Search NASA⌕ Search

SEARCH · Search NASA

Results for “passivation layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Control of turbulence through a row of Helmholtz resonators

The manipulation of turbulent boundary layers is useful in a variety of situations including drag reduction and separation delay. In this study a passive method of altering the turbulence in a boundary layer is investigated. Ten Helmholtz resonators were imbedded in a spanwise row under a turbulent boundary layer. At certain airspeeds the resonators were strongly excited by the turbulence. In turn, the resonator motions interact to modify the turbulence and mean velocity profiles in the boundary layer. Tests were conducted to measure the response of the resonators as a function of freestream speed. Additional tests, conducted at the conditions for maximum response, documented the affect on the mean and turbulent velocity profiles.

Panton, Ronald L.↗
NASA NTRS1990

Numerical simulation of the control of the three-dimensional transition process in boundary layers

Surface heating techniques to control the three-dimensional laminar-turbulent transition process are numerically investigated for a water boundary layer. The Navier-Stokes and energy equations are solved using a fully implicit finite difference/spectral method. The spatially evolving boundary layer is simulated. Results of both passive and active methods of control are shown for small amplitude two-dimensional and three-dimensional disturbance waves. Control is also applied to the early stages of the secondary instability process using passive or active control techniques.

Kral, L. D.↗
NASA NTRS2000

Continuing Measurements of CO2 Crystals with a Hand-Held 35 GHz Radiometer

In order to increase our knowledge of the Martian polar caps, an improved understanding of the behavior of both frozen H2O and CO2 in different parts of the electromagnetic spectrum is needed. The thermal microwave part of the spectrum has received relatively little attention compared to the visible and infrared wavelengths. A simple experiment to measure the brightness temperature of frozen CO2 was first performed in the winter of 1998 using a 35 GHz radiometer. in experiments performed during the winter of 1999 and 2000, passive microwave radiation emanating from within layers of manufactured CO2 (dry ice) crystals was again measured with a 35 GHz handheld radiometer. Both large (0.8 cm) and small (0.3 cm) cylindrical-shaped dry ice pellets, at a temperature of 197 K (-76 C), were measured. A 1 sq m plate of aluminum sheet metal was positioned beneath the dry ice so that microwave emissions from the underlying soil layers would be minimized. Non-absorbing foam was positioned around the sides of the plate in order to keep the dry ice in place and to assure that the incremental deposits were level. Thirty-five GHz measurements of this plate were made through the dry ice deposits in the following way. Layers of dry ice were built up and measurements were repeated for the increasing CO2 pack. First, 7 cm of large CO2 pellets were poured onto the sheet metal plate, then an additional 7 cm were added, and finally, 12 cm were added on top of the 14 cm base. Hand-held 35 GHz measurements were made each time the thickness of the deposit was increased. The same process was repeated for the smaller grain pellets. Furthermore, during the past winter, 35 GHz measurements were taken of a 25 kg (27 cm x 27 cm x 27 cm) solid cube Of CO2, which was cut in half and then re-measured. Additional information is contained in the original extended abstract.

Foster, J.↗
NASA NTRS2021

Status of the James Webb Space Telescope Mission

The James Webb Space Telescope ( Webb) is the largest space telescope realized to-date, with a 6.5 m segmented primary mirror that must be folded to fit within its Ariane 5 launcher fairing. This infrared telescope is passively cooled using a five-layer sunshield that will keep the optical telescope and its four science instruments in the shade throughout the lifetime of the mission in an L2 orbit. Webb's science instruments include near- and mid­ infrared imagers and spectrometers that cover the spectral range from 0.6-28.5 µm. The Webb mission has a long history with numerous first of its kind technology developments, ground support equipment innovations, and algorithmic characterization advances. This conference proceeding summarizes the technical progress over the past two years, from the Spacecraft Element environmental testing to the Observatory integration and testing, and the final Observatory test plans leading up to launch, on-orbit commissioning, and science operations.

Michael W McElwain↗
NASA NTRS2001

The Estimation of Surface Latent Heat Flux over the Ocean and its Relationship to Marine Atmospheric Boundary Layer (MABL) Structure

A new technique combining active and passive remote sensing instruments for the estimation of surface latent heat flux over the ocean is presented. This synergistic method utilizes aerosol lidar backscatter data, multi-channel infrared radiometer data, and microwave scatterometer data acquired onboard the NASA P-313 research aircraft during an extended field campaign over the Atlantic ocean in support of the Lidar In-space Technology Experiment (LITE) in September of 1994. The 10 meter wind speed derived from scatterometers and lidar-radiometer inferred near-surface moisture are used to obtain an estimate of the surface flux of moisture via a bulk aerodynamic formula. The results are compared with the Special Sensor Microwave Imager (SSM/I) daily average latent heat flux and show reasonable agreement. However, the SSM/I values are biased low by about 15 W/sq m. In addition, the Marine Atmospheric Boundary Layer (MABL) height, entrainment zone thickness and integrated lidar backscatter intensity are computed from the lidar data and compared with the magnitude of the surface fluxes. The results show that the surface latent heat flux is most strongly correlated with entrainment zone depth, MABL height and the integrated MABL lidar backscatter, with corresponding correlation coefficients of 0.39, 0.43 and 0.71, respectively.

