SEARCH · Search NASA

Results for “part”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS2022

Employing Relaxed Smoothness Constraints on Imaginary Part of Refractive Index in AERONET Aerosol Retrieval Algorithm

In the Aerosol Robotic Network (AERONET) retrieval algorithm, smoothness constraints on the imaginary part of the refractive index provide control of retrieved spectral dependence of aerosol absorption by preventing the inversion code from fitting the noise in optical measurements and thus avoiding unrealistic oscillations of retrievals with wavelength. The history of implementation of the smoothness constraints in the AERONET retrieval algorithm is discussed. It is shown that the latest version of the smoothness constraints on the imaginary part of refractive index, termed standard and employed by Version 3 of the retrieval algorithm, should be modified to account for strong variability of light absorption by brown-carbon-containing aerosols in UV through mid-visible parts of the solar spectrum. In Version 3 strong spectral constraints were imposed at high values of the Ångström exponent (440–870 nm) since black carbon was assumed to be the primary absorber, while the constraints became increasingly relaxed as aerosol exponent deceased to allow for wavelength dependence of absorption for dust aerosols. The new version of the smoothness constraints on the imaginary part of the refractive index assigns different weights to different pairs of wavelengths, which are the same for all values of the Ångström exponent. For example, in the case of four-wavelength input, the weights assigned to short-wavelength pairs (440–675, 675–870 nm) are small so that smoothness constraints do not suppress natural spectral variability of the imaginary part of the refractive index. At longer wavelengths (870–1020 nm), however, the weight is 10 times higher to provide additional constraints on the imaginary part of refractive index retrievals of aerosols with a high Ångström exponent due to low sensitivity to aerosol absorption for longer channels at relatively low aerosol optical depths. The effect of applying the new version of smoothness constraints, termed relaxed, on retrievals of single-scattering albedo is analyzed for case studies of different aerosol types: black- and brown-carbon-containing fine mode aerosols, mineral dust coarse mode aerosols, and urban industrial fine mode aerosol. It is shown that for brown-carbon-containing aerosols employing the relaxed smoothness constraints resulted in significant reduction in retrieved single-scattering albedo and spectral residual errors (compared to standard) at the short wavelengths. For example, biomass burning smoke cases showed a reduction in single-scattering albedo and spectral residual error at 380 nm of ∼ 0.033 and ∼ 17 %, respectively, for the Rexburg site and ∼ 0.04 and ∼ 12.7 % for the Rimrock site, both AERONET sites in Idaho, USA. For a site with very high levels of black-carbon-containing aerosols (Mongu, Zambia), the effect of modification in the smoothness constraints was minor. For mineral dust aerosols at small Ångström exponent values (Mezaira site, UAE), the spectral constraint on the imaginary part of the refractive index was already relaxed in Version 3; therefore the new relaxed constraint results in minimal change. In the case of weakly absorbing urban industrial aerosols at the GSFC site, there are significant changes in retrieved single-scattering albedo using relaxed assumption, especially reductions at longer wavelengths: ∼ 0.016 and ∼ 0.02 at 875 and 1020 nm, respectively, for 440 nm aerosol optical depth (AOD) ∼ 0.3. The modification of smoothness constraints on the imaginary part of the refractive index has a minor effect on retrievals of other aerosol parameters such as the real part of the refractive index and parameters of the aerosol size distribution. The implementation of the relaxed smoothness constraints on the imaginary part of the refractive index in the next version of the AERONET inversion algorithm will produce significant impacts at some sites in short wavelength channels (380 and 440 nm) for some biomass burning smoke cases with significant brown carbon content and possibly in mid-visible channels (500 and 675 nm) to near-infrared channels (870 to 1020 nm) for some urban industrial aerosol types. However, most differences in single-scattering albedo retrievals between those applying the new relaxed constraint and the standard constraint will be within the uncertainty of the single-scattering albedo retrievals, depending on the level of aerosol optical depth, Ångström exponent, brown carbon content and wavelength.

