Search NASA⌕ Search

SEARCH · Search NASA

Results for “polymer physics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Photothermal degradation of ethylene/vinylacetate copolymer

Photothermal degradation studies were conducted on a 'stabilized' formulation of ethylene/vinyl acetate copolymer (EVA) in the temperature range 25-105 C under three different oxygen environments (in open air, with limited access to O2, and in a dark closed stagnant oven). These studies were performed in order to evaluate the utility of EVA as an encapsulation material for photovoltaic modules. Results showed that at low temperature (25 C), slow photooxidation of the polymer occurred via electronic energy transfer involving the UV absorber incorporated in the polymer. However, no changes in the physical properties of the bulk polymer were detected up to 1500 hours of irradiation. At elevated temperatures, leaching and evaporation of the additives occurred, which ultimately resulted in the chemical crosslinking of the copolymer and the formation of volatile photoproducts such as acetic acid.

Liang, R. H.↗
NASA NTRS1990

A brief survey of radiation effects on polymer dielectrics

Future space power needs are extrapolated to be at least three to four orders of magnitude more than is currently available. This long-term reliable power will be required on missions such as the Space Station, Pathfinder, Space Plane, and high-powered satellites, and for defense. Electrical insulation and dielectrics are the key electrical materials needed to support these power systems, where a single-point system failure could prove catastrophic or even fatal for the whole mission. Therefore, the impact of radiation, an environmental stress, on the properties and performance of insulation and dielectrics must be understood. The influence of radiation on polymer dielectrics, the insulating materials most commonly used for power transmission and storage, is reviewed. The effects of the type of radiation, dose, rate, and total exposure on the key electrical, mechanical, and physical properties of polymer dielectrics are described and explained.

Laghari, Javaid R.↗
DOE OSTI2020

Design of materials with supramolecular polymers

One hundred years ago Hermann Staudinger was strongly criticized by his scientific peers for his macromolecular hypothesis, but today it is hard to imagine a world without polymers. His hypothesis described polymers as macromolecules composed of large numbers of structural units connected by covalent bonds. In the 1990s the concept of supramolecular polymers emerged in the scientific literature as discrete entities of large molar mass comparable to that of classical polymers but built through non-covalent bonds among monomers. Supramolecular polymers exist in biological systems, and potentially blend the physical properties of covalent polymers with unique features such as high degrees of internal order within the polymeric structure, defined shapes, and novel dynamics. This trend article provides a summary of seminal contributions in supramolecular polymerization and provides recent examples from the Stupp laboratory to demonstrate the potential applications of an exciting class of materials composed fully or partially of supramolecular polymers. Finally, in closing, we provide our perspective on future opportunities provided by this field at the onset of a second century of polymers. It is our objective here to demonstrate that this second century could be as prosperous, if not more so, than the preceding one.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Screening of Coulombic Interactions To Achieve a Higher Power Factor in Conjugated Polymers

Thermoelectric properties of conducting polymers typically suffer from molecular chain disordering, as charge transport is predominantly controlled by morphology. This is especially more problematic when counterions are introduced to tune the carrier concentration for optimal thermoelectric performance, which disturbs the morphology further. Here, in this work, we introduce a new avenue for enhancing thermoelectric properties without needing to regulate the morphology, namely, by controlling the coulombic interaction between polarons and counterions. We perform in situ de-doping thermoelectric experiments over 3 orders of magnitude change in electrical conductivity of three distinct thermoelectric polymers, namely, poly(3-hexylthiophene-2,5-diyl) (P3HT), poly[2,5-bis(3-dodecylthiophen-2-yl)thieno[3,2-b]thiophene] (PBTTT-C 12 ), and poly[2,5-(2-octyldodecyl)-3,6-diketopyrrolopyrrole-alt-5,5-(2,5-di(thien-2-yl)thieno[3,2-b]thiophene)] (OD-PDPP2T-TT) conjugated polymers, followed by grazing-incidence wide-angle X-ray scattering (GIWAXS) to study their respective morphologies. We demonstrate a 9-fold enhancement in the thermoelectric power factor in OD-PDPP2T-TT compared to PBTTT-C 12 and link it to the coulombic screening of charge carriers, including in the optimally doped regime. We support this hypothesis using Boltzmann transport equations and show that, in both P3HT and PBTTT-C 12 , as the polymer is doped, impurity scattering remains the dominant scattering mechanism, while in OD-PDPP2T-TT, the scattering mechanism changes from impurity to acoustic phonon limited, resulting in more effective screening of ionized counterions. Our results provide an additional knob to enhance the fundamental understanding of thermoelectric physics of conducting polymers and provide a pathway to achieve higher performance in the field of organic thermoelectrics.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Deuteration Effects on the Physical and Optoelectronic Properties of Donor–Acceptor Conjugated Polymers

