Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Exploiting Acoustic Anisotropy to Detect Recrystallization in a Ni Single Crystal Using Ultrasonic Nondestructive Inspection

Ultrasonic inspection was used to detect regions of recrystallization (RX) within a single crystal of Ni. RX can produce polycrystalline regions within single-crystal (SX) materials. Because RX regions act as initiator sites for failure by fatigue-crack growth in otherwise SX Ni-based superalloys, RX is an issue of direct concern for the service life of high-performance turbine blades. Detection and discrimination of RX regions in single-crystal materials are significant challenges for current nondestructive inspection technologies. The present study leverages the elastic anisotropy of single crystals, which produces acoustic anisotropy, to ultrasonically detect and characterize RX regions produced within single-crystal specimens. Single crystals of pure Ni were processed to create controlled regions of RX. These specimens were ultrasonically examined in an immersion tank using a high-resolution, polyvinylidene fluoride transducer to detect acoustic impedance changes across the boundaries between different crystals (i.e., grains) within the RX region. Data from time-of-flight and absolute peak amplitude measurements were used to create acoustic images that were compared against electron microscope images of the RX regions. The ultrasonic inspection technique described here successfully detected not only the locations of RX regions, but also the approximate sizes and shapes of the RX regions.

36 MATERIALS SCIENCE↗

Multi-objective optimization of sustainable aviation fuel production pathways in the U.S. Corn Belt

As a potential source of low-carbon transportation energy, biofuels offer certain advantages over vehicle electrification (e.g., lower societal vulnerability to grid failures, and improved range of sustainable aviation), but also several challenges, including cost, carbon intensity, and land usage. There are also well-founded concerns that biofuel supply chains could be disrupted if extreme weather events impact feedstock yields. In this paper, we explore the use of multi-objective optimization to identify biofuel production pathways that balance cost, greenhouse gas emissions, and supply vulnerability to extreme weather. We compare the use of three different many-objective evolutionary algorithms and linear programming in optimizing biomass cultivation decisions in the U.S. Corn Belt under weather uncertainty using historical, modeled, and synthetic yield data. We consider four feedstock choices (corn, soy, switchgrass, and algae) with two land types (agricultural and marginal lands) and evaluate decisions using three alternative spatial resolutions (ranging from the USDA agricultural district level to the state level). Results show that feedstock choice is the primary driver of objective performance (i.e., the position and shape of 3D, approximate Pareto frontiers). Spatial diversification is a less effective tool in reducing exposure to weather-caused drops in crop yield.

09 BIOMASS FUELS↗

Active Radiative Thermal Switching with Graphene Plasmon Resonators

We theoretically demonstrate a near-field radiative thermal switch based on thermally excited surface plasmons in graphene resonators. The high tunability of graphene enables substantial modulation of near-field radiative heat transfer, which, when combined with the use of resonant structures, overcomes the intrinsically broadband nature of thermal radiation. In canonical geometries, we use nonlinear optimization to show that stacked graphene sheets offer improved heat conductance contrast between “ON” and “OFF” switching states and that a >10× higher modulation is achieved between isolated graphene resonators than for parallel graphene sheets. In all cases, we find that carrier mobility is a crucial parameter for the performance of a radiative thermal switch. Furthermore, we derive shape-agnostic analytical approximations for the resonant heat transfer that provide general scaling laws and allow for direct comparison between different resonator geometries dominated by a single mode. The presented scheme is relevant for active thermal management and energy harvesting as well as probing excited-state dynamics at the nanoscale.

30 DIRECT ENERGY CONVERSION↗

Optical Response of Oriented and Highly Anisotropic Subwavelength Metallic Nanostructure Arrays

Here we describe the optical transmission response of novel coatings with subwavelength metallic structures based on a quasi-open ring resonator design fabricated via a combination of nanoimprint lithography and metal sputtering. This offers a relatively simple approach to the fabrication of dense arrays of optically responsive subwavelength structures over large areas with an oriented two-dimensional array of parallel Au nanoshells. The cross-section of the individual lines is “L” shaped with an approximately 95 nm width, 75 nm height, and pitch of 140 nm to yield a resonant optical response in the visible/near infrared spectrum. Along the long axis of the shells, the geometry is wire-like and quasi-infinite in length compared to the cross-section. This highly anisotropic structure has a strongly polarization-dependent optical response. The coatings are characterized via optical transmission measurements as a function of wavelength, polarization, and angle are presented along with complementary numerical modeling results predicting the resonance shift with corresponding changes in fabrication parameters.

