Search NASA⌕ Search

SEARCH · Search NASA

Results for “point defect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Direct correlation and strong reduction of native point defects and microwave dielectric loss in air-annealed (Ba,Sr)TiO{sub 3}

We report on the native defect and microwave properties of 1 μm thick Ba{sub 0.50}Sr{sub 0.50}TiO{sub 3} (BST) films grown on MgO (100) substrates by molecular beam epitaxy (MBE). Depth-resolved cathodoluminescence spectroscopy (DRCLS) showed high densities of native point defects in as-deposited BST films, causing strong subgap emission between 2.0 eV and 3.0 eV due to mixed cation V{sub C} and oxygen Vo vacancies. Post growth air anneals reduce these defects with 2.2, 2.65, and 3.0 eV V{sub O} and 2.4 eV V{sub C} intensities decreasing with increasing anneal temperature and by nearly two orders of magnitude after 950 °C annealing. These low-defect annealed BST films exhibited high quality microwave properties, including room temperature interdigitated capacitor tunability of 13% under an electric bias of 40 V and tan δ of 0.002 at 10 GHz and 40 V bias. The results provide a feasible route to grow high quality BST films by MBE through post-air annealing guided by DRCLS.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Reduced photothermal heating in diamonds enriched with H3 point defects

Solid-state laser refrigeration of semiconductors remains an outstanding experimental challenge. In this work, we show that, following excitation with a laser wavelength of 532 nm, bulk diamond crystals doped with H3 centers both emit efficient up-conversion (anti-Stokes) photoluminescence and also show significantly reduced photothermal heating relative to crystals doped with nitrogen–vacancy (NV) centers. The H3 center in diamond is a highly photostable defect that avoids bleaching at high laser irradiances of 10–70 MW/cm 2 and has been shown to exhibit laser action, tunable over the visible band of 500–600 nm. Here, the observed reduction of photothermal heating arises due to a decrease in the concentration of absorbing point defects, including NV-centers. These results encourage future exploration of techniques for H3 enrichment in diamonds under high-pressure, high-temperature conditions for the simultaneous anti-Stokes fluorescence cooling and radiation balanced lasing in semiconductor materials. Reducing photothermal heating in diamond through the formation of H3 centers also opens up new possibilities in quantum sensing via optically detected magnetic resonance spectroscopy at ambient conditions.

42 ENGINEERING↗

Improving the Carrier Lifetime of Tin Sulfide via Prediction and Mitigation of Harmful Point Defects

Tin monosulfide (SnS) is an emerging thin-film absorber material for photovoltaics. An outstanding challenge is to improve carrier lifetimes to >1 ns, which should enable >10% device efficiencies. However, reported results to date have only demonstrated lifetimes at or below 100 ps. In this study, we employ defect modeling to identify the sulfur vacancy and defects from Fe, Co, and Mo as most recombination-active. We attempt to minimize these defects in crystalline samples through high-purity, sulfur-rich growth and experimentally improve lifetimes to >3 ns, thus achieving our 1 ns goal. This framework might prove effective for unlocking the lifetime potential in other emerging thin-film materials by rapidly identifying and mitigating lifetime-limiting point defects.

14 SOLAR ENERGY↗

Nanoscale interplay of native point defects near Sr-deficient SrxTiO 3 /SrTiO 3 interfaces

SrTiO 3 has many applications involving interfaces with other materials, but defects that affect the properties of SrTiO 3 films can also play a significant role at its heterointerfaces and even at junctions with nonstoichiometric SrTiO 3 . Depth-resolved cathodoluminescence spectroscopy (DRCLS) combined with systematic cation Sr content reduction in SrxTiO 3 ultrathin films grown on SrTiO 3 showed an interplay of native point defects and electronic structure within the Sr-deficient film and how interplay extends tens of nanometers into the substrate below. Understanding how defects form and affect interface electronic structure during epitaxial growth is central to improving complex oxide devices. Controlling the balance of oxygen vacancy defects with strontium vacancies and other acceptor-like defects can improve control over free carrier densities. Likewise, control over nanoscale defect charge distributions can advance new device features such as two-dimensional hole gases and the performance of existing devices such as ferroelectric tunnel junctions. This study shows how DRCLS directly measures the relative densities and spatial distributions of multiple native defects within and extending away from nanoscale SrxTiO 3 /SrTiO 3 junctions and how their interplay varies with controlled epitaxial growth. In turn, these growth-dependent defect variations can help guide SrTiO 3 epitaxial growth with other complex oxides.