Palm, Stephen P.↗
NASA NTRS2000

Measurements in Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

Detailed velocity measurements were made along a flat plate subject to the same dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil. Reynolds numbers based on wetted plate length and nominal exit velocity were varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low and high inlet free-stream turbulence intensities (0.2% and 7%) were set using passive grids. The location of boundary-layer separation does not depend strongly on the free-stream turbulence level or Reynolds number, as long as the boundary layer remains non-turbulent prior to separation. Strong acceleration prevents transition on the upstream part of the plate in all cases. Both free-stream turbulence and Reynolds number have strong effects on transition in the adverse pressure gradient region. Under low free-stream turbulence conditions transition is induced by instability waves in the shear layer of the separation bubble. Reattachment generally occurs at the transition start. At Re = 50,000 the separation bubble does not close before the trailing edge of the modeled airfoil. At higher Re, transition moves upstream, and the boundary layer reattaches. With high free-stream turbulence levels, transition appears to occur in a bypass mode, similar to that in attached boundary layers. Transition moves upstream, resulting in shorter separation regions. At Re above 200,000, transition begins before separation. Mean velocity, turbulence and intermittency profiles are presented.

Volino, Ralph J.↗
NASA NTRS2010

L Band Brightness Temperature from Forest: Comparison of Approximate Techniques

In this paper, three approximate physical microwave radiometry models have been used to calculate brightness temperatures from a forest canopy at L-band. These models are (1) tau-omega model (zero order scattering approximation to radiative transfer equations), (2) successive order of scattering model up to first order (first order scattering approximation to the radiative transfer equations), and (3) Peak technique utilizing the active solution obtained from the Distorted Born Approximation (DBA). These models are physically-based and treat vegetation as a layer of discrete scatterers over a rough surface. Vegetation components within the canopy are represented by canonical shapes such as dielectric discs and cylinders. The tau-omega model is based on a zero-order solution to the radiative transfer (RT) equations. The model ignores scattering except for the effect of the scatterers in the attenuation of the emission through the vegetation. Application of the tau-omega model to data acquired during airborne and ground-based campaigns over the years has solidified scientific understanding of microwave interactions with different landscapes. In particular, shrubland, grasslands, agricultural crops, and light to moderate vegetation have been investigated. Its applicability to areas with a significant tree fraction is unknown. The first order scattering model is based on an iterative solution of the RT equation up to the first order. The first order solution is obtained by substituting the zeroth-order solution into the scattering source term and then solving the resulting radiative transfer equations. This formulation adds a new scattering term to the tau-omega model. It represents emission by particles in the layer and emission by the ground that is scattered once by particles in the layer. The resulting model represents an improvement over the standard zero-order solution (the tau-omega model) since it accounts for the scattered vegetation and ground radiation that can have a pronounced effect on the observed brightness temperature. The third model is based on the Peake formulation in conjunction with the DBA. The procedure for calculation of forest emission is accomplished by first calculating the bistatic scattering cross section for each type of scatterer, then by using the DBA to calculate specular albedo of the ground and the diffused albedo of the layer. Once the albedos are determined, Peake s principle relating active and passive problems can be used to determine the effective emissivity of the forest layer.

Kurum, Mehmet↗
NASA NTRS1999

The Estimation Surface Latent Heat Flux Over the Ocean and its Relationship to Marine Atmospheric Boundary Layer (MABL) Structure

A new technique combining active and passive remote sensing instruments for the estimation of surface latent heat flux over the ocean is presented. This synergistic method utilizes aerosol lidar backscatter data, multi-channel infrared radiometer data and microwave scatterometer data acquired onboard the NASA P-3B research aircraft during an extended field campaign over the Atlantic ocean in support of the Lidar In-space Technology Experiment (LITE) in September of 1994. The 10 meter wind speed derived from the scatterometers and the lidar-radiometer inferred near-surface moisture are used to obtain an estimate of the surface flux of moisture via bulk aerodynamic formulae. The results are compared with the Special Sensor Microwave Imager (SSM/I) daily average latent heat flux and show reasonable agreement. However, the SSM/I values are biased high by about 30 W/sq m. In addition, the MABL height, entrainment zone thickness and integrated lidar backscatter intensity are computed from the lidar data and compared with the magnitude of the surface fluxes. The results show that the surface latent heat flux is most strongly correlated with entrainment zone top, bottom and the integrated MABL lidar backscatter, with corresponding correlation coefficients of 0.62, 0.67 and 0.61, respectively.