nanostructure, subwavelength, optics, resonance↗

Ions in solution: Density corrected density functional theory (DC-DFT)

Standard density functional approximations often give questionable results for odd-electron radical complexes, with the error typically attributed to self-interaction. In density corrected density functional theory (DC-DFT), certain classes of density functional theory calculations are significantly improved by using densities more accurate than the self-consistent densities. We discuss how to identify such cases, and how DC-DFT applies more generally. To illustrate, we calculate potential energy surfaces of HO·Cl{sup −} and HO·H{sub 2}O complexes using various common approximate functionals, with and without this density correction. Commonly used approximations yield wrongly shaped surfaces and/or incorrect minima when calculated self consistently, while yielding almost identical shapes and minima when density corrected. This improvement is retained even in the presence of implicit solvent.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Correlation between thermodynamic anomalies and pathways of ice nucleation in supercooled water

The well-known classical nucleation theory (CNT) for the free energy barrier towards formation of a nucleus of critical size of the new stable phase within the parent metastable phase fails to take into account the influence of other metastable phases having density/order intermediate between the parent metastable phase and the final stable phase. This lacuna can be more serious than capillary approximation or spherical shape assumption made in CNT. This issue is particularly significant in ice nucleation because liquid water shows rich phase diagram consisting of two (high and low density) liquid phases in supercooled state. The explanations of thermodynamic and dynamic anomalies of supercooled water often invoke the possible influence of a liquid-liquid transition between two metastable liquid phases. To investigate both the role of thermodynamic anomalies and presence of distinct metastable liquid phases in supercooled water on ice nucleation, we employ density functional theoretical approach to find nucleation free energy barrier in different regions of phase diagram. The theory makes a number of striking predictions, such as a dramatic lowering of nucleation barrier due to presence of a metastable intermediate phase and crossover in the dependence of free energy barrier on temperature near liquid-liquid critical point. These predictions can be tested by computer simulations as well as by controlled experiments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rotational study of the NH{sub 3}–CO complex: Millimeter-wave measurements and ab initio calculations

The rotational spectrum of the van der Waals complex NH{sub 3}–CO has been measured with the intracavity OROTRON jet spectrometer in the frequency range of 112–139 GHz. Newly observed and assigned transitions belong to the K = 0–0, K = 1–1, K = 1–0, and K = 2–1 subbands correlating with the rotationless (j{sub k}){sub NH3} = 0{sub 0} ground state of free ortho-NH{sub 3} and the K = 0–1 and K = 2–1 subbands correlating with the (j{sub k}){sub NH3} = 1{sub 1} ground state of free para-NH{sub 3}. The (approximate) quantum number K is the projection of the total angular momentum J on the intermolecular axis. Some of these transitions are continuations to higher J values of transition series observed previously [C. Xia et al., Mol. Phys. 99, 643 (2001)], the other transitions constitute newly detected subbands. The new data were analyzed together with the known millimeter-wave and microwave transitions in order to determine the molecular parameters of the ortho-NH{sub 3}–CO and para-NH{sub 3}–CO complexes. Accompanying ab initio calculations of the intermolecular potential energy surface (PES) of NH{sub 3}–CO has been carried out at the explicitly correlated coupled cluster level of theory with single, double, and perturbative triple excitations and an augmented correlation-consistent triple zeta basis set. The global minimum of the five-dimensional PES corresponds to an approximately T-shaped structure with the N atom closest to the CO subunit and binding energy D{sub e} = 359.21 cm{sup −1}. The bound rovibrational levels of the NH{sub 3}–CO complex were calculated for total angular momentum J = 0–6 on this intermolecular potential surface and compared with the experimental results. The calculated dissociation energies D{sub 0} are 210.43 and 218.66 cm{sup −1} for ortho-NH{sub 3}–CO and para-NH{sub 3}–CO, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microwave spectroscopy of the seeded binary and ternary clusters CO-(pH{sub 2}){sub 2}, CO-pH{sub 2}-He, CO-HD, and CO-(oD{sub 2}){sub N=1,2}

