid comparison of many secondary fields. Also, by quantifying a few specific aspects of the secondary crater field, this method can be used to construct scaling relations for secondary craters.

Croft, Steven K.↗
NASA NTRS2012

On Optimal Control of Non-Autonomous Switched Systems with a Fixed Mode Sequence

We consider differentiability with respect to the switch times of the value function of an optimal control problem for a non-autonomous switched system. The control variables are the switch times between the modes and the input in each mode. We provide a method to compute the derivative of the cost function given a nominal input. Then, we view the optimal control problem as a parametrized optimization problem in which the switch times are the parameters and the optimization is over the set of feasible inputs of each mode. From this point of view, we provide conditions under which the continuity and differentiability of the optimal value function, that is the cost function optimized over the inputs, can be guaranteed.

Kamgarpour, Maryam↗
NASA NTRS1980

Stress wave attenuation in thin structures by ultrasonic through-transmission

The steady state amplitude of the output of an ultrasonic through transmission measurement is analyzed and the result is given in closed form. Provided that the product of the input and output transduction ratios; the specimen-transducer reflection coefficient; the specimen-transducer phase shift parameter; and the material phase velocity are known, this analysis gives a means for determining the through-thickness attenuation of an individual thin sample. Multiple stress wave reflections are taken into account and so signal echoes do not represent a difficulty. An example is presented for a graphite fiber epoxy composite (Hercules AS/3501-6). A direct method for continuous or intermittent monitoring of through thickness attenuation of plate structures which may be subject to service structural degradation is provided.

Lee, S. S.↗
NASA NTRS1985

The cosmic ray differential diurnal variation dependences on the zenith angle and the geomagnetic disturbance

Simultaneous and continuous muon measurements in two opposite azimuthal directions under equal zenith angles demonstrated the importance of this method for cosmic ray diurnal variation investigations. Lately these measurements were extended by means of improved telescopes. The obtained cosmic ray diurnal variations were presented as intensity differential curves. Theoretical investigations connected the properties of these curves with some interplanetary spece parameters. The harmonics of these curves were interpreted physically. Some order difference curves were introduced. In earlier works some dependences between the parameters characterizing the first and the second harmonics of the differential intensity curves and the geomagnetic activity were found. Then all measurements were carried out under only one zenith angle. The results of investigations of similar dependences using data of simultaneous measurements under three different zenith angles are presented.

Kavlakov, S.↗
NASA NTRS2016

Crystallographic Characterization of Extraterrestrial Materials by Energy-Scanning X-ray Diffraction

We have continued our long-term project using X-ray diffraction to characterize a wide range of extraterrestrial samples. The stationary sample method with polychromatic X-rays is advantageous because the irradiated area of the sample is always same and fixed, meaning that all diffraction spots occur from the same area of the sample, however, unit cell parameters cannot be directly obtained by this method though they are very important for identification of mineral and for determination of crystal structures. In order to obtain the cell parameters even in the case of the sample stationary method, we apply energy scanning of a micro-beam of monochromatic SR at SPring-8.

Hagiya, Kenji↗
NASA NTRS2024

Real-Time Temperature Field State Observer and Digital Replica to Support Cyber-Physical Testing

Cyber-physical testing is a class of experimental methods in which a system is partitioned into physical and numerical components to study its overall behavior. Transfer systems are typically needed to capture relevant interactions by enforcing appropriate interface conditions between the physical and numerical portions. While cyber-physical testing is often performed using lumped-parameter systems, thermomechanical cyber-physical testing requires the use of thermal actuators as transfer systems to apply a thermal condition over a spatially distributed region or surface. Thus, the interactions between the numerical and physical components are of a distributed nature, i.e., a field rather than point values. In this paper, we develop and experimentally validate a state observer for temperature fields to enable thermomechanical cyber-physical testing. The state observer provides continuous estimates of temperature over a surface of the thermal actuator using only temperature measurements at discrete locations. The estimated temperature field is then leveraged to account for localized mechanical defects in the interface condition. The method consists of building a digital replica of one portion of the control plant. By imposing defects in the digital replica it is used to generate and output the response of a thermal load pattern that represents that of a physical system with mechanical defects.