36 MATERIALS SCIENCE↗

Effect of nickel on point defects diffusion in Fe – Ni alloys

Iron-Nickel alloys are perspective alloys as nuclear energy structural materials because of their good radiation damage tolerance and mechanical properties. Understanding of experimentally observed features such as the effect of Ni content to radiation defects evolution is essential for developing predictive models of radiation. Recently an atomic-scale modelling study has revealed one particular mechanism of Ni effect related to the reduced mobility of clusters of interstitial atoms in Fe-Ni alloys. In this paper we present results of the microsecond-scale molecular dynamics study of point defects, i.e. vacancies and self-interstitial atoms, diffusion in Fe-Ni alloys. It is found that the addition of Ni atoms affects diffusion processes: diffusion of vacancies is enhanced in the presence of Ni, whereas diffusion of interstitials is reduced and these effects increase at high Ni concentration and low temperature. As a result, the role of Ni solutes in radiation damage evolution in Fe-Ni alloys is discussed.

36 MATERIALS SCIENCE↗

Excited State Properties of Point Defects in Semiconductors and Insulators Investigated with Time-Dependent Density Functional Theory

Here, we present a formulation of spin-conserving and spin-flip hybrid time-dependent density functional theory (TDDFT), including the calculation of analytical forces, which allows for efficient calculations of excited state properties of solid-state systems with hundreds to thousands of atoms. We discuss an implementation on both GPU- and CPU-based architectures along with several acceleration techniques. We then apply our formulation to the study of several point defects in semiconductors and insulators, specifically the negatively charged nitrogen-vacancy and neutral silicon-vacancy centers in diamond, the neutral divacancy center in 4H silicon carbide, and the neutral oxygen-vacancy center in magnesium oxide. Our results highlight the importance of taking into account structural relaxations in excited states in order to interpret and predict optical absorption and emission mechanisms in spin defects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Point defect engineering strategies to suppress A-center formation in silicon

We investigate the impact of tin doping on the formation of vacancy-oxygen pairs (VO or A-centers) and their conversion to VO{sub 2} clusters in electron-irradiated silicon. The experimental results are consistent with previous reports that Sn doping suppresses the formation of the A-center. We introduce a model to account for the observed differences under both Sn-poor and Sn-rich doping conditions. Using density functional theory calculations, we propose point defect engineering strategies to reduce the concentration of the deleterious A-centers in silicon. We predict that doping with lead, zirconium, or hafnium will lead to the suppression of the A-centers.

36 MATERIALS SCIENCE↗

Quantifying point defects in Cu 2 ZnSn(S,Se) 4 thin films using resonant x-ray diffraction

Cu 2ZnSn(S,Se)4 is an interesting, earth abundant photovoltaic material, but has suffered from low open circuit voltage. To better understand the film structure, we have measured resonant x-ray diffraction across the Cu and Zn K-edges for the device quality thin films of Cu 2ZnSnS4 (8.6% efficiency) and Cu 2ZnSn(S,Se)4 (3.5% efficiency). This approach allows for the confirmation of the underlying kesterite structure and quantification of the concentration of point defects and vacancies on the Cu, Zn, and Sn sublattices. Rietveld refinement of powder diffraction data collected at multiple energies is used to determine that there exists a high level of Cu Zn and Zn Cu defects on the 2c and 2d Wyckoff positions. We observe a significantly lower concentration of Zn Sn defects and Cu or Zn vacancies.

14 SOLAR ENERGY↗

Role of Point Defects on the Reactivity of Reconstructed Anatase Titanium Dioxide (001) Surface

The chemical reactivity of different surfaces of titanium dioxide (TiO2) has been the subject of extensive studies in recent decades. The anatase TiO2(001) and its (1x4) reconstructed surfaces were theoretically considered to be the most reactive and have been heavily pursued by synthetic chemists. However, the lack of direct experimental verification or determination of the active sites on these surfaces has caused controversy and debate. Here we report a systematic study on an anatase TiO2(001)-(1x4) surface by means of microscopic and spectroscopic techniques in combination with first-principles calculations. Two types of intrinsic point defects are identified, among which only the Ti3+ defect site on the reduced surface demonstrates considerable chemical activity. The perfect surface itself can be fully oxidized, but shows no obvious activity. Our findings suggest that the reactivity of the anatase TiO2(001) surface should depend on its reduction status, similar to that of rutile TiO2 surfaces.