We report the Fourier transform microwave spectra of the a-type J = 1-0 transitions of the binary and ternary CO-(pH{sub 2}){sub 2}, CO-pH{sub 2}-He, CO-HD, and CO-(oD{sub 2}){sub N=1,2} clusters. In addition to the normal isotopologue of CO for all clusters, we observed the transitions of the minor isotopologues, {sup 13}C{sup 16}O, {sup 12}C{sup 18}O, and {sup 13}C{sup 18}O, for CO-(pH{sub 2}){sub 2} and CO-pH{sub 2}-He. All transitions lie within 335 MHz of the experimentally or theoretically predicted values. In comparison to previously reported infrared spectra [Moroni et al., J. Chem. Phys. 122, 094314 (2005)], we are able to tentatively determine the vibrational shift for CO-pH{sub 2}-He, in addition to its b-type J = 1-0 transition frequency. The a-type frequency of CO-pH{sub 2}-He is similar to that of CO-He{sub 2} [Surin et al., Phys. Rev. Lett. 101, 233401 (2008)], suggesting that the pH{sub 2} molecule has a strong localizing effect on the He density. Perturbation theory analysis of CO-oD{sub 2} reveals that it is approximately T-shaped, with an anisotropy of the intermolecular potential amounting to ∼9 cm{sup −1}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rotational study of the CH{sub 4}–CO complex: Millimeter-wave measurements and ab initio calculations

The rotational spectrum of the van der Waals complex CH{sub 4}–CO has been measured with the intracavity OROTRON jet spectrometer in the frequency range of 110–145 GHz. Newly observed and assigned transitions belong to the K = 2–1 subband correlating with the rotationless j{sub CH4} = 0 ground state and the K = 2–1 and K = 0–1 subbands correlating with the j{sub CH4} = 2 excited state of free methane. The (approximate) quantum number K is the projection of the total angular momentum J on the intermolecular axis. The new data were analyzed together with the known millimeter-wave and microwave transitions in order to determine the molecular parameters of the CH{sub 4}–CO complex. Accompanying ab initio calculations of the intermolecular potential energy surface (PES) of CH{sub 4}–CO have been carried out at the explicitly correlated coupled cluster level of theory with single, double, and perturbative triple excitations [CCSD(T)-F12a] and an augmented correlation-consistent triple zeta (aVTZ) basis set. The global minimum of the five-dimensional PES corresponds to an approximately T-shaped structure with the CH{sub 4} face closest to the CO subunit and binding energy D{sub e} = 177.82 cm{sup −1}. The bound rovibrational levels of the CH{sub 4}–CO complex were calculated for total angular momentum J = 0–6 on this intermolecular potential surface and compared with the experimental results. The calculated dissociation energies D{sub 0} are 91.32, 94.46, and 104.21 cm{sup −1} for A (j{sub CH4} = 0), F (j{sub CH4} = 1), and E (j{sub CH4} = 2) nuclear spin modifications of CH{sub 4}–CO, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A DEEP 1.2 mm MAP OF THE LOCKMAN HOLE NORTH FIELD

We present deep 1.2 mm continuum mapping of a 566 arcmin{sup 2} area within the Lockman Hole North (LHN) field, previously a target of the Spitzer Wide-Area Infrared Extragalactic survey and extremely deep 20 cm mapping with the Very Large Array, which we have obtained using the Max-Planck millimeter bolometer (MAMBO) array on the IRAM 30 m telescope. After filtering, our full map has an rms sensitivity ranging from 0.45 to 1.5 mJy beam{sup -1}, with an average of 0.75 mJy beam{sup -1}. Using the pixel flux distribution (PFD) in a map made from our best data, we determine the shape, normalization, and approximate flux density cutoff for 1.2 mm number counts well below our nominal sensitivity and confusion limits. After validating our full data set through comparison with this map, we successfully detect 41 1.2 mm sources with signal-to-noise ratio (S/N) > 4.0 and S{sub 1.2{sub mm}} {approx_equal} 2-5 mJy. We use the most significant of these detections to directly determine the integral number counts down to 1.8 mJy, which are consistent with the results of the PFD analysis. Ninety-three percent of our 41 individual detections have 20 cm counterparts, 49% have Spitzer/MIPS 24 {mu}m counterparts, and one may have a significant Chandra X-ray counterpart. We resolve {approx_equal} 3% of the cosmic infrared background (CIB) at 1.2 mm into significant detections and directly estimate a 0.05 mJy faint-end cutoff for the counts that is consistent with the full intensity of the 1.2 mm CIB. The median redshift of our 17 detections with spectroscopic or robust photometric redshifts is z{sub median} = 2.3, and rises to z{sub median} = 2.9 when we include redshifts estimated from the radio/far-infrared spectral index. By using a nearest neighbor and angular correlation function analysis, we find evidence that our S/N > 4.0 detections are clustered at the 95% confidence level.