Manuel Salmeron↗
NASA NTRSDate not supplied

Terrestrial Analogue Studies from ISRO’s Venus Mission Perspective: Polarimetric Radar Properties of Hawaiian Lava Flows

Detection of present and past volcanism on Venus is one of the major goals of the proposed ISRO’s Venus orbiter mission. The S-band, high-resolution (40 m/pixel) fully Polarimetric Synthetic Aperture Radar (PolSAR) instrument on this mission [1] may have the capabilities to detect volcanism within the mission lifetime using repeated PolSAR imagery, and possibly SAR Interferometry (InSAR, experimental mode). The global mapping efforts of Venus by Magellan mission has enabled comprehensive mapping of lava flows and indicated that Venus has an extensive history of volcanism, the ages of which are largely unknown (e.g. [2]). While Magellan radar emissivity data (e.g. [3, 4]) and Near Infrared emissivity data from VIRTIS [5] suggested the occurrence of recent episodes of volcanic activity (e.g. Maat Mons and Ganis Chasma), as well as the presence of stratigraphically young lava flows (e.g. Idunn Mons), measuring changes in radar backscatter amplitude alone to identify lava flows has many challenges. Although very large changes in the shape of the terrain can be observed in radar backscatter amplitude changes (e.g. [6]), smaller, or relatively flat lava flows are difficult to detect. Previous terrestrial studies suggest that PolSAR and InSAR techniques are very effective for mapping lava flows (e.g. [7-9]), and can be used when changes cannot be distinguished in radar backscatter images. We use the unvegetated lava flows on Hawaiʻi island as a terrestrial analogue to study Venus lava flows for the following reasons: (a) It is extensively studied at several wavelengths commonly used in remote sensing studies (including PolSAR and InSAR methods); and (b) it is a volcanically active area with new lava flows frequently covering older emplaced flows. To investigate the surface roughness, texture, and fine-grained mantling associated with Mauna Loa and Kilauea lava flows, we utilize C- and L-band PolSAR datasets obtained from RISAT-1A (EOS-4) and ALOS PALSAR missions respectively. In particular, we will use the quad-polarized backscatter and polarimetric parameters to characterize the texture of the terrestrial lava flows to understand whether the Venus crust is continuously disrupted during flow emplacement. While some previous studies (e.g. [10, 11]) suggested that surface roughness of most of the Venus flows is comparable to that of terrestrial pāhoehoe flows, other studies indicated that fractal dimensions of some large lava flows on Venus imply high eruption rates which favour the formation of a’a flows (e.g. [12]). We will also analyse the terrestrial flows for the presence/absence of pyroclastic mantling as radar-bright diffuse deposits near the summit regions of some coronae on Venus have been proposed to be young pyroclastics, and possible evidence of a renewed epoch of mantle volcanism that taps into deeper volatiles [13]. A recent study using EOS-4 RISAT-1 data of a part of fresh Mauna Loa lava flows (2022 eruption) emphasizes the ability of fully polarimetric SAR data to understand the diversity of physical properties (e.g. texture and morphology) associated with them (Sreejith et al. 2024); and we will apply similar methods to the PolSAR data obtained from ISRO’s Venus mission for our proposed objectives.