Aliaksandr Siniuk↗

DOE OSTI2020

Correlation of SWIR imaging with LPBF 304L stainless steel part properties

In the Laser Powder Bed Fusion (LPBF) process, the local thermal history can vary significantly over a part as the heat transfer characteristics and the laser scan path are geometry dependent. The variations introduce the potential for defects that lead to part failure, some of which are difficult to identify non-destructively with common ex-situ evaluation techniques. These defects include significant microstructural and mechanical property differences in the part interiors. In this paper, thermal features are extracted from in-situ Short-Wave Infrared (SWIR) imaging measurements to compile voxel based part representations and understand how the complexities in the thermal history affect part performance. The deviations in thermal features due to different laser processing parameters and complex scan pathing are explored. Empirical correlations are developed to map thermal features with the engineering properties (bulk yield strength, area percentage porosity, and local state) of 304L stainless steel parts manufactured by LPBF. Processing modes (insufficient melting and keyholing) are determined by mapping part property measurements with multiple thermal features. Generating the relationships between thermographic measurements and resulting SLM part properties lays the foundation for in-situ part qualification.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Build Orientation Dependent Microstructure in Polymer Laser Sintering: Relationship to Part Performance and Evolution with Aging

Laser sintering (LS) is widely used to produce functional polymeric parts; however, the resulting parts are often limited by their porous structure, and performance of the part may be strongly anisotropic. Relating the structural features of parts to build process conditions or powder feedstock has been explored previously. In contrast, little is known regarding how the unique internal structures of LS parts evolve and relate to their performance later in their life cycle, for example, after use in a real-world operating environment. In this study, a tightly controlled LS build process and measurement campaign by standard X-ray computed tomography (XCT), supported by high-resolution synchrotron XCT, was used to benchmark the internal microstructure (e.g. porosity) as a function of four different build orientations in printed polyamide-12 (PA-12) parts. The initial performance of the parts after printing was characterized by tensile testing and dynamic mechanical analysis (DMA). Arrays of PA-12 parts in different build orientations were exposed to steam (under pressure) and air across multiple temperature and time points for the purposes of accelerated aging through oxidative and hydrolytic breakdown. Exposing parts to steam dramatically altered the internal microstructure and functional properties such as the glass transition temperature, tensile properties, and damping behavior. Notably, post-aging XCT revealed large microstructural changes after only 40 h of steam treatment relative to the as-printed specimens. Furthermore, pore reorganization and changes in crystallinity occurred regardless of whether the steam temperature was aggressive enough to induce a significant loss in mechanical properties. The build orientation dependence on the aging rate was minimal with the relative trend in performance persisting across most metrics among the different orientations even after aging.

36 MATERIALS SCIENCE↗

DOE OSTI2022

In situ laser profilometry for material segmentation and digital reconstruction of a multicomponent additively manufactured part

In addition to its ability to produce geometrically complex parts, additive manufacturing offers a unique opportunity to collect data about a component while it is being fabricated. However, there has only been limited effort to characterize parts morphologically and compositionally in situ. In this article, we present a layer-by-layer, laser profilometry-based in situ characterization technique as a method to digitally reconstruct a multi-material part. Data collected by the laser profilometer yields height maps and grayscale images which are voxelized using purpose-built software to volumetrically reconstruct the part. Additionally, the same part was also analyzed using X-ray computed tomography (CT) which was not able to resolve the different compositional regions within the part, but captured the filament morphology. The part was then bisected to compare the digital reconstruction to the actual part morphology and composition. Overall, the digital reconstruction was in good agreement with both the CT and bisected images. Deviations between the digital reconstruction and the CT/bisected images are likely the result of image segmentation settings or material shifts after data was collected. The in situ characterization method demonstrated here sets the stage for real time process monitoring and paves the way for additively manufactured parts that are “born qualified.”