79 ASTRONOMY AND ASTROPHYSICS↗

Physical properties of tidal features of interacting disk galaxies: Three-dimensional self-consistent models

Using self-consistent three-dimensional (3D) N-body simulations, we investigate the physical properties of nonaxisymmetric features in a disk galaxy created by a tidal interaction with its companion. The primary galaxy consists of a stellar disk, a bulge, and a live halo, corresponding to Milky-Way-type galaxies, while the companion is represented by a halo alone. We vary the companion mass and the pericenter distance to explore situations with differing tidal strength parameterized by either the relative tidal force P or the relative imparted momentum S. We find that the formation of a tidal tail in the outer parts requires P≳0.05 or S≳0.07. A stronger interaction results in a stronger, less wound tail that forms earlier. Similarly, a stronger tidal forcing produces stronger, more loosely wound spiral arms in the inner parts. The arms are approximately logarithmic in shape, with both amplitude and pitch angle decaying with time. The derived pattern speed decreases with radius and is close to the Ω−κ/2 curve at late time, with Ω and κ denoting the angular and epicycle frequencies, respectively. This suggests that the tidally induced spiral arms are most likely kinematic density waves weakly modified by self-gravity. Compared to the razor-thin counterparts, arms in the 3D models are weaker, have a smaller pitch angle, and wind and decay more rapidly. The 3D density structure of the arms is well described by the concentrated and sinusoidal models when the arms are in the nonlinear and linear regimes, respectively. We demonstrate that dynamical friction between interacting galaxies transfers the orbital angular momentum of one galaxy to the spin angular momentum of the companion halo.

79 ASTRONOMY AND ASTROPHYSICS↗

Survey geometry and the internal consistency of recent cosmic shear measurements

We explore the impact of an update to the typical approximation for the shape noise term in the analytic covariance matrix for cosmic shear experiments that assumes the absence of survey boundary and mask effects. We present an exact expression for the number of galaxy pairs in this term based on the survey mask, which leads to more than a factor of three increase in the shape noise on the largest measured scales for the Kilo-Degree Survey (KiDS-450) real-space cosmic shear data. We compare the result of this analytic expression to several alternative methods for measuring the shape noise from the data and find excellent agreement. This update to the covariance resolves any internal model tension evidenced by the previously large cosmological best-fitting χ 2 for the KiDS-450 cosmic shear data. The best-fitting χ 2 is reduced from 161 to 121 for 118 degrees of freedom. We also apply a correction to how the multiplicative shear calibration uncertainty is included in the covariance. This change shifts the inferred amplitude of the correlation function to higher values. In conclusion, we find that this improves agreement of the KiDS-450 cosmic shear results with Dark Energy Survey Year 1 and Planck results.

79 ASTRONOMY AND ASTROPHYSICS↗

Survey geometry and the internal consistency of recent cosmic shear measurements

Here, we explore the impact of an update to the typical approximation for the shape noise term in the analytic covariance matrix for cosmic shear experiments that assumes the absence of survey boundary and mask effects. We present an exact expression for the number of galaxy pairs in this term based on the the survey mask, which leads to more than a factor of three increase in the shape noise on the largest measured scales for the Kilo-Degree Survey (KIDS-450) real-space cosmic shear data. We compare the result of this analytic expression to several alternative methods for measuring the shape noise from the data and find excellent agreement. This update to the covariance resolves any internal model tension evidenced by the previously large cosmological best-fit $\chi^2$ for the KiDS-450 cosmic shear data. The best-fit $\chi^2$ is reduced from 161 to 121 for 118 degrees of freedom. We also apply a correction to how the multiplicative shear calibration uncertainty is included in the covariance. This change, along with a previously known update to the reported effective angular values of the data vector, jointly shift the inferred amplitude of the correlation function to higher values. Lastly, we find that this improves agreement of the KiDS-450 cosmic shear results with Dark Energy Survey Year 1 and Planck results.

79 ASTRONOMY AND ASTROPHYSICS↗

Cross sections for neutron-induced reactions from surrogate data: Reexamining the Weisskopf-Ewing approximation for ( n , n ' ) and ( n , 2 n ) reactions