The significant differences in scattering cross sections between deuterium and protium are unique to neutron scattering techniques and have been a long-standing area of interest within the neutron scattering community. Researchers have explored selective deuteration to manipulate scattering contrast in soft matter systems, leading to the widespread use of deuterium labeling in materials development. As deuteration changes the atomic mass, it alters physical properties such as molecular volume, polarizability, and polarity, which in turn may affect noncovalent interactions and crystal ordering. Despite previous studies, there remains a limited understanding of how deuteration impacts donor–acceptor (DA) conjugated polymers. To address this, we synthesized deuterated DPP polymers and systematically investigated the effects of side-chain deuteration on their thermal stability, crystal packing, morphology, and optoelectronic properties. We found that deuteration increased the melting and crystallization temperatures of DPP polymers, although it did not significantly alter their morphology, molecular packing, or charge mobility. These properties were assessed by using atomic force microscopy (AFM), X-ray scattering, and thin-film transistor device measurements, respectively, for DPP polymers. Our work shows that deuterium labeling could be a powerful method for controlling scattering length density, enabling neutrons to study the structure and dynamics of conjugated polymers without impacting their electronic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Physical and Chemical Responses of Amidine-Containing Polymers in the Capture and Release of CO 2

Polymeric materials containing amidine motifs are of high interest due to their ability to reversibly capture and release CO 2 at ambient temperature. Here, in this study, we probe physical and chemical responses of styrene-based copolymers containing linear amidine motifs as functions of CO 2 and inert gas exposures and temperature. A copper-catalyzed azide–alkyne cycloaddition “click” reaction involving N′-propargyl-N,N-dimethylacetamidine is used to modify random copolymers, resulting in an array of linear amidine motifs along the chain backbone with the amount of CO 2 -active amidine controlled by the copolymer composition. Through thermogravimetric measurements, we demonstrate that the amidine-functionalized copolymers efficiently capture CO 2 upon exposure to a stream of CO 2 (at 27 °C) and release it at a slightly elevated temperature (50 °C) when exposed to an inert gas stream (N 2 ). In addition to displaying a maximum adsorption capacity of 22 wt % in the presence of pure CO 2 , the copolymers show composition-dependent direct air capture (DAC) behaviors. Small molecule analogs are used to definitively understand degradation via chemical hydrolysis of the amidine moiety, which leads to insolubility and a large reduction in CO 2 adsorption capacity (1.7 wt %). Neutron vibrational spectroscopy and DFT calculations confirm that CO 2 binds strongly to the amidine motif, inducing a strong bending of the CO 2 molecule from its linear geometry. The coupled insights into mechanisms and behaviors of CO 2 adsorption in amidine-functionalized polymers provides a foundation for future investigations of CO 2 -responsive polymers and soft materials to improve carbon capture and sequestration technologies.