36 MATERIALS SCIENCE↗

DOE OSTI2021

Next Generation Co-Molded One-Piece Automotive Parts

The purpose of this project was to determine the feasibility of co-molding Class A Sheet Molding Compound (SMC), structural SMC, and continuous fiber prepreg materials to produce a single piece co-molded automotive part, such as a hood. The combination of the three molding materials and the incorporation of selective design features (ribs, flanges, corrugations) was expected to eliminate the need for inner reinforcement panels, significantly reducing tooling costs and simplifying the manufacturing process. A multi-material solution would also result in significant weight savings. The scope of this project included the material characterization of the three materials, development of cure and flow simulation models, and validation of the models against parts molded with different combinations of the materials on an 11”x11” plaque tool with rib features. The intent of this project was to apply the learnings obtained from co-molding a part with simplified geometry to a Phase 2 project that would produce a single piece hood, co-molded with the same materials. Resins from INEOS Composites were provided to IDI to produce SMC and continuous fiber prepregs. Purdue University and INEOS Composites characterized the rheological and curing behavior of the different materials as well as the mechanical properties of the co-molded parts. This data was used by Purdue University to create simulation models. Models were created to predict both flow patterns and predict mechanical properties of different laminate constructions in and around the ribs. Michigan State University - Corktown validated Purdue’s models by co-molding the three materials in different combinations on a tool containing rib features provided by Century Tool. The co-molded parts were evaluated against the simulation models by Purdue, Corktown and INEOS. The project team demonstrated the following: • The ability to obtain a cohesive co-molded structure made up of Class A SMC, Structural SMC, and continuous fiber prepreg. • The ability to obtain a co-molded part with a Class A surface • Modeling of flow and fiber orientation • Modeling to predict mechanical properties of multi-material co-molded structures The predicted flow behavior and fiber orientation from simulations were then compared with the molded samples. Exact local orientation state was difficult to compare between microscopy and flow simulation, but captured general trends. Multi-material flow behavior was generally modeled well with SMC materials, but the introduction of woven material sheets requires further model development. Purdue compared the predicted versus actual mechanical properties, and INEOS Composites evaluated the surface appearance of unpainted and painted co-molded parts. The models developed by Purdue demonstrated that the mechanical properties can be predicted for parts with varying material configurations. The resulting models can be applied to future co-molded part design, tooling design, and molding conditions.

36 MATERIALS SCIENCE↗

NASA NTRS1963

Space Flight Handbooks. Volume 3- Planetary Flight Handbook: Supplementary Trajectory Data: Venus to Earth and Mars to Earth - Part 2

Parts 2 and 3 present tabulations of trajectory data for scheduling flights to and from Venus and Mars during the period 1960-2000. Part 2 contains information for outbound flights to these planets; Part 3 contains information for trajectories returning from the planets to Earth. Each Part contains data for single-plane transfers, as well as for broken-plane transfers which employ a midcourse plane-change to eliminate the high speed "ridges." The mathematical analyses employed for all calculations are described in Part 1 of this handbook. To facilitate the construction of round-trip trajectories, the date at the target planet is held fixed while the trip duration is varied in 10-day increments from zero days to the length of that planet's synodic period with Earth. Dates of arrival at the target planet are presented in the extreme right-hand column of Part 2, and dates of departure from the target planet are presented in the extreme left-hand column of Part 3. Thus, by holding Part 2 directly to the left of Part 3, the analyst may easily and rapidly scan all trip possibilities which involve any desired stopover time at the target planet. Within approximately 200 days of each conjunction or opposition, data are presented in 10-day increments at the target planet. Only those trips are listed for which the hyperbolic excess speeds at either or both ends of the trajectory do not exceed 0.6 EMOS (Earth Mean Orbital Speed). For the remaining mission regions, the requirements are so smoothly varying that a 50-day interval in dates at the target planet may be employed; the 10-day interval in trip times is, however, preserved here. In these regions, only those trips are listed for which either or both speeds do not exceed 0.3 EMOS.

INTERPLANETARY FLIGHT↗

NASA NTRS1963

Space Flight Handbooks. Volume 3- Planetary Flight Handbook: Supplementary Trajectory Data: Venus to Earth and Mars to Earth - Part 3

Source record↗

DOE OSTI2022

A universal method to compare parts from STEP files

Abstract Model Based Definition (MBD) captures the complete specification of a part in digital form and leverages (at least) the universal “Standard for the Exchange of Product” (STEP) file format. MBD has revolutionized manufacturing due to time and cost savings associated with containing all engineering data within a single digital source. This work presents a novel method to transform digital definitions in any given STEP file into a tensor-like structure that is unique for each part and can be used to regenerate the original STEP file completely. Resulting STEP tensors are amenable to part comparison based on various part specifications in a general and straightforward manner. Here, part similarity is evaluated among sets of parts according to specific geometry, material composition, and design intent. Importantly, specification similarity can be quantified using only the tensors’ structure. As such, this approach is not limited to families of geometric shapes, part types, or fabrication methods; nor does it require any prior knowledge about the parts being compared.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Data for: Ultrasonic characterization of material heterogeneities in stainless steel parts fabricated by powder bed fusion