Background: Modeling nuclear reaction networks for nuclear science applications and for simulations of astrophysical environments relies on cross section data for a vast number of reactions, many of which have never been measured. Cross sections for neutron-induced reactions on unstable nuclei are particularly scarce, since they are the most difficult to measure. Consequently, we must rely on theoretical predictions or indirect measurements to obtain the requisite reaction data. For compound nuclear reactions, the surrogate reaction method can be used to determine many cross sections of interest. Purpose: Earlier work has demonstrated that cross sections for neutron-induced fission and radiative neutron capture can be determined from a combination of surrogate reaction data and theory. For the fission case, it was shown that the Weisskopf-Ewing approximation, which significantly simplifies the implementation of the surrogate method, can be employed. Capture cross sections cannot be obtained, and require a detailed description of the surrogate reaction process. Here, we examine the validity of the Weisskopf-Ewing approximation for determining unknown (n, n') and (n, 2n) cross sections from surrogate data. Methods: Using statistical reaction calculations with realistic parametrizations, we investigate first whether the assumptions underlying the Weisskopf-Ewing approximation are valid for (n, n') and (n, 2n) reactions on representative target nuclei. We then produce simulated surrogate reaction data and assess the impact of applying the Weisskopf-Ewing approximation when extracting (n, n') and (n, 2n) cross sections in situations where the approximation is not strictly justified. Results: We find that peak cross sections can be estimated using the Weisskopf-Ewing approximation, but the shape of the (n, n') and (n, 2n) cross sections, especially for low neutron energies, cannot be reliably determined without accounting for the angular-momentum differences between the neutron-induced and surrogate reaction. Conclusions: To obtain reliable (n, n') and (n, 2n) cross sections from surrogate reaction data, a detailed description of the surrogate reaction mechanisms is required. To do so for the compound-nucleus energies and decay channels relevant to these reactions, it becomes necessary to extend current modeling capabilities.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Towards AI Based Data Classification for Decision Making During Testing

During the development of high-consequence items, test systems should be capable of differentiating between test failures resulting from narrowly missing requirements versus those indicating potentially catastrophic faults. In many instances, classifying the data corresponds to simply identifying whether measured waveforms have approximately the anticipated shape. Cast in this light, the problem reduces to converting raw data into a form optimal for use with neural network classifiers. This manuscript investigates different means of representing raw data for image classification. Raw data plots and Short Time Fourier Transform (STFT) spectrograms are classified by both custom built, small-scale, Convolution Neural Networks (CNN) and open-source, multi-million parameter, pre-trained deep CNNs. In the case of time varying frequency content, the STFTs provide images with greater detail and can be accurately classified with simpler networks. This requires less memory and runs faster than classifying the raw data using the more sophisticated options—making STFTs optimal for applications with memory constraints. STFTs are not a panacea. In some cases the time-domain signal contains useful information that should not be discarded. Rather than using raw data or STFTs, the images can be constructed from both by using red and green channels of an RGB image to visualize the real and imaginary components of the transform, with the raw data occupying the blue channel.

97 MATHEMATICS AND COMPUTING↗

Reynolds number effects on the aerodynamic characteristics of irregular planform wings at Mach number 0.3

The subsonic aerodynamic characteristics of a series of irregular planform wings were studied in wind tunnel tests conducted at M = 0.3 over a range of Reynolds numbers from 1.6 million to 26 million/m. The five basic wing planforms varied from a trapezoidal to a delta shape. Leading edge extensions, added to the basic shape, varied in approximately 5 deg increments from the wing leading edge sweep-back angle to a maximum 80 deg. Most of the tests were conducted using an NACA 0008 airfoil section with grit boundary layer trips. Tests were also conducted using an NACA 0012 airfoil section and an 8% thick wedge. In addition, the effect of free transition (no grit) was investigated. A body was used on all models.

Kruse, R. L.↗

Narrow zone heating by a new radiation focusing technique - Toroidal ellipsoid furnace

The paper describes the design of a toroidal ellipsoid furnace for narrow zone heating of materials in sealed transparent ampoules. The heater is a toroid flattened to an elliptical cross section like a partially inflated inner tube resting on a horizontal surface. The foci of the ellipsoid are two concentric rings. The outer focus is occupied by a heater wire, and the inner focus is arranged to fall on the surface of the cylindrical ingot within its transparent capsule. One advantage of the new furnace is that the wire heater closely approximates the ideal shape, lying along an extended line focus, as opposed to the elusive point source of the Costello furnace. Also, the ingot is heated uniformly around its circumference.

Davidson, M. C.↗

Spectrophotometry of Michigan-Tololo quasars

Emission-line quasar characteristics are confirmed for 80% of the objects observed, including at least four new quasars with spectral features indicative of supernova-like outflow. Approximately 73% of the redshifts predicted from the discovery plates are found accurate with a mean error in z of 0.03, and a large range of z (from about 0.1 to 3.16) is represented in the sample. The observed redshift distribution for quasars is marginally consistent with a constant co-moving quasar density above z approximately 2.0. The shape of the redshift distribution may be used as an isotropy probe with a cosmic time resolution of a few times one-hundred million years in the early universe; therefore, continued surveys of this sort are important even if accurate magnitudes are not determined.

Lewis, D. W.↗