Environmental Molecular Sciences Laboratory↗

Point Defect Distributions in ZnSe Crystals: Effects of Gravity Vector Orientation during Physical Vapor Transport Growth

ZnSe crystals were grown by the physical vapor transport technique under horizontal and vertical (stabilized and destabilized) configurations. Secondary ion mass spectroscopy and photoluminescence measurements were performed on the ZnSe samples to map the distributions of [Si], [Fe], [Cu], [Al] and [Li or Na] impurities as well as Zn vacancy, [V(zn)]. The annealings of ZnSe under controlled Zn pressures were studied to correlate the measured photoluminescence emission intensity to the equilibrium Zn partial pressure. In the horizontal grown crystals the segregations of [Si], [Fe], [Al] and [V(zn)] along the gravity vector direction were observed whereas in the vertically stabilized grown crystal the segregations of these point defects were radially symmetrical. No apparent pattern was observed on the measured distributions in the vertically destabilized grown crystal. The observed segregations in the three growth configurations were interpreted based on the possible buoyancy-driven convection in the vapor phase.

Su, Ching-Hua↗

Point Defect Distributions in ZnSe Crystals: Effects of Gravity Vector Orientation During Physical Vapor Transport Growth

ZnSe crystals were grown by the physical vapor transport technique under horizontal and vertical (stabilized and destabilized) configurations. Secondary ion mass spectroscopy and photoluminescence measurements were performed on the grown ZnSe samples to map the distributions of [Si], [Fe], [Cu], [Al] and [Li or Na] impurities as well as Zn vacancy, [V (sub Zn)]. Annealings of ZnSe under controlled Zn pressures were studied to correlate the measured photoluminescence emission intensity to the equilibrium Zn partial pressure. In the horizontal grown crystals the segregations of [Si], [Fe], [Al] and [V (sub Zn)] were observed along the gravity vector direction whereas in the vertically stabilized grown crystal the segregation of these point defects was radially symmetrical. No apparent pattern was observed on the measured distributions in the vertically destabilized grown crystal. The observed segregations in the three growth configurations were interpreted based on the possible buoyancy-driven convection in the vapor phase.

Su, Ching-Hua↗

Stabilization of point-defect spin qubits by quantum wells

Defect-based quantum systems in wide bandgap semiconductors are strong candidates for scalable quantum-information technologies. However, these systems are often complicated by charge-state instabilities and interference by phonons, which can diminish spin-initialization fidelities and limit room-temperature operation. Here, we identify a pathway around these drawbacks by showing that an engineered quantum well can stabilize the charge state of a qubit. Using density-functional theory and experimental synchrotron X-ray diffraction studies, we construct a model for previously unattributed point defect centers in silicon carbide as a near-stacking fault axial divacancy and show how this model explains these defects' robustness against photoionization and room temperature stability. These results provide a materials-based solution to the optical instability of color centers in semiconductors, paving the way for the development of robust single-photon sources and spin qubits.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Modeling neutral defects in III-V ternary alloys with a special quasirandom structure: Analysis of As- and III-site point defects in InGaAs

While first-principles density functional theory modeling has become a vital tool to investigate defect properties in semiconductors, the lack of crystalline periodicity in pseudobinary random composition alloys, such as In 1−𝑥 ⁢Ga 𝑥 ⁢As, complicates such analyses. We present a simulation strategy to systematically take into account the variability in the local defect environment in order to predict statistical properties of neutral intrinsic defects in In 1−𝑥⁢ Ga 𝑥 ⁢As. We use a comprehensive sampling from a modest-sized 64-atom special quasirandom structure (SQS) to define a statistically representative set of defects, and use a 512-atom hypercell, a 2 × 2 × 2 supercell of SQS supercells, to achieve cell-size convergence. We articulate an equivalent site principle and describe how it constrains atomic chemical reference energies in computation of defect formation energies in pseudobinary alloys. A simple protocol for estimating reference energies for the Ga and In atoms sharing the III site succeeds in obtaining the equivalence of defects at Ga-sites and In sites in the SQS supercell, (<30 meV differences in average formation energies). For III-site defects, such as the As antisite As III , the statistical variability in formation energies is modest, ≈ 0.1–0.2 eV. The variability in formation energy at As-site defects, such as the As vacancy 𝑣 As , can be much larger, >1 eV. The As antisite is shown to be a low-energy defect and the most likely to be present in as-grown materials, just as in GaAs. All other defects are higher-energy defects unlikely to be important in native material, but potentially important in radiation-damaged material. With a strong variability in defect energies, especially on the As-site, explicit consideration of statistical variability due to compositional randomness will be imperative for meaningful and quantitative comparisons to experiment.