These are the raw ultrasonic waveform files and nanoindentation measurements for three additively manufactured 316L stainless steel components with different fabrication parameters. Each part's length is divided into four segmented regions where their fabrication energy densities change. Part V+ begins at 33 J/mm^3 and increases in energy density by 3 J/mm^3 with each segment. Part C remains at a constant 33 J/mm^3 throughout the part. Part V- begins at 33 J/mm^3 and decreases in energy density by 3 J/mm^3 with each segment. We have found that the ultrasonic waves in regions with higher energy densities will traverse more quickly, as shown by the shorter time of flight, and vice versa. Similarly, nanoindentation measurements of reduced modulus and hardness follow this trend. We have measured the direction in which the parts were fabricated (build direction) and the segmented regions that are perpendicular to the build direction (transverse directions). The build direction longitudinal wave velocity measurements are considerably lower than their transverse direction counterparts, indicating anisotropy between the two directions. In Part C, we have removed material from one of its surfaces and recorded its ultrasonic and nanoindentation measurements with each material removal iteration. Changes in the material properties are more prominent by nanoindentation, suggesting material heterogeneity between the part's surface and interior. The README.txt file has information on how to navigate the files and process the data.

Anisotropy↗

NASA NTRS1985

Rotor instability due to loose rotating part

Loosening of a rotating part from its fixed position on the shaft or a part of the stator which comes loose and begins to turn with the rotor very frequently represents machinery malfunction. The loose part becomes involved in rotative motion mostly due to dry or fluid friction, and thus its motion is very erratic. The loose part can also move axially along the shaft. Detachment of the rotating part causes changes in the rotor balance state. Most often this results in higher unbalance. During steady-state operation the effect of a loose rotating part can manifest itself through heat vibration. It can be diagnosed by observing periodic changes of amplitude and phase of the synchronous response. During start-up (or shutdown) a loose rotating part carrying some amount of unbalance may manifest its dynamic action in the form of subsynchronous vibrations, very similar to those of other instabilities. The objective of this demonstration is to observe the effect of a loose rotating part (fixed, however, in the axial direction) under both steady-state (rotor constant speed) and transient (rotor start-up or shutdown) operation. The dynamic response depends very much on the amount of damping in the system: lubrication of the loose part/shaft surfaces and addition/elimination of aerodynamic drag blades, mounted on the loose disk, significantly change the rotor response.

Muszynska, A.↗

NASA NTRS1989

Electrical, Electronic, and Electromechanical (EEE) parts management and control requirements for NASA space flight programs

This document establishes electrical, electronic, and electromechanical (EEE) parts management and control requirements for contractors providing and maintaining space flight and mission-essential or critical ground support equipment for NASA space flight programs. Although the text is worded 'the contractor shall,' the requirements are also to be used by NASA Headquarters and field installations for developing program/project parts management and control requirements for in-house and contracted efforts. This document places increased emphasis on parts programs to ensure that reliability and quality are considered through adequate consideration of the selection, control, and application of parts. It is the intent of this document to identify disciplines that can be implemented to obtain reliable parts which meet mission needs. The parts management and control requirements described in this document are to be selectively applied, based on equipment class and mission needs. Individual equipment needs should be evaluated to determine the extent to which each requirement should be implemented on a procurement. Utilization of this document does not preclude the usage of other documents. The entire process of developing and implementing requirements is referred to as 'tailoring' the program for a specific project. Some factors that should be considered in this tailoring process include program phase, equipment category and criticality, equipment complexity, and mission requirements. Parts management and control requirements advocated by this document directly support the concept of 'reliability by design' and are an integral part of system reliability and maintainability. Achieving the required availability and mission success objectives during operation depends on the attention given reliability and maintainability in the design phase. Consequently, it is intended that the requirements described in this document are consistent with those of NASA publications, 'Reliability Program Requirements for Aeronautical and Space System Contractors,' NHB 5300.4(1A-l); 'Maintainability Program Requirements for Space Systems,' NHB 5300.4(1E); and 'Quality Program Provisions for Aeronautical and Space System Contractors,' NHB 5300.4(1B).

