Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

An experimental investigation of silicon wafer surface roughness and its effect on the pull-strength of plated metals

Plated silicon wafers with surface roughness ranging from 0.4 to 130 microinches, subjected to tensile pull-strength tests, were analyzed. Results show that the measured pull-strength of plated metals decrease with increasing silicon surface roughness, effecting a weakening of the cohesive strength of the wafer, possibly caused by microcracks or 'etch pits' in the silicon surface. The mean value of pull-strength for all wafers plated with the Ni-Cu-Cu sequence exceeded the required 450 g/0.02 sq cm, and at Ra = 0.4 microinches, the mean pull-strength for the Ni-Cu-Cu and Ni-Cu wafers were 2290 and 850 g/0.02 sq cm, respectively. The development of standardized methods for measuring contact pull-strength is suggested. These results may have some bearing on solar cell arrays problems.

Spiers, G. D.↗

An experimental investigation of silicon wafer surface roughness and its effect on the full strength of plated metals

Plated silicon wafers with surface roughness ranging from 0.4 to 130 microinches were subjected to tensile pull strength tests. Electroless Ni/electroless Cu/electroplated Cu and electroless Ni/electroplated Cu were the two types of plate contacts tested. It was found that smoother surfaces had higher pull strength than rougher, chemically etched surfaces. The presence of the electroless Cu layer was found to be important to adhesion. The mode of fracture of the contact as it left the silicon was studied, and it was found that in almost all cases separation was due to fracture of the bulk silicon phase. The correlation between surface roughness and mode of contact failure is presented and interpreted.

Spiers, G. D.↗

Analysis and testing for rotordynamic coefficients of turbulent annular seals with different, directionally-homogeneous surface-roughness treatment for rotor and stator elements

A combined analytical-computational method has been developed to calculate the transient pressure field and rotordynamic coefficients for high-pressure annular seals. The solution procedure applies to constant-clearance or the convergent tapered geometries of multistage centrifugal pumps which may have different surface roughness conditions on the stator and rotor seal elements. In experimental calculations with the method, the turbulent equations of Hirs (1973) are modified slightly to account for different surface roughness conditions, and a perturbation analysis is employed to develop zeroth and first order perturbation equations. Zeroth equations are also used to define both the leakage and circumferential flow due to shear stresses around the stator and rotor surfaces. The solution to analytical equations for four different surface roughnesses confirm the predicted net damping for the seals. A round-holed stator pattern yielded the highest net damping and lowest leakage of all the seals tested.

Childs, D. W.↗

Optimizing Aluminum Bonding: Exploring Surface Roughness and Contact Angle Effects through Plasma and Acid Etching Contrasts

The use of adhesives to replace traditional techniques like welding and riveting has been on the rise in various industries as increasingly complex geometries and situations for bonding is required. It’s well known in the scientific community that an adhesive bond is only as efficient as the surface preparation used beforehand. Plasma treatments have been shown to gently clean the surface by only removing the top-most layer from the adherend and “charging” the surface instead of berating it. Whereas chemical treatments “etch” the surface in hopes of increasing surface area by increasing surface roughness. This method can be difficult to control quantitatively and can generate waste leading to serious environmental concerns. This study aims to address the encountered differences between plasma treatments and acid etching on aluminum substrates for adhesive bonding. Treating the surface of adherends plays a crucial role in promoting a good bond between adhesive and adherend. In this study, the effects of plasma and acid treatments are categorized using surface roughness measurements as well as contact angle which have been shown to correlate to mechanical strength. When evaluating different surface treatments, it is notable to mention that not only surface roughness and contact angle play a role in determining which method is most effective but also the consequences of the treatment itself. It was found that although chemical etching was the most effective in increasing roughness and decreasing contact angle, it generates a large amount of waste and is not sustainable compared to plasma work which uses a renewable process. The results from this work provide a deeper understanding of the relationship between surface treatments and surface roughness/contact angle and how this relates to a stronger adhesive bond.

36 MATERIALS SCIENCE↗

Optimizing Aluminum Bonding: Exploring Surface Roughness and Contact Angle Effects through Plasma and Acid Etching Contrasts.