Sriram S Bhiravarasu↗
NASA NTRS2016

Evaluation of the Effect of Surface Finish on High-Cycle Fatigue of SLM-IN718

The surface finish of parts produced by additive manufacturing processes is much rougher than the surface finish generated by machining processes, and a rougher surface can reduce the fatigue strength of a part. This paper discusses an effort to quantify that reduction of strength in high-cycle fatigue for selective laser melt (SLM) coupons. A high-cycle fatigue (HCF) knockdown factor was estimated for Inconel 718, manufactured with the SLM process. This factor is the percentage reduction from the maximum stress in fatigue for low-stress ground (LSG) specimens to the maximum stress of those left with the original surface condition at the same fatigue life. Specimens were provided by a number of vendors, free to use their "best practice"; only one heat treat condition was considered; and several test temperatures were characterized, including room temperature, 800F, 1000F, and 1200F. The 1000F data had a large variance, and was omitted from consideration in this document. A first method used linear approximations extracted from the graphs, and only where data was available for both. A recommended knockdown factor of the as-built surface condition (average roughness of approximately 245 micro-inches/inch) versus low-stress ground condition (roughness no more than 4 micro-inches/inch) was established at approximately 1/3 or 33%. This is to say that for the as-built surface condition, a maximum stress of 2/3 of the stress for LSG can be expected to produce a similar life in the as-built surface condition. In this first evaluation, the knockdown factor did not appear to be a function of temperature. A second approach, the "KP method", incorporated the surface finish measure into a new parameter termed the pseudo-stress intensity factor, Kp, which was formulated to be similar to the fracture mechanics stress intensity factor. Using Kp, the variance seemed to be reduced across all sources, and knockdown factors were estimated using Kp over the range where data occurred. A plot of the results suggests that the knockdown factor is a function of temperature, and that for low lives the knockdown might be lower than the knockdown observed above about one million cycles, where it tended to stabilize. This was not universal for all temperatures tested. The higher temperature tests are thought to be influenced by the test temperature, which perhaps continued the aging process. Further evaluation of the method is suggested.

Lambert, D. M.↗
NASA NTRS1988

Aeroacoustic research programs at the Army Aviation Research and Technology Activity

The Army rotorcraft aeroacoustic programs are reviewed, highlighting the theoretical and experimental progress made by Army researchers in the physical understanding of helicopter impulsive noise. The two impulsive noise sources addressed over this past decade are high-speed impulsive noise and blade-vortex interaction noise, both of which have had and will continue to have an increasing influence on Army rotorcraft design and operations. The advancements discussed are in the areas of in-flight data acquisition techniques, small-scale-model tests in wind tunnels, holographic interferometry/tomographic techniques, and the expanding capabilities of computational fluid dynamics in rotorcraft acoustic problems. Current theoretical prediction methods are compared with experimental data, and parameters that govern model scaling are established. The very successful cooperative efforts between the Army, NASA, and industry are also addressed

Yu, Yung H.↗
NASA NTRS1988

A parametric LQ approach to multiobjective control system design

The synthesis of a constant parameter output feedback control law of constrained structure is set in a multiple-objective linear quadratic regulator (MOLQR) framework. The use of intuitive objective functions such as model-following ability and closed-loop trajectory sensitivity allows multiple-objective decision-making techniques, such as the surrogate worth tradeoff method, to be applied. For the continuous-time deterministic problem with an infinite time horizon, dynamic compensators as well as static output feedback controllers can be synthesized using a descent Anderson-Moore algorithm modified to impose linear equality constraints on the feedback gains by moving in feasible directions. Results of three different examples are presented, including a unique reformulation of the sensitivity reduction problem.

Kyr, Doug↗
NASA NTRS2012

Ground Contact Model for Mars Science Laboratory Mission Simulations

The Program to Optimize Simulated Trajectories II (POST 2) has been successful in simulating the flight of launch vehicles and entry bodies on earth and other planets. POST 2 has been the primary simulation tool for the Entry Descent, and Landing (EDL) phase of numerous Mars lander missions such as Mars Pathfinder in 1997, the twin Mars Exploration Rovers (MER-A and MER-B) in 2004, Mars Phoenix lander in 2007, and it is now the main trajectory simulation tool for Mars Science Laboratory (MSL) in 2012. In all previous missions, the POST 2 simulation ended before ground impact, and a tool other than POST 2 simulated landing dynamics. It would be ideal for one tool to simulate the entire EDL sequence, thus avoiding errors that could be introduced by handing off position, velocity, or other fight parameters from one simulation to the other. The desire to have one continuous end-to-end simulation was the motivation for developing the ground interaction model in POST 2. Rover landing, including the detection of the postlanding state, is a very critical part of the MSL mission, as the EDL landing sequence continues for a few seconds after landing. The method explained in this paper illustrates how a simple ground force interaction model has been added to POST 2, which allows simulation of the entire EDL from atmospheric entry through touchdown.