Source record↗

NASA NTRS2000

NASA Parts Selection List (NPSL) WWW Site http://nepp.nasa.gov/npsl

The NASA Parts Selection List (NPSL) is an on-line resource for electronic parts selection tailored for use by spaceflight projects. The NPSL provides a list of commonly used electronic parts that have a history of satisfactory use in spaceflight applications. The objective of this www site is to provide NASA projects, contractors, university experimenters, et al with an easy to use resource that provides a baseline of electronic parts from which designers are encouraged to select. The NPSL is an ongoing resource produced by Code 562 in support of the NASA HQ funded NASA Electronic Parts and Packaging (NEPP) Program. The NPSL is produced as an electronic format deliverable made available via the referenced www site administered by Code 562. The NPSL does not provide information pertaining to patented or proprietary information. All of the information contained in the NPSL is available through various other public domain resources such as US Military procurement specifications for electronic parts, NASA GSFC's Preferred Parts List (PPL-21), and NASA's Standard Parts List (MIL-STD975).

Brusse, Jay↗

NASA NTRS2011

High Voltage EEE Parts for EMA/EHA Applications on Manned Launch Vehicles

The objective of this paper is an assessment of high voltage electronic components required for high horsepower electric thrust vector control (TVC) systems for human spaceflight launch critical application. The scope consists of creating of a database of available Grade 1 electrical, electronic and electromechanical (EEE) parts suited to this application, a qualification path for potential non-Grade 1 EEE parts that could be used in these designs, and pathfinder testing to validate aspects of the proposed qualification plan. Advances in the state of the art in high power electric power systems enable high horsepower electric actuators, such as the electromechnical actuator (EMA) and the electro-hydrostatic actuator (EHA), to be used in launch vehicle TVC systems, dramaticly reducing weight, complexity and operating costs. Designs typically use high voltage insulated gate bipolar transistors (HV-IGBT). However, no Grade 1 HV-IGBT exists and it is unlikely that market factors alone will produce such high quality parts. Furthermore, the perception of risk, the lack of qualification methodoloy, the absence of manned space flight heritage and other barriers impede the adoption of commercial grade parts onto the critical path. The method of approach is to identify high voltage electronic component types and key parameters for parts currently used in high horsepower EMA/EHA applications, to search for higher quality substitutes and custom manufacturers, to create a database for these parts, and then to explore ways to qualify these parts for use in human spaceflight launch critical application, including grossly derating and possibly treating hybrid parts as modules. This effort is ongoing, but results thus far include identification of over 60 HV-IGBT from four manufacturers, including some with a high reliability process flow. Voltage ranges for HV-IGBT have been identified, as has screening tests used to characterize HV-IGBT. BSI BS ISO 21350 Space systems Off-the-shelf item utilization, developed from Marshall Work Instruction MWI8060.1 OFF-THE-SHELF HARDWARE UTILIZATION IN FLIGHT HARDWARE DEVELOPMENTwas found to provide guidance for including commercial off-the-shelf (COTS) hardware for use in critical applications.

Griffin, Trent↗

DOE OSTI2024

DNA parts and gene constructs for plant biodesign

Plant biodesign requires the knowledge of DNA parts (e.g., genes, promoters, terminators), along with their combinations (as gene constructs) linked to engineered traits. DNA parts with validated or predicted functions in plants have been deposited in various online databases. However, these existing databases focus on basic biological functions of individual DNA parts, leaving a gap between basic knowledge and bioengineering applications. To fill this knowledge gap, we have created a user-friendly, open-ended database as a knowledge graph linking DNA parts to gene constructs to traits. This database contains experimentally validated DNA parts and gene constructs documented in peer-reviewed publications. The DNA parts include 1) molecular components with biological functions, such as genes involved in various biological processes (e.g., metabolic and signal transduction pathways) and 2) molecular components with technical functions, such as gene expression, genome engineering and sequence splicing. The gene constructs deposited in this database include both single-gene and multi-gene constructs. This database allows users to submit DNA parts and gene construct compositions linked to engineered traits described in peer-reviewed publications, providing a public digital repository for sharing the biodesign information among the researchers in the fields of plant biotechnology and plant synthetic biology.