The use of adhesives to replace traditional techniques like welding and riveting has been on the rise in various industries as increasingly complex geometries and situations for bonding is required. It’s well known in the scientific community that an adhesive bond is only as efficient as the surface preparation used beforehand. Plasma treatments have been shown to gently clean the surface by only removing the top-most layer from the adherend and “charging” the surface instead of berating it. Whereas chemical treatments “etch” the surface in hopes of increasing surface area by increasing surface roughness. This method can be difficult to control quantitatively and can generate waste leading to serious environmental concerns. This study aims to address the encountered differences between plasma treatments and acid etching on aluminum substrates for adhesive bonding. Treating the surface of adherends plays a crucial role in promoting a good bond between adhesive and adherend. In this study, the effects of plasma and acid treatments are categorized using surface roughness measurements as well as contact angle which have been shown to correlate to mechanical strength. When evaluating different surface treatments, it is notable to mention that not only surface roughness and contact angle play a role in determining which method is most effective but also the consequences of the treatment itself. It was found that although chemical etching was the most effective in increasing roughness and decreasing contact angle, it generates a large amount of waste and is not sustainable compared to plasma work which uses a renewable process. The results from this work provide a deeper understanding of the relationship between surface treatments and surface roughness/contact angle and how this relates to a stronger adhesive bond

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Radiative Transfer Simulations of the Two-Dimensional Ocean Glint Reflectance and Determination of the Sea Surface Roughness

An optimized discrete-ordinate radiative transfer model (DISORT3) with a pseudo-two-dimensional bidirectional reflectance distribution function (BRDF) is used to simulate and validate ocean glint reflectances at an infrared wavelength (1036 nm) by matching model results with a complete set of BRDF measurements obtained from the NASA cloud absorption radiometer (CAR) deployed on an aircraft. The surface roughness is then obtained through a retrieval algorithm and is used to extend the simulation into the visible spectral range where diffuse reflectance becomes important. In general, the simulated reflectances and surface roughness information are in good agreement with the measurements, and the diffuse reflectance in the visible, ignored in current glint algorithms, is shown to be important. The successful implementation of this new treatment of ocean glint reflectance and surface roughness in DISORT3 will help improve glint correction algorithms in current and future ocean color remote sensing applications.

glint↗

Boundary-Layer Transition on Hollow Cylinders in Supersonic Free Flight as Affected by Mach Number and a Screwthread Type of Surface Roughness

The effects of Mach number and surface-roughness variation on boundary-layer transition were studied using fin-stabilized hollow-tube models in free flight. The tests were conducted over the Mach number range from 2.8 to 7 at a nominally constant unit Reynolds number of 3 million per inch, and with heat transfer to the model surface. A screwthread type of distributed two-dimensional roughness was used. Nominal thread heights varied from 100 microinches to 2100 microinches. Transition Reynolds number was found to increase with increasing Mach number at a rate depending simultaneously on Mach number and roughness height. The laminar boundary layer was found to tolerate increasing amounts of roughness as Mach number increased. For a given Mach number an optimum roughness height was found which gave a maximum laminar run greater than was obtained with a smooth surface.

James, Carlton S.↗

Rough surface improves stability of air- sounding balloons

Aerodynamic stability of balloons used for measuring the intensity and direction of atmospheric winds at various elevations is improved by incorporating a rough surface on the balloons. The rough-surfaced balloon is useful for collecting wind profiles and other meteorological data.

Scoggins, J. R.↗

Polarimetric thermal emission from rough surfaces

Recent theoretical works have suggested the potential of passive polarimetry in the remote sensing of geophysical media. It was shown that the third Stokes parameter U of the thermal emission may become larger for azimuthally asymmetric fields of observation. In order to investigate the potential applicability of passive polarimetry to the remote sensing of ocean surface, measurements of the polarimetric thermal emission from a sinusoidal water surface and a numerical study of the polarimetric thermal emission from randomly rough ocean surfaces were performed. Measurements of sinusoidal water surface thermal emission were performed using a sinusoidal water surface which was created by placing a thin sheet of fiberglass with a sinusoidal profile in two dimensions extended infinitely in the third dimension onto a water surface. The theory of thermal emission from a 'two-layer' periodic surface is derived and the exact solution is performed using both the extended boundary condition method (EBC) and the method of moments (MOM). The theoretical predictions are found to be in good agreement with the experimental results once the effects of the radiometer antenna pattern are included and the contribution of background noise to the measurements is modeled. The experimental results show that the U parameter indicates the direction of periodicity of the water surface and can approach values of up to 30 K for the surface observed. Next, a numerical study of polarimetric thermal emission from randomly rough surfaces was performed. A Monte Carlo technique utilizing an exact method for calculating thermal emission was chosen for the study to avoid any of the limitations of the commonly used approximate methods in rough surface scattering. In this Monte Carlo technique, a set of finite rough surface profiles in two dimensions with desired statistics was generated and extended periodically. The polarimetric thermal emission from each surface of the set was then calculated using both the EBC and the MOM and the results were averaged. The surface statistics chosen were intended to model a wind perturbed ocean surface in the X to Ku band microwave region. The results indicate that the U parameter is sensitive to the azimuthal angle between the surface periodicity and the looking angle and to the rms height of the surface, and that the U parameter is fairly insensitive to variations in polar angle, permittivity, surface power law spectrum, and surface spectrum high frequency cutoff. These properties give further strength to the idea of using the U parameter to detect wind direction over the ocean.