Density functional theory↗

Point Defects and Grain Boundaries in Rotationally Commensurate MoS 2 on Epitaxial Graphene

With reduced degrees of freedom, structural defects are expected to play a greater role in two-dimensional materials in comparison to their bulk counterparts. In particular, mechanical strength, electronic properties, and chemical reactivity are strongly affected by crystal imperfections in the atomically thin limit. Here, ultrahigh vacuum (UHV) scanning tunneling microscopy (STM) and spectroscopy (STS) are employed to interrogate point and line defects in monolayer MoS 2 grown on epitaxial graphene (EG) at the atomic scale. Five types of point defects are observed with the majority species showing apparent structures that are consistent with vacancy and interstitial models. The total defect density is observed to be lower than MoS 2 grown on other substrates and is likely attributed to the van der Waals epitaxy of MoS 2 on EG. Grain boundaries (GBs) with 30° and 60° tilt angles resulting from the rotational commensurability of MoS 2 on EG are more easily resolved by STM than atomic force microscopy at similar scales due to the enhanced contrast from their distinct electronic states. For example, band gap reduction to ~0.8 and ~0.5 eV is observed with STS for 30° and 60° GBs, respectively. In addition, atomic resolution STM images of these GBs are found to agree well with proposed structure models. In conclusion, this work offers quantitative insight into the structure and properties of common defects in MoS 2 and suggests pathways for tailoring the performance of MoS 2 /graphene heterostructures via defect engineering.

36 MATERIALS SCIENCE↗

First-principles study of He point-defects in HCP rare-earth metals

He defect properties in Sc, Y, Gd, Tb, Dy, Ho, Er and Lu were studied using first-principles calculations based on density functional theory. The results indicate that the formation energy of an interstitial He atom is smaller than that of a substitutional He atom in all hcp rare-earth metals considered. Furthermore, the tetrahedral interstitial position is more favorable than an octahedral position for He defects. The results are compared with those from bcc and fcc metals.

36 MATERIALS SCIENCE↗

Ab initio study of intrinsic, H and He point defects in hcp-Er

Ab initio calculations based on density functional theory have been performed to determine the properties of self-interstitial atoms (SIAs), vacancies, and single H and He atoms in hcp-Er. The results show that the most stable configuration for an SIA is a basal octahedral (BO) configuration, while the octahedral (O), basal split (BS) and crowdion (C) interstitial configurations are less stable, followed by the split <0001> dumbbell and tetrahedral configurations. For both H and He defects, the formation energy of an interstitial atom is less than that of a substitutional atom in hcp-Er. Furthermore, the tetrahedral interstitial position is more stable than an octahedral position for both He and H interstitials. The hybridization of the He and H defects with Er atoms has been used to explain the relative stabilities of these defects in hcp-Er.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Interaction Rates of Group-III and Group-V Impurities with Intrinsic Point Defects in Irradiated Si and Ge

A comparative study of interactions of shallow impurities with primary defects in oxygen- and carbon-lean moderately doped Si and Ge subjected to irradiation with 0.9 MeV electrons, {sup 60}Co gamma-rays, and 15 MeV protons at room temperature is presented and discussed. For the quantitative characterization of such interactions, changes in the total concentration of the original shallow group-V donor or group-III acceptor impurities in the irradiated materials are determined by Hall effect measurements over a wide temperature range. Losses of the shallow donor or acceptor states in the irradiated Si and Ge are indicative of their removal rates that can be used for estimation of production rates of primary defects interacting with the dopants. Some important factors affecting the interactions between primary defects and shallow impurities in Si and Ge are highlighted.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