plant biodesign synthetic biology gene constructs ↗

NASA NTRS1927

Method of Correcting Wind Tunnel Data for Omitted Parts of Airplane Models

Wind tunnel models do not have complete similarity to the full scale airplane. Part of the dissimilarity is due to the difference between the stationary model in the artificial wind stream of the tunnel and the moving airplane in still air. There are a number of other reasons for departing from exact geometrical similitude. For reasons of accuracy and economy, all minor parts of the full scale airplane, such as struts, wires, fittings, control horns and other parts whose scale corrections are large are removed from wind tunnel models. By omitting the minor parts of the airplane in the wind tunnel model and adding to the forces and moments of the model those omitted parts measured full scale and properly reduced, the scale effects of such parts disappear from the model data. Scale effects due to major parts of the airplane, particularly the fuselage and wings, can be corrected by omitting the propeller and making the surface of the model as smooth as possible, two further departures from geometrical similitude between model and full scale that add considerably to the accuracy and economy of model tests.

Smith, R H↗

NASA NTRS1997

Database Development for Electrical, Electronic, and Electromechanical (EEE) Parts for the International Space Station Alpha

More effective electronic communication processes are needed to transfer contractor and international partner data into NASA and prime contractor baseline database systems. It is estimated that the International Space Station Alpha (ISSA) parts database will contain up to one million parts each of which may require database capabilities for approximately one thousand bytes of data for each part. The resulting gigabyte database must provide easy access to users who will be preparing multiple analyses and reports in order to verify as-designed, as-built, launch, on-orbit, and return configurations for up to 45 missions associated with the construction of the ISSA. Additionally, Internet access to this data base is strongly indicated to allow multiple user access from clients located in many foreign countries. This summer's project involved familiarization and evaluation of the ISSA Electrical, Electronic, and Electromechanical (EEE) Parts data and the process of electronically managing these data. Particular attention was devoted to improving the interfaces among the many elements of the ISSA information system and its global customers and suppliers. Additionally, prototype queries were developed to facilitate the identification of data changes in the data base, verifications that the designs used only approved parts, and certifications that the flight hardware containing EEE parts was ready for flight. This project also resulted in specific recommendations to NASA for further development in the area of EEE parts database development and usage.

Wassil-Grimm, Andrew D.↗

NASA NTRS1998

A Conceptual Approach to Assimilating Remote Sensing Data to Improve Soil Moisture Profile Estimates in a Surface Flux/Hydrology Model: Overview - Part 1