Palm, Stephen P.↗
NASA NTRS2000

The Estimation of Surface Latent Heat Flux Over the Ocean and its Relationship to Marine Atmospheric Boundary Layer (MABL) Structure

A new technique combining active and passive remote sensing instruments for the estimation of surface latent heat flux over the ocean is presented. This synergistic method uses aerosol lidar backscatter data, multi-channel infrared radiometer data and microwave scatterometer data acquired onboard the NASA P-3B research aircraft during an extended field campaign over the Atlantic ocean in support of the Lidar In-space Technology Experiment (LITE) in September of 1994. The 10 meter wind speed derived from the scatterometers and the lidar-radiometer inferred near-surface moisture are used to obtain an estimate of the surface flux of moisture via bulk aerodynamic formulae. The results are compared with the Special Sensor Microwave Imager (SSM/I) daily average latent heat flux and show reasonable agreement with an rms error and bias of about 50 and 25 W per square meters, respectively. In addition, the MABL height, entrainment zone thickness and integrated lidar backscatter intensity are computed from the lidar data and compared with the magnitude of the surface fluxes. The results show that the surface latent heat flux is most strongly correlated with entrainment zone top, bottom and the integrated MABL lidar backscatter, with corresponding correlation coefficients of 0.62, 0.67 and 0.61, respectively.

Palm, Stephen P.↗
NASA NTRS2007

Design and Fabrication of High-Efficiency CMOS/CCD Imagers

An architecture for back-illuminated complementary metal oxide/semiconductor (CMOS) and charge-coupled-device (CCD) ultraviolet/visible/near infrared- light image sensors, and a method of fabrication to implement the architecture, are undergoing development. The architecture and method are expected to enable realization of the full potential of back-illuminated CMOS/CCD imagers to perform with high efficiency, high sensitivity, excellent angular response, and in-pixel signal processing. The architecture and method are compatible with next-generation CMOS dielectric-forming and metallization techniques, and the process flow of the method is compatible with process flows typical of the manufacture of very-large-scale integrated (VLSI) circuits. The architecture and method overcome all obstacles that have hitherto prevented high-yield, low-cost fabrication of back-illuminated CMOS/CCD imagers by use of standard VLSI fabrication tools and techniques. It is not possible to discuss the obstacles in detail within the space available for this article. Briefly, the obstacles are posed by the problems of generating light-absorbing layers having desired uniform and accurate thicknesses, passivation of surfaces, forming structures for efficient collection of charge carriers, and wafer-scale thinning (in contradistinction to diescale thinning). A basic element of the present architecture and method - the element that, more than any other, makes it possible to overcome the obstacles - is the use of an alternative starting material: Instead of starting with a conventional bulk-CMOS wafer that consists of a p-doped epitaxial silicon layer grown on a heavily-p-doped silicon substrate, one starts with a special silicon-on-insulator (SOI) wafer that consists of a thermal oxide buried between a lightly p- or n-doped, thick silicon layer and a device silicon layer of appropriate thickness and doping. The thick silicon layer is used as a handle: that is, as a mechanical support for the device silicon layer during micro-fabrication.

Pain, Bedabrata↗
NASA NTRS2021

Evaluation and Applications of Multi-Instrument Boundary-Layer Thermodynamic Retrievals

Recent reports have highlighted the need for improved observations of the boundary layer. In this study, we explore the combination of ground-based active and passive remote sensors deployed for thermodynamic profiling to analyze various boundary-layer observation strategies. Optimal-estimation retrievals of thermodynamic profiles from Atmospheric Emitted Radiance Interferometer (AERI) observed spectral radiance are compared with and without the addition of active sensor observations from a May–June 2017 observation period at the Atmospheric Radiation Measurement–Southern Great Plains Site. In all, three separate thermodynamic retrievals are considered here: retrievals including AERI data only, retrievals including AERI data and Vaisala water vapour differential absorption lidar data, and retrievals including AERI data and Raman lidar data. First, the three retrievals are compared to each other and to reference radiosonde data over the full observation period to get a bulk understanding of their differences and characterize the impact of clouds on these retrieved profiles. These analyses show that the most significant differences are in the water vapour field, where the active sensors are better able to represent the moisture gradient in the entrainment zone near boundary layer top. We also explore how differences in retrievals may impact results of applied analyses including land–atmosphere coupling, convection indices, and severe storm environmental characterization. Overall, adding active sensors to the optimal-estimation retrieval showed some added information, particularly in the moisture field. Given the costs of such platforms, the value of that added information must be weighed for the application at hand.

