SEARCH · Search NASA

Results for “power distribution unit”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1996

Cardiac Monitor

Under contract to Johnson Space Center, the University of Minnesota developed the concept of impedance cardiography as an alternative to thermodilution to access astronaut heart function in flight. NASA then contracted Space Labs, Inc. to construct miniature space units based on this technology. Several companies then launched their own impedance cardiography, including Renaissance Technologies, which manufactures the IQ System. The IQ System is 5 to 17 times cheaper than thermodilution, and features the signal processing technology called TFD (Time Frequency Distribution). TFD provides three- dimensional distribution of the blood circulation force signals, allowing visualization of changes in power, frequency and time.

Source record↗

NASA NTRS2019

NASA Proof-of-Concept 1-W Stirling Convertor Development for Small RPS

Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future small spacecraft with electrical power by converting heat from one or more Light Weight Radioisotope Heater Units (LWRHU). An initial design converts multiple watts of heat to one watt of electrical power output using a Stirling convertor. A variety of mission concepts have been studied by NASA and the U. S. Department of Energy (DOE) that would utilize low power Radioisotope Power Systems (RPS) for probes, landers, rovers, and repeaters. These missions would contain science instruments distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Landers could be used to provide data such as, radiation, temperature, pressure, seismic activity, and other surface measurements for planetary science and to inform future mission planners. The studies propose using fractional versions of the General Purpose Heat Source (GPHS) or multiple LWRHUs to heat power conversion technologies for science instruments and communication. Dynamic power systems are capable of higher conversion efficiencies, which could enable equal power using less fuel or more power using equal fuel, when compared to less efficient static power conversion technologies. Providing spacecraft with more power would decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. Efforts to develop the concept have focused on maturation of a 1-We convertor and controller design and performance evaluation of an evacuated metal foil insulation. A proof-of-concept 1-We convertor, controller, and evacuated metal foil insulation package have been fabricated and are undergoing characterization testing. The current status, findings, and path forward for the effort are explained in this paper.

Schifer, Nicholas A.↗

NASA NTRS1990

Delivery and application of precise timing for a traveling wave powerline fault locator system

The Bonneville Power Administration (BPA) has successfully operated an in-house developed powerline fault locator system since 1986. The BPA fault locator system consists of remotes installed at cardinal power transmission line system nodes and a central master which polls the remotes for traveling wave time-of-arrival data. A power line fault produces a fast rise-time traveling wave which emanates from the fault point and propagates throughout the power grid. The remotes time-tag the traveling wave leading edge as it passes through the power system cardinal substation nodes. A synchronizing pulse transmitted via the BPA analog microwave system on a wideband channel sychronizes the time-tagging counters in the remote units to a different accuracy of better than one microsecond. The remote units correct the raw time tags for synchronizing pulse propagation delay and return these corrected values to the fault locator master. The master then calculates the power system disturbance source using the collected time tags. The system design objective is a fault location accuracy of 300 meters. BPA's fault locator system operation, error producing phenomena, and method of distributing precise timing are described.

Street, Michael A.↗

NASA NTRS2019

Small Stirling Technology Exploration Power for Future Space Science Missions

High efficiency dynamic Radioisotope Power Systems (RPS) could be mission enabling for low power space applications such as small probes, landers rovers, and communication repeaters. These applications would contain science instruments and be distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Small RPS could be used to provide power for sensing radiation, temperature, pressure, seismic activity, and other measurements of interest to planetary scientists. Small RPS would use fractional versions of the General Purpose Heat Source (GPHS) or Light Weight Radioisotope Heater Units (LWRHU), to heat power conversion technologies. Dynamic power systems are capable of three to four times higher conversion efficiency compared to static power conversion technologies, and would provide an equal amount of power using less fuel or more power using an equal amount of fuel. Providing spacecraft with more power could decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. NASA GRC is developing a low power dynamic RPS that would convert heat from multiple LWRHU to one watt of usable direct current electric power for spacecraft instrumentation and communication. The power system could be used to charge batteries or capacitors for higher power burst usage. The initial design, called Small Stirling Technology Exploration Power (smallSTEP), is around 3 kg, 11 cm diameter X 32 cm long, and converts 8 watts of heat to one watt of electricity using a Stirling convertor. This low power conversion system represents a new class of RPS with power levels two orders of magnitude lower than prototypes currently being developed for space applications under NASA contracts. Development of the 1-watt RPS includes maturation of convertor and controller designs, performance evaluation of an evacuated metal foil insulation, and development of system interfaces. Initial demonstration of the subsystems has been completed in a laboratory environment and a higher fidelity system is being pursued for demonstration in relevant environments for use on small spacecraft needed to carry out future space science missions.