Raiszadeh, Behzad↗
NASA NTRS2018

On the Natural Structure of Amino Acid Patterns in Families of Protein Sequences

All known terrestrial proteins are coded as continuous strings of ≈20 amino acids. The patterns formed by the repetitions of elements in groups of finite sequences describes the natural architectures of protein families. We present a method to search for patterns and groupings of patterns in protein sequences using a mathematically precise definition for “repetition”, an efficient algorithmic implementation and a robust scoring system with no adjustable parameters. We show that the sequence patterns can be well-separated into disjoint classes according to their recurrence in nested structures. The statistics of the occurrences of patterns indicate that short repetitions are sufficient to account for the differences between natural families and randomized groups of sequences by more than 10 standard deviations, while contiguous sequence patterns shorter than 5 residues are effectively random in their occurrences. A small subset of patterns is sufficient to account for a robust ”familiarity” definition between arbitrary sets of sequences.

Pablo Turjanski↗
NASA NTRS2011

Combined fast multipole-QR compression technique for solving electrically small to large structures for broadband applications

An approach that efficiently solves for a desired parameter of a system or device that can include both electrically large fast multipole method (FMM) elements, and electrically small QR elements. The system or device is setup as an oct-tree structure that can include regions of both the FMM type and the QR type. An iterative solver is then used to determine a first matrix vector product for any electrically large elements, and a second matrix vector product for any electrically small elements that are included in the structure. These matrix vector products for the electrically large elements and the electrically small elements are combined, and a net delta for a combination of the matrix vector products is determined. The iteration continues until a net delta is obtained that is within predefined limits. The matrix vector products that were last obtained are used to solve for the desired parameter.

Jandhyala, Vikram↗
NASA NTRS1978

A simple method for designing structural models with closely spaced modes of vibration

A simple method for designing a mathematical model with closely spaced vibration modes is described. The design process begins with a reference model having specified geometry, continuous inertia and stiffness distributions, and degrees of freedom, all of which remain unchanged. Two natural frequencies of this model are then forced together by means of systematic perturbation of the model's discrete inertia and stiffness parameters. There is only one eigenvalue solution per design cycle, and the gradient vector is calculated directly from the resulting modal quantities. The minimization procedure employed is unconstrained. As applications, a cantilevered plane grid model with five degrees of freedom and a bending-torsion-oscillator with eleven degrees of freedom are treated.

Hallauer, W. L., Jr.↗
NASA NTRS2014

A Multiscale Progressive Failure Modeling Methodology for Composites that Includes Fiber Strength Stochastics

A multiscale modeling methodology was developed for continuous fiber composites that incorporates a statistical distribution of fiber strengths into coupled multiscale micromechanics/finite element (FE) analyses. A modified two-parameter Weibull cumulative distribution function, which accounts for the effect of fiber length on the probability of failure, was used to characterize the statistical distribution of fiber strengths. A parametric study using the NASA Micromechanics Analysis Code with the Generalized Method of Cells (MAC/GMC) was performed to assess the effect of variable fiber strengths on local composite failure within a repeating unit cell (RUC) and subsequent global failure. The NASA code FEAMAC and the ABAQUS finite element solver were used to analyze the progressive failure of a unidirectional SCS-6/TIMETAL 21S metal matrix composite tensile dogbone specimen at 650 degC. Multiscale progressive failure analyses were performed to quantify the effect of spatially varying fiber strengths on the RUC-averaged and global stress-strain responses and failure. The ultimate composite strengths and distribution of failure locations (predominately within the gage section) reasonably matched the experimentally observed failure behavior. The predicted composite failure behavior suggests that use of macroscale models that exploit global geometric symmetries are inappropriate for cases where the actual distribution of local fiber strengths displays no such symmetries. This issue has not received much attention in the literature. Moreover, the model discretization at a specific length scale can have a profound effect on the computational costs associated with multiscale simulations.models that yield accurate yet tractable results.