boundary-layer observation↗
NASA NTRS2011

What's on the Surface? Physics and Chemistry of Delta-Doped Surfaces

Outline of presentation: 1. Detector surfaces and the problem of stability 2. Delta-doped detectors 3. Physics of Delta-doped Silicon 4. Chemistry of the Si-SiO2 Interface 5. Physics and Chemistry of Delta-doped Surfaces a. Compensation b. Inversion c. Quantum exclusion. Conclusions: 1. Quantum confinement of electrons and holes dominates the behavior of delta-doped surfaces. 2. Stability of delta-doped detectors: Delta-layer creates an approx 1 eV tunnel barrier between bulk and surface. 3. At high surface charge densities, Tamm-Shockley states form at the surface. 4. Surface passivation by quantum exclusion: Near-surface delta-layer suppresses T-S trapping of minority carriers. 5. The Si-SiO2 interface compensates the surface 6. For delta-layers at intermediate depth, surface inversion layer forms 7. Density of Si-SiO2 interface charge can be extremely high (>10(exp 14)/sq cm)

detectors↗
NASA NTRS2018

The Feasibility of Detecting Supercooled Liquid with a Forward-Looking Radiometer

A three-dimensional radiative transfer model is utilized to determine the feasibility of a forward-viewing passive sensor for remotely detecting hazardous icing conditions. Wband ground-based radar simulations show no obvious ability to discriminate a cloud-top supercooled layer; however, the spectra for a forward-viewing passive sensor show a strong signal at two stand-off distances when compared with the clear sky spectrum. Such an instrument would be critical for manned and unmanned aircraft, particularly when size, weight, and power requirements restrict the installation of deicing equipment.

clouds↗
NASA NTRS1992

Multi-layer light-weight protective coating and method for application

A thin, light-weight, multi-layer coating is provided for protecting metals and their alloys from environmental attack at high temperatures. A reaction barrier is applied to the metal substrate and a diffusion barrier is then applied to the reaction barrier. A sealant layer may also be applied to the diffusion barrier if desired. The reaction barrier is either non-reactive or passivating with respect to the metal substrate and the diffusion barrier. The diffusion barrier is either non-reactive or passivating with respect to the reaction barrier and the sealant layer. The sealant layer is immiscible with the diffusion barrier and has a softening point below the expected use temperature of the metal.

Wiedemann, Karl E.↗
NASA NTRS2003

CLARAty Functional-Layer Software

Functional-layer software for the Coupled Layer Architecture for Robotics Autonomy (CLARAty) is being developed. [CLARAty was described in Coupled-Layer Architecture for Advanced Software for Robots (NPO-21218), NASA Tech Briefs, Vol. 26, No. 12 (December 2002), page 48. To recapitulate: CLARAty was proposed to improve the modularity of robotic software while tightening the coupling between planning/execution and control subsystems. Whereas prior robotic software architectures have typically contained three levels, the CLARAty architecture contains two layers: a decision layer and a functional layer.] Just as an operating system provides abstraction from computational hardware, the CLARAty functional-layer software provides for abstraction for the different robotic systems. The functional-layer software establishes interrelated, object-oriented hierarchies that contain active and passive objects that represent the different levels of system abstrations and components. The functional-layer software is decomposed into a set of reusable core components and a set of extended components that adapt the reusable set to specific hardware implementations. The reusable components (a) provide behavior and interface definitions and implementations of basic functionality, (b) provide local executive capabilities, (c) manage local resources, and (d) support state and resource queries by the decision layer. Software for robotic systems can be built by use of these components.

Nesnas, Issa↗
NASA NTRS1980

Surface effects on the microwave backscatter and emission of snow

Measurements were performed with active and passive microwave sensors for both dry and wet snow conditions. A layer of Rayleigh scatterers with irregular surface boundaries is found to be a reasonable model for interpreting passive and active measurements in X- and Ku-bands. It was found that roughness had a significant effect on both backscatter and emission from wet snow; however, only a small effect was noted for dry snow.

Fung, A. K.↗
NASA NTRS1981

Assessment of high temperature metallizations for I(2)L and CMOS technologies

High temperature barrier metallizations were assessed and tested for I(2)L and CMOS applications. Life tests were accelerated to 375 C in view of the -55 C to +300 C temperature range established for engine-located electronics without fuel cooling. The gold-refractory metallizations evaluated were Au-TiW-PtSi, Au-TiW/TiO2/TiW-PtSi and Au-TiW(N)-PtSi. These metallization systems were thermally annealed to at least 375 C for up to 250 hours. The critical requirement for stable diffusion barrier is the TiW grain size. Small grain (250A-500A) films were observed to be stable up to 375 C. Deposition to TiW diffusion barrier in the presence of oxygen and nitrogen also results in an effective diffusion barrier. Auger electron spectroscopy profiles of the PtSi indicates some penetration by the TiW. In the case of PtSi/TiW interface, the redistribution of oxygen further passivates the system by forming a TiO2 layer at the interface.

Christou, A.↗