Wilson, Scott D.↗

NASA NTRS2019

Small Stirling Technology Exploration Power for Future Space Science Missions

High efficiency dynamic Radioisotope Power Systems (RPS) could be mission enabling for low power space applications such as small probes, landers rovers, and communication repeaters. These applications would contain science instruments and be distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Small RPS could be used to provide power for sensing radiation, temperature, pressure, seismic activity, and other measurements of interest to planetary scientists. Small RPS would use fractional versions of the General Purpose Heat Source (GPHS) or Light Weight Radioisotope Heater Units (LWRHU), to heat power conversion technologies. Dynamic power systems are capable of three to four times higher conversion efficiency compared to static power conversion technologies, and would provide an equal amount of power using less fuel or more power using an equal amount of fuel. Providing spacecraft with more power could decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. NASA Glenn Research Center (GRC) is developing a low power dynamic RPS that would convert heat from multiple LWRHU to one watt of usable direct current electric power for spacecraft instrumentation and communication. The power system could be used to charge batteries or capacitors for higher power burst usage. The initial design, called Small Stirling Technology Exploration Power (smallSTEP), is around 3 kg, 11 cm diameter X 32 cm long, and converts 8 watts of heat to one watt of electricity using a Stirling convertor. This low power conversion system represents a new class of RPS with power levels two orders of magnitude lower than prototypes currently being developed for space applications under NASA contracts. Development of the 1-watt RPS includes maturation of convertor and controller designs, performance evaluation of an evacuated metal foil insulation, and development of system interfaces. Initial demonstration of the subsystems has been completed in a laboratory environment and a higher fidelity system is being pursued for demonstration in relevant environments for use on small spacecraft needed to carry out future space science missions.

Wilson, Scott↗

NASA NTRS1978

The electron spectrometer experiment on ISEE-1

A six-axis electron spectrometer for the ISEE-1 spacecraft is described and some typical early results presented. This instrument, designed for three-dimensional plasma distribution function studies in the solar wind, magnetosheath, outer magnetosphere, and near tail regions, has three energy ranges: 7.5-512 eV, 11-2062 eV, and 109-7285 cV, respectively. Two channel electron multipliers are used at the output of each of six cylindrical electrostatic analyzers. The total mass of two sensors and a data processing unit is 4.9 kg and the power comsumption is 3.5 W. Two hundred information bits/s telemetry rate is required.

Ogilvie, K. W.↗

NASA NTRS1980

The dish-Rankine SCSTPE program (Engineering Experiment no. 1)

Activities planned for phase 2 Of the Small Community Solar Thermal Power Experiment (PFDR) program are summarized with emphasis on a dish-Rankine point focusing distributed receiver solar thermal electric system. Major design efforts include: (1) development of an advanced concept indirect-heated receiver;(2) development of hardware and software for a totally unmanned power plant control system; (3) implementation of a hybrid digital simulator which will validate plant operation prior to field testing; and (4) the acquisition of an efficient organic Rankine cycle power conversion unit. Preliminary performance analyses indicate that a mass-produced dish-Rankine PFDR system is potentially capable of producing electricity at a levelized busbar energy cost of 60 to 70 mills per KWh and with a capital cost of about $1300 per KW.

Pons, R. L.↗

NASA NTRS1935

Large-Scale Boundary-Layer Control Tests on Two Wings in the NACA 20-Foot Wind Tunnel, Special Report

Tests were made in the N.A.C.A. 20-foot wind tunnel on: (1) a wing, of 6.5-foot span, 5.5-foot chord, and 30 percent maximum thickness, fitted with large end plates and (2) a 16-foot span 2.67-foot chord wing of 15 percent maximum thickness to determine the increase in lift obtainable by removing the boundary layer and the power required for the blower. The results of the tests on the stub wing appeared more favorable than previous small-scale tests and indicated that: (1) the suction method was considerably superior to the pressure method, (2) single slots were more effective than multiple slots (where the same pressure was applied to all slots), the slot efficiency increased rapidly for increasing slot widths up to 2 percent of the wing chord and remained practically constant for all larger widths tested, (3) suction pressure and power requirements were quite low (a computation for a light airplane showed that a lift coefficient of 3.0 could be obtained with a suction as low as 2.3 times the dynamic pressure and a power expenditure less than 3 percent of the rated engine power), and (4) the volume of air required to be drawn off was quite high (approximately 0.5 cubic feet per second per unit wing area for an airplane landing at 40 miles per hour with a lift coefficient of 3,0), indicating that considerable duct area must be provided in order to prevent flow losses inside the wing and insure uniform distribution of suction along the span. The results from the tests of the large-span wing were less favorable than those on the stub wing. The reasons for this were, probably: (1) the uneven distribution of suction along the span, (2) the flow losses inside the wing, (3) the small radius of curvature of the leading edge of the wing section, and (4) the low Reynolds Number of these tests, which was about one half that of the stub wing. The results showed a large increase in the maximum lift coefficient with an increase in Reynolds Number in the range of the tests. The results of drag tests showed that the profile drag of the wing was reduced and the L/D ratio was increased throughout the range of lift coefficients corresponding to take-off and climb but that the minimum drag was increased. The slot arrangement that is best for low drag is not the same, however, as that for maximum lift.