Generalized Method of Cells↗
NASA NTRS2021

Integrating Inland and Coastal Water Quality Data for Actionable Knowledge

Water quality measures for inland and coastal waters are available as discrete samples from professional and volunteer water quality monitoring programs and higher-frequency, near-continuous data from automated in situ sensors. Water quality parameters also are estimated from model outputs and remote sensing. The integration of these data, via data assimilation, can result in a more holistic characterization of these highly dynamic ecosystems, and consequently improve water resource management. It is becoming common to see combinations of these data applied to answer relevant scientific questions. Yet, methods for scaling water quality data across regions and beyond, to provide actionable knowledge for stakeholders, have emerged only recently, particularly with the availability of satellite data now providing global coverage at high spatial resolution. In this paper, data sources and existing data integration frameworks are reviewed to give an overview of the present status and identify the gaps in existing frameworks. We propose an integration framework to provide information to user communities through the the Group on Earth Observations (GEO) AquaWatch Initiative. This aims to develop and build the global capacity and utility of water quality data, products, and information to support equitable and inclusive access for water resource management, policy and decision making.

Ghada Y.H. El Serafy↗
NASA NTRS1980

Stress-wave attenuation in thin structures by ultrasonic through-transmission

The steady-state amplitude of the output of an ultrasonic through-transmission measurement is analyzed and the result is given in closed form. Provided that the product of the input and output transduction ratios, the specimen-transducer reflection coefficient, the specimen-transducer phase-shift parameter, and the material phase velocity are known, this analysis gives a means for determining the through-thickness attenuation of an individual thin sample. Multiple stress-wave reflections are taken into account, and so signal echoes do not represent a difficulty. An example is presented for a graphite fiber epoxy composite (Hercules AS/3501-6). Thus, the technique provides a direct method for continuous or intermittent monitoring of through-thickness attenuation of plate structures which may be subject to service structural degradation.

Lee, S. S.↗
NASA NTRS2006

Calibration Issues and Operating System Requirements for Electron-Probe Microanalysis

Instrument purchase requirements and dialogue with manufacturers have established hardware parameters for alignment, stability, and reproducibility, which have helped improve the precision and accuracy of electron microprobe analysis (EPMA). The development of correction algorithms and the accurate solution to quantitative analysis problems requires the minimization of systematic errors and relies on internally consistent data sets. Improved hardware and computer systems have resulted in better automation of vacuum systems, stage and wavelength-dispersive spectrometer (WDS) mechanisms, and x-ray detector systems which have improved instrument stability and precision. Improved software now allows extended automated runs involving diverse setups and better integrates digital imaging and quantitative analysis. However, instrumental performance is not regularly maintained, as WDS are aligned and calibrated during installation but few laboratories appear to check and maintain this calibration. In particular, detector deadtime (DT) data is typically assumed rather than measured, due primarily to the difficulty and inconvenience of the measurement process. This is a source of fundamental systematic error in many microprobe laboratories and is unknown to the analyst, as the magnitude of DT correction is not listed in output by microprobe operating systems. The analyst must remain vigilant to deviations in instrumental alignment and calibration, and microprobe system software must conveniently verify the necessary parameters. Microanalysis of mission critical materials requires an ongoing demonstration of instrumental calibration. Possible approaches to improvements in instrument calibration, quality control, and accuracy will be discussed. Development of a set of core requirements based on discussions with users, researchers, and manufacturers can yield documents that improve and unify the methods by which instruments can be calibrated. These results can be used to continue improvements of EPMA.

Carpenter, P.↗