Chun, Danielle J.↗
DOE OSTI2025

Stereogenic-at-silicon hybrid conjugated polymers

Stereoregularity in carbon-based polymers impacts critical physical properties such as crystallinity, but achieving comparable precision in polysilanes remains challenging. Herein, we report the synthesis of hybrid σ,π-conjugated polysilanes with defined stereoregularity, derived from cis- and trans-cyclosilane building blocks. Using Kumada polycondensation, we accessed a series of atactic, trans-enriched, and cis-enriched polysilanes, enabling a systematic investigation of how tacticity influences thermal and optical properties. Differential scanning calorimetry revealed distinct glass transition behaviors for stereoregular polymers compared to their atactic counterpart, and UV-vis spectroscopy demonstrated enhanced spectral resolution upon annealing of stereoregular films. A linear silane-based analog further underscored the structural impact of cyclic stereogenic units. These findings highlight how stereochemical precision in silicon-containing backbones can modulate macromolecular properties, opening avenues for the rational design of stereoregular polysilanes.

36 MATERIALS SCIENCE↗
NASA NTRS2017

Ionic Polyimides: New High Performance Polymers for Additive Manufacturing

There is currently a very limited set of engineering polymers that have been demonstrated as viable for use in 3-D printing. Additive manufacturing of custom components will require a much larger array of polymers, especially those with physical, thermal, chemical, and mechanical properties that can be tailor-made. The development of ‘Ionic Polyimides’ offers a solution to this shortage by combining the well understood and widely accepted properties of conventional polyimides, with a new approach to polymer synthesis. Polyimides and polymeric ionic liquids (poly(ILs)) are at the forefront of advanced polymer materials, each with their own set of advantages and disadvantages. While it is clear that more types of polymer materials are needed for fused deposition modeling (FDM) additive manufacturing, there is a need to explore these classes of materials. The synthesis process developed by the Bara Research Group at the University of Alabama allows full control over polymer structure, nanostructure, thermal, electrical, and physical properties making them a prime candidate for use in the additive manufacturing process. Furthermore, the new process allows us to tailor-make a high strength polymer that can be used to fabricate filament feedstock instead of pellets for 3D printing. The primary objective of this proposal is to determine the relationship between molecular structure, physical properties, and performance of ionic polyimides. Further, we seek to determine their utility as materials suitable for additive manufacturing of components used in aerospace vehicles, with an emphasis on characterizing and simulating their thermal behaviors and properties. This proposal addresses the need for fundamental research on a customizable polymer filament feedstock for 3-D printing with tailor-made properties potentially making it superior to the commercial blends offered in industry today. The deliverables for this project are the creation of a database that will detail the relationships between the molecular structure and physical properties for the ionic polyimide of interest (e.g. Tg/Tm (Glass Transition Temperature divided by Melting Point)) relative to different ionic polyimide structures). This new database will provide a “road map” to the development of the first generation of materials and ultimately proof-of-concept.

Jackson, Enrique↗
DOE OSTI2021

Strong tough hydrogels via the synergy of freeze-casting and salting out

Natural load-bearing materials like tendons possess high water content of ~70% but14 are still strong and tough even when used for over 1 million cycles per year, which is owed to the hierarchical assembly of anisotropic structures across multi-length-scales . In imitation of natural systems, various hydrogels have been created via methods like electro-spinning, extrusion, compositing, freeze casting, self-assembly, and mechanical stretching for improved mechanical performance. However, in contrast to tendons, many hydrogels with the same high water content do not show high strength, large toughness or high fatigue resistance. In this work, we present a strategy to produce strong, tough and fatigue resistant hydrogels with multi-length-scale hierarchical architecture using a freezing-assisted salting-out treatment. The produced exemplary poly(vinyl alcohol) hydrogels are highly anisotropic, comprising micrometer-scale honeycomb-like pore walls, which in turn comprise interconnected nanofibrils meshes, entirely physically assembled from polymer chains. These hydrogels are made of 70-95% water but can exhibit ultra-high ultimate stress (23.5 ± 2.7 MPa) and strain (2900 ± 450%), giant 32226 toughness (210 ± 13 MJ/m , 175 ± 8 kJ/m) and remarkable fatigue threshold (10.5 ± 1.3 kJ/m), which are 10 times tougher than natural tendon. The presented strategy could expand the applicability of weak polymeric material, like hydrogels, in practical applications that requires long-term services with high-loads and abrupt-impacts and extend the development of structural hydrogels.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Investigation of phase-change coatings for variable thermal control of spacecraft