Knowledge of the amount of water in the soil is of great importance to many earth science disciplines. Soil moisture is a key variable in controlling the exchange of water and energy between the land surface and the atmosphere. Thus, soil moisture information is valuable in a wide range of applications including weather and climate, runoff potential and flood control, early warning of droughts, irrigation, crop yield forecasting, soil erosion, reservoir management, geotechnical engineering, and water quality. Despite the importance of soil moisture information, widespread and continuous measurements of soil moisture are not possible today. Although many earth surface conditions can be measured from satellites, we still cannot adequately measure soil moisture from space. Research in soil moisture remote sensing began in the mid 1970s shortly after the surge in satellite development. Recent advances in remote sensing have shown that soil moisture can be measured, at least qualitatively, by several methods. Quantitative measurements of moisture in the soil surface layer have been most successful using both passive and active microwave remote sensing, although complications arise from surface roughness and vegetation type and density. Early attempts to measure soil moisture from space-borne microwave instruments were hindered by what is now considered sub-optimal wavelengths (shorter than 5 cm) and the coarse spatial resolution of the measurements. L-band frequencies between 1 and 3 GHz (10-30 cm) have been deemed optimal for detection of soil moisture in the upper few centimeters of soil. The Electronically Steered Thinned Array Radiometer (ESTAR), an aircraft-based instrument operating a 1,4 GHz, has shown great promise for soil moisture determination. Initiatives are underway to develop a similar instrument for space. Existing space-borne synthetic aperture radars (SARS) operating at C- and L-band have also shown some potential to detect surface wetness. The advantage of radar is its much higher resolution than passive microwave systems, but it is currently hampered by surface roughness effects and the lack of a good algorithm based on a single frequency and single polarization. In addition, its repeat frequency is generally low (about 40 days). In the meantime, two new radiometers offer some hope for remote sensing of soil moisture from space. The Tropical Rainfall Measuring Mission (TRMM) Microwave Imager (TMI), launched in November 1997, possesses a 10.65 GHz channel and the Advanced Microwave Scanning Radiometer (AMSR) on both the ADEOS-11 and Earth Observing System AM-1 platforms to be launched in 1999 possesses a 6.9 GHz channel. Aside from issues about interference from vegetation, the coarse resolution of these data will provide considerable challenges pertaining to their application. The resolution of TMI is about 45 km and that of AMSR is about 70 km. These resolutions are grossly inconsistent with the scale of soil moisture processes and the spatial variability of factors that control soil moisture. Scale disparities such as these are forcing us to rethink how we assimilate data of various scales in hydrologic models. Of particular interest is how to assimilate soil moisture data by reconciling the scale disparity between what we can expect from present and future remote sensing measurements of soil moisture and modeling soil moisture processes. It is because of this disparity between the resolution of space-based sensors and the scale of data needed for capturing the spatial variability of soil moisture and related properties that remote sensing of soil moisture has not met with more widespread success. Within a single footprint of current sensors at the wavelengths optimal for this application, in most cases there is enormous heterogeneity in soil moisture created by differences in landcover, soils and topography, as well as variability in antecedent precipitation. It is difficult to interpret the meaning of 'mean' soil moisture under such conditions and even more difficult to apply such a value. Because of the non-linear relationships between near-surface soil moisture and other variables of interest, such as surface energy fluxes and runoff, mean soil moisture has little applicability at such large scales. It is for these reasons that the use of remote sensing in conjunction with a hydrologic model appears to be of benefit in capturing the complete spatial and temporal structure of soil moisture. This paper is Part I of a four-part series describing a method for intermittently assimilating remotely-sensed soil moisture information to improve performance of a distributed land surface hydrology model. The method, summarized in section II, involves the following components, each of which is detailed in the indicated section of the paper or subsequent papers in this series: Forward radiative transfer model methods (section II and Part IV); Use of a Kalman filter to assimilate remotely-sensed soil moisture estimates with the model profile (section II and Part IV); Application of a soil hydrology model to capture the continuous evolution of the soil moisture profile within and below the root zone (section III); Statistical aggregation techniques (section IV and Part II); Disaggregation techniques using a neural network approach (section IV and Part III); and Maximum likelihood and Bayesian algorithms for inversely solving for the soil moisture profile in the upper few cm (Part IV).

Crosson, William L.↗

NASA NTRS2005

Automated Rapid Prototyping of 3D Ceramic Parts

An automated system of manufacturing equipment produces three-dimensional (3D) ceramic parts specified by computational models of the parts. The system implements an advanced, automated version of a generic rapid-prototyping process in which the fabrication of an object having a possibly complex 3D shape includes stacking of thin sheets, the outlines of which closely approximate the horizontal cross sections of the object at their respective heights. In this process, the thin sheets are made of a ceramic precursor material, and the stack is subsequently heated to transform it into a unitary ceramic object. In addition to the computer used to generate the computational model of the part to be fabricated, the equipment used in this process includes: 1) A commercially available laminated-object-manufacturing machine that was originally designed for building woodlike 3D objects from paper and was modified to accept sheets of ceramic precursor material, and 2) A machine designed specifically to feed single sheets of ceramic precursor material to the laminated-object-manufacturing machine. Like other rapid-prototyping processes that utilize stacking of thin sheets, this process begins with generation of the computational model of the part to be fabricated, followed by computational sectioning of the part into layers of predetermined thickness that collectively define the shape of the part. Information about each layer is transmitted to rapid-prototyping equipment, where the part is built layer by layer. What distinguishes this process from other rapid-prototyping processes that utilize stacking of thin sheets are the details of the machines and the actions that they perform. In this process, flexible sheets of ceramic precursor material (called "green" ceramic sheets) suitable for lamination are produced by tape casting. The binder used in the tape casting is specially formulated to enable lamination of layers with little or no applied heat or pressure. The tape is cut into individual sheets, which are stacked in the sheet-feeding machine until used. The sheet-feeding machine can hold enough sheets for about 8 hours of continuous operation.

McMillin, Scott G.↗