Freeman, Hugh B.↗

NASA NTRS1989

Space Station Freedom power - A reliability, availability, and maintainability assessment of the proposed Space Station Freedom electric power system

A preliminary reliability, availability, and maintainability (RAM) analysis of the proposed Space Station Freedom electric power system (EPS) was performed using the unit reliability, availability, and maintainability (UNIRAM) analysis methodology. Orbital replacement units (ORUs) having the most significant impact on EPS availability measures were identified. Also, the sensitivity of the EPS to variations in ORU RAM data was evaluated for each ORU. Estimates were made of average EPS power output levels and availability of power to the core area of the space station. The results of assessments of the availability of EPS power and power to load distribution points in the space stations are given. Some highlights of continuing studies being performed to understand EPS availability considerations are presented.

Turnquist, S. R.↗

NASA NTRS2019

Decomposition of Electron Ionization Mass Spectra for Space Application Using a Monte-Carlo approach

Rationale: Quadrupole mass spectrometers equipped with an electron ionization (EI) sources have been widely used in space exploration to investigate the composition of planetary surfaces and atmospheres. However, the complexity of the samples and the minimal calibration for the fragmentation of molecules in the ionization chambers have prevented the deconvolution of the majority of the mass spectra obtained at different targets, thus limiting the determination of the exact composition of the samples analyzed. We propose a Monte‐Carlo approach to solve this issue mathematically. Methods: We decomposed simulated mass spectra of mixtures acquired with unit resolving power mass spectrometers and EI sources into the sum of the single components fragmentation patterns weighted by their relative concentration using interior‐point least‐square fitting. To fit compounds with poorly known fragmentation patterns, we used a Monte‐Carlo method to vary the intensity of individual fragment ions. We then decomposed the spectrum thousands of times to obtain a statistical distribution. Results: By performing the deconvolution on a mixture of seven different molecules with interfering fragmentation patterns (H2O, O2, CH4, Ar, N2, C2H4, and C2H6) we show that this approach retrieves the mixing ratio of the individual components more accurately than regular mass spectra decomposition methods that rely on fragmentation patterns from general databases. It also provides the probability density function for each species's mixing ratio. Conclusions: By removing the solution degeneracy in the decomposition of mass spectra, the method described herein could significantly increase the scientific retrieval from archived space flight mass spectrometry data, where calibration of the ionization source is no longer an option.

Thomas Gautier↗

NASA NTRS1984

An estimate of star formation efficiency in molecular clouds

From the existing data in the literature it is shown that there is a linear correlation between cloud mass derived from CO observations and the associated luminosity obtained from far-IR observations over a large luminosity range of 10 to the 4th to 10 to the 8th solar luminosities. The mean value of luminosity per unit mass for a giant molecular cloud is 5.6 solar-L/solar-M. The star-forming efficiency of the molecular cloud over its lifetime of 5-10 x 10 to the 7th yr is found to be 0.2-0.3, which yields the present star-forming rate of 6-11 solar masses per year. Furthermore, the integral luminosity distribution is a power-law with an exponent of about -0.5. The correlation between cloud mass and the far-IR luminosity observed for a sample of nuclei of external galaxies corresponds to molecular clouds similar to those in the Galaxy.

Rengarajan, T. N.↗

NASA NTRSDate not supplied

Development of a Portable Stand-Alone 20 K Brayton Cycle Helium Refrigeration System

From 2012 to 2015, NASA funded development of the Ground Operations Demonstration Unit for Liquid Hydrogen (GODU-LH2) at Kennedy Space Center that scaled up and matured Integrated Refrigeration and Storage (IRAS) technology. IRAS involves the integration of an external helium refrigeration system with a cryogenic storage tank via an internal heat exchanger and allows advanced operations such as zero boiloff and densification of the liquid. The refrigeration system employed for GODU-LH2 was a Linde LR1620 piston-Brayton cycle machine with an RSX helium compressor. The GODU-LH2 system was installed in two separate shipping containers—one housing the cold-box, compressor, and gas management hardware, and the other the water chiller unit—with 480 VAC and 120 VAC electrical power fed from external hardware at the test site, and data capture and controls achieved using four different, independent software packages. From 2017 to 2019, in support of a densified hydrogen loading test program, the entire system was repackaged into a single, 40’ (12 m) shipping container, including the refrigeration system, water chiller, and electrical power distribution hardware, and controls were consolidated into a single Allen Bradley PanelView. Details regarding the design, build-out, and testing of the system will be presented and discussed.