An investigation was conducted to determine the feasibility of producing a spacecraft coating system that could vary the ratio of its solar absorptance to thermal emittance to adjust automatically for changes in the thermal balance of a spacecraft. This study resulted in a new concept called the phase-change effect which uses the change that occurs in the optical properties of many materials during the phase transition from a crystalline solid to an amorphous material. A series of two-component model coatings was developed which, when placed on a highly reflecting substrate, exhibited a sharp decrease in solar absorptance within a narrow temperature range. A variable thermal control coating can have a significant amount of temperature regulation with the phase-change effect. Data are presented on several crystallite-polymer formulations, their physical and optical properties, and associated phase-change temperatures. Aspects pertaining to their use in a space environment and an example of the degree of thermal regulation attainable with these coatings is also given.

Kelliher, W. C.↗
NASA NTRS1988

Long-life assurance for Space Station - Is it an issue?

Various issues related to the long-life assurance (LLA) of the Space Station (SS) are discussed. The effects of exposure to atomic oxygen, radiation, thermal cycling, micrometeoroid and debris damage, and the physical aging of polymers on the SS materials are examined. The proper design of the SS truss system and pressure vessels, electronic systems, mechanical systems, and software for LLA is addressed.

Cruse, T. A.↗
NASA NTRS1999

Experimental and Analytical Studies for a Computational Materials Program

The studies supported by Grant NAG1-1780 were directed at providing physical data on polymer behavior that would form the basis for computationally modeling these types of materials. Because of ongoing work in polymer characterization this grant supported part of a larger picture in this regard. Efforts went into two combined areas of their time dependent mechanical response characteristics: Creep properties on the one hand, subject to different volumetric changes (nonlinearly viscoelastic behavior) and time or frequency dependence of dilatational material behavior. The details of these endeavors are outlined sufficiently in the two appended publications, so that no further description of the effort is necessary.

Knauss, W. G.↗
NASA NTRS2000

The Life Cycle Application of Intelligent Software Modeling for the First Materials Science Research Rack