Johnson, J. T.↗

SURFACE ROUGHNESS REDUCTION AND PERFORMANCE OF Nb3Sn FILM FOR SRF APPLICATIONS

Nb3Sn offers better RF performance (Q and Eacc) than Nb at any given temperature because of its superior superconducting properties. The potential deployment of Nb3Sn-coated SRF cavities at 4 K, delivering similar performance to that of Nb cavities at 2 K, will be a transformational technology to enable new classes of SRF accelerator applications. A clean and smooth surface can enhance the performance of the Nb3Sn-coated cavity, typically, the attainable acceleration gradient. The reduction of surface roughness is often linked with a correlative reduction in average coating thickness and grain size. A new approach to enhance the nucleation centers using the pre-deposition of Sn on Nb is introduced for surface roughness reduction. Besides Sn supply's careful tuning, the temperature profiles were varied to engineer the coating surface with reduced roughness as low as ~40 nm in 20 µm × 20 µm AFM scans, one-third that of the typical coating. Electropolishing of coated sample shows surface a clear surface smoothening. A few sets of coating parameters were used to coat 1.3 GHz sin-gle-cell cavities to understand the effects of roughness variation on the RF performance. This presentation discusses ways to reduce surface roughness with results from a systematic analysis of the samples and Nb3Sn-coated single-cell cavities.

Pudasaini, Uttar↗

SURFACE ROUGHNESS REDUCTION AND PERFORMANCE OF Nb3Sn FILM FOR SRF APPLICATIONS

Nb3Sn offers better RF performance (Q and Eacc) than Nb at any given temperature because of its superior superconducting properties. The potential deployment of Nb3Sn-coated SRF cavities at 4 K, delivering similar performance to that of Nb cavities at 2 K, will be a transformational technology to enable new classes of SRF accelerator applications. A clean and smooth surface can enhance the performance of the Nb3Sn-coated cavity, typically, the attainable acceleration gradient. The reduction of surface roughness is often linked with a correlative reduction in average coating thickness and grain size. A new approach to enhance the nucleation centers using the pre-deposition of Sn on Nb is introduced for surface roughness reduction. Besides Sn supply's careful tuning, the temperature profiles were varied to engineer the coating surface with reduced roughness as low as ~40 nm in 20 µm × 20 µm AFM scans, one-third that of the typical coating. Electropolishing of coated sample shows surface a clear surface smoothening. A few sets of coating parameters were used to coat 1.3 GHz sin-gle-cell cavities to understand the effects of roughness variation on the RF performance. This presentation discusses ways to reduce surface roughness with results from a systematic analysis of the samples and Nb3Sn-coated single-cell cavities.

Pudasaini, Uttar↗

Selection of remote sensing techniques - Surface roughness information from 3 cm wavelength SLAR images

The value of SLAR (Side-Looking Airborne Radar) image data for detecting and measuring small-scale surface roughness is examined, using as an example the Cottonball Basin in Death Valley National Monument, California. The SLAR image was obtained by an X-band (3 cm wavelength) synthetic aperture radar system operated at an altitude of 10,732 m above sea level. The polarization of the transmitted and received signals was horizontal. Film density values were used to produce color hypsometric maps of small-scale surface irregularities. It is shown that semi-quantitative surface roughness information, from uniquely flat surfaces such as the Cottonball Basin, can be obtained by analysis of 3 cm wavelength SLAR images calibrated by limited field measurements. Quantitative roughness data could be obtained with proper consideration of modifying surface and radar system parameters.

Schaber, G. G.↗