W F Reaves↗

NASA NTRS1991

Comparison of dynamic isotope power systems for distributed planet surface applications

Dynamic isotope power system (DIPS) alternatives were investigated and characterized for the surface mission elements associated with a lunar base and subsequent manned Mars expedition. System designs based on two convertor types were studied. These systems were characterized parametrically and compared over the steady-state electrical output power range 0.2 to 20 kWe. Three methods of thermally integrating the heat source and the Stirling heater head were considered, depending on unit size. Figures of merit were derived from the characterizations and compared over the parametric range. Design impacts of mission environmental factors are discussed and quantitatively assessed.

Bents, David J.↗

NASA NTRS1992

Large-scale structure in the Southern Sky Redshift Survey

The power spectrum from the Southern Sky Redshift Survey and the CfA samples are measured in order to explore the amplitude of fluctuation in the galaxy density. At lambda of less than or equal to 30/h Mpc the observed power spectrum is quite consistent with the standard CDM model. At larger scales the data indicate an excess of power over the standard CDM model. The observed power spectrum from these optical galaxy samples is in good agreement with that drawn from the sparsely sampled IRAS galaxies. The shape of the power spectrum is also studied by examining the relation between the genus per unit volume and the smoothing length. It is found that, over Gaussian smoothing scales from 6 to 14/h Mpc, the power spectrum has a slope of about -1. The topology of the galaxy density field is studied by measuring the shift of the genus curve from the Gaussian case. Over all smoothing scales studied, the observed genus curves are consistent with a random phase distribution of the galaxy density field, as predicted by the inflationary scenarios.

Park, Changbom↗

NASA NTRSDate not supplied

Analysis of the Electrical Grid for UAM

A wide range of challenges must be overcome to conduct Urban Air Mobility (UAM) operations at scale with electric vertical takeoff and landing aircraft as envisioned. This presentation is on an analysis of one potential infrastructure challenge for UAM: available electrical grid power capacity. The success of UAM depends on the availability of electricity, which will be increasingly impacted by the proliferation of ground electric vehicles over time. Under the best-case assumption that electricity can be transmitted and distributed as needed within each interconnection (i.e., electrical grid), it is estimated that the maximum number of UAM aircraft that can charge simultaneously in the continental United States will decrease by 20% from about 595 thousand in the year 2021 to about 475 thousand in the year 2050 due to the projected increase in ground electric vehicles.

electrical grid; urban air mobility; electric vehi↗

NASA NTRSDate not supplied

Analysis of Electrical Grid Capacity by Interconnection for Urban Air Mobility

A wide range of challenges must be overcome to conduct Urban Air Mobility (UAM)operations at scale with electric vertical take-off and landing aircraft as envisioned. This paper documents an analysis of one potential infrastructure challenge for UAM: available electrical grid power capacity. The success of UAM depends on the availability of electricity, which will be increasingly impacted by the proliferation of ground electric vehicles(EVs) over time. Under the best-case assumption that electricity can be transmitted and distributed as needed within each interconnection (i.e., electrical grid), it is estimated that the maximum number of UAM aircraft that can charge simultaneously in the continental United States will decrease by 20% from about 595 thousand in the year 2021 to about 475 thousand in the year 2050due to the projected increase in ground EVs.

electrical grid↗

NASA NTRSDate not supplied

Analysis of Electrical Grid Capacity by Interconnection for Urban Air Mobility

electrical grid↗

NASA NTRS2006

The USNA MIDN Microdosimeter Instrument

This paper describes the MIcroDosimetry iNstrument (MIDN) mission now under development at the United States Naval Academy. The instrument is manifested to fly on the MidSTAR-1 spacecraft, which is the second spacecraft to be developed and launched by the Academy s faculty and midshipmen. Launch is scheduled for 1 September 2006 on an ATLAS-5 launch vehicle. MIDN is a rugged, portable, low power, low mass, solid-state microdosimeter designed to measure in real time the energy distributions of energy deposited by radiation in microscopic volumes. The MIDN microdosimeter sensor is a reverse-biased silicon p-n junction array in a Silicon-On-Insulator (SOI) configuration. Microdosimetric frequency distributions as a function of lineal energies determine the radiation quality factors in support of radiation risk estimation to humans.

Pisacane, V. L.↗