Marshall Space Flight Center (MSFC) has been funding development of intelligent software models to benefit payload ground operations for nearly a decade. Experience gained from simulator development and real-time monitoring and control is being applied to engineering design, testing, and operation of the First Material Science Research Rack (MSRR-1). MSRR-1 is the first rack in a suite of three racks comprising the Materials Science Research Facility (MSRF) which will operate on the International Space Station (ISS). The MSRF will accommodate advanced microgravity investigations in areas such as the fields of solidification of metals and alloys, thermo-physical properties of polymers, crystal growth studies of semiconductor materials, and research in ceramics and glasses. The MSRR-1 is a joint venture between NASA and the European Space Agency (ESA) to study the behavior of different materials during high temperature processing in a low gravity environment. The planned MSRR-1 mission duration is five (5) years on-orbit and the total design life is ten (IO) years. The MSRR-1 launch is scheduled on the third Utilization Flight (UF-3) to ISS, currently in February of 2003). The objective of MSRR-1 is to provide an early capability on the ISS to conduct material science, materials technology, and space product research investigations in microgravity. It will provide a modular, multi-user facility for microgravity research in materials crystal growth and solidification. An intelligent software model of MSRR-1 is under development and will serve multiple purposes to support the engineering analysis, testing, training, and operational phases of the MSRR-1 life cycle development. The G2 real-time expert system software environment developed by Gensym Corporation was selected as the intelligent system shell for this development work based on past experience gained and the effectiveness of the programming environment. Our approach of multi- uses of the simulation model and its intuitive graphics capabilities is providing a concurrent engineering environment for rapid prototyping and development. Operational schematics of the MSRR-1 electrical, thermal control, vacuum access, and gas supply systems, and furnace inserts are represented graphically in the environment. Logic to represent first order engineering calculations is coded into the knowledge base to simulate the operational behavior of the MSRR-1 systems. An example of engineering data provided includes electrical currents, voltages, operational power, temperatures, thermal fluid flow rates. pressures, and component status indications. These type of data are calculated and displayed at appropriate instrumentation points, and the schematics are animated to reflect the simulated operational status of the MSRR-1. The software control functions are also simulated to represent appropriate operational behavior based on automated control and response to commands received by the crew or ground controllers. The first benefit of this simulation environment is being realized in the high fidelity engineering analysis results from the electrical power system G2 model. Secondly, the MSRR-1 simulation model will be embedded with a hardware mock-up of the MSRR-1 to provide crew training on MSRR-1 integrated payload operations. G2 gateway code will output the simulated instrumentation values, termed as telemetry, in a flight-like data stream so that the crew has realistic and accurate simulated MSRR-1 data on the flight displays which will be designed for crew use. The simulation will also respond appropriately to crew or ground initiated commands, which will be part of normal facility operations. A third use of the G2 model is being planned; the MSRR-1 simulation will be integrated with additional software code as part of the test configuration of the primary onboard computer, or Master Controller, for MSRR-1. We will take advantage of the G2 capability to simulate the flight like data stream to test flight software responses and behavior. A fourth use of the G2 model will be to train the Ground Support Personnel that will monitor the MSRR-1 systems and payloads while they are operating aboard the ISS. The intuitive, schematic based environment will provide an excellent foundation for personnel to understand the integrated configuration and operation of the MSRR-1, and the anticipated telemetry feedback based on operational modes of the equipment. Expert monitoring features will be enhanced to provide a smart monitoring environment for the operators. These features include: (1) Animated, intuitive schematic-based displays which reflect telemetry values, (1) Real-time plotting of simulated or incoming sensor values, (3) High/Low exception monitoring for analog data, (4) Expected state monitoring for discrete data, (5) Data trending, (6) Automated malfunction procedure execution to diagnose problems, (7) Look ahead capability to planned MSRR-1 activities in the onboard timeline. And finally, the logic to calculate telemetry values will be deactivated, and the same environment will interface to the incoming data for the real-time telemetry stream to schematically represent the onboard hardware configuration. G2 will be the foundation for the real-time monitoring and control environment. In summary, our MSRR-1 simulation model spans many elements of the life cycle development of this project: Engineering Analysis, Test and Checkout, Training of Crew and Ground Personnel, and Real-time monitoring and control. By utilizing the unique features afforded by an expert system development environment, we have been able to synergize a powerful tool capable of addressing our project needs at every phase of project development.

Rice, Amanda↗
NASA NTRS2004

Temporal Treatment of a Thermal Response for Defect Depth Estimation

Transient thermography, which employs pulse surface heating of an inspected component followed by acquisition of the thermal decay stage, is gaining wider acceptance as a result of its remoteness and rapidness. Flaws in the component s material may induce a thermal contrast in surface thermograms. An important issue in transient thermography is estimating the depth of a subsurface flaw from the thermal response. This improves the quantitative ability of the thermal evaluation: from one scan it is possible to locate regions of anomalies in thickness (caused by corrosion) and estimate the implications of the flaw on the integrity of the structure. Our research focuses on thick composite aircraft components. A long square heating pulse and several minutes observation period are required to receive an adequate thermal response from such a component. Application of various time-related informative parameters of the thermal response for depth estimation is discussed. A three-dimensional finite difference model of heat propagation in solids in Cartesian coordinates is used to simulate the thermographic process. Typical physical properties of polymer graphite composites are assumed for the model.

Plotnikov, Y. A.↗
NASA NTRS1998

Modeling of the Multiparameter Inverse Task of Transient Thermography

Transient thermography employs preheated surface temperature variations caused by delaminations, cracks, voids, corroded regions, etc. Often, it is enough to detect these changes to declare a defect in a workpiece. It is also desirable to obtain additional information about the defect from the thermal response. The planar size, depth, and thermal resistance of the detected defects are the parameters of interest. In this paper a digital image processing technique is applied to simulated thermal responses in order to obtain the geometry of the inclusion-type defects in a flat panel. A three-dimensional finite difference model in Cartesian coordinates is used for the numerical simulations. Typical physical properties of polymer graphite composites are assumed. Using different informative parameters of the thermal response for depth estimation is discussed.

Plotnikov, Y. A.↗
NASA NTRS2009

Complex Multifunctional Polymer/Carbon-Nanotube Composites

A methodology for developing complex multifunctional materials that consist of or contain polymer/carbon-nanotube composites has been conceived. As used here, "multifunctional" signifies having additional and/or enhanced physical properties that polymers or polymer-matrix composites would not ordinarily be expected to have. Such properties include useful amounts of electrical conductivity, increased thermal conductivity, and/or increased strength. In the present methodology, these properties are imparted to a given composite through the choice and processing of its polymeric and CNT constituents.

Patel, Pritesh↗
DOE OSTI2022

A Micro-Mechanical Constitutive Model to Predict Hygrothermal Aging of Cross-Linked Polymers

Abstract A multi-physics material model is presented to describe the effects of temperature, oxygen, and humidity on the constitutive response of cross-linked polymers. The effect of hygrothermal damage on the mechanical integrity of the polymer matrix can be considered as the result of damage accumulation of two independent aging mechanism namely, i) thermo-oxidative, and ii) hydrolytic aging. In order to capture the mutual effects of thermo-oxidative and hydrolytic aging, an assumption has been made that each of the aging phenomenon can be superposed to each other. In fact, each of them works independently and as a result, they can compete with each other. Utilizing the theory of network decomposition, all phenomena and their correlation were modeled and thus, the strain energy function of the polymer matrix is written with respect to four independent mechanisms, i) the shrinking original matrix that has neither been attacked by water nor oxygen, ii) conversion of the first network to two new network due to the reduction and formation of cross-links, and iii) energy loss from network degradation due to attack of the water molecules to polymer active agents. Moreover, the proposed model is micro-mechanically based and is mainly relevant on thin samples due to our underlying assumption of homogeneous diffusion of oxygen and water throughout the matrix. The model has been validated against extensive data-sets obtained from experiments we specifically designed for concept validation.

Bahrololoumi, Amir↗
DOE OSTI2020

Multiamorphous Phases in Diketopyrrolopyrrole-Based Conjugated Polymers: From Bulk to Ultrathin Films

The glass transition temperature (T g ) of conjugated polymers is a crucial physical parameter that governs their mechanical and electrical properties for applications from sensor technology to skin-like electronics. Despite some well-developed methods that exist for detecting T g of conjugated polymers, there is still a need for the combination of advanced calorimetric methodologies to characterize T g in a broad range of temperatures and scales from bulk to nanometer-thin films. In this work, alternating current (ac) chip calorimetry and flash differential scanning calorimetry (flash DSC) are applied to successfully identify the Tgs and segmental relaxations of conjugated polymers. The detected relaxations were interpreted, in agreement with existing observations in similar systems, as a side-chain relaxation (low temperature), mobile amorphous fractions (MAF), and rigid amorphous fractions (RAF). T g s of MAF and RAF increase and decrease with increasing size of fused thiophene units in the backbone, respectively. The T g s of diketopyrrolopyrrole-based conjugated polymer thin films are also identified by the same method, with both T g s showing a decreased value compared to those of bulk samples. Furthermore, the weight fractions of MAF and RAF with various film thicknesses are qualitatively analyzed based on the heat capacity step of each amorphous fraction during the glass transition. This facile method gives insights into the physical nature of amorphous phases in conjugated polymers for better revealing their structure-property relationships, which will guide the designs of new materials with optimized electrical and mechanical properties